Vario 2 won't flash after Unlocker3a - 8525, TyTN, MDA Vario II, JasJam Software Upgradin

Hey there,
got a "new" device by T-Mob and wanted to unlock it again. So I did, and unlocking worked so far. Now I want to flash the original shipped Rom by T-Mob Germany, but this doesn't work. Device changes to bootloader and than the computer tells me to check the cable. Tried to flash the rom with changing to bootloader and than start flashing, too, but same error. I tried to flash the unlocker-radio-rom again and that works.
Now I need a solution to flash original T-Mob shipped (WM5).
Any ideas?
Update: Flashing with Custom RUU and the nbh-file from original Rom works. But still no 'normal' flashing possible.
Is it possible to set back SPL 1.04 instead of 1.40.Olipro (by the way nice work Olipro, but not for warranty-reasons )

No idea anybody?

This issue has been documented to DEAT, the reason a standard RUU program doesnt work correctly is because there is a modified (and FAR SUPERIOR) bootloader on the device and the RUU doesnt understand what it is.
CustomRUU can detect it because olipro has built the support for the different SPL versions into it.
It is highly recommended that you update to HardSPLv7 (SPL version 2.10.olipro) as this protects your device against a load of possible ways to really damage your device.
By following the guides i have compiled on "how to safely flash WM5" and the various downgrade/upgrade guides on my site you might see how much better CustomRUU and nbh editting is.....also i recommend you read the wiki before going any further.

Thank you so much! Will try it tomorrow! I know, that the newer SPL-stuff is better, but I'm not so much into it, because I just run the WM5-Rom and wanted a SIM-Unlock. Because of warranty reasons (on 2nd device) I want to get back to the original SW SPL and so on. But I really think of installing WM6 when my device is completely back alive Thank you

Related

too much information gets confusing

hi all,
i've just bought a t-mobile vario 2
i;ve read the wiki & a few of the posts regarding upgrading
but to be honest it has so much information & sometimes the information is contradictory.. so it gets confusing
i've been using the uni for a year now
my point is
i want 2 upgrade my hermes 2 wm6
my boot screen says
herm300
IPL-1.01
SPL 1.40.Olipro
i can use a different/other sim card than t-mobile
how do i chek if my hermes is CID unlocked
and what radio i'm using & what's my bootloader number??
i try 2 read the splash screen after soft reset but the radio version goes away pretty fast
do i run POF's unlocker v3a? is it safe to run again, even if my phone is cid unlocked?
in order 2 upgrade 2 wm6
do i need to install olipros hard spl 2.10? and then run customruu?
this is what i mean by confusing?
i've upgraded my magician, uni & wizard
however they all had pretty easy/self explanatory directions?
i'm sorry for sounding like a noob, but its new territory....
thanx in advance
Is there a specific reason you want to CID the device? T-Mobile's data plan s pretty great so I have never seen the need to use another sim in my vario. You dont need to CID unlock to upgrade the rom.
As long as you have installed Olipro's spl to protect against bricking your phone it should be fairly safe to install a wm6 rom. If not, definitely install the current version of hard spl.
Once you have installed SPL, you then run the RUU.exe file that usually comes with the rom. Tha majority will have a tick box on the first page that says auto detect, which will check which version of spl you have installed and then run itself accordingly. It is best to have the current hardspl installed though.
Most of them dont touch your extended rom and only replace the OS rom contents. T-Mob's wm5 extended rom customizations wont work with wm6 anyway so you will need to go looking here for a cab file called (I Believe) tmobileukfixed.cab.
You will also need to look for newer versions of your pocket pc software as some older ones dont play nice with WM6.
Good luck, and if in doubt, read MrVanx's upgrade guide here: http://www.mrvanx.org/cms/
chrisjasper said:
Is there a specific reason you want to CID the device? T-Mobile's data plan s pretty great so I have never seen the need to use another sim in my vario. You dont need to CID unlock to upgrade the rom.
As long as you have installed Olipro's spl to protect against bricking your phone it should be fairly safe to install a wm6 rom. If not, definitely install the current version of hard spl.
Once you have installed SPL, you then run the RUU.exe file that usually comes with the rom. Tha majority will have a tick box on the first page that says auto detect, which will check which version of spl you have installed and then run itself accordingly. It is best to have the current hardspl installed though.
Most of them dont touch your extended rom and only replace the OS rom contents. T-Mob's wm5 extended rom customizations wont work with wm6 anyway so you will need to go looking here for a cab file called (I Believe) tmobileukfixed.cab.
You will also need to look for newer versions of your pocket pc software as some older ones dont play nice with WM6.
Good luck, and if in doubt, read MrVanx's upgrade guide here: http://www.mrvanx.org/cms/
Click to expand...
Click to collapse
i dont live in the uK
so the tmobile plan is not the usp
i need to unlock the extende rom as i like 2 install most of my progs on the extended rom and also my ringtones as the sd card takes a cople of seconds b4 it kicks in..
check the wiki under Bootloader information.
Using mtty, there is a command to check CID status.
todd_jg said:
check the wiki under Bootloader information.
Using mtty, there is a command to check CID status.
Click to expand...
Click to collapse
hi
i've managed 2 find out that my phones supercid
however i cant get mtty 2 work
i put the phone in bootloader
then i conect the phone via usb
when i rum mtty
it says usb port cannot open
i tried mtty 1.42 as well.....

