I'm new here and sorry for the nooB-ish question, but I'm going to be picking up an 8525 in the next week or so, and have been reading the wiki, and many posts like a madman...
I'm intending to flash a WM06 to it when I get it (LVSW's Pro 06 most likely) and I just want to be sure I understand the procedure. I have been reading the wiki (for the past couple days) and finally have read myself into a corner, so thought I'd ask.
It is likely I'm going to get the phone from ebay or something, so I'm not too concerned about the carrier's warranty. Besides, any time I tried to warranty a phone through Cingular in the past has been a headache.
That said, the steps I think I need to take are as follows:
1) us pof's v3 SIM and CID unlocker. I plan on unlocking both SIM and CID. Currently I am on Cingular, but I'd like to do this step in case I'm not on Cingular, or end up travelling and go with a pay as you go type of plan while abroad. And the CID, well I know I'll be going to a non Cingular branded ROM.
2) (not sure about this part)- load hard SPL onto the phone... but if I'm CID unlocking it, do I still need to do this?
3) run the RUU and upgrade to the LVSW (WM6 Style) Custom ROM, with the 1.34 radio, 1.10Oli SPL, and HTC Boot 0108
4) do it again, but with the LVSW (Pro Style) 15/3/07, which will give me the OS only, in the Pro Style look I'm after
5) flash it to the newer 1.38 radio sans GPS
Two or three days ago, I wouldn't have even half understood what I just wrote. I'm hoping I got it... where I am having issues is with the myriad different "use this method to flash your phone and not brick it" things in the wiki. I'm not by any means new to phone flashing, but with like 8-9 phones in the last couple years, all of which I modded in some way or another, this is my first foray outside Motorola.
So, did I get it? Or am I well on the way to owning a neat doorstop?
Thanks for any constructive input you all might have.
Sounds fine to me. But, you don't need the SuperCID to flash non-cingular as long as you're using the custom RUU's and SSPL.
Definately flash hard-spl, (although, that is the same as 1.10.Oli), I'd still probably flash it before anything else just to make sure.
Also, I'd probably check out Oli's "Mount ExtRom without SuperCID" thread if you still want access to the extrom.. Basically, if you use this and skip pof's unlocker, you'll still have Cingular CID, but, all the benefits of SuperCID.
Only use pof's unlocker if you want the sim unlock.. WHICH Cingular will give to you by calling customer service and requesting it after telling them you are traveling to Europe, etc..
Up to you though...
If you're going to use pof's unlock etc and Hard SPL why flash the custom rom before the pro style one. Can't you just go straight to the second rom?
@LegolasTheElf- thanks! I'll look into those options.
@randomelements- yep, I could. I didn't realize that the Oli SPL was pushing Hard SPL to the phone... And, with upgrading the radio, I guess it really doesn't matter.... I was going to go with that LVSW custom rom for the upgraded radio... it made it on the list of things to do on Sat. Then, Sunday I was reading the 1.38 (Hermes) radio upgrade thread, and decided to throw that on the list too.
I'm going to change my mind.. Here's the process:
1. Pof's unlocker (if you want)
2. Install Oli's Hard-SPL
3. Install 1.38.00.10 radio
4. Install OS *only* LVSW pro
5. Install Oli's Mount ExtRom without supercid if you didn't already unlock with pof's unlocker.
That will mean only one radio flash (radio being the leading cause of bricks), a good chance of fixing it (Oli's BL), and the OS you want. ExtRom is ignored as the WM6 roms don't use it anyways...
I concur.
LegolasTheElf said:
I'm going to change my mind.. Here's the process:
1. Pof's unlocker (if you want)
2. Install Oli's Hard-SPL
3. Install 1.38.00.10 radio
4. Install OS *only* LVSW pro
5. Install Oli's Mount ExtRom without supercid if you didn't already unlock with pof's unlocker.
That will mean only one radio flash (radio being the leading cause of bricks), a good chance of fixing it (Oli's BL), and the OS you want. ExtRom is ignored as the WM6 roms don't use it anyways...
