I need your help
My tytn is bricked
The Bootloader shows me HERM200 IPL-1.01 (White font, Red line)
HERM200 MFG SPL-1.01 (Yellow font) Redline)
I cant connect with my active sync anymore
The OS do not boot anymore
It shows my "no gsm"
It freezed by Windows Mobile Screen !
What can i do ?
Can anybody repair it ?
My english ist so bad, i come from Germany. SRY
I hope anybody can help me
Freeheld
press these buttons together: side ok button, power button and reset button,
then the HTC will go in USB mode and use some rom to flash it
thx for ur answer
when i try to flash it says me Error connecting
actice sync doesnt find my Tytn no conection
the tytn goes to the grey flash screen and interrupt it
can anybody tell my the right ROMs ?
i need a german roms and german radio rom
i have found my bricked Type
SPL HTC_BOOT Boot OS? No GSM? KITL
1.01MFG <=0107 No Yes ---
Diagnostic
bricked while flashing radio
Solution
Flash any type2 radio in NBF format, run RUU 2 times. If that doesn’t work, flash the radio using HERMflasher
i cant find "type2 radio roms in NBF format"
How i can see my HTC_BOOT ?
I crashed my tytn so hard
A new problem
Microsoft ActiveSync cannot recognize this device for one reason:
*The device was not connected properly.
.
.
.
And so one
How i can flash an new right ROM ?
You can flash from the SD-Card:
http://wiki.xda-developers.com/index.php?pagename=Hermes_SDCardFlashing
Here are the radio ROMs:
http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms
Thx but it doenst worked
i get an error
Loading...
than cant find file
but i renamed it write ???
how i can see that i have hardSPL
i dont beleave that i have it
and i cant install it because my activsync doenst work
If you're using XP - untick "Allow USB Connections" in activesync on pc. Put Hermes into bootloader and run the flash for Hard SPL V7. If this works then try an sd card flash for a different rom. No guarantees it will work but at this point, what have you got to loose?
Good Luck...
it doesnt work very well
i get an UPDATE ERROR
hmmmm
active sync is unticked (USB)
i have found a problem
i had flasched the bootloader 1.01MFG without SuperCID now i get Level= FF in mtty.exe, so i can flash back to 1.04 to install HARD SPL
How can i come back to 1.04 ?
Related
Hi i'm newbie
I'm french thus excuse me for my english
I try to upgrade my htc in WM6, i sucess, no problem.
After i upgrade with a rom radio and the upgrade block at 40 %.
Now the phone boot in tricolor mode.
IPL-1.04
SPL-2.10.Olipro
I find in the forum that for unbricked my htc i must to flash any rom in nbh format.
How to do that.
I try to install also original ROM_9600_FRA_10303.exe rom but activsync it not active.
Someone can help me please
thanks
Connect you device in bootloader screen with your PC with USB and you should see USB appear at the bottom of the screen on yor device. Now flash any .nbh with the RUU wrapper and select SPL 2.10 New bootloader and flash the ROM...
what is the RUU Wrapper, where can i download it?
unikgwada said:
what is the RUU Wrapper, where can i download it?
Click to expand...
Click to collapse
Here it is
RUU wrapper is a software?
Explain me which is it
unikgwada said:
RUU wrapper is a software?
Explain me which is it
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=298737
when i use RUUWrapper i havbe an error [260].
What i can do
In the tri color screen with the device plugged in via USB do you have USB written at the bottom? Does your device appear in the device manager?
Yes USB is written on the bottom, and yes the phone appear in device manager .
What are you using XP or vista?? You could try a different USB port or if that doesn´t work you may have to roll back the driver... read this http://forum.xda-developers.com/showthread.php?t=299657
I'm using XP.