FUNDAMENTAL requirement before trying a WM6 upgrade

I have been reading all across the forums how to CID unlock, upgrade etc. However, I am not able to find the ways to do seeminly essential homework before trying to upgrade. These for me are:-
* Finding a way to completely backup all the stuff from original tytn. Like ROM, SPL, IPL, Radio, CIDlock etc. I feel that this is important as if ever I feel like going to the tried old one I should be able to and to preserve the warranty also. Also, the method to roll back if needed. This should be covering re CID locking the phone etc.
It makes sense to create a way to bring the phone to its completlely original shape if we need it
Thanks
Alber
alber786 said:
I have been reading all across the forums how to CID unlock, upgrade etc. However, I am not able to find the ways to do seeminly essential homework before trying to upgrade. These for me are:-
* Finding a way to completely backup all the stuff from original tytn. Like ROM, SPL, IPL, Radio, CIDlock etc. I feel that this is important as if ever I feel like going to the tried old one I should be able to and to preserve the warranty also. Also, the method to roll back if needed. This should be covering re CID locking the phone etc.
It makes sense to create a way to bring the phone to its completlely original shape if we need it
Thanks
Alber
Click to expand...
Click to collapse
You do not need to back up your spl, ipl, etc. because if you need to roll back you can just reflash them on, and they can be found around here and in the wiki.
You cannot un-CIDunlock, but if you use hardspl v7 it will "trick" your phone into thinking it is (when in reality it isnt) so that you do not have to actually unlock it. If you ever need to send it in you can just flash the old spl over it.
mcorrie1121 said:
You do not need to back up your spl, ipl, etc. because if you need to roll back you can just reflash them on, and they can be found around here and in the wiki.
You cannot un-CIDunlock, but if you use hardspl v7 it will "trick" your phone into thinking it is (when in reality it isnt) so that you do not have to actually unlock it. If you ever need to send it in you can just flash the old spl over it.
Click to expand...
Click to collapse
So you mean that hardspl doesnt CID unlock it? But isnt there really a way to extract the original components and then put them back again ?
thanks
Alber
alber786 said:
So you mean that hardspl doesnt CID unlock it? But isnt there really a way to extract the original components and then put them back again ?
thanks
Alber
Click to expand...
Click to collapse
HardSPL does not CID unlock. pof's Free Unlocker (a sticky thread) does the SIM and CID unlocking. HardSPL is a new set of bootloaders allowing upgrade utilities to access and read/write to the phone. The most important aspect of this (besides bypassing the CID check) is the security - it has some overwrite protection built in to prevent you from accidentally corrupting the bootloader area, rendering your phone a brick. HardSPL is a safety measure.
If you check THE WIKI here on xda for the Hermes, you will find some stuff on extracting. It is most probable that it will be FAR easier to find new versions of everything you have, rather than trying to back up and restore. The wiki contains MANY shipped ROMs to allow you to restore back to basically the original condition. LOOK HERE for MW5 shipped ROMs and LOOK HERE for WM6 shipped ROMs.
todd_jg said:
HardSPL does not CID unlock. pof's Free Unlocker (a sticky thread) does the SIM and CID unlocking. HardSPL is a new set of bootloaders allowing upgrade utilities to access and read/write to the phone. The most important aspect of this (besides bypassing the CID check) is the security - it has some overwrite protection built in to prevent you from accidentally corrupting the bootloader area, rendering your phone a brick. HardSPL is a safety measure.
