My X01HT [email protected] first splash after upgrad to WM6
i had flashed a not completed WM6 file....
Bootloader: 1.40 Olipro....
how can i flash another firmware?
goto the unbricking thread, you should be able to reflash a ROM using the SD card method (i think)
mrvanx said:
goto the unbricking thread, you should be able to reflash a ROM using the SD card method (i think)
Click to expand...
Click to collapse
Today I got the same problem after flash a custom ROM with incorrect INITFLASHFILES.DAT.
It's not neccesary to flash from SD. Enter into Bootloader mode (tricolor screen), conect to the PC (active sync will not catch the device) and run RUUwrapper selectign 1.40+Is hard SPL to flash another nbh ROM file.
i had already unbirk it....
Related
I by mistake flashed Rom 1.94.710.2 using SD Card, The SPL got overwritten and I am stuck with the boot loader and unable to flash any rom, Error 294.
Also not able to flash using SD card.
Any help is appreciated.
Thank you and best regards
how did the hardSPL get overwritten? I'm new to HTC hacking but isnt that supposed to be impossible?
Try to go into SPL and flash using USB. May be that works. Not sure even
try to download ship rom &flash throught USB cable
how to install radio through usb and card? currently bad rom is installed on my hd2
which is stuck on startup.so want install radio.i got a nbh file.so shoud i put file in card and rename leoimg.nbh or volume down boot and via usb?
dont want again brick my hd2
but there is HSPL.
yousufshah said:
how to install radio through usb and card? currently bad rom is installed on my hd2
which is stuck on startup.so want install radio.i got a nbh file.so shoud i put file in card and rename leoimg.nbh or volume down boot and via usb?
dont want again brick my hd2
but there is HSPL.
Click to expand...
Click to collapse
Firstly you have to have HSPL installed.
You can flash it via sd by putting the radio file into the root of sd card but don't forget to rename it leoimg.nbh. Don't flash radio 2.xx.51.xx if you have Tmous. It will brick ur phone.
You can also flashing it via USB but you need RUU (flashing tools).
Either way you have to be able to go into boot loader mode by way of press vol down and power on buttons at the same time.
Cheers
Hi guys im going back to wm 6.5 from android, how would i go about flashing these roms(energy). I have Hspl 2.0, magldr 1.13 and cmw installed. Do i just do it via hspl or do i need a rom manager?
Fasty12 said:
Hi guys im going back to wm 6.5 from android, how would i go about flashing these roms(energy). I have Hspl 2.0, magldr 1.13 and cmw installed. Do i just do it via hspl or do i need a rom manager?
Click to expand...
Click to collapse
The easiest way is via SD Card method.
If your coming from android then you already have an appropriate radio and HSPL installed.
(You can ceck this by entering bootloader, hold vol. on whilst turning the phone on)
To flash a new WM6.5 rom;
Enter Bootloader (vol down + power)
Connect via USB...
Wait for the word "serial" on the bootloader screen to change to "USB"...
Unzip the energy rom and place it in a folder with the custom ruu provided...
Run the custom RUU provided with the energy rom you downloaded...
Wait...
Phone should reboot once flash is complete......
Flashing a 6.5 ROM will remove MAGLDR from your phone.
Make sure you do backups in android in case you want to go back.
Forget about CMW and rom manager.... they are android only.
Hope that helps.
If your coming from android then you already have an appropriate radio and HSPL installed.
(You can ceck this by entering bootloader, hold vol. on whilst turning the phone on)
To flash a new WM6.5 rom;
Enter Bootloader (vol down + power)
Connect via USB...
Wait for the word "serial" on the bootloader screen to change to "USB"...
Unzip the energy rom and place it in a folder with the custom ruu provided...
Run the custom RUU provided with the energy rom you downloaded...
Click to expand...
Click to collapse
i stuck in this step.. it says Error Updating Try Again
my hd2 bricked after updating to official rom
Mr.Cobbra said:
i stuck in this step.. it says Error Updating Try Again
Click to expand...
Click to collapse
i have a big problem with my hd2 usb port was broke not recognizing by any cable usb,i tried to flash official rom via sd card then update error appear what can i do
Is it possible to install wm 6.5 via MAGLDR using USB Flasher?? As now I'm in the situation when I can't enter bootloader (for some reason its not working), I also can't install via mem card as my Clockwork recovery is also not working. Thanks
Sw1pe said:
Is it possible to install wm 6.5 via MAGLDR using USB Flasher?? As now I'm in the situation when I can't enter bootloader (for some reason its not working),
Click to expand...
Click to collapse
No bootloader only.
I also can't install via mem card as my Clockwork recovery is also not working. Thanks
Click to expand...
Click to collapse
again, you need to enter botoloader to flash winmo from sd card, not clockwork. If you cant get into bootloader at all, you can't flash winmo.
I'd have a play with the 'nand toolkit', , perhaps reinstalling magldr will unblock the bootloader.
i don't know if i can save my x7500, i can only get the bootloader screen my spl is 3.05 the device is also cid locked so i can't flash any custom rom, what are your suggestions? any of u heard about goldCard? can any flash a rom with spl 3.05? what were you do if u have the same situation?
Thanks...