When i use myyt.exe the phone make something, but when i try to upgrade any rom i have always this message error [260]
i try to update with rom radio 1.47.00.10 , the upgrade is correct 100%
but when i reboot i return in tricolor mode
I success to install rom with UUwrapper but now the phone block on the picture windows mobile
Thanks
i fine a the solution
Could you please share the solution ? I've got a similar case, thanks.
Just got Hermes vodafone with German language and successfully loaded hardspl and have it in supercid. Now i want to upgrade to english version, but i keep getting error 260. PDA stays in RGB mode and saying USB. If i disconnect the cable it switches to Serial.
I have tried to update with
vodafone 1.20.161.6 aku 2.3
vodafone 2.07.161.1 aku 3.3
htc 1.35.255.102 aku 2.3
they all report the same. Have tried rebooting computer as said in wiki, but no success.
i now use original
HERM200
ROM 1.20.126.3
RADIO 1.16.00.0
any idea?
Thanks
Are you sure it is a supercid? Write the SPL, can you boot os?
Yes, i can boot os fine.
SPL-1.40.Olipro
IPL-1.01
I did supercid procedure with success....at least i thoughts so. It's my fist upgrade, so anything is possible. I used HTC Hermes SIM & CID Unlock - v3a
Thanks
I have the same problem with my second-hand JASJAM. The only way I can flash ROMs on my phone is by using RUUWrapper and select force SSPL and this always works well.
COME ON people!!!
A simple search would have remedied this...its been a topic so many times now!
The reason the official RUUs wont work correctly is because of the fact that HardSPL has been loaded, hence the SPL version isnt recognised, you gotta flash the official .nbh file using CustomRUU.
But first update to the latest version of HardSPL (see the sticky thread).
When you run the customRUU program select your SPL version (or use autodetect) and off you go!.
EDIT:: to get you started, Hardspl is HERE.....flash it.
then open the RUU with winzip or winrar and copy over the .nbh file into a folder.
download CUSTOMRUU.....run it from that folder with your device synced over activesync....select your SPL and voila.
Silly fella's. Its alright though I used to make the same mistake. I think im better friends with the search feature on here than I am with my real friends. You can always rely on the the WIKI or the search.
Thanks for help mrvanx i manage to flash with no problems now.
Promise to read more wiki next time
My problem was the same described in this post (too recent SPL).
I similar problem only difference is now phone wont go out of boot mode as its not recognised by active syn or in the rom update procedure.
Please help urgently cannot restore phone...and i dont know how
If you have Hard SPl V7 installed, try to re-install the rom, or a different one using the sd card method.
1. Format 2Gb or less sd card FAT32 and copy .nbh file onto it. Rename to hermimg.nbh .
2. Insert into Hermies and reset into bootloader, hold power, OK button under flywheel and reset with stylus hold all buttons in until you get to tri-colour (bootloader) screen.
3. Follow onscreen instructions...
Cheers...
Hey friens and developers,
I have read the information in post " dead hermes? corrupted radio? Post comments here" and follow the instruction "Device is stuck in bootloader mode".
My problem is, I can´t get a connection to my device (mtty), I have on 4 different PCs (XP or Vista Operation System) every time the same information --> "USB Port can´t not open".
My Question is, is the Bootloader damage ?
History:
The hermes are function well and I get yesterday a problem with frozen the Device. I solve the problem and do a hard reset, but after Installation the Device boot and stay now in the HTC Screen. (Look attachment). If i hardreset the device a see the tri-color Boot-Picture for a 0,5 sec, but no numbers.
THX for some idea´s
Thomas
Did you read the Wiki page for unbricking the Hermes?
http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
Yes I do, but I have the Problem with the USB Connection (mtty). You have any Idea for the USB Problem?
The Hermes now is function with USB. I install a new XP with SP2 on my PC and I have a connection.
Now I see the BOOTLOADER
HERM200
IPL-1.04
Herm200
SPL 2.-03
I want to flash the Device, but every Solution STOPT by 1%, "the image file is corrupted". Any Idea how to change the Bootloader to a compatibility Bootloader over mtty?