If you check THE WIKI here on xda for the Hermes, you will find some stuff on extracting. It is most probable that it will be FAR easier to find new versions of everything you have, rather than trying to back up and restore. The wiki contains MANY shipped ROMs to allow you to restore back to basically the original condition. LOOK HERE for MW5 shipped ROMs and LOOK HERE for WM6 shipped ROMs.
Click to expand...
Click to collapse
what about the radio upgrade
the htc108 thing
its confusing
on pof's sticky it says to downgrade the radio if u have the htc 108..
but on the radio upgrade sticky, it says u can upgrade any phone[hermes] using custom ruu..
todd_jg said:
HardSPL does not CID unlock. pof's Free Unlocker (a sticky thread) does the SIM and CID unlocking. HardSPL is a new set of bootloaders allowing upgrade utilities to access and read/write to the phone. The most important aspect of this (besides bypassing the CID check) is the security - it has some overwrite protection built in to prevent you from accidentally corrupting the bootloader area, rendering your phone a brick. HardSPL is a safety measure.
If you check THE WIKI here on xda for the Hermes, you will find some stuff on extracting. It is most probable that it will be FAR easier to find new versions of everything you have, rather than trying to back up and restore. The wiki contains MANY shipped ROMs to allow you to restore back to basically the original condition. LOOK HERE for MW5 shipped ROMs and LOOK HERE for WM6 shipped ROMs.
Click to expand...
Click to collapse
Thanks a lot for the reply, I appreciate the time you spent in expaining this to me and providing these links.
I was wondering if HARDSPL is like shelltool where it will only allow upgrade or flashing of OS part. So, once I use the HARDSPL and flash say HTC official WM6 release or Dopod WM6, will I be ableto to get the bundled radio and SPL and IPL upgrades from these ROMS? and if yes then will HARDSPL get replaced by these SPLs and IPLs built into the ROMS? One more thing, will an upgrade like that can brick the phone as if I rum the official ROM it will try to upgrade the SPL and IPL (I am not sure).
What is the preferred way of upgrading ? unlocking CID by the tool or HARDSPL ?
I have read somewhere that lockwiz tool used for Wizard can save CID also and some tool and put it back also but I dont know how and if the same tool can do it for hermes?
Regards,
Alber
alber786 said:
Thanks a lot for the reply, I appreciate the time you spent in expaining this to me and providing these links.
I was wondering if HARDSPL is like shelltool where it will only allow upgrade or flashing of OS part. So, once I use the HARDSPL and flash say HTC official WM6 release or Dopod WM6, will I be ableto to get the bundled radio and SPL and IPL upgrades from these ROMS? and if yes then will HARDSPL get replaced by these SPLs and IPLs built into the ROMS? One more thing, will an upgrade like that can brick the phone as if I rum the official ROM it will try to upgrade the SPL and IPL (I am not sure).
What is the preferred way of upgrading ? unlocking CID by the tool or HARDSPL ?
I have read somewhere that lockwiz tool used for Wizard can save CID also and some tool and put it back also but I dont know how and if the same tool can do it for hermes?
Regards,
Alber
Click to expand...
Click to collapse
Most cooked roms are os only, but a few have a radio, etc. included. If its os only, flashing will only change the os. You can separately flash radio.
Hardspl is the best because its reversible. Well thats not the best word to describe it....id say because its not permanent. But u know what i mean
alber786 said:
Thanks a lot for the reply, I appreciate the time you spent in expaining this to me and providing these links.
