Related
I extracted the radio version 1.20.31.10 from the imate jasjam 1.31.305.2 rom using Asukal's method.
You can find the radio upgrade only and upgrading instructions on the Hermes Extracted Radio ROMs wiki page.
Remember:
- screen will show "Upgrade Radio Stack Please wait........."
- after finishing flashing radio you will see an "Upgrade Error", but the radio ROM will be flashed anyway
- no need to hard reset after upgrading the radio, only soft reset with stylus when upgrade ends.
- upgrade at your own risk, i take no responsiblity for anything that happens to you, your Hermes, your marriage, etc.
This sucks...I followed the directions to the letter and now I'm stuck on the windows mobile screen.
It seems that when it soft-rest, right above the D1.18 (on the bottom center on the screen) NO GSM appears for a few seconds then disappears.
i have exactly the same problem, it just sits at the windows mobile screen.
i am going to do a hard reset to see if that helps
too bad :/ I was just about to upgrade my radio rom with that.. thx for the notice.
Hard-rest doesn't help. I think the issue is NO GSM...the phone doesn't know what to do. And, not being able to activesync, I can't do anything else.
Had the same problem.
Put the device in Boottloader mode (left OK & Power & reset), and loaded Radio 1.16.
Workes !
Probably something went wrong during extracting 1.20 Radio.
oops... sorry guys, i will remove the upgrade inmediately... it worked on my hermes, will try to flash an older rom an try it again! Those who are stuck on windows mobile screen do what torklemm says: flash radio 1.16
That's what I'm trying to do now, I just hope it works.
Thanks.
EDIT: Can't seem to get it to see the phone via activesync. Unable to flash anything at this point.
I am going to give that a try now, will update with the results
Bacco said:
EDIT: Can't seem to get it to see the phone via activesync. Unable to flash anything at this point.
Click to expand...
Click to collapse
You do not need activesync, disable activesync usb connections, put the device in bootloader mode and start the flash utility (ma_upgrade_noid) from 1.16 radio upgrade.
pof said:
You do not need activesync, disable activesync usb connections, put the device in bootloader mode and start the flash utility (ma_upgrade_noid) from 1.16 radio upgrade.
Click to expand...
Click to collapse
Tried that pof, all is get is "checking the info on your device and don't disconnect, etc" and nothing more. A few minutes later it shows the screen detailing the PPC radio and ROM versions and the radio version that I'm trying to install, but everything is blank. I say yes anyway and it just sits on the "checking the info on your device and don't disconnect, etc" screen forever.
That's why I thought something wasn't right w/o activesync. I'll try again.
EDIT, again: I'm now trying the Cingular 1.13 radio...that seems to be installing. Pray for me guys
EDIT 2: Yeah, I get the same error as you shark1
I get an error stating this utility is not design for this device please get the correct update utility
i have the same problem On boot i see "NO GSM". Now my tytn doesn't boot and also when i try to reload 1.16 radio it stucks... I'll try with 1.13...
1.13 don't go it say it's not designed for my device... o__O
now i'll try 1.11 same problem...
I'm uploading a "hopefully" fixed version on ftp (again, it worked on my hermes from 1.16 to 1.20), do not download it yet until I finish uploading... (17% now) i will edit this post and let you know when it is finished.
EDIT: Upload finished!
POF: OK i will wait, hopefully that will work, at present I will try 1.11 as others are trying 1.13
I get the same update error with 1.11
I have try to find my old phone, so I can make calls
Ok, now I'm totally confused. In bootloader, I don't see USB on the bottom anylonger. if I unplug my USB cable, I see serial...but I can't seem to do anything to get USB recognized again.
Why did I do this???
EDIT: Rebooted everything!
Hi all,
got the same problem. Phone in bootloader and can't go back to 1.16 or lower..... hope the new 1.20 will work
rmaat said:
Hi all,
got the same problem. Phone in bootloader and can't go back to 1.16 or lower..... hope the new 1.20 will work
Click to expand...
