I tried the following steps on my O2 Xda Mini S and after rebooting it doesn't show the SPL is 2.21.olip. It just show the original version.
Any help out there?
-connect your device
-Start hard_SPL-G4.exe
-Push the "Check DOC" button
-> The tool now checks whether your device is truly a G4, if not, it will give you an error and stops.
-> after this a dos box pops up, and it loads the softSPL to your device, to enable hard-SPL flashing.
-> then a Rom Update Utility will start, ONLY proceed if your screen is white!
-Proceed with the upgrade, it will only take a minute.
After reboot the IPL version is : 2.21.0001 and the SPL is 2.21.olip
Thanks
What is your current ROM, IPL/SPL?
Have you tried another USB port, or even another computer?
try to ugrade other rom (try the new TNT )version but take care ROM must be without ipl and spl !!!
here is link for version with ToucFlo
don't forget to use MUN's RUU
make the update on yours root drive !!! C:/ !!! i mean the update and ROM files must be on it !!!
Let the proccess going to the end and if it stops at 99% don't panic
wait and it will end and restart !!!
to mrobo and equinoxe
thanks both of you for your reply.
i haven't tried different computer(my other computer is a mac), but i have tried different usb.
Following version.
IPL 2.21.001
SPL 2.21.001
GSN 02.07.10
OS 2.21.4.1
Rom version is still the one that came with it from O2.
Do i need to do the hard_spl before upgrade the rom to one of those you told me?
Thanks .
its g3. Read damn topics
mghandour20 said:
thanks both of you for your reply.
i haven't tried different computer(my other computer is a mac), but i have tried different usb.
Following version.
IPL 2.21.001
SPL 2.21.001
GSN 02.07.10
OS 2.21.4.1
Rom version is still the one that came with it from O2.
Do i need to do the hard_spl before upgrade the rom to one of those you told me?
Thanks .
Click to expand...
Click to collapse
ignore kubek1334
Do you mean IPL 2.21.001 SPL 2.21.001 or
IPL 2.21.0001 SPL 2.21.0001?
Hello everyone.
I have a problem with my G4 from Vodafon Germany.
I woke up this morning and it was stuckd up. I did a soft reset...denn came the Bootloader and it stopped there.
The Bootloader shows:
IPL 2.21.0001
TPL 2.21.0001
I tried to flash the ROM from Vodafone Germany ROM-Version 2.21.3.1from here: http://www.vodafone.de/hilfe-support/technischer-support/97016_93771.html
It says 100% success, then Congratulations, the Phone starts up again and it is again stucked up in the Bootloader. It still shows only:
IPL 2.21.0001
TPL 2.21.0001
What should i do to get it working again?
Please HELP
Stefan
Problem solved.
I just took the Battery out for 5-10 Minutes.
It works now with the WIZ LOVE Rom.
I'll install TNT later.
bye
Hi
i have the same problem
but that battery trick wont work with my cell phone
i really dont know
but i dont have it flashed right.
because with the exe files of ruu's and more of them
he wont go furhter than 0%
it says device not detected no response, because when i launch the exe files
active sync will just lose connection.
after this i get this same bootloader problem
regards
R.G
MTTY's "wdata" cmd unlocked on SPL 2.03!Can it Unbrick the bricked ones w SPL 2.03??
I have found a way to unlock "wdata" command in bootloader 2.03!
summary:
In bricked hermeses with SPL 2.03 - NO GSM - KITL disabled, the wdata command is locked. I am not good at programing but I want to know if it possible to change the SPL(bootloader) of bricked hermeses with this command in mtty.exe??!!
How to:
1.Use the trinity splxploit -windows by pof (unbrick.bat). Let the program run for some seconds and then just close that.
2.Do not unplug the usb or soft reset the device.
3.Run mtty.exe and type "wdata" the command is unlocked!
I wanna know can we erase just the CID by erase command and write a CID value using wdata command?
If it can be done then we can unbrick our hermeses!
Yes it enable wdata, you don't need to change CID, if you can load OS.nb, then from Windows use SSPL. But real problem is how to load OS.nb via wdata
need Hermes splxploit -windows ??
i many time write in this forum who can unbrick hermes with spl 2.03 cid locked,no kitl,can not boot,stack in bootloader....only solution is that pof
or good man create Hermes splxploit -windows this will jump spl address and temporaly cid unlock Hermes then we can flash any rom.
