my Siemens SX65 AT&T wirelles No signal - MDA, XDA, 1010 General

1. Is O2 XDA is the same models like Siemens SX65 AT&T wirelles?
http://www.pdagold.com/hardware/detail.asp?d=124
.: Extra info & Model comparison
Sold in Central Europe as O2 XDA by O2
SIM-free O2 XDA sold by Expansys
Sold in North America as Siemens SX56 by AT&T
Sold in Sweden as Qtek 1010, previously known as Joey
Sold in several countries as T-Mobile MDA by T-Mobile
2. When i download upgrade in http://www.my-xda.com/xda_soft.html and i install to my PDA Siemens SX65 AT&T, now my PDA doesn't have any signal event i change my SIM Card??
this is the name file : Radio_Stack_Upgrade_v421 and Radio_Unit_Upgrade_v31703, when i download Radio_Stack_Upgrade_v421 then after restart, my PDA is no signal, so i don't continue to install Radio_Unit_Upgrade_v31703.
Note: when i install, my sim card still plug-in.
the network only :
ST-GSM-SGP
ST-GSM1800-SGP
Globe
AIS GSM
OPTUS
AirTel
SPICE
dont have TELKOMSEL (indonesia).
Can u help me to fixed my PDA,???

What model do you have? Check the rar sticker...
PW10A are for 900/1800 MHz
PW10B are for 900/1900 MHz
Stefan

different name
LumpiStefan said:
What model do you have? Check the rar sticker...
PW10A are for 900/1800 MHz
PW10B are for 900/1900 MHz
Stefan
Click to expand...
Click to collapse
opps...thank for your advice, now i have different name in my PDA, in the sticker label is PW10B1 and in my device information Identity the model no is PW10A1... ehm? i need your advice again to fixed my siemens PDA, thank you..

gohengky said:
opps...thank for your advice, now i have different name in my PDA, in the sticker label is PW10B1 and in my device information Identity the model no is PW10A1... ehm? i need your advice again to fixed my siemens PDA, thank you..
Click to expand...
Click to collapse
Different names are no problem.
It depends on what rear sticker say. So you have a PW10B device. Tehreforen 4.xx Radio Versions do not work try the 6.xx
Also you have to ensure your provider works either on 900 or 1900 MHz....
Stefan

LumpiStefan said:
Different names are no problem.
It depends on what rear sticker say. So you have a PW10B device. Tehreforen 4.xx Radio Versions do not work try the 6.xx
Also you have to ensure your provider works either on 900 or 1900 MHz....
Stefan
Click to expand...
Click to collapse
Mr. Stefan..
i am confused.., ehm, so i must try 4.xx radio vers if doesn't work so i must try 6.xx , were i can found it?? http://www.romkitchen.de/ or where ... please help me, replace PW10A1 to PW10B1 again ..
now my device information after i change is :
bootloader V5.22
rom vers : 3.17.03 ENG
rom date : 05/15/03
radio vers : 4.21.00
Protocol vers : 32S54
Model no .: PW10A1
Platform : pocket PC
Is that correct ??
my sim card is TELKOMSEL - indonesia , GSM Dual Band (900 & 1800),
http://www.telkomsel.com/web/company_profile
Dear Mr. Stefan,
i really need advice ...
thank you.

PW10B devices require 6.xx RSU-Version. You should You should then also fix the bandwith to 900 MHz in Bootloader
http://wiki.xda-developers.com/index.php?pagename=ChangingBandsWithBootloader
RSU Version can be found on www.romkitchen.de/tools/
The displaying of PW10A in your system depends on the ROM and is complete unimportant.....
Stefan

