I have an O2 Atom in which while flashing the bootloader part, power went off...
Now i cannot enter bootloader mode i.e. the screen is blank and the handset is dead...
It just shows the Red LED when i connect charger to it...
Any help would be greatly appreciated in unbrickng my handset...
When you connect USB appers USB in your screen? if yes, the bootloader is ok, just try upgrade the rom again. This happen with me once...
and if it does not... then you'll have to bring it to the O2 service center to have them reflash your atom.
Related
Ok i have a MDA, i updated the rom, and now it wont turn on at all, But when i plug it into the wall charger it comes up with bootloader, Well when i unplug it it just shuts off, try pluging it into my Pc it wont turn on, Only turns on with wallcharger, I am need to find a way to get back to bootload when its usb connect so i can flash, Can anybuddy help And yes i did search before i post, sorry i am in a panic..
deathblooms237 said:
Ok i have a MDA, i updated the rom, and now it wont turn on at all, But when i plug it into the wall charger it comes up with bootloader, Well when i unplug it it just shuts off, try pluging it into my Pc it wont turn on, Only turns on with wallcharger, I am need to find a way to get back to bootload when its usb connect so i can flash, Can anybuddy help And yes i did search before i post, sorry i am in a panic..
Click to expand...
Click to collapse
There are 2 ways I can think of to fix this. One way is to charge the phone with the wall charger first. Hold the camera button while pressing and holding the power button. This should put the device in bootloader while not plugged in to the wall and get the PC ready before connecting the USB to the phone. Make sure you have a full charge before you do this because it sounds like your battery died while flashing. If you do this, you should be able to get it connected to a computer long enough to flash it back to normal.
Seccond option, if battery will not charge in bootloader mode or when device is turned off, buy new battery and then follow steps above.
I hope this helps... I personally have never had this problem before.
No connection in bootloader mode
After a rom update has interrupted by 96% (and did not finish) I have no chance to connect my mda vario to my laptop. I still come to bootloader mode but no step further.
Have anybody an idea to solve this problem. Is there any other chance to get a connection to flash the rom again?
Many thanks in anticipation for any assistance!
Frisvo
i erased boot by misyake any body help me how to restor boot device now fully dead
just orange led when i plug usb
You should search the forums first, however, this might help http://forum.xda-developers.com/showthread.php?t=331818&page=2
thx mate for replay
but not help coz device totaly dead anad dont enter boot loader
abcrino50
Use JTAG cable and JFLASHMM software to restore bootloader.
And learn russian Boys from 4pda.ru already restored their bootloaders.
PLEASE LEARN TO READ THE WIKI PAGE...after reading this , last resort is the forum
http://wiki.xda-developers.com/index.php?pagename=ATOM_BRICK
Your device is bricked, if and only if, your device won't start normally... even if you press soft-reset, hard-reset, or even bootloader mode buttons. Usually a brick is caused by improper ROM upgrade, and using tools that modify the ROM. Before panicking, do the following:
Brick Test:
1. Make sure your device has ample battery charge. If you're not sure plug it in with the wall charger for at least 10min
2. Remove your battery for at least 1 minute
3. Replace your battery while observing the LED lights
4. If the LED blinks once upon battery insertion, you might have hope yet
The only way to upgrade on a semi-brick device, is to upgrade through bootloader mode. No bootloader mode, No upgrade possible - period.
Entering Bootloader Mode on Semi-Brick Atom:
1. Remove battery for for at least 1 minute
2. Press CAMERA+RESET(stylus) simultaneously
3. Insert battery while still holding the buttons
4. Release the buttons at the same time (You should see bootloader screen)
Note: Failure to hold the buttons at the same time during battery insertion will cause it not to work.
----------------------------------------------
If nothing HAPPENED after this trial of revival, your atom MAYBE BRICKED/forever dead.
If there is no LED LIGHT on ur atom, YOUR ATOM IS BRICKED.
sorry my friend, your phone is a paperweight NOW if this is the situation.
LAST RESORT: O2 service center, ur lucky if they have support in ur country. but the price for fixing (if not under warranty)...mmmm a new iphone ;-)
abcrino50 said:
i erased boot by misyake any body help me how to restor boot device now fully dead
just orange led when i plug usb
Click to expand...
Click to collapse
abcrino50
Please read
http://forum.xda-developers.com/showthread.php?t=336278
and waiting 1-3 days
PLEASE SOMEBODY HELP ME
TWO WEEK AGO MY ATOM WAS DEAD
IAM HAVE BEEN TRY TO HARD RESET ALSO MN1 BOOT LOADER ( POWER BUTTON+CAMERA BUTTON). BUT DOESN'T WORK.
SO TODAY IAM TRY TO FLASH BOOT LOADER FROM JTAG PORT, AFTER FINISH FLASH PROGRAMED MY ATOM STILL DEAD.
SOMEBODY PLEASE HELP...
Okay, firstly dont put everything in caps.. its EXTREMELY annoying. Secondly, the device turns on correct? if it does then just try flashing from either your PC through Activesync OR via a memory card with a ROM on it. Consider using a stable ROM from either a ROM Chef or the O2/MWG website.
Aegishua said:
Okay, firstly dont put everything in caps.. its EXTREMELY annoying. Secondly, the device turns on correct? if it does then just try flashing from either your PC through Activesync OR via a memory card with a ROM on it. Consider using a stable ROM from either a ROM Chef or the O2/MWG website.
