I think I have done a mistake.... I tried to upgrade my S200 from 2.15... to the v4.0.0.0.5 cross ! At first I've updated it with 'Prophet_PV_Temp' and it was successful so I've been in the step 2 : 'Prophet_PDAViet_4.0.0.0.5_Cross'. I though that it was successful so I unplugged my USB.... and it was not finished !!!!! And now my S200 wouldn't start properly, and it's stucked in the second screen which I can read :
IPL 2.10.0001
SPL 2.15.0001
GSM 02.30.21
0S 4.0.0.0 and I think it should be OS 4.0.0.0.5 !!
How can I do to fix it? I don't want to put it in a trashbin... HELP HELP HEL¨P
Edit/Delete Message
baptiste said:
I think I have done a mistake.... I tried to upgrade my S200 from 2.15... to the v4.0.0.0.5 cross ! At first I've updated it with 'Prophet_PV_Temp' and it was successful so I've been in the step 2 : 'Prophet_PDAViet_4.0.0.0.5_Cross'. I though that it was successful so I unplugged my USB.... and it was not finished !!!!! And now my S200 wouldn't start properly, and it's stucked in the second screen which I can read :
IPL 2.10.0001
SPL 2.15.0001
GSM 02.30.21
0S 4.0.0.0 and I think it should be OS 4.0.0.0.5 !!
How can I do to fix it? I don't want to put it in a trashbin... HELP HELP HEL¨P
Edit/Delete Message
Click to expand...
Click to collapse
Don't panic; do a hard-reset to your phone again (holding the camera key + comm key in the side together AND stick the hole in the bottom of the phone, while keeping the 2 keys held, until you see the screen shows some words); and repeat steps 1 and 2 altogether.
Thx for your reply,
holding the camera key + comm key in the side together AND stick the hole in the bottom of the phone, while keeping the 2 keys held, until you see the screen shows some words
Click to expand...
Click to collapse
I've done it many times but it still stucked.... Have you got any ideas?
Oh dear! I seem to have managed to do this too. Unfortunately in the middle of doing step 2 of the pdamobiz upgrade, my brother managed to kick the usb lead out of my laptop, disconnecting my m600 prophet!
I have tried the above steps & hard reset, but the phone is still stuck at the boot up screen as described above. I can't sync with my laptop again in order to run the AKU2 update, coz activesync wont recognise a device attached while it's stuck at the boot screen.
Is my phone now a rather expensive paperweight/weapon with which to bludgeon my brother?
Thanks for any help - I have searched quite a bit for an answer to this issue but found nothing.
sometimes it just takes a couple tries. let it sit for a while and do it again. i know i have had to do this a couple times in the past and just now it happened with my jamin so im reflashing it a second time. it just happens.
cardingtr said:
Put it in Bootloader mode (tricolor)by press-and-holding the Camera button and reset. Then do the first step (load the WM5 NVIDrom), hard reset, and do the second step (flash with WM6 Rom of choice). Be patient it takes approx 15 mins. All these step make sure you have USB connection.
Click to expand...
Click to collapse
and it works for me... ouffff !!!
Related
Hi does anyone know if there are WM6 ROMs for the SPV C550 if not are there any good WM5 ones?
look topic about wm5 for hurricane, there are also links to wm6 for hurricane device
hello again
here is latest, almost perfect rom for hurricane:
http://rapidshare.com/files/56833250/566.zip.html
and new SPL for this device:
http://rapidshare.com/files/56616745/spl566wm6_spfans2006.rar
lazaj007 said:
hello again
here is latest, almost perfect rom for hurricane:
http://rapidshare.com/files/56833250/566.zip.html
and new SPL for this device:
http://rapidshare.com/files/56616745/spl566wm6_spfans2006.rar
Click to expand...