I unbrick many Trinity bat wait solution for Hermes???
Bat wait ........and wait.
Zemo znas li ti kako da sredis brikovan hermes cid zakljucan spl 2.03...itd.
Yes, we need pof help, it will be very good to have spl exploit for hermes.
Bas nas dosta ima na XDA, mozes samo preko JTAG koliko je meni poznato ali neznam nikog ko to moze da uradi. Odakle si?
Yes, we need pof help. It will be very nice to have SPL exploit.
Mislim da moze preko JTAG, ali neznam ko to moze da uradi, odakle si?
Bad news people,
The memory layout on hermes is different than on trinity, i already looked
into this and is not possible to exploit it in the same way as I did in
trinity.
I am sorry but I have no time to invest on this now
Best Regards,
pof
Click to expand...
Click to collapse
We can wait for pof, and pray
So, we will wait.......!
I'm a prayer too
So, we will wait.......!
I'm a prayer too
Reply With Quote
Click to expand...
Click to collapse
MY HERMES IS BOOTED OS TODAY!!!
It was half dopod and half T-Mobile...
T Mobile Customanisation: Instalig Dopod stuff???
I soft reset it and it stuck again.
Booted OS
Today my hermes booted os, after soft reset it stuck again. But there is hope, right?
Can you solve No GSM with SD Card Flash?
Then Copy Hardspl V7 to the sd card and when your mobile booted into os just run that from your device.
Yes, I know that.
If you have similar problem:
1.Leave Hermes without battery for some time, hour or so.
2. DO NOT turn it on, do a HARD RESET*
*If don't work try several times
hardspl v7 or any other after 100% message image corupted
koorosh_bsboys said:
Then Copy Hardspl V7 to the sd card and when your mobile booted into os just run that from your device.
Click to expand...
Click to collapse
Yes i know this bat this will not work if hermes cid locked and stack in bootloader no kitl and gsm.Can not boot os this only work in hermes cid unlocked device then sd card work...bat what i can do when device cid locked and can not connect in activsync and everytime when try to use hardspl v7 or any other after 100% message image corupted only solution is that pof create jumpspl pach that work from dos without activesync this can help me and many other i will donate with paypal if somebody can creat this that work in hermes......
............again harmes how to unbrick 2.03
Many people try to unbrick spl 2.03 stack in boot no gsm and kitl mode and can not boot os just led light when power up...can go in bootloader bat this is all!!!.
I speak with imei-check abaout this and they told me that can repair this and it will cost 60pounds+ Here is message from imei-check.co.uk to me Hello,
You must send the device to us. The cost is 60 GBP + 15 gbp postage fee to return it back to you (or 7 GBP if we send it back to a UK address). In the day we receive it, we fix it, and next working day we send it back to you.
If you want to go ahead, please send the device + battery
(i think just need to open temporaly cid unlock in spl and this will help i mean from dos prompt,blank screen+ then flash??)and i must sent from Europe Union country .I live in Serbia and think that solution to unbrick hermes existed bat not want to tell many people......?? I will work in this now and i hope that solution will be for free when fix this.. I unbrick many hermes.artemis...etc..in Serbia bat this solution to unbrick hermes with spl 2.03 temporaly can not not have time to try?. I now will try many solution and will post here when fix this,you can trust me??....
If somebody else create solution before me please sent me message to know??
Do not post any solution from this site i try all and not work(SD card will not work when cid locked,hard spl-not work always 100% then message image corrupted,No kitl.....so please only original solution not from xda-developers..etc.
thanks for all.
Pozdrav zemljacima iz Srbije.
Pozdrav,
Ima nas prilicno sa SPL 2.03...
Igor
gsmhackerns said:
Many people try to unbrick spl 2.03 stack in boot no gsm and kitl mode and can not boot os just led light when power up...can go in bootloader bat this is all!!!.
I speak with imei-check abaout this and they told me that can repair this and it will cost 60pounds+ Here is message from imei-check.co.uk to me Hello,
You must send the device to us. The cost is 60 GBP + 15 gbp postage fee to return it back to you (or 7 GBP if we send it back to a UK address). In the day we receive it, we fix it, and next working day we send it back to you.