Click to expand...
Click to collapse
Hey, great, thanks!
For some reason I didn't pick up on the Radio flash being the cause of the bricks... I just thought it was with the RUU and CID interferance.
over2land said:
Hey, great, thanks!
For some reason I didn't pick up on the Radio flash being the cause of the bricks... I just thought it was with the RUU and CID interferance.
Click to expand...
Click to collapse
That's only half the cause. The other half is boneheads and ****wits (to use a coined term on here.. Thanks Oli!) that can't/don't read before they charge forward and install crap without any idea of what the hell they're doing.
[email protected] ****wits, I'll have to use that one.
Thanks again.
Related
hi all,
i've just bought a t-mobile vario 2
i;ve read the wiki & a few of the posts regarding upgrading
but to be honest it has so much information & sometimes the information is contradictory.. so it gets confusing
i've been using the uni for a year now
my point is
i want 2 upgrade my hermes 2 wm6
my boot screen says
herm300
IPL-1.01
SPL 1.40.Olipro
i can use a different/other sim card than t-mobile
how do i chek if my hermes is CID unlocked
and what radio i'm using & what's my bootloader number??
i try 2 read the splash screen after soft reset but the radio version goes away pretty fast
do i run POF's unlocker v3a? is it safe to run again, even if my phone is cid unlocked?
in order 2 upgrade 2 wm6
do i need to install olipros hard spl 2.10? and then run customruu?
this is what i mean by confusing?
i've upgraded my magician, uni & wizard
however they all had pretty easy/self explanatory directions?
i'm sorry for sounding like a noob, but its new territory....
thanx in advance
Is there a specific reason you want to CID the device? T-Mobile's data plan s pretty great so I have never seen the need to use another sim in my vario. You dont need to CID unlock to upgrade the rom.
As long as you have installed Olipro's spl to protect against bricking your phone it should be fairly safe to install a wm6 rom. If not, definitely install the current version of hard spl.
Once you have installed SPL, you then run the RUU.exe file that usually comes with the rom. Tha majority will have a tick box on the first page that says auto detect, which will check which version of spl you have installed and then run itself accordingly. It is best to have the current hardspl installed though.
Most of them dont touch your extended rom and only replace the OS rom contents. T-Mob's wm5 extended rom customizations wont work with wm6 anyway so you will need to go looking here for a cab file called (I Believe) tmobileukfixed.cab.
You will also need to look for newer versions of your pocket pc software as some older ones dont play nice with WM6.
Good luck, and if in doubt, read MrVanx's upgrade guide here: http://www.mrvanx.org/cms/
chrisjasper said:
Is there a specific reason you want to CID the device? T-Mobile's data plan s pretty great so I have never seen the need to use another sim in my vario. You dont need to CID unlock to upgrade the rom.
As long as you have installed Olipro's spl to protect against bricking your phone it should be fairly safe to install a wm6 rom. If not, definitely install the current version of hard spl.
Once you have installed SPL, you then run the RUU.exe file that usually comes with the rom. Tha majority will have a tick box on the first page that says auto detect, which will check which version of spl you have installed and then run itself accordingly. It is best to have the current hardspl installed though.
Most of them dont touch your extended rom and only replace the OS rom contents. T-Mob's wm5 extended rom customizations wont work with wm6 anyway so you will need to go looking here for a cab file called (I Believe) tmobileukfixed.cab.
You will also need to look for newer versions of your pocket pc software as some older ones dont play nice with WM6.
Good luck, and if in doubt, read MrVanx's upgrade guide here: http://www.mrvanx.org/cms/
Click to expand...
Click to collapse
i dont live in the uK
so the tmobile plan is not the usp
i need to unlock the extende rom as i like 2 install most of my progs on the extended rom and also my ringtones as the sd card takes a cople of seconds b4 it kicks in..
check the wiki under Bootloader information.