I was wondering if HARDSPL is like shelltool where it will only allow upgrade or flashing of OS part. So, once I use the HARDSPL and flash say HTC official WM6 release or Dopod WM6, will I be ableto to get the bundled radio and SPL and IPL upgrades from these ROMS? and if yes then will HARDSPL get replaced by these SPLs and IPLs built into the ROMS? One more thing, will an upgrade like that can brick the phone as if I rum the official ROM it will try to upgrade the SPL and IPL (I am not sure).
What is the preferred way of upgrading ? unlocking CID by the tool or HARDSPL ?
I have read somewhere that lockwiz tool used for Wizard can save CID also and some tool and put it back also but I dont know how and if the same tool can do it for hermes?
Regards,
Alber
Click to expand...
Click to collapse
Mcorrie1121 is right. I will add a couple of things.
1. HardSPL is not *necessary* for flashing anything, it only makes it safer and allows you to flash ROMs with CIDs that do not match your device without CID unlocking. Your ROM is basically a few parts - OS, Radio, IPL, SPL, ExtROM, MainSplash and SubSplash. The HardSPL will replace the SPL only. Most non-carrier ROM releases are OS only. Most carrier ROMs (as you pointed out) have ALL of these things. As Mcorrie1121 pointed out, you can easily find a radio - check the wiki, search, etc.
2. Once you have upgraded to a cooked ROM (and HardSPL), you will still be able to upgrade to a Shipped Official ROM. You may need to "unpack" it and use the CustomRUU instead of the shipped updater. That is OK though.
3. HardSPL will not allow overwriting of the IPL/SPL except by another HardSPL (see mrvanx.org downgrade guides). You will not have a problem. It will keep your bootloader zone safe.
4. I don't think there is a preferred way. Some people unlock CID, others do not. There is no reason to *not* unlock it, unless you plan to send it back - and I have never heard of someone getting service rejected for this reason. Wring ROM, yes. CID unlocked, no. That said, maybe try without CID unlocking first and then if you find you need to do it for some reason, then do it. You really do not have to do it, since the Custom Updater bypasses the CID check anyway.
5. Regarding the 0108 Radio BL issue, don't worry much about that - it is an old problem. Just don't go below whatever version you have now.
todd_jg said:
Mcorrie1121 is right. I will add a couple of things.
1. HardSPL is not *necessary* for flashing anything, it only makes it safer and allows you to flash ROMs with CIDs that do not match your device without CID unlocking. Your ROM is basically a few parts - OS, Radio, IPL, SPL, ExtROM, MainSplash and SubSplash. The HardSPL will replace the SPL only. Most non-carrier ROM releases are OS only. Most carrier ROMs (as you pointed out) have ALL of these things. As Mcorrie1121 pointed out, you can easily find a radio - check the wiki, search, etc.
2. Once you have upgraded to a cooked ROM (and HardSPL), you will still be able to upgrade to a Shipped Official ROM. You may need to "unpack" it and use the CustomRUU instead of the shipped updater. That is OK though.
3. HardSPL will not allow overwriting of the IPL/SPL except by another HardSPL (see mrvanx.org downgrade guides). You will not have a problem. It will keep your bootloader zone safe.
4. I don't think there is a preferred way. Some people unlock CID, others do not. There is no reason to *not* unlock it, unless you plan to send it back - and I have never heard of someone getting service rejected for this reason. Wring ROM, yes. CID unlocked, no. That said, maybe try without CID unlocking first and then if you find you need to do it for some reason, then do it. You really do not have to do it, since the Custom Updater bypasses the CID check anyway.
5. Regarding the 0108 Radio BL issue, don't worry much about that - it is an old problem. Just don't go below whatever version you have now.
Click to expand...
Click to collapse
Thanks, I appreciate your help. Please tell me if I can put back WM5 back on it after upgrading.
Regards,
Alber
todd_jg said:
Mcorrie1121 is right. I will add a couple of things.