Click to collapse
Has anybody tried this ROM?
lazaj007 said:
hello again
here is latest, almost perfect rom for hurricane:
http://rapidshare.com/files/56833250/566.zip.html
and new SPL for this device:
http://rapidshare.com/files/56616745/spl566wm6_spfans2006.rar
Click to expand...
Click to collapse
Ideal thanks
So is the 566.zip the WM5 or WM6 rom and has it been tested?
Whats the new SPL?
hI ALL, can u tell me the mini guide how to install this rom? I did it once to my sda but I dont remember now, where is the nbfupdatetool and RUU and patched RUU..???
when I type l c:\wm6.bin it give me this:
clean up the image temp buffer at 0x8C080000 Length 0x01B00000 MTTYDownloadImageNot allow operation!
Error : DownloadImage return error (code = 0xFFFFFFFF)
cmd>
maybe damaged rom, or any idea?
Gang: Make sure you're CID unlocked. (Eg, when you issue "info 2", it says HTCSuperCID).
How can do that cid unlock? give me some working link to download that tool or something. thx
here you go
http//www.spv-developers.com/content/SPV-Services.zip
you must check "CID Tool (Alpha)" and click set CID=11111111
after this restart your phone
and short solutions about wm6 installing:
* installation is the same like typhoon
-unlock Super CID
-upgrade new SPL (Patched ruu)
-disable USB connection in ActiveSync
-switch off your phone
-press and hold camera button, and put USB cable to your phone
-next check "Y"
-when your phone will be in bootloader mode (tri color screen) run mtty
- check USB connection in this program
and write: - info 2
- format BINFS
- l c:\566.bin (localization of your rom)
after succeful installising reboot your phone and it will be end
rom is very good, baterry work better
hmm, thx for guide, I believe it will work, but I have little problem : now I cant even connect to activesync so I cant do cid unlock, any idea how to fix that
lazaj007 said:
here you go
http//www.spv-developers.com/content/SPV-Services.zip
you must check "CID Tool (Alpha)" and click set CID=11111111
after this restart your phone
and short solutions about wm6 installing:
* installation is the same like typhoon
-unlock Super CID
-upgrade new SPL (Patched ruu)
-disable USB connection in ActiveSync
-switch off your phone
-press and hold camera button, and put USB cable to your phone
-next check "Y"
-when your phone will be in bootloader mode (tri color screen) run mtty
- check USB connection in this program
and write: - info 2
- format BINFS
- l c:\566.bin (localization of your rom)
after succeful installising reboot your phone and it will be end
rom is very good, baterry work better
Click to expand...
Click to collapse
Thanks for helping out!
A few questions?
1. This link "http//www.spv-developers.com/content/SPV-Services.zip" takes me to Wikipedia.
2. Where can I find the patched ruu to update the spl. It wasn't in the zip file?
Thanks in advance!
to Mr MIAGY :
1. just write that link starting with www. (without http//, or type http://)
2. in ''wm6 for c550'' topic u will find patched RUU and all needed files, they are ziped together
gangstaunitg said:
to Mr MIAGY :
1. just write that link starting with www. (without http//, or type http://)
2. in ''wm6 for c550'' topic u will find patched RUU and all needed files, they are ziped together
Click to expand...
Click to collapse
DoH! I didn't notice the missing ":"
Cheers!
Anybody have idea why I cant connect to activesync after spl upgrade ? Before spl upgrade it all goes well. Can I do something with it?
if upgrade was complited succes then you must turn off USB connection in Active sync, then run bootloder mode and do everything with instructions.
I did it !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
THank u all, thankS
This rom is amazing, everything work perfect, and it looks beautiful,
one more time thank you. jUUHHHUUUUUUUUU
lazaj007 said:
if upgrade was complited succes then you must turn off USB connection in Active sync, then run bootloder mode and do everything with instructions.
Click to expand...
Click to collapse
Upgrade reported as success
However after reboot I see the WM6 boot screen - loverly ...
Then the Mobile Operator Splash screen ... THEN
After too long ... the phone switches itself off and I have to take the battery out to get reponse again.