Using mtty, there is a command to check CID status.
todd_jg said:
check the wiki under Bootloader information.
Using mtty, there is a command to check CID status.
Click to expand...
Click to collapse
hi
i've managed 2 find out that my phones supercid
however i cant get mtty 2 work
i put the phone in bootloader
then i conect the phone via usb
when i rum mtty
it says usb port cannot open
i tried mtty 1.42 as well.....
I have been reading all across the forums how to CID unlock, upgrade etc. However, I am not able to find the ways to do seeminly essential homework before trying to upgrade. These for me are:-
* Finding a way to completely backup all the stuff from original tytn. Like ROM, SPL, IPL, Radio, CIDlock etc. I feel that this is important as if ever I feel like going to the tried old one I should be able to and to preserve the warranty also. Also, the method to roll back if needed. This should be covering re CID locking the phone etc.
It makes sense to create a way to bring the phone to its completlely original shape if we need it
Thanks
Alber
alber786 said:
I have been reading all across the forums how to CID unlock, upgrade etc. However, I am not able to find the ways to do seeminly essential homework before trying to upgrade. These for me are:-
* Finding a way to completely backup all the stuff from original tytn. Like ROM, SPL, IPL, Radio, CIDlock etc. I feel that this is important as if ever I feel like going to the tried old one I should be able to and to preserve the warranty also. Also, the method to roll back if needed. This should be covering re CID locking the phone etc.
It makes sense to create a way to bring the phone to its completlely original shape if we need it
Thanks
Alber
Click to expand...
Click to collapse
You do not need to back up your spl, ipl, etc. because if you need to roll back you can just reflash them on, and they can be found around here and in the wiki.
You cannot un-CIDunlock, but if you use hardspl v7 it will "trick" your phone into thinking it is (when in reality it isnt) so that you do not have to actually unlock it. If you ever need to send it in you can just flash the old spl over it.
mcorrie1121 said:
You do not need to back up your spl, ipl, etc. because if you need to roll back you can just reflash them on, and they can be found around here and in the wiki.
You cannot un-CIDunlock, but if you use hardspl v7 it will "trick" your phone into thinking it is (when in reality it isnt) so that you do not have to actually unlock it. If you ever need to send it in you can just flash the old spl over it.
Click to expand...
Click to collapse
So you mean that hardspl doesnt CID unlock it? But isnt there really a way to extract the original components and then put them back again ?
thanks
Alber
alber786 said:
So you mean that hardspl doesnt CID unlock it? But isnt there really a way to extract the original components and then put them back again ?
thanks
Alber
Click to expand...
Click to collapse
HardSPL does not CID unlock. pof's Free Unlocker (a sticky thread) does the SIM and CID unlocking. HardSPL is a new set of bootloaders allowing upgrade utilities to access and read/write to the phone. The most important aspect of this (besides bypassing the CID check) is the security - it has some overwrite protection built in to prevent you from accidentally corrupting the bootloader area, rendering your phone a brick. HardSPL is a safety measure.
If you check THE WIKI here on xda for the Hermes, you will find some stuff on extracting. It is most probable that it will be FAR easier to find new versions of everything you have, rather than trying to back up and restore. The wiki contains MANY shipped ROMs to allow you to restore back to basically the original condition. LOOK HERE for MW5 shipped ROMs and LOOK HERE for WM6 shipped ROMs.
todd_jg said:
HardSPL does not CID unlock. pof's Free Unlocker (a sticky thread) does the SIM and CID unlocking. HardSPL is a new set of bootloaders allowing upgrade utilities to access and read/write to the phone. The most important aspect of this (besides bypassing the CID check) is the security - it has some overwrite protection built in to prevent you from accidentally corrupting the bootloader area, rendering your phone a brick. HardSPL is a safety measure.
If you check THE WIKI here on xda for the Hermes, you will find some stuff on extracting. It is most probable that it will be FAR easier to find new versions of everything you have, rather than trying to back up and restore. The wiki contains MANY shipped ROMs to allow you to restore back to basically the original condition. LOOK HERE for MW5 shipped ROMs and LOOK HERE for WM6 shipped ROMs.