now is fixed
LumpiStefan said:
PW10B devices require 6.xx RSU-Version. You should You should then also fix the bandwith to 900 MHz in Bootloader
http://wiki.xda-developers.com/index.php?pagename=ChangingBandsWithBootloader
RSU Version can be found on www.romkitchen.de/tools/
The displaying of PW10A in your system depends on the ROM and is complete unimportant.....
Stefan
Click to expand...
Click to collapse
Dear Mr. Stefan
Thanks for your advice, now my PDA Siemens SX65 AT&T is work again, But i am not follow your instruction..i use the other way..now i want to share my step to fixed my PDA :
1. Download Radio Unit 6.24 version, find at : http://www.yorch.net/ ---go to --- http://www.yorch.net/upgrades.htm
USA T-mobile Latest Radio Stack (Unofficial)
RU 6.24.00
2. Install RU 6.24.00 in to your PDA,put in /windows find in Windows Explorer.
3. Wait for a second, and then will search the network...
4. Success.....
my device information is PW10A1 and not PW10B1 (the label in the back pda) how come is still can work?? But,anyway its Ok,because my phone is work again..
Thank you for your advice Mr. LumpiStefan.

That is very interesting.I like it very much.where can i find it?
________________________________
Rm files

to : mukojin776
you can find at : http://www.yorch.net/ but i dont recommend you to modify your phone, if you have commitment, than do it.. and i am not & dont have responsible if your phone is death..
You can ask Mr. Lumpistefan advice if you want to upgrade or modify your phone.
Enjoy your explore...
Thank you.

How to use SX56 with Airtel(India)?

AirTel (India)? what happen with that? if your XDA (SX56) can work, so??? what do mind by that? your phone is blocked??or doesn't have signal?? can explain about that??

Related

Urgent: from iMate 1.52 to TMobile 1.60

Hi Everybody
Only one simple question: I’d like to upgrade ma i-mate 1.52 rom to t-mobile 1.60
My network is 900/1800
Will t-mobile 1.60 rom work with my network (Italy, TIM 900/1800 gsm) or tmobile rom works only with 900/1900?
Please reply asap
Regards
spanky said:
Hi Everybody
Only one simple question: I’d like to upgrade ma i-mate 1.52 rom to t-mobile 1.60
My network is 900/1800
Will t-mobile 1.60 rom work with my network (Italy, TIM 900/1800 gsm) or tmobile rom works only with 900/1900?
Click to expand...
Click to collapse
No problem, the XDA II is a tri-band phone and all ROM versions work on all bands. If the 1.60 will not install for you, you need to change the upgrade image to match the country-code of your device. We're working on a tool to do this, much like the adaptROM tool for the original XDA.
Yes, but what I have to change in t-mobile image?
Better:
I've a qtek branded XDAII. I've simply to install: RUU16006WWE_T-mobile_NL.exe and everything will works ok OR do I need to do some changes to T-Mobile files before upgrading???
spanky said:
Yes, but what I have to change in t-mobile image?
Better:
I've a qtek branded XDAII. I've simply to install: RUU16006WWE_T-mobile_NL.exe and everything will works ok OR do I need to do some changes to T-Mobile files before upgrading???
Click to expand...
Click to collapse
Watch this Topic http://forum.xda-developers.com/viewtopic.php?t=4785
I am able to go back and foward.. :shock:
I've exactly done what the post says
Replaced ms_nbf file and replaced the ones contained in update.zip file!
Can I go on without any error?
spanky said:
I've exactly done what the post says
Replaced ms_nbf file and replaced the ones contained in update.zip file!
Can I go on without any error?
Click to expand...
Click to collapse
yes you can. if you done exactly what it said to be :roll:

SX 56 and Eplus

Hi ,
i've a SX 56 (AT&T wireless) which i updated with ROM verion 3.17.03 ENG. But i have not been able to connect to the Eplus network so far. I used the bandswitch application to switch the frequency to 900/1800. Slip in a T-mobile card and it works without any issues! Has any1 been able to connect to the eplus network?! If yes (hopefully) , do let me know !
thanx
cheers
/a
What for a device you have? Take a look at the sticker back on the device... Mus be something like PW10....
Which radio version have you installed on your device? (start -> settings -> system ->device information)
not 100% sure, but i thought that the sx56 was only for the us market with 900/1900 Mhz.
900/1900 MHz has modell number PW10B with radiostack 6.x
900/1800 MHz has modell number PW10A with radiostack 4.x or 3.x
If it is a PW10A-Modell you can try entering bootloader and setting gsm to 900/1800.
if it is a PW10B-Modell you don't have any chance to get it working with Eplus.
HTH
Stefan
Hi ,
the model is PW10B1(sticker @ the back of the device) , but the device info says PW10A1 which is probably because of the rom (3.17.03 ENG)
The radiostack version is 6.12. As we speak, i m downloading a 4.x verion from your rom kitchen! but i guess i can close shop and start thinking about changing my provider ! ;-) So i guess there is no chance of changing the radio version right ?
thanx
/a
pacorama said:
Hi ,
the model is PW10B1(sticker @ the back of the device) , but the device info says PW10A1 which is probably because of the rom (3.17.03 ENG)
The radiostack version is 6.12. As we speak, i m downloading a 4.x verion from your rom kitchen! but i guess i can close shop and start thinking about changing my provider ! ;-) So i guess there is no chance of changing the radio version right ?
thanx
/a
Click to expand...
Click to collapse
Hard to say, but you're right. There is no chance of changing radio version. The limitation of 900/1900 MHz networks is a hardwareproblem, so you have no possibility (maybe some soldering) to get your device working.
The device info of the system is just a name. Depending on which rom installed it will show you PW10A or PW10B. So the sticker at the back of the device says the true....
You can only get it working with the 900 MHz providers (T-Mobile and Vodafone in Germany).
A few days ago t-mobile got an offer of the MDA I for about 30 Euro with a new contract....
So if changing the provider why not getting a new device with more memory...
HTH
PS: If you want to sell the device and you make a good price, maybe i'm interested in it....
hi stefan,
unfortunately i can't sell it coz it's my company device ! i'll just have 2 give it back and get something new!
thanx anyways
cheers
/a

NO SIGNAL

hi im using Qtek 1010 and she do not get any signal and i did use the http://lumpistefan.dyndns.org/ to flash the rom i have every think look good but still i cant have signal and im in Lebanon so please can some one provide me some help
What Device model do you have (check rear sticker)?
Which ROM version have you installed?
Which Radio Stack version installed?
What frequency do your provider use?
Stefan
HI IM USING QTEK 1010 and im beginer in this so al that i know that i just coke the ROM and im in lebanon the frequency here i think its 900/1800
soleed said:
HI IM USING QTEK 1010 and im beginer in this so al that i know that i just coke the ROM and im in lebanon the frequency here i think its 900/1800
Click to expand...
Click to collapse
Not many answesr to my questions.....
What Device model do you have (check rear sticker)? PW10A, PW10B .....
Which ROM version have you installed? Is shown on bootup or in the system itself.... Could be 3.xx.xx or 4.xx.xx
Which Radio Stack version installed? is also shown on boot up and in the system itself....
Stefan
LumpiStefan said:
soleed said:
HI IM USING QTEK 1010 and im beginer in this so al that i know that i just coke the ROM and im in lebanon the frequency here i think its 900/1800
Click to expand...
Click to collapse
Not many answesr to my questions.....
What Device model do you have (check rear sticker)? PW10A, PW10B .....
Which ROM version have you installed? Is shown on bootup or in the system itself.... Could be 3.xx.xx or 4.xx.xx
Which Radio Stack version installed? is also shown on boot up and in the system itself....
Stefan
Click to expand...
Click to collapse
ROM : 4.01.16
RADIO: 6.14
MODEL W10A
soleed said:
ROM : 4.01.16
RADIO: 6.14
MODEL W10A
Click to expand...
Click to collapse
That's curious. PW10A-models are for 900/1800 MHz and the Radio Stack 6.14 is for PW10B-models and 900/1900. Are you sure, that it is a PW10A model?
If you search manauly for a network, do you get any network?
Stefan
LumpiStefan said:
soleed said:
ROM : 4.01.16
RADIO: 6.14
MODEL W10A
Click to expand...
Click to collapse
That's curious. PW10A-models are for 900/1800 MHz and the Radio Stack 6.14 is for PW10B-models and 900/1900. Are you sure, that it is a PW10A model?
If you search manauly for a network, do you get any network?
Stefan
Click to expand...
Click to collapse
NO I DONT have any network if i search it manualy
You could try setting your band frequency manually.
Enter bootloader by holding Power button and doing a soft reset (PAy Attention, that's like a hard reset. All data on your device will get lost....)
Now pressing the right button, with the little calendar printed on it (called App1 by the device). Now the device displays:
UTILITIES
=============
DEBUG/CALI.
GSM TURN ON
GSM TURN OFF
GSM RESET
GSM 900
GSM 1900
GSM 900/1800
GSM RFCAL
GSM NORMAL
Select the correct frequency, depending on your model.
Make a soft reset to exit bootloader....
Stefan
maybe you should make a bigger warrning in your kitchen :lol:
about 900/1900 and 900/1800 radiostack picking
Rudegar said:
maybe you should make a bigger warrning in your kitchen :lol:
about 900/1900 and 900/1800 radiostack picking
Click to expand...
Click to collapse
But Radiostack is independent of the ROM....
So, what would you suggest to write as warning?
Stefan
LumpiStefan said:
You could try setting your band frequency manually.
Enter bootloader by holding Power button and doing a soft reset (PAy Attention, that's like a hard reset. All data on your device will get lost....)
Now pressing the right button, with the little calendar printed on it (called App1 by the device). Now the device displays:
UTILITIES
=============
DEBUG/CALI.
GSM TURN ON
GSM TURN OFF
GSM RESET
GSM 900
GSM 1900
GSM 900/1800
GSM RFCAL
GSM NORMAL
Select the correct frequency, depending on your model.
Make a soft reset to exit bootloader....
Stefan
Click to expand...
Click to collapse
SHE DID NOT WORK MAN SHE DID NOT ENTER TO THE BOOT LOADER