Click to expand...
Click to collapse
Haii.. thank you for your respon soon.
for your information my PDA totaly malfuction. that no respon when iam press power buton+camera buttonto go to MN1 boot loader .
only red lamp on when the PDA connect with charger battery.
Hmm okay.. so that means it still charges. You should try charging it for an extended period of time and then turning the device on. If the device comes up with the Manufacturer logo then you should just soft reset it and hold down your bootloader combination and go from there. However, if it doesnt even come up with the Manufacturer logo then you should consider getting it repaired.
Hii...i was do to charge my PDA also iam test with volt meter that battery is full power 4,2 volt dc.
So i try to push power button than my PDA doesn't start till now....
Atom Brick Solution...
suga_ngr said:
Hii...i was do to charge my PDA also iam test with volt meter that battery is full power 4,2 volt dc.
So i try to push power button than my PDA doesn't start till now....
Click to expand...
Click to collapse
Have you search on wiki?
I've been through that condition, last night actually when I pressed the wrong button (Power Button) when the MN1 bootloader looked for diskimg.nb0.
My device was near to death. I couldn't find the MN1 bootloader on my device's screen when I pressed the CAMERA+RESET(stylus). It remains dead until :
-I search the solution on http://wiki.xda-developers.com/index.php?pagename=ATOM_BRICK, I could see my device running its MN1 Bootloader
and looked for the ROM (diskimg.nb0) again and continued the ROM installation process
How to get the diskimg.nb0 please read this page :
http://wiki.xda-developers.com/index.php?pagename=ATOM_SDCARD
Maybe atom pure had the same step with atom exec when we try to solve the Brick Problem.
Cheers...
TOM PURE Dead
With my experience my atom was hardware broken.
somebody please tell me where i can buy atom hardware cause iam very love my atom...
try th!s tr!ck (cb ini mas)
yesterday 09 jan 10 it's happened same to me.
my case is downgrade from h3llow0rd1 6.1 to PD4v!et 19971 by m3dk!d.
then atom hang up.. dead! no screen, cann't boot or ON.. but still can charging
This tr!ck may be this could help u..
1. charging, look red lamp is on
2. then try replace battery, then put back on. it will blink (button call and end call will blinK)
3. with stylus try reset with pressing record button
4. if your lucky then it will show you boot loader screen
Now my atom is back again using Hell0w0rd R0M ... (^_^)
suga_ngr said:
With my experience my atom was hardware broken.
somebody please tell me where i can buy atom hardware cause iam very love my atom...
Click to expand...
Click to collapse
Entering BootLoader Mode:
1.Remove Battery
2.Press Camera button and hold it while insert the battery.
3.Press Reset with stylus (keep holding camera button)
If you're lucky, you'll be directed to bootloader mode.
try to push the power & camera button together while inserting the battery and then enter the bootloader mode camera+reset button.
My Atom Life (was) dead, too
..but only for awhile
this happened when I tried to flash this Bajok ROM.
I'm not new to flashing, but that kinda make me 'a little' careless this time.
I transferred the .dio file using active sync explorer while doing other stuff with my laptop.. soon after, I see that the file transfer is done, cause the window is closed. As usual, I do the rec button + reset ritual and flashed away..
I again continued my other works and got mesmerized in it for a moment or two.
Half an hour later I realized that my atom has been showing bootscreen for quite some time..
My first failed flash! Well, I thought, this is it...
Just to make sure, I pulled out the battery, put it back again and reboot.. still the same stuckness... Then, I figured that since this was caused by ROm flashing failure, why dont check the .dio file? So I did. I pulled out the memory card, put it in a card reader and explore it.. I notice that the .dio file is only 18 megs.. whatta..? The original .dio is like 70 megs, so it must had been transferred it incomplete.
So with high hope, I retrasferred the file, this time completely.
I inserted again the battery and repeated the rec button + reset ritual..
Boot loader appeared and flashed away like a charm!
while i was updating my t-mobile hd2 i unplugged the usb cable and now the phone is dead and it shows me just update crash. if someone can help me please do that. thanks
try to turn off ur device and turn it on with holding vol down to enter bootloader withr three colours then connect ur device and start flashing ur rom
i did that but it doesent want to start updating it stayes on 0%
Why in the heck did you unplug? Did you do that in the middle of the flash?
yes unfortunately did that
I have xperia neo L and it stopped working it won't turn on... Here are the simptoms, when i press power button it vibrates and nothing else... Display won't turn on there are no sounds nothing... When i put it to charger if battery is low it shows orange light and when it charges it goes green... I tried seus and it completely reinstalls the software and same thing happens... Tried flashtool and all versions of stock roms same thing...
It goes to flash mode when i press back button and connect it to usb and it flashes phone succesfully and nothing... When i disconect phone and connect it again Flashtool sais that device is connected with usb debbuging off... So it detects phone... I even tried for fun to connect device without pressing power button, i connected it to usb then pressed home button and it installed as mass storage device, i'll place screenshots... I thought first maybe display is broken but it isn't... When i put sim card in phone and turn it on i'm always unavailable... Don't know what to do next? Any advices? Exept from thaking it to service, i will do that eventually but for few more days i want to tray fixing it myself... I would appreciate any advice... Thnx guys
Keep the device fully charged and try seus..Then again pin in charger only then after switch on. It may work