Click to expand...
Click to collapse
what about the radio upgrade
the htc108 thing
its confusing
on pof's sticky it says to downgrade the radio if u have the htc 108..
but on the radio upgrade sticky, it says u can upgrade any phone[hermes] using custom ruu..
todd_jg said:
HardSPL does not CID unlock. pof's Free Unlocker (a sticky thread) does the SIM and CID unlocking. HardSPL is a new set of bootloaders allowing upgrade utilities to access and read/write to the phone. The most important aspect of this (besides bypassing the CID check) is the security - it has some overwrite protection built in to prevent you from accidentally corrupting the bootloader area, rendering your phone a brick. HardSPL is a safety measure.
If you check THE WIKI here on xda for the Hermes, you will find some stuff on extracting. It is most probable that it will be FAR easier to find new versions of everything you have, rather than trying to back up and restore. The wiki contains MANY shipped ROMs to allow you to restore back to basically the original condition. LOOK HERE for MW5 shipped ROMs and LOOK HERE for WM6 shipped ROMs.
Click to expand...
Click to collapse
Thanks a lot for the reply, I appreciate the time you spent in expaining this to me and providing these links.
I was wondering if HARDSPL is like shelltool where it will only allow upgrade or flashing of OS part. So, once I use the HARDSPL and flash say HTC official WM6 release or Dopod WM6, will I be ableto to get the bundled radio and SPL and IPL upgrades from these ROMS? and if yes then will HARDSPL get replaced by these SPLs and IPLs built into the ROMS? One more thing, will an upgrade like that can brick the phone as if I rum the official ROM it will try to upgrade the SPL and IPL (I am not sure).
What is the preferred way of upgrading ? unlocking CID by the tool or HARDSPL ?
I have read somewhere that lockwiz tool used for Wizard can save CID also and some tool and put it back also but I dont know how and if the same tool can do it for hermes?
Regards,
Alber
alber786 said:
Thanks a lot for the reply, I appreciate the time you spent in expaining this to me and providing these links.
I was wondering if HARDSPL is like shelltool where it will only allow upgrade or flashing of OS part. So, once I use the HARDSPL and flash say HTC official WM6 release or Dopod WM6, will I be ableto to get the bundled radio and SPL and IPL upgrades from these ROMS? and if yes then will HARDSPL get replaced by these SPLs and IPLs built into the ROMS? One more thing, will an upgrade like that can brick the phone as if I rum the official ROM it will try to upgrade the SPL and IPL (I am not sure).
What is the preferred way of upgrading ? unlocking CID by the tool or HARDSPL ?
I have read somewhere that lockwiz tool used for Wizard can save CID also and some tool and put it back also but I dont know how and if the same tool can do it for hermes?
Regards,
Alber
Click to expand...
Click to collapse
Most cooked roms are os only, but a few have a radio, etc. included. If its os only, flashing will only change the os. You can separately flash radio.
Hardspl is the best because its reversible. Well thats not the best word to describe it....id say because its not permanent. But u know what i mean
alber786 said:
Thanks a lot for the reply, I appreciate the time you spent in expaining this to me and providing these links.
I was wondering if HARDSPL is like shelltool where it will only allow upgrade or flashing of OS part. So, once I use the HARDSPL and flash say HTC official WM6 release or Dopod WM6, will I be ableto to get the bundled radio and SPL and IPL upgrades from these ROMS? and if yes then will HARDSPL get replaced by these SPLs and IPLs built into the ROMS? One more thing, will an upgrade like that can brick the phone as if I rum the official ROM it will try to upgrade the SPL and IPL (I am not sure).
What is the preferred way of upgrading ? unlocking CID by the tool or HARDSPL ?
I have read somewhere that lockwiz tool used for Wizard can save CID also and some tool and put it back also but I dont know how and if the same tool can do it for hermes?