Click to collapse
i hope to... or i think that our only way is c.a.
pof said:
I'm uploading a "hopefully" fixed version on ftp (again, it worked on my hermes from 1.16 to 1.20), do not download it yet until I finish uploading... (17% now) i will edit this post and let you know when it is finished.
EDIT: Upload finished!
Click to expand...
Click to collapse
pof, please clear the not yet
also this radio have the same problem; not designed for this device... and now?
Hy at all,
I have one MSPV M3100 and i upgrate this to WM6 Xda-Live 0.20.1 ROM. This rom woek perfectly but my telephone run very bad.
Y have this version:
ROM: WM6 Xda-Live 0.20.1
Radio ROM: 1.16.0.0
Bootloader: SPL 1.06
I want upgrade my Radio Rom to 1.27 version, but not it with himself. I have tried 4 times, and always the same error. ERROR 114= Upgrade error.
I have followed these instructions:
Upgrade instructions
1. Extract the contents of the compressed file you've just downloaded
2.Run MaUpgradeUt_noID.exe
Description for Radio 1.11 shows ver 0.70, but don't worry about it, it is really 1.11
3. The Hermes screen will turn white and show "Upgrade Radio Stack Please wait........."
4. If you get a "ERROR 120: COUNTRY ID ERROR", do not disconnect the device, run MaUpgradeUt_noID again.
5. The upgrading process will start and MaUpgradeUt_noID.exe will end up saying "ERROR 114: Upgrade Error", but the radio ROM will be flashed anyway, don't worry about that error!
6. Soft reset with stylus (Device will not be hard reset and no data will be lost)
that I have done badly?
as I have it to do?
Sorry for my english, is very bad.
Thanks a lot of for your answers.
By.
You need to prep the bootloader. I will go find the link.
Here is the wiki link. This should get you started. I am in the process of downgrading from 1.35 to 1.27 right now. lol
I have the Oliman 1.10 and ipl is 1.01. Search for hard spl and you will have it all.
http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms
Before you flash the radio it is a good idea to use Hard-SPL so if the flash goes wrong the phone can be recovered.
pardon, but what is Hard SPL??
Is a program??
how I prepare the bootloader??
thanks
You Need to use SSPL. Look for Radio Files with SSPL in the WIKI.
Hello,
I must make downgrade to a ROM with the version SPL 1.04 to be able to
change to my radius ROM?
That is what me say?
Thanks.
@merodio How is it that you live in the USA, but have a CANADIAN cell provider (Fido), and also can't speak/write English (again, since you live in the USA)???
EDIT: Apparently the fido icon comes up when you select "Albania - Albanian Mobile Comms" as your provider.. Which is ALSO a non-sensical choice if you're in the USA....
You need to be superCID to run the RUU you're trying to use. Use one that uses SSPL.
LegolasTheElf said:
@merodio How is it that you live in the USA, but have a CANADIAN cell provider (Fido), and also can't speak/write English (again, since you live in the USA)???
EDIT: Apparently the fido icon comes up when you select "Albania - Albanian Mobile Comms" as your provider.. Which is ALSO a non-sensical choice if you're in the USA....
You need to be superCID to run the RUU you're trying to use. Use one that uses SSPL.
Click to expand...
Click to collapse
Hello,
Pardon. It does not form well my profile. I have two mobile. One Hp 6815 with Movistar and one SPV M3100 with Orange.
Pardons but I do not understand.
How I can obtain superCID?
I want to put the RADIO ROM 1.27.0.0 SSPL that this here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms
What I must do first?
Downgrade to a ROM with SPL 1.04 or Change to SuperCID.
Thanks for reply.
By.
Hey Meodio_99, sorry but you are a classical case of someone who is going to end up with a bricked (dead) phone. You have a disadvantage as your English does not appear to be very good but you need to both read AND understand otherwise sooner or later you will end up with a bricked phone.