Any ideas?
It's a C550 ....
MrMiyagi said:
Upgrade reported as success
However after reboot I see the WM6 boot screen - loverly ...
Then the Mobile Operator Splash screen ... THEN
After too long ... the phone switches itself off and I have to take the battery out to get reponse again.
Any ideas?
It's a C550 ....
Click to expand...
Click to collapse
Ok, so a report. The phone boots, goes through WM6 splash screen, then operator screen, then APPARENTLY dead black screen.
BUT I plugged in the USB cable and the screen came on! WM6 Setup screen! All good go through setup eveything looks GREAT!
Only problem is, if I leave the phone alone for a bout a minute, the screen goes black AGAIN. Then no amount of key pressing on the device will bring it back to life.
Plugging the USB cable in brings it instantly back to life! But This means I can't wander too far from my PC ;-)
ANY Ideas
BTW IT LOOKS FANTASTIC! If I can just get around this issue ;-)
MrMiyagi said:
Ok, so a report. The phone boots, goes through WM6 splash screen, then operator screen, then APPARENTLY dead black screen.
BUT I plugged in the USB cable and the screen came on! WM6 Setup screen! All good go through setup eveything looks GREAT!
Only problem is, if I leave the phone alone for a bout a minute, the screen goes black AGAIN. Then no amount of key pressing on the device will bring it back to life.
Plugging the USB cable in brings it instantly back to life! But This means I can't wander too far from my PC ;-)
ANY Ideas
BTW IT LOOKS FANTASTIC! If I can just get around this issue ;-)
Click to expand...
Click to collapse
Heh heh ... seems I'm posting to myself ... that's cool I like my own company ... So I reflashed the SPL and some of the problems have gone away.
Phone will boot OK now ... but it will still "go to blank screen" and require plugging into the USB cable to "wake it up"
I'm out of ideas now ...
i'm a newbie
i'm to excite to upgrade my new 818 pro G4 WM 5 which i bought last week..i read few post regarding on how to upgrade into WM 6..then..
1stly i've tried the upgrade package,click the hardSPL,works well after that..but i'm quite lost for step 3 & 4..so i just stop there..
i noted that my SPL change into 2.G4.4PDA
then i read korand post, bout that new rom..i've tried it & it works well,my 818 pro with WM 6..
at the same time, i try to upgrade my IPL into 2.20 but after download it,my avast detect trojan in it..so i just leave it
then i read bout crystal rom..get so excite with the features & function (also the touchflo)
so i upgrade it..
now is the problem..
after i make the hard reset (camera button, comm button & on/off (soft reset button) & reset button below(next to usb/cable slot)..
i STUCK in boot screen which shows
IPL 2.15.0001
SPL 2.G4.4PDA
GSM 02.19.21
OS 6.0.0.255
it just stuck there,no led light..
i've tried upgrade rom back to normal,but no avail as my activesync cannot detect my device.
i've tried the hard reset for few time,yet nothing happen..still the same
searchin for help in wiki,yet still no solution or maybe i'm to panic
plz help me to restore it,or maybe make it alive as normal again..
Finally !!..i've made it
for overnight i searchin & lookin how to restore my device..
(not enough sleep )
this is how i do it instead doing the usually hard reset..
my device is on & the usb cable from my device connect to laptop..
yet still stuck at the boot screen..then
i press the green button (to make phone call) + comm button + soft reset (on/off button) all a the same time (those 3 button only)
then my screen turn into 3 different color..red,green or blue (i dont quite remember already hihihi)
so, i use the 'korand' rom update utility to restore it..with his wm 6 rom
waallaa..my 818 pro is alive again...with wm 6 !!
thanks to korand for his rom, or from whomever the contributer..thank a lots !!
i think i still wanna upgrade into different type of rom..
but my SPL looks different then normal SPL i've see..