Regards,
Alber
Click to expand...
Click to collapse
Mcorrie1121 is right. I will add a couple of things.
1. HardSPL is not *necessary* for flashing anything, it only makes it safer and allows you to flash ROMs with CIDs that do not match your device without CID unlocking. Your ROM is basically a few parts - OS, Radio, IPL, SPL, ExtROM, MainSplash and SubSplash. The HardSPL will replace the SPL only. Most non-carrier ROM releases are OS only. Most carrier ROMs (as you pointed out) have ALL of these things. As Mcorrie1121 pointed out, you can easily find a radio - check the wiki, search, etc.
2. Once you have upgraded to a cooked ROM (and HardSPL), you will still be able to upgrade to a Shipped Official ROM. You may need to "unpack" it and use the CustomRUU instead of the shipped updater. That is OK though.
3. HardSPL will not allow overwriting of the IPL/SPL except by another HardSPL (see mrvanx.org downgrade guides). You will not have a problem. It will keep your bootloader zone safe.
4. I don't think there is a preferred way. Some people unlock CID, others do not. There is no reason to *not* unlock it, unless you plan to send it back - and I have never heard of someone getting service rejected for this reason. Wring ROM, yes. CID unlocked, no. That said, maybe try without CID unlocking first and then if you find you need to do it for some reason, then do it. You really do not have to do it, since the Custom Updater bypasses the CID check anyway.
5. Regarding the 0108 Radio BL issue, don't worry much about that - it is an old problem. Just don't go below whatever version you have now.
todd_jg said:
Mcorrie1121 is right. I will add a couple of things.
1. HardSPL is not *necessary* for flashing anything, it only makes it safer and allows you to flash ROMs with CIDs that do not match your device without CID unlocking. Your ROM is basically a few parts - OS, Radio, IPL, SPL, ExtROM, MainSplash and SubSplash. The HardSPL will replace the SPL only. Most non-carrier ROM releases are OS only. Most carrier ROMs (as you pointed out) have ALL of these things. As Mcorrie1121 pointed out, you can easily find a radio - check the wiki, search, etc.
2. Once you have upgraded to a cooked ROM (and HardSPL), you will still be able to upgrade to a Shipped Official ROM. You may need to "unpack" it and use the CustomRUU instead of the shipped updater. That is OK though.
3. HardSPL will not allow overwriting of the IPL/SPL except by another HardSPL (see mrvanx.org downgrade guides). You will not have a problem. It will keep your bootloader zone safe.
4. I don't think there is a preferred way. Some people unlock CID, others do not. There is no reason to *not* unlock it, unless you plan to send it back - and I have never heard of someone getting service rejected for this reason. Wring ROM, yes. CID unlocked, no. That said, maybe try without CID unlocking first and then if you find you need to do it for some reason, then do it. You really do not have to do it, since the Custom Updater bypasses the CID check anyway.
5. Regarding the 0108 Radio BL issue, don't worry much about that - it is an old problem. Just don't go below whatever version you have now.
Click to expand...
Click to collapse
Thanks, I appreciate your help. Please tell me if I can put back WM5 back on it after upgrading.
Regards,
Alber
todd_jg said:
Mcorrie1121 is right. I will add a couple of things.
1. HardSPL is not *necessary* for flashing anything, it only makes it safer and allows you to flash ROMs with CIDs that do not match your device without CID unlocking. Your ROM is basically a few parts - OS, Radio, IPL, SPL, ExtROM, MainSplash and SubSplash. The HardSPL will replace the SPL only. Most non-carrier ROM releases are OS only. Most carrier ROMs (as you pointed out) have ALL of these things. As Mcorrie1121 pointed out, you can easily find a radio - check the wiki, search, etc.
2. Once you have upgraded to a cooked ROM (and HardSPL), you will still be able to upgrade to a Shipped Official ROM. You may need to "unpack" it and use the CustomRUU instead of the shipped updater. That is OK though.