I suggest you read all the WIKI sections talking about upgrading and also http://forum.xda-developers.com/showthread.php?t=296722 and http://forum.xda-developers.com/showthread.php?t=286755
It might take you an hour or so but it might also prevent you from crying yourself to sleep at night because you killed your Hermes!
Just got Hermes vodafone with German language and successfully loaded hardspl and have it in supercid. Now i want to upgrade to english version, but i keep getting error 260. PDA stays in RGB mode and saying USB. If i disconnect the cable it switches to Serial.
I have tried to update with
vodafone 1.20.161.6 aku 2.3
vodafone 2.07.161.1 aku 3.3
htc 1.35.255.102 aku 2.3
they all report the same. Have tried rebooting computer as said in wiki, but no success.
i now use original
HERM200
ROM 1.20.126.3
RADIO 1.16.00.0
any idea?
Thanks
Are you sure it is a supercid? Write the SPL, can you boot os?
Yes, i can boot os fine.
SPL-1.40.Olipro
IPL-1.01
I did supercid procedure with success....at least i thoughts so. It's my fist upgrade, so anything is possible. I used HTC Hermes SIM & CID Unlock - v3a
Thanks
I have the same problem with my second-hand JASJAM. The only way I can flash ROMs on my phone is by using RUUWrapper and select force SSPL and this always works well.
COME ON people!!!
A simple search would have remedied this...its been a topic so many times now!
The reason the official RUUs wont work correctly is because of the fact that HardSPL has been loaded, hence the SPL version isnt recognised, you gotta flash the official .nbh file using CustomRUU.
But first update to the latest version of HardSPL (see the sticky thread).
When you run the customRUU program select your SPL version (or use autodetect) and off you go!.
EDIT:: to get you started, Hardspl is HERE.....flash it.
then open the RUU with winzip or winrar and copy over the .nbh file into a folder.
download CUSTOMRUU.....run it from that folder with your device synced over activesync....select your SPL and voila.
Silly fella's. Its alright though I used to make the same mistake. I think im better friends with the search feature on here than I am with my real friends. You can always rely on the the WIKI or the search.
Thanks for help mrvanx i manage to flash with no problems now.
Promise to read more wiki next time
My problem was the same described in this post (too recent SPL).
I similar problem only difference is now phone wont go out of boot mode as its not recognised by active syn or in the rom update procedure.
Please help urgently cannot restore phone...and i dont know how
If you have Hard SPl V7 installed, try to re-install the rom, or a different one using the sd card method.
1. Format 2Gb or less sd card FAT32 and copy .nbh file onto it. Rename to hermimg.nbh .
2. Insert into Hermies and reset into bootloader, hold power, OK button under flywheel and reset with stylus hold all buttons in until you get to tri-colour (bootloader) screen.
3. Follow onscreen instructions...
Cheers...
I Have read allot of data, unbrick tutorials and upgrades suggestions...
but I Still haven't found what is the correct upgrade stages.
As far as I have read from the unbrick suggestions, I've reached to the following order:
1) Upgrading SPL (Enabling KITL)
2) Unlocking
3) Upgrading radio
4) Upgrading Windows
Can someone confirm or recommend/add other steps ?
During the upgrade steps, will the HERMES be usable ?
Unlock first THEN hard spl.
DONT mess with your radio if it works fine, as this is part that can COMPLETELY brick your phone(you may be able to use as a PDA but not gonna be a phone EVER again.)
Load an os(either a stock one OR one of the cooked roms our TOP chefs cook up.), most come as OS only, no radio.
Hope this helps.... Cheers
It is useless for me, I cannot unlock the phone, due to different locking technique.
there are few posts about a locked Jasjam, with no olutions.
all the unlocking process went well, 3 times...
after the unlock process, when I insert the sim, it connects to the network, (indicated with 5 lines) and after about 5 seconds, it disconnect and says :
"The system detected an invalid SIM card"
and asks for unlock code.
now I have the following versions:
IPL 1.01
SPL 1.40.Olipro
Radio 1.16
any ideas ?