1. HardSPL is not *necessary* for flashing anything, it only makes it safer and allows you to flash ROMs with CIDs that do not match your device without CID unlocking. Your ROM is basically a few parts - OS, Radio, IPL, SPL, ExtROM, MainSplash and SubSplash. The HardSPL will replace the SPL only. Most non-carrier ROM releases are OS only. Most carrier ROMs (as you pointed out) have ALL of these things. As Mcorrie1121 pointed out, you can easily find a radio - check the wiki, search, etc.
2. Once you have upgraded to a cooked ROM (and HardSPL), you will still be able to upgrade to a Shipped Official ROM. You may need to "unpack" it and use the CustomRUU instead of the shipped updater. That is OK though.
3. HardSPL will not allow overwriting of the IPL/SPL except by another HardSPL (see mrvanx.org downgrade guides). You will not have a problem. It will keep your bootloader zone safe.
4. I don't think there is a preferred way. Some people unlock CID, others do not. There is no reason to *not* unlock it, unless you plan to send it back - and I have never heard of someone getting service rejected for this reason. Wring ROM, yes. CID unlocked, no. That said, maybe try without CID unlocking first and then if you find you need to do it for some reason, then do it. You really do not have to do it, since the Custom Updater bypasses the CID check anyway.
5. Regarding the 0108 Radio BL issue, don't worry much about that - it is an old problem. Just don't go below whatever version you have now.
Click to expand...
Click to collapse
Dear, please help me with one thing-I am terribly confused about the procedure to upgrade my JASJAM to WM6. I understand that one way is to CIS unlock it and install on it the official and dopod releases of WM6. I wanted to know how can I do the same using the HARDspl. I know that I can install the HARDSPL but after that what ??? Can I then run the offcial RUU from HTC or Dopod or I am supposed to do it some other way as I am afraid that it may contain the SPL and IPL and can break by phone OR I have to use some customRUU (I dont know) OR I am supposed to extract the OS from these official releases (I dont know how) OR ..
Can you please clear these confusion??
I have:-
* I-Mate JASJAM, CID locked i suppose as when I run official HTC or dopod it says this update utility is not for this
*I really wanted to save my devices complete state and a way to revert it to the way it was like SPL, IPL, OS, Radio, CID lock etc.
PLS pls help
Regards,
Alber
alber786 said:
Dear, please help me with one thing-I am terribly confused about the procedure to upgrade my JASJAM to WM6. I understand that one way is to CIS unlock it and install on it the official and dopod releases of WM6. I wanted to know how can I do the same using the HARDspl. I know that I can install the HARDSPL but after that what ??? Can I then run the offcial RUU from HTC or Dopod or I am supposed to do it some other way as I am afraid that it may contain the SPL and IPL and can break by phone OR I have to use some customRUU (I dont know) OR I am supposed to extract the OS from these official releases (I dont know how) OR ..
Can you please clear these confusion??
I have:-
* I-Mate JASJAM, CID locked i suppose as when I run official HTC or dopod it says this update utility is not for this
*I really wanted to save my devices complete state and a way to revert it to the way it was like SPL, IPL, OS, Radio, CID lock etc.
PLS pls help
Regards,
Alber
Click to expand...
Click to collapse
CLICK THIS LINK
There are upgrade guides there and guides to put it back the way it was (OS, Radio, IPL, SPL, MainSplash and SubSplash) - it is all covered.
The upgrade guides will get you through the upgrade process. The only thing you need to do after that to use an official upgrade is to unrar (using winrar or something) the executable file and take the nbh and us it with the CustomRUU, which can be found HERE .