i flashed the XDA special rom - but my sx56 still locked

what to do ???
Which Radio Version is installed?
Maybe this http://wiki.xda-developers.com/index.php?pagename=Wallaby_HT_Unlock2helps you....
Stefan
i checked my radio ver:
its:
rom: 3.17.03 eng
radio: A.20.11
Protocol: 324e4
to i realy need to do the whole process in the link
i dont have sd card
thanks
one more thing
how do i know if its 900/1800 or 900/1900 version
it was at&t
I think at&t just has 900/1900 devices.....
Check the rear sticker of you´re device.
If it´s a PW10A then 900/1800, if it´s a PW10B than it´s a 900/1900.
Do not trust the output of the os....
Stefan
well, i just bought
Sd card on Ebay
and i will try this method
anyway Thanks

Help with gprs Italian WIND carrier and other problem....

Hi,
i have buy a used Siemens SX56.
Rom version: 3.17.03 Eng
Radio: 6.12
Protocol: 324e4
I have found Device information>identity tha is the model PW10A1 but in the rear of the pda is PW10B1 ?!?! What is possible?
In Setting>connection>connections>internet setting i have write my gprs parameters but i don't see the phone number!
The rom version and radio version is ok?
Thanks
Re: Help with gprs Italian WIND carrier and other problem...
klikkete said:
I have found Device information>identity tha is the model PW10A1 but in the rear of the pda is PW10B1 ?!?! What is possible?
Click to expand...
Click to collapse
Just the rear sticker is impotant. You have PW10B device.
This device is just capable of 900/1900 MHz networks.
Stefan
Re: Help with gprs Italian WIND carrier and other problem...
Ok...
can you tell me the optimal configuration for rom+radio?
What version?
Thanks
LumpiStefan said:
klikkete said:
I have found Device information>identity tha is the model PW10A1 but in the rear of the pda is PW10B1 ?!?! What is possible?
Click to expand...
Click to collapse
Just the rear sticker is impotant. You have PW10B device.
This device is just capable of 900/1900 MHz networks.
Stefan
Click to expand...
Click to collapse

Categories

Resources