The Solution
To unlock Cellcom (Israel) JASJAM, As weird as it sounds, you should disable/deactivate/uninstall/whatever the EYRON Multi language support, which comes pre-installed.
I'll let the experts explain it.
I Dont know if it works for Orange-il Tytn too.
please consider note this in unlock guide ?
Now, which version of HARD-SPL with KITL should I Install... (Link will be helpful)
Please note that I Only Unlock the SIM, and not SuperCID, the .BAT file of the unlocker says:
"CID Unlock: will make your phone SuperCID forever, don't check this if you are unsure. HardSPL will do same effect without loosing warranty."
Olipro ver 7(Hard SPL) This is considered the best for the layman, if you want to develope roms/ programs then you should use ver 9. However, ver. 9 does throw up an error after flashing. There is no problem and olipro said he'd get around to fixing it, BUT.......
Hope this helps...
ultramag69 said:
Olipro ver 7(Hard SPL) This is considered the best for the layman, if you want to develope roms/ programs then you should use ver 9. However, ver. 9 does throw up an error after flashing. There is no problem and olipro said he'd get around to fixing it, BUT.......
Hope this helps...
Click to expand...
Click to collapse
I have upgraded to Olipro V7
When I Boot into bootloader, I see:
IPL-1.04
SPL-2.10.Olipro
But I Still not get any sign of KITL according to this threat (Step 5).
The Device is booting normally, as if I'm not holding any bottons.
How can I check if KITL enabled ?
Do I need KITL while using OLIPRO V7 ?
Orenk,
Have you read the Mr Vanx guides or the wiki? Here are the links:
http://www.mrvanx.org/cms/
http://wiki.xda-developers.com/
WB
I need your help
My tytn is bricked
The Bootloader shows me HERM200 IPL-1.01 (White font, Red line)
HERM200 MFG SPL-1.01 (Yellow font) Redline)
I cant connect with my active sync anymore
The OS do not boot anymore
It shows my "no gsm"
It freezed by Windows Mobile Screen !
What can i do ?
Can anybody repair it ?
My english ist so bad, i come from Germany. SRY
I hope anybody can help me
Freeheld
press these buttons together: side ok button, power button and reset button,
then the HTC will go in USB mode and use some rom to flash it
thx for ur answer
when i try to flash it says me Error connecting
actice sync doesnt find my Tytn no conection
the tytn goes to the grey flash screen and interrupt it
can anybody tell my the right ROMs ?
i need a german roms and german radio rom
i have found my bricked Type
SPL HTC_BOOT Boot OS? No GSM? KITL
1.01MFG <=0107 No Yes ---
Diagnostic
bricked while flashing radio
Solution
Flash any type2 radio in NBF format, run RUU 2 times. If that doesn’t work, flash the radio using HERMflasher
i cant find "type2 radio roms in NBF format"
How i can see my HTC_BOOT ?
I crashed my tytn so hard
A new problem
Microsoft ActiveSync cannot recognize this device for one reason:
*The device was not connected properly.
.
.
.
And so one
How i can flash an new right ROM ?
You can flash from the SD-Card:
http://wiki.xda-developers.com/index.php?pagename=Hermes_SDCardFlashing
Here are the radio ROMs:
http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms
Thx but it doenst worked
i get an error
Loading...
than cant find file
but i renamed it write ???
how i can see that i have hardSPL
i dont beleave that i have it
and i cant install it because my activsync doenst work
If you're using XP - untick "Allow USB Connections" in activesync on pc. Put Hermes into bootloader and run the flash for Hard SPL V7. If this works then try an sd card flash for a different rom. No guarantees it will work but at this point, what have you got to loose?
Good Luck...
it doesnt work very well
i get an UPDATE ERROR
hmmmm
active sync is unticked (USB)
i have found a problem
i had flasched the bootloader 1.01MFG without SuperCID now i get Level= FF in mtty.exe, so i can flash back to 1.04 to install HARD SPL
How can i come back to 1.04 ?