SPL 2.G4.4PDA
can anyone could lead me where can i get IPL G4.zip free virus?
well, hope this post could help others who face the same problm as mine..
next time i'll be MORE carefull..
bye..
duato said:
for overnight i searchin & lookin how to restore my device..
(not enough sleep )
this is how i do it instead doing the usually hard reset..
my device is on & the usb cable from my device connect to laptop..
yet still stuck at the boot screen..then
i press the green button (to make phone call) + comm button + soft reset (on/off button) all a the same time (those 3 button only)
then my screen turn into 3 different color..red,green or blue (i dont quite remember already hihihi)
so, i use the 'korand' rom update utility to restore it..with his wm 6 rom
waallaa..my 818 pro is alive again...with wm 6 !!
thanks to korand for his rom, or from whomever the contributer..thank a lots !!
i think i still wanna upgrade into different type of rom..
but my SPL looks different then normal SPL i've see..
SPL 2.G4.4PDA
can anyone could lead me where can i get IPL G4.zip free virus?
well, hope this post could help others who face the same problm as mine..
next time i'll be MORE carefull..
bye..
Click to expand...
Click to collapse
I just have one thing to say you play with your "IPL" when you don't know what you are doing and you brick your phone for real !! and I mean you will brick it as like it wont even turn on !! don't think about playing around with IPL. your SPL is fine. it's HardSPL now. you can upgrade other roms, just read the wm6 guide , follow step by step and you will be fine.
one more time, if you like your device and you want to keep it (and use it) don't play around with it's IPL
true..totally agree with you..
well, i guess i do like this kind of tech..i'm fast learning (usually from mistakes) risk always be my companion ..
one thing i'm curious about..if i want to upgrade to any other roms, should i upgarde my IPL 1st?..just like i try to use your personal crystal rom..why didnt i make it well, even though i follow the instruction step by step?
After i using those Korand's rom..everything is fine except my battery !!
i charging it & i notice that my device is getting hot !!..
i know this is not well..so i need to upgrade into others roms which more suitable with my device..
Thanks hma4 for your concern
___________________
HTC Dopod 818 pro
yup..better dont disturb the IPL
on second thought,it wisely not to disturb the IPL as you've mention except for those a genius
bout the battery,after few reset.. it back to normal..no hot anymore
i think i better stick with this rom for awhile.. as it is nice,stable & fast..+ more xtra storage..
In general, just leave IPL and SPL alone. Most ROMs (except WM5) work regardless of IPL/SPL and it's better to avoid bricking/damage.
Can anyone please post a guide on how to flash Hard-SPL onto my HTC TYTN.
The guide for installing Hard-SPL onto the HERMES is not available anymore, and i am EXTREMELY confused about what im doing, and i am afraid i will brick my phone if i do something wrong.
Please please please help!
Read the sticky, first post on this page.
It really isn't hard to do. But be sure you know what you are doing btw. SO read the sticky!
Basically you just download the flavor of Hard SPL you want (I used 2.10 which I can recommend, very easy to downgrade to factory SPL again as I just learned!).
After download unzip the folder and run the RUUWrapper. Follow instructions exactly, do nout unplug your device etc. and it should work like a charm. It takes about 1 minute!
If you don't know what you are doing or you are still doubting, wait for Mr Vanx site to come online again or don't flash. There is always a risk you screw up and end with a $500 brick.
So use at your own risk!
Download hard spl v7 from
http://forum.xda-developers.com/showthread.php?t=296722
thanks guys i did it
hi guys have tried to update mine today on a jasjam it connects sys it updating but starts at 0% then just jumps to 100% and says flash finished but when i restart the phone it still has the same loader what am i doing wrong i want to update it from windows 5 to windows 6 using crc-9 but don't want to update till i do the loader any help from you guys would be great
cheers puca
puca said:
hi guys have tried to update mine today on a jasjam it connects sys it updating but starts at 0% then just jumps to 100% and says flash finished but when i restart the phone it still has the same loader what am i doing wrong i want to update it from windows 5 to windows 6 using crc-9 but don't want to update till i do the loader any help from you guys would be great
cheers puca
Click to expand...