How to remove SPL/IPL from an official ROM?

I installed Olipro Hard SPL and am now able to try any wm6 ROM without SPL.
After having tried many of them, I would like to downgrade and try the last Qtek shipped ROM for wizard: QT_FR_9100_2170706_21707106_20710_180406.
But no matter how I try, I'm now unable to install that wm5 ROM.
Even my former SPV M3000 shipped ROM refuse to re-install.
I guess it's either a problem of RUU, or more probably a problem of SPL on those ROM.
I'd like to remove their SPL, but I don't know how to do.
Any tutorial, advice, or special no ID RUU that fits well those wm5 ROM?
The actual problem with this Rom is the RUU.
It won't let you downgrade.
However it is wise to get rid of the IPL/SPL, for safety and for keeping the hard SPL.
You can use typho5.exe to disassemble the ROM in parts, and use nbftool to re-assemble it without using the IPL/SPL.
They are available in the ROM kitchens.
Use the ruu in the hard spl thread for flashing.
Thanks for the reply, Equinoxe.
Actually I've already tried many RUU, not only the Ruu already included in the official ROM.
Mun RUU etc. But no luck, all kind of error occured but the the flashing remains impossible.
I'll try to find the tools you told me about and see whether removing IPL/SPL makes it easier to flash those ROM.
If you know any special RUU suitable for such a downgrade, please, let me know.
riri22 said:
Thanks for the reply, Equinoxe.
Actually I've already tried many RUU, not only the Ruu already included in the official ROM.
Mun RUU etc. But no luck, all kind of error occured but the the flashing remains impossible.
I'll try to find the tools you told me about and see whether removing IPL/SPL makes it easier to flash those ROM.
If you know any special RUU suitable for such a downgrade, please, let me know.
Click to expand...
Click to collapse
If Mun's RUU didn't do the trick, you better use the CORE pro kitchen.
You can extract the parts with typho5.exe
usage:
typho5.exe -x nk.nbf
all the parts will be created/extracted
Delete all the IPL_1 IPL_2 SPL_1 and SPL_2 parts
use nbftool to reassemble the ROM. (read the PDf to see the starting addresses, although nbftool should be patched to show the right addresses)
Good luck
EquinoXe
the-equinoxe said:
If Mun's RUU didn't do the trick, you better use the CORE pro kitchen.
You can extract the parts with typho5.exe
usage:
typho5.exe -x nk.nbf
all the parts will be created/extracted
Delete all the IPL_1 IPL_2 SPL_1 and SPL_2 parts
use nbftool to reassemble the ROM. (read the PDf to see the starting addresses, although nbftool should be patched to show the right addresses)
Good luck
EquinoXe
Click to expand...
Click to collapse
Hi Equinox, thanks for the reply.
I started trying to get typho working, but all I could see was a brief command prompt and nothing else.
Finally, I ended up using Molski DevPack, which already includes those tools, in quite an ergonomic way.
After finding a guide about using those tools, It took me, no kidding about 10 mn for the whole process and 5 more to do the flashing.
I used nb2nbf_wizard to reassemble the ROM with only the parts I wanted to keep, including the extended ROM.
Regarding the address, it did it automatically, except for the HTC logo that I did manually, and also for the name of the Extended and Logo I renamed according to the sample jpeg showing that soft in action.
Since I kept the extended ROM and the original splash and logo screen, and I now have an authentic Qtek Wizard, just for fun.
But the most important is the feeling of building one's own ROM, according to your own taste and choice. Wonderful.
You were right: after having removed SPL/IPL and rebuilt the ROM, the Mun RUU worked flawlessly to flash my so called Qtek ROM onto my wizard.
In the meantime, It got rid of the pile of miscellanous splash screens and logos that were left since the install of all previous wm6 ROM.
Thanks again for the tips.
P.S.: the guide I used to understand how to use the Molski DevPack:
http://forum.xda-developers.com/showthread.php?t=320910&highlight=RUU_2001
Can't update rom anymore
Info about phone
WIZA200
IPL 2.21.0001
SPL 2.21.olip
GSM 02.19.11
OS 6.0.0.0
TNT_5.0_Wizard_TouchFLO
Windows XP
Active Sync 4.5 (Works Fine)
When i try to install another ROM i get communication error[224] : DEVICE NOT RESPONDING
When i try to install Cert_SPCS.cab or EnableRapi.cab or TomTom i get installation of xxxx.cab was unsuccessful.
Please help