What ROM you trying to flash? It has to be a Hermes ROM or you're gonna end up with a permanent brick.
Have you installed Hard SPL V7? If you have you can use the sd card method to install the ROM.
If its a Hermes ROM and you keep getting the "the image file is corrupted" message, good, it means you won't have a brick at the end as the file is corrupted and could result in a brick. Either download the ROM image again or download something else. That error message is there to save your Hermes from brickage.
Cheers...
When i tried to install any firmware the progress stop at 11% and the Hermes only turn on in bootmode, any idea??
rmorera84 said:
When i tried to install any firmware the progress stop at 11% and the Hermes only turn on in bootmode, any idea??
Click to expand...
Click to collapse
I had that problem and few more with my Hermes.
While it didn't help me, this suggestion by ultramag69 may help you...
Use the sd card method to flash a new rom, instead of a USB cable/Windows computer.
1. Format a 2Gb or less sd card to FAT32, copy the large 50MB-90MB .nbh file onto it and rename to hermimg.nbh
2. Insert the card into your Hermes and reset to bootloader (hold OK & POWER and push RESET for a sec with the stylus)
3. If you haven't stuffed up the other steps, follow the prompts.
Hope this helps!
Just one other thing summoner, make sure you have Hard SPL V7 installed. Otherwise the ONLY rom I'd try flashing like that is the SHIPPED STOCK ROM. Its so the CID will be recognised and won't cause a brick.
rmorera84, unless you've installed Hard SPL V7 then find the SHIPPED STOCK ROM and flash that, anything else may permanently brick your Hermes.
If you have Hard SPL V7 (IPL 1.04, SPL 2.10 oli) then flash what you like...
Cheers...
- Installed latested Orange rom, that I know of - SPV_M3100_ROMUpdate_1007
- installed Hard SPL 7 & applied SIM unlock/super CID
- re-installed TNT TNT.19199_Professional_Hermes
The result is:
IPL-1.01
SPL-1.40.Olipro
I suppose I should upgrading the radio rom now!?
I am told don't try fixing what isn't broken - and it is working. 3G iNet, Phone, WiFi, BT - all good atm.
Or is there a particular update I should still install?
Thanks!
SUMM0NER, you're using an older, not so safe version of Hard SPL. The Hermes is downgraded to SPL 1.40 when you sim/CID unlock your phone. Best idea would be to re-install Hard SPL V7. Its a later version that seems less prone to problems when flashing.
Go back to the Hard SPL thread and get Hard SPL V7. I had the same thing happen to me when I unlocked the Hermes, nearly cost me my handset.
The steps are unlock Hermes, Install Hard SPL then upgrade OS.
Cheers...
Do I need to re-apply the OS rom file?
I just reinstalled Hard SPL7, now shows as IPL-104, SPL-2.10.Olipro.
Thanks!
My hermes only work whit this rom:Schaps_WM6Pro_ESN_3.54b-0808_Full
Because whit any other rom they stuck at 11%.
This is the info or the phone:
IPL-1.01
Spl-1.40.Olipro
Whit the first rom the htc boot but the phone funtion don´t work.
rmorera84, refer to my last post.
SUMM0NER, no. You have loaded the os, the reason you put Hard SPL V7 is if you want to upgrade the radio rom (not a good idea unless you are experiencing problems) or wish to change the os. Just means recovery is easier than if you didn't have it.
Cheers...
Many thanks ultramag69.
rmorera84 what branding is your Hermes (ie: Orange M3100, T-Mobile Vario 2, Vodeaphone V1605 etc...)?
Can I assume your Hermes is working right now?
If it is download and install HardSPL V.7 (attached to the bottom of the first post!)
Ones done verify that it installed correctly by holding the OK & Power button and pushing reset for a sec. The screen should display the coloured bars and say towards the centre: SPL-2.10.Olipro
It´s Cingular 8525, i could install the HardSPL V.7, now what rom i can flash??