3. HardSPL will not allow overwriting of the IPL/SPL except by another HardSPL (see mrvanx.org downgrade guides). You will not have a problem. It will keep your bootloader zone safe.
4. I don't think there is a preferred way. Some people unlock CID, others do not. There is no reason to *not* unlock it, unless you plan to send it back - and I have never heard of someone getting service rejected for this reason. Wring ROM, yes. CID unlocked, no. That said, maybe try without CID unlocking first and then if you find you need to do it for some reason, then do it. You really do not have to do it, since the Custom Updater bypasses the CID check anyway.
5. Regarding the 0108 Radio BL issue, don't worry much about that - it is an old problem. Just don't go below whatever version you have now.
Click to expand...
Click to collapse
Dear, please help me with one thing-I am terribly confused about the procedure to upgrade my JASJAM to WM6. I understand that one way is to CIS unlock it and install on it the official and dopod releases of WM6. I wanted to know how can I do the same using the HARDspl. I know that I can install the HARDSPL but after that what ??? Can I then run the offcial RUU from HTC or Dopod or I am supposed to do it some other way as I am afraid that it may contain the SPL and IPL and can break by phone OR I have to use some customRUU (I dont know) OR I am supposed to extract the OS from these official releases (I dont know how) OR ..
Can you please clear these confusion??
I have:-
* I-Mate JASJAM, CID locked i suppose as when I run official HTC or dopod it says this update utility is not for this
*I really wanted to save my devices complete state and a way to revert it to the way it was like SPL, IPL, OS, Radio, CID lock etc.
PLS pls help
Regards,
Alber
alber786 said:
Dear, please help me with one thing-I am terribly confused about the procedure to upgrade my JASJAM to WM6. I understand that one way is to CIS unlock it and install on it the official and dopod releases of WM6. I wanted to know how can I do the same using the HARDspl. I know that I can install the HARDSPL but after that what ??? Can I then run the offcial RUU from HTC or Dopod or I am supposed to do it some other way as I am afraid that it may contain the SPL and IPL and can break by phone OR I have to use some customRUU (I dont know) OR I am supposed to extract the OS from these official releases (I dont know how) OR ..
Can you please clear these confusion??
I have:-
* I-Mate JASJAM, CID locked i suppose as when I run official HTC or dopod it says this update utility is not for this
*I really wanted to save my devices complete state and a way to revert it to the way it was like SPL, IPL, OS, Radio, CID lock etc.
PLS pls help
Regards,
Alber
Click to expand...
Click to collapse
CLICK THIS LINK
There are upgrade guides there and guides to put it back the way it was (OS, Radio, IPL, SPL, MainSplash and SubSplash) - it is all covered.
The upgrade guides will get you through the upgrade process. The only thing you need to do after that to use an official upgrade is to unrar (using winrar or something) the executable file and take the nbh and us it with the CustomRUU, which can be found HERE .
Is there a way I can unlock my hermes whilst keeping the newest radio (1.54.00.10)?
Yes, load hard spl ver.7 on then pick a rom, any rom that doesnt upgrade the radio rom. Most cooked roms don't have the radio cooked in. Happy upgrading.
ultramag69 said:
Yes, load hard spl ver.7 on then pick a rom, any rom that doesnt upgrade the radio rom. Most cooked roms don't have the radio cooked in. Happy upgrading.
Click to expand...
Click to collapse
VERY incorrect reply.
@ TheOracle
The radio version used in pofs unlocker has been modified to allow CID/SIM unlocking so you must use the package provided in the thread there.
I can't seem to find the thread, I'll keep looking though I'm probably being stupid! Thanks for the help =D
Well I've just unlocked the phone again with CID-Unlock V3a, however it's stuck me with Radio 1.16 . Could I still use Herm_Unlock_v3 etc with the newest radio or will it brick if I don't use Radio 1.16?