If you want to go ahead, please send the device + battery
(i think just need to open temporaly cid unlock in spl and this will help i mean from dos prompt,blank screen+ then flash??)and i must sent from Europe Union country .I live in Serbia and think that solution to unbrick hermes existed bat not want to tell many people......?? I will work in this now and i hope that solution will be for free when fix this.. I unbrick many hermes.artemis...etc..in Serbia bat this solution to unbrick hermes with spl 2.03 temporaly can not not have time to try?. I now will try many solution and will post here when fix this,you can trust me??....
....
Click to expand...
Click to collapse
Glad to hear that.
I am sure that the sulotion for spl 2.03 exists, but we don't know where to find it.
BTW, where is POF & olipro????
I made some progress, it stuck at OS screen now. It booted os several times today, it is strange that it can boot OS it is IPL 1.04 SPL 2.03. Stil NoGSM
koorosh_bsboys can you hermes boot OS?
Can NoGSM problem be solved with Flashing from SD Card?
igord said:
I made some progress, it stuck at OS screen now. It booted os several times today, it is strange that it can boot OS it is IPL 1.04 SPL 2.03. Stil NoGSM
koorosh_bsboys can you hermes boot OS?
Can NoGSM problem be solved with Flashing from SD Card?
Click to expand...
Click to collapse
My hermes can't boot into OS. It has stucked on 2nd splash screen (Imate telstra logo) not the OS logo!
How can u boot into OS?
If you find something new then share it with us.
My HERMES sometimes stuck at second boot scree and sometimes at windows screen, but few times it booted os. Than I put SSPL at microSD, becouse it stuck after few sec when it is on USB. OS is working ok - then I killed it again to SPL 2.03 and today get it back to working OS, No GSM.
What I did to get working OS???
1. Get battery out for about a day.
2. Put the battery in, DON'T POWER ON!!!
3. Do a HARD RESET.
If it don't work try several times.
i bricked my device back to spl 1.20 from 3.xx because the wifi and gsm antenna's didn't work after flashing it to AP 4.0! .. so i decided to flash spl back to 1.2 since my phone is X7500 . After downgrading SPL , i cannot flash to ANY ROM , HELP!!!...
http://forum.xda-developers.com/showpost.php?p=2154726&postcount=33 <<look
tried this, didn't work on my X7500
maybe you should try to flash a rom from sd-card.
download a original wm6 or wm5 rom, extract it, rename ruu_signed.nbh to ATHEIMG.nbh, copy to a fat32-formatted sd-card, insert it to your device, press and hold camera-button and softreset
please do not use a sdhc-card
bilalperwaiz said:
i bricked my device back to spl 1.20 from 3.xx because the wifi and gsm antenna's didn't work after flashing it to AP 4.0! .. so i decided to flash spl back to 1.2 since my phone is X7500 . After downgrading SPL , i cannot flash to ANY ROM , HELP!!!...
Click to expand...
Click to collapse
xacsx solution was for the lost wifi
Can you get into bootloader and what do you see?
and does any os boot up?
edit posted simultaneously with xacsx above.
My question is stillvalid
when i'm in the bootloader it shows the tricolour screen and IPL -v1.00 and SPL-v1.20 Olipro
I tried loading a ROM from the bootloader but it shows weird characters and says that this rom cannot be loaded on this device.
bilalperwaiz said:
I tried loading a ROM from the bootloader but it shows weird characters and says that this rom cannot be loaded on this device.
Click to expand...
Click to collapse
did you manage to do cmonexs mtty solution?
Have you got your athena working again?
yes i finally got my athena working!.. i realized that i wasn't running mtty as Administrator in Vista, i did that and VOILA! everythings solved, and im running AP4 now.
Hi All
Is it possible to format the DOC on a prophet as mine is stuck in bootloader and I just can't get any rom (shipped or cooked) to load it always hangs at 14% and then again at 94% and fails to load.
If I do reach the end of the flash the phone won't restart and I have to remove the battery for a while and then it goes straight back into bootloader.
So I wondered is it possible to clear the DOC and start afresh and if so how to do it.
IPL 2.20.0001
SPL 3.00.0001
OS God knows
Last rom tried to flash RUU_220734_2207114_024721_NVID
Any help would be much appreciated
Prophet DOC format
SPL should read 3.08.0001