Fall Back to Original Rom (Tmobile)

Hi @ all...
so time has come i will return my phone to tmobile, because of the heavy problems with the slide-out-keyboard. i tried to solve my keyboard-problems with the orignal shipped rom, but i realised that it doesn't matter which rom i flash to my phone, the problem seems to be of hardware-ish nature...
so now my problem is: i want to fall back to the original state...
i want original IPL,SPL,OS,Radio, Boot, etc etc...
i tried to flash the "Original Shipped TMOB101" from the wiki, it flashed nice with CustomRUU...the original flash utility couldn't find my phone.
so i unpacked the exe and flashed the nbh with CustomRUU... flashed nicely, but didn't boot... first problem: whitescreen, second: hang on windows mobile screen, third: NOGSM... tried to flash newer GSM 1.43. this worked nice then, but isn't original... any idea how to get the 1.05.02 radio running? tried to reflash the complete tmobile nbh again, same result.
tried to flash with Vista, and also with XP, nothing changed...
next problem i assume is: how to downgrade SPL? and how to detect Bootversion? could it be, that i flashed some newer boot in between, because, i have always flashed newest radio roms, could it be that i flashed a boot together with a certain radio?
hope someone can help me... my device is also simunlocked, i hope they do not recognize it at tmobile. but i want to get everything else into original state before returning.
greetings
garfield
There is now an official wm6 update which you can use
it's available here:
http://forum.xda-developers.com/showthread.php?t=337163
If you're wondering if it's properly been released, it's also available on the t-mobile business site.
Shaks
shaks1979,
I have just been to the tmobile business site and I cannot find the WM6 update - please can you post a link to it?
many thanks,
Paul
the german t-mobile site dies not offer to download the upgrade yet.
flashed the new WM6 from t-mobile yesterday, and it works really great, but my keyboard isn't functional anyway...
has anyone an idea how to enable the flash-utility to overwrite the SPl and IPL? because my tri-color-screen reads IPL-1.01 and SPL-2.10-Olipro and this means, both of them have not been updated... any way to overwrite these rom-sections with the now tmobile ones?
so when finished upgrading (IPL and SPL have to be upgraded before i can go on) i will return my phone to a tcom store, they have to bother with my keyboard issue... my phone isn't a half year old by now... keyboard issues like this shouldn't be there i assume
greetings
and thanks for the new wm6 links.
garfield
Extract the nbh file from the T-Mobile ROM and flash it with CustomRUU. This will overwrite IPL / SPL
[...see reason]
which settings do i have to use with CustomRUU? do i have to select same radio-buttons as always? (SPL 2.10-Olipro/Is it HardSPL) ?
okay, so i found the option via try and error i had to use use: Force UNSAFE SSPL.
i have another question now:
as far as i know, t-mobile DE has not released this ROM to its customers via their website, so i have to flash my phone back to WM5 original rom, and bootloaders, because this new tmobile rom didn't make my problems with the keyboard go away.
my local store told me that they will send the device back to tmobile, and tmobile then will repair or exchange the device.
so if they send it back to tmobile, i uess i have to put it into original state, haven't i? cause flashing the rom causes loss of warranty, doesn't it? i hope they will not recognize, that i sim-unlocked it (did not touch the CID).
problem occurring: i extracted the nbh from the original shipped-archive and flashed it with CustomRUU but when booting NO GSM shows up, and windows stops booting during first bootsplash... sometime during second bootsplash... any idea? might it be that it was like this, because of olipros 2.10 SPL?
greetings
garfield
I wonder why you SIM unlocked your device?
The German Hermes never was SIM locked, so, there was no need to unlock it!
You will either have to Soft-CID-unlock or Hard-CID-unlock your device if you want to flash it otherwise it won't work!
What settings are you talking about? You simply copy the nbh file to the CustomRUU folder and run the UPDATE UTILITY in there! There are no settings, it works the same way as the utilities from shipped ROMs - simply follow the instructions on screen and do not plug out nor touch the device until the job is done!
So actually it is not a hermes, it is a MDA Vario 2 from tmobile, isn't it?
partly you're right, the device wasn't sim-locked, but net-locked, wich means i cannot use my second sim card from vodafone with it. so i had to unlock it.
(i tried without unlocking, the phone asked me for a certain code and no, it was not the pin-code from the vodafone-sim )
if you launch CustomRUU you are asked for the version of your SPL, at least this is what happens when i start it. if you cannot imagine what i am talking about, i will make a screenshot, for better understandings.
I had Hard-SPL installed, this is a form of SOFT-CID-unlocking?
with having Hard-SPL installed i could not boot the original shipped german TMOB101-rom from the wiki...
can i flash the old ipl/spl/radio/os without worries?
greetings
garfield
Within the CustomRUU folder you should see a file called ROMUpgradeUt.exe - this never ever asks for SPL, it is nothing but a modified FLASHING UTILITY.
i only have ruuwrapper.exe
i used this customruu v5.2 from olipro's thread
what customruu are you talking about? actually i never saw a file named ROMUpgradeUt.exe
where to find?
thanks for your help.
greetings
garfield
EDIT:
i have just found this:
NOTE: If your radio version is currently HIGHER than 1.27.00.00 then it is very likely the radio bootloader is version 0108, this WILL NOT allow the radio to be downgraded to a radio containing BL 0106 and will result in a "NO GSM" error. As with other downgrade guides this is NOT intended as a guide for claiming the warranty of the device having flashed components which are not authorised by the manufacturer or carrier.
Click to expand...
Click to collapse
on the WM5-Downgrade site over @mrvanx.org

Need some quick help!