Here are the steps needed
1 Download and unzip the unlocker. All of the instructions are included on the zip file. Follow it closely. Read the thread for instructions and common mistakes before you do it. The program will install radio 1.16 which you'll replace with step number 3
http://forum.xda-developers.com/showthread.php?t=293665
2. Install hardspl. Use this guide by mrvanx. Very straightforward. Use a computer with xp, avoid vista.
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=30&Itemid=27
3. Download your radio rom here and install.
http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms
Go back to mrvanx guide on installing radios. Read all the threads and understand what is needed for each step to safely upgrade your device. If you're not sure, it's better to ask again on this thread. I hope this helps and good luck
Also, I think you can ask where you bought the phone to get an unlock code? I know at&t will do it with conditions.
TheOracle said:
Well I've just unlocked the phone again with CID-Unlock V3a, however it's stuck me with Radio 1.16 . Could I still use Herm_Unlock_v3 etc with the newest radio or will it brick if I don't use Radio 1.16?
Click to expand...
Click to collapse
I always unlock using the manual method, so for the last step I transfer HERM_Unlock_v3.exe to my device and run it. Click the unlock button, then select sim and super cid unlock.
Follow the steps I've provided, you should be fine
For future reference, here's mrvanx's hermes guide.
http://forum.xda-developers.com/showthread.php?t=299462
If you decide to upgrade your rom as well, the guide will be a great help.
Hi,
Hopefully someone can tell me the correct guide to upgrade my iMate JasJam from WM5 to WM6? I've read the guides, but there's so much choice I'm confused! I really don't want to brick my phone as I use it for business. I live in New Zealand so do I need to do anything else to get it working on the Vodafone NZ network?
Can someone tell me the guide I should use which will work?
iMate are useless and never released an official WM6 update.
I'm thinking of following this guide but using the Black Satin ROM. Any objections?
following that should be fine BUT first you need to sim/cid unlock your Phone and install hard SPL on it. this will make it easier to fix if something goes wrong. Both programs you need can be found at the top of the list on this part of the forum. PLEASE also read MR Vanx's guide to flashing your phone as it Will definately be beneficial. After Flashing the first 2 things onto your Hermes you can pick whatever rom you want. Black satin is an older rom but fairly stable. Good uck and happy flashing...
Ok, unlock then hard SPL first, got it.
What's newer and more stable than Black Satin then?
Pays, Schapps, these guys really know what they're doing, I personally like TNT se. Thats my preference. What you need to do is search the forum and find a rom you like. Each person likes different things and me telling you what I like may be completely different to what you want or need. Alot of roms come with 3rd party apps cooked in but if you want speed then go for a lite rom. I'm also trying out the 6.1 roms but there have been stability issues. My preference there is Faria-R32 Dr Puttingham WM6.1 HERMES ROM-CUSTOM+CLEAN. It seems to be stable for my purposes. Research and find what you like... Cheers
Sweet I'll check it out. Thanks mate.
Hmm bit confused now. Which do I run first? The unlocker or the Hard SPL?
Because in the 'HTC Hermes SIM & CID Unlock - v3a' instructions iit says "New RUU will make sure HardSPL-1.40 is installed before flashing the radio". As far as I know I don't have any HardSPL on my device at the moment. So that must mean I need to run the HardSPL first? Then the unlocker?
Also as far as HardSPL goes, there is a v9 Hard-SPL-2.60 out. Should I use that or the 2.10 - Hard-SPL-V7??
hardspl first, the sim unlocker. for version, just go with v9.
Yeah did the HardSPL first, then the SIM unlocker. The SIM unlocker actually downgraded the HardSPL to 1.4.olipro so I had to run the HardSPL to bring it back up to the other level 2.60. Weird...
Anyway I'm up and running!
Radio version is now: 1.43.00.00
ROM: Schap's 4.30
The thing I was hoping to eliminate with WM6 was the slow time it takes to dial numbers on the phone. Whenever you dial a key there's like a 1/2sec delay before it appears on the screen. I'd like it to be instant. The delay makes me think the phone is slow and it's really annoying. Anyone know if it can be fixed?