You didn't confirm if it is working right now!?
If it is not working, try one of the official WM5 Cingular roms from this list. If that worked apply HardSPL 7 and take it from there.
Ones you downloaded the Cingular rom update you will have to keep unpacking the .exe files until you come to the actual .NBH file (WinRAR works for me).
Then follow ultramag69's instructions on flashing the rom via memory card.
Works, now i have this info:
HERM100
IPL-1.04
HERM100
SPL-2.10.Olipro
I download the official Cingular WM5 rom, but. i don´t know how install this rom by memory card, could you help me??
Excellent!
Try downgrading to the Cingular rom via USB. Just double click the EXE and follow the instructions.
To use the memory card method follow these steps...
0. unpack the .exe file containing the rom with Winrar (right-click exe then choose "Extract to...\")
1. Format a 2Gb or less sd card to FAT32, copy the large 50MB-90MB .nbh file onto it and rename to hermimg.nbh
2. Insert the card into your Hermes and reset to bootloader (hold OK & POWER and push RESET for a sec with the stylus)
3. If you haven't stuffed up the other steps, follow the prompts.
The reason to use the memory card to upgrade a rom, rather than a usb cable, is to cut down on failed upgrades (dodgy Windows/usb port/usb cable/etc..).
All working? Try upgrading to a Hermes rom that didn't work previously.
Any rom you can find in the Hermes section. Go to the WM06 part of the forum, theres a sticky at the top with about 50 older roms and you'll find other roms there too (latest is wm6.5).
Cheers...
i install the official WM5 AT-T version the WM6 AT-T, but, i still whit the no-gsm problem, can i flash i radio? or what i can do??
You may not be able to fix this, if you know what the original SHIPPED STOCK ROM was and can find it, then flash that. It may not work, if it gets stuck at 11% - 17% mark it means the radio ROM is stuffed and the memory area is corrupted. Not fixable.
You could also try, if you know what it is, the original radio rom by itself. Again, if you can't get it to work, you have a PDA but won't work as a phone ever again. Sorry to be the bearer of bad news.
Im to having the same problem, it keeps going back to the 2.1.Olipro boot loader.
I tried the memory card option and it starts to install but then stops.
Does anyone have and sugestions?
Cheers
Help Help
Hi, I got my Hermes 8525 in boot mode what i did is to install this Schaps_WM6Pro_WWE_4.00_Full.exe now my hermes is working but i want to unlock it..what can I do cos everytime i try got in to boot mode again..any help tks.,..
Hi, I was unlocking my htc 8525 at&t but i was using vista and my cell keep in Type 2a: When the phone boots, it goes directly to bootloader mode (tri-color screen)
what can I do to fix it... tks
Whats the info for your SPL?
Hi, I got my Hermes 8525 in boot mode what i did is to install this Schaps_WM6Pro_WWE_4.00_Full.exe now my hermes is working but i want to unlock it..what can I do cos everytime i try got in to boot mode again..any help tks.,..
SPL- 1.40
Try unlocking it with Windows XP
hi, i tried in win xp but keep the same in boot mode...
On the PC, in activesync settings, untick "Allow USB Connection".
Put Hermes into bootloader (tri-colour screen) and then run the RUU_Wrapper.exe file of the unlocker program. Follow all the instructions to unlock your Hermes and once its unlocked put Hard SPL V7 on it BEFORE flashing any thing else. After flashing Hard SPL V7, go back to bootloader and check SPL is 2.10 oli.
You now have a Hermes that is easier to recover if somehing goes wrong with a flash, excluding radio rom flashes.
Cheers...
Hi, canu put the link of the program u told me to use..tks for your help..
RUU_Wrapper.exe, Its included in any rom you want to flash. Its how you flash using the PC...
Hard SPL is in the sticky of the Hard SPl thread in upgrading section.