Click to collapse
start the device in bootloader, what is displayed?
Mine is doing the exact same thing. Starts at 0% and jumps to 100% and says it is done, but it has done nothing.
Rockford_622 said:
Mine is doing the exact same thing. Starts at 0% and jumps to 100% and says it is done, but it has done nothing.
Click to expand...
Click to collapse
the SPL flash is VERY quick.
I'll ask YOU this aswell, put your device into bootloader mode and tell us what it says.
hi mrvanx
thanks for your reply after checking the bootloader it has changed to 2.10 olie it did it so fast i thought it had failed will check properly next time and have successfully flashed it to crc 9 and it runs great thanks for all the help
mrvanx said:
the SPL flash is VERY quick.
I'll ask YOU this aswell, put your device into bootloader mode and tell us what it says.
Click to expand...
Click to collapse
I appreciate your reply Mr. Vanx. Same as with puca, I put my phone into the bootloader mode and it does indeed show the correct 2.10 Olipro version. This is the 3rd 8525 I have had and I could have SWORN it took much longer on the first 2. Even the update from WM5 to WM6 seemed to take much less time with this particular phone. Guess I shouldn't really complain
Downgrade Error 260
Hi Mr Vanx I have followed your guide to downgrade my current SSPL (2.10 Olipro) to SSPL (1.11). But I keep getting error 260. I have followed guide step by step.
I have even tried flashing from SD-Card (by renaming to HERMING.nbh). Process runs successfully, but nothing happens.
Its still showing SSPL-2.10 Olipro in bootloader. Am I missing anything?
Thanks
can some one point me to the guide. I am facing a NO GSM problem on vodafone VPA 1605 with following config:
ROM Version: 1.20.161.6
Radio: 1.03.06.00
CID: VODAP001
Bootloader: 1.04
I do not see the radio version or the IMEI. So I would like to do a HARDSPLv7 followed by Radio ROM update to 1.06.00.10. I hope this will work. Seniors may help with their sggestion.
Can someone help me with the guide to HARDSPL as I am doing it for the first time and the guides are not available at MR Vanx site nor can I locate the sticky?
regards,
H
have you read the first page?
cant uprade from spl 1.40 to 2.04
am using hermes 300 and i want to uprade from 1.40 t o 2.40 but i cant do it.i ve tried can anyone help
dania
How to hard reset without win
hi
I have an I-mate 9502 but my problem is for pocket pc generaly.
I installed a program for sound, When I do a soft reset it hangs on Blue Imate page and didn't boot.
I tried to hard reset but it dosen't worked too(I know hard reset of it, is Green+FN+Power button) but it don't work, Also I tried to install a fresh Rom but it need to loud windows.
Please help how to hard reset it.
thanks
majida said:
hi
I have an I-mate 9502 but my problem is for pocket pc generaly.
I installed a program for sound, When I do a soft reset it hangs on Blue Imate page and didn't boot.
I tried to hard reset but it dosen't worked too(I know hard reset of it, is Green+FN+Power button) but it don't work, Also I tried to install a fresh Rom but it need to loud windows.
Please help how to hard reset it.
thanks
Click to expand...
Click to collapse
you should try the hard reset iMate 9502 posts by martin_yo in http://forum.xda-developers.com/showthread.php?t=407336&page=2
Code:
After Flashed with the new ROM, My Device is now stuck in iMate Blue Screen Logo....!!!
But Don't worry Guys...it can be solved with manually hard Reset...
1. Remove battery and reinsert (to make sure the phone is off).
2. Hold down Fn and the Green button (with the phone icon on it) and press the power button.
3. You will see the white hard reset option screen almost immediately. Press the Left Soft Key to hard reset.
Work for me...
but !!