My bro has a Titan and is thinking about having me upgrade but I saw that his bootloader version states 1.04 not the 1.06 that mine was when I flashed (and also the one that the wiki says too). Is the process the same? Should I just use unlocker then upgrade to 2.40 then install radio then DCD? A little wary as it is not my phone. Please be specific when answering. I am planning to do the most recent radio and rom.
serfboreds said:
My bro has a Titan and is thinking about having me upgrade but I saw that his bootloader version states 1.04 not the 1.06 that mine was when I flashed (and also the one that the wiki says too). Is the process the same? Should I just use unlocker then upgrade to 2.40 then install radio then DCD? A little wary as it is not my phone. Please be specific when answering. I am planning to do the most recent radio and rom.
Click to expand...
Click to collapse
In order to flash a dcd rom you need 2.40...Go through the same process you would in order to flash a 3.1.x rom.
prepsssuck said:
In order to flash a dcd rom you need 2.40...Go through the same process you would in order to flash a 3.1.x rom.
Click to expand...
Click to collapse
So it still needs unlocker then 2.40 right? or is unlocker unnecessary now?
Who is his carrier? As forthe bootloader question, I'd be asking Ollipro... I've not seen a bootloader 1.04....
azclown said:
Who is his carrier? As forthe bootloader question, I'd be asking Ollipro... I've not seen a bootloader 1.04....
Click to expand...
Click to collapse
bootloader 1.04 is the "stock" verizon bootloader you should still update to the 2.40 if you plan on having any 3.xx.xx radio's
Just to clarify...
When the phone ships it comes with SPL-1.04 which is the stock bootloader, which is why it doesn't say Olipro.
1.06 is also a "stock" bootloader provided by Olipro which allows you to flash stock roms/radios.
Edit: WINGS 1 - PENS 0!!!!!!
gcincotta said:
Just to clarify...
When the phone ships it comes with SPL-1.04 which is the stock bootloader, which is why it doesn't say Olipro.
1.06 is also a "stock" bootloader provided by Olipro which allows you to flash stock roms/radios.
Edit: WINGS 1 - PENS 0!!!!!!
Click to expand...
Click to collapse
Thanks, I have been flashing since the time you needed the old Olipro to flash the radio and when my brother once before flashed going straight to 2.40 it caused problems. I haven't had a new phone since then and wondered if the unlocker was still necessary. I am gathering that it is not and that you can go straight to 2.40, am I correct?
mogul with slight crack along the frame of screen
i've been reading for a while, and someone wrote that it doesn't matter about the bootloader when returning the phone to the store as long as you have the stock rom. i'm using the newer stock rom (3.35), though i did use the unlocker to put olipro 2.40 on it a while ago to mess with other roms.
the work order for the replacement mogul is already in and it (the new or refurbed mogul) should arrive tomorrow or the next day. should i go through the trouble of putting the stock bootloader on there if i already have the newer stock rom from htc/sprint on my phone?
also, i read that sprint has no warranty (or it's only 30 days). i use total equipment protection for $7 per month (which is how i'm getting a new or refurb mogul because of a case fracture). i'm using the newer stock sprint rom (with gps) and my bootloader says olipro 2.40.
does anyone think that i should be worried if i don't do anything before the new one arrives and just give them the cracked one?
i clearly didn't read the terms and conditions closely enough to find anything that tells me not to modify the bootloader or really ANYTHING about the bootloader...is total equipment protection a warranty that i could possibly void by putting olipro 2.40 on it even with the sprint official 3.35 installed?
I wouldn't worry about it. 1.06 is not the official stock bootloader either, 1.04 is, and I've swapped out my xv6800 a couple times with 1.06 on it and the Verizon stock rom. They don't usually check the bootloader. Just make sure the new Sprint stock rom is on there with radio 3.35.04 and you should be fine.
thanks much for your quick reply. i'll rest easier tonight.