I recently flashed my Wizard with TNT WM6 and I am getting all kinds of problems so I am wanting to bring it back to Wizard Love so I can attempt TNT's again and avoid a "bad flash".
My question is, do I need to put the phone in the bootloader (i.e. the 3 colored bars?) or can I flash it with the phone loaded and everything. I am using RUU to flash.
Or do I need to use ShellTool?
If its a G3,then simply hook up the phone with pc and run the RUU,it'll reflash,there's no need to get into Bootloaders (RGB Screen).
But if its a G4,then how did you upgrade first,if through HardSPL,then again just hook up and run the RUU,well,if you used Shelltool,then there's no need to go through again with Shelltool.Get the phone HardSPL once,then you can flash any rom as much as you like
I used shelltool for the first flash, but it kind messed up so I had to redo Wizard Love with the RGB boot loader.
If I remember correctly by "messed up" I think it froze during flashing.
Yes I do have a G4
well do as zabardast_1's has said and flash HardSPL to your g4 wizard and then you can just flash another cooked rom
and added....Don't use ShellTool again even you are using a G4! RUU can be used on G4 directly given that you have installed HardSPL and you are going to flash a custom ROM posted here.
So even though ShellTool kinda messed up, my device is still HardSPL'ed?
To be safe you can flash using Softspl , that is the way i flashed few times althouhg my wizard was hardspl and it was ok. If you have hardspl try using Mun's RUU . Both methods worked fine for me.
Ok, I just re-flashed my G4 with Wizard Love using the RUU that it came with and everything seemed to work fine. Does this mean that my HardSPL was successful? See what I think had happened was I flashed TNT's rom with ShellTool and not RUU after I had HardSPL'ed my device. Could that have had something to do with it?
Thanks for all the help so far, you guys have been very knowledgeable.
Read this maybe its helpfull for you http://forum.xda-developers.com/showthread.php?t=435852
Mortifix said:
Ok, I just re-flashed my G4 with Wizard Love using the RUU that it came with and everything seemed to work fine. Does this mean that my HardSPL was successful? See what I think had happened was I flashed TNT's rom with ShellTool and not RUU after I had HardSPL'ed my device. Could that have had something to do with it?
Thanks for all the help so far, you guys have been very knowledgeable.
Click to expand...
Click to collapse
Ah! You are mixing up all three methods Shelltool,RUU,HardSPL together,they all are different methods to flash a rom.Shelltool is a different method then RUU(RomUpdateUtility) and HardSPL(Patched IPL/SPL) is altogether a different process to flash and upgrade a G4 device.
Try to read all about these methods for better understanding.
Here, I wud not like to go into details,you can read about these methods in their respective threads.
Flashing wizard_love rom doesn't mean your phone is HardSPL'd ? No,wizard_love rom is a patched rom,it'll flash to any G4 device with original official IPL/SPL (Bootloaders) running on it,but if the phone is HardSPL'd,it flashes patched IPL/SPL,thus tricking it to think its semi-permanent CID unlocked,after this its possible to flash any wm6.1 custom rom.But flashing a wizard_love,it still has its own official IPL/SPL,but you cannot upgrade to any wm6 rom as its not CID unlocked.As a G4 device cannot be CID unlocked like a G3 phone,so KardSPL is applied to make it trick into semi-permanent CID unlock,whereas,its in fact CID locked,but here its possible to upgrade to any wm6 rom,hope you got my point !!!
So,if you want to upgrade to wm6 or flash TNT wm6.1 rom,you have to first apply HardSPL,it'll change the IPL/SPL of the phone,only then you can flash TNT wm6.1 rom
Ok yeah thanks for clearing that up for me I was trying to update my phone with the RUU that came with TNT .20273, but it kept giving me an Error 300 which I am assuming that means its not HardSPL'ed. So from the sounds of it, I would probably like to get my phone HardSPL to I can flash any new roms that come out. I was under the assumption that ShellTool was HardSPL'ing my phone, but I guess not. Before I proceed to the next step, is this the instructions I should be following?: http://forum.xda-developers.com/showthread.php?t=332320
EDIT:
Ok, I went ahead and HardSPL'ed my device. I followed the instructions on that thread and everything seems to be working. I get SoftSPL: something something olipro so I am guessing thats good. I am still having problems when I go to flash TNT. I am trying to use the RUU that is included with TNT, but I keep getting Error 300 (Invalid Update Tool).
ok,download 'Mun's RUU' from the HardSPL thread you just posted above and replace the RUU in this zipfile with RUU in the TNT rom and run this replaced RUU,it'll work and flash the rom
I have everything all set and I am rocking TNT .191213. Thanks for all the help guys!!

Categories

Resources