With many thanks Hakim
But I know hard reset of my phone, I did it many time before, unfortunately it dosen't work this time. I tried all I knew about hard reset. but I couldn't do anything for my phone.
I tried (FN+Green+power like last time I did hard reset easy)(FN+Green+reset button)It don't sho any reaction.
Please help me.
hi all, hope someone can help, been reading threads for days and this is about my fifth xda so i'm no newb.
it's an i-mate jamin i got for my father, ipl/spl 2.13.0001 (G4) bought second hand from ebay, seems to work fine running wm5 os 2.13 but won't send text messages, didn't think much of it since i was planning to upgrade to wm6.1, unfortunately NO KNOWN METHOD WORKS.
Here's what i've tried:
Two different windows xp computers, two different cables, re-install activesync, hard reset, multiple connection retries.
PDAViet temp step 1 from OS and Bootload, most common error is [264], tried NVID wm5, tried official IPL 2.20.0001 upgrade and official i-mate ROM, tried jump/soft/hard SPL, all go to white bootload screen but no further, sometimes the green LED will flash as a radio signal on this white screen but usually nothing.
It seems very much to me like the bootloader is not responding, can someone please tell me when you put the phone in the bootloader and plug the usb cable in, after it has said USB, if you then unplug the cable should the USB text dissapear? because on mine it remains..
when running hardspl.bat the only error on the script is;
cerun: program could not execute (0), after trying to run jumpspl, altho it DOES go into the white screen and just sit there, yes i've tried pressing the camera button.
I'm fresh out of ideas here! help please!
when i run Prophet_G4_IPL_v2.20.0001.exe after a hard reset (sticks on bootloader and give [264]) but before that it says upgrade from 1.2.0.0 to 2.20.
That first number doesn't seem right? is it possible the previous owner flashed a G4 ipl onto a G3 device? and how would I tell?
Hi everyone.
I tried to upgrade my i-mate Jamin to WM 6.5 using this file.
I think I did everything right (I checked the G4 and HardSPL in the beginning of installation and I'm sure my MB is G4).
Everything was going perfect and the installation advanced without any problems, but at the end my Jamin was stuck in the three color screen, showing only the following words:
IPL: 2.13.001
SPL: 2.13.001
I tried to hold the Comm Manager and Soft Reset buttons as this topic recommends, but the phone gets back to the 3 color screen again, and no success...
I tried to pull out and reinsert the battery, also no success...
Please help me, this is my friend's phone! I AM SO NERVOUS and I may kill somebody!
Is there anything I can do to get rid of the 3 color screen?
mahi58 said:
Hi everyone.
I tried to upgrade my i-mate Jamin to WM 6.5 using this file.
I think I did everything right (I checked the G4 and HardSPL in the beginning of installation and I'm sure my MB is G4).
Everything was going perfect and the installation advanced without any problems, but at the end my Jamin was stuck in the three color screen, showing only the following words:
IPL: 2.13.001
SPL: 2.13.001
I tried to hold the Comm Manager and Soft Reset buttons as this topic recommends, but the phone gets back to the 3 color screen again, and no success...
I tried to pull out and reinsert the battery, also no success...
Please help me, this is my friend's phone! I AM SO NERVOUS and I may kill somebody!
Is there anything I can do to get rid of the 3 color screen?
Click to expand...
Click to collapse
Please don't panic! If you see when connect the phone to the computer and USB message on the bottom of prophet screen update is posible. So try to put original WM5 on the phone. Read dioxda2 post for more. For sure you don't hardspl your phone before flashing....
Thanks
bikertibi said:
Please don't panic! If you see when connect the phone to the computer and USB message on the bottom of prophet screen update is posible. So try to put original WM5 on the phone. Read dioxda2 post for more. For sure you don't hardspl your phone before flashing....
Click to expand...
Click to collapse
Thank you very much, my problem solved using the WM5 flashing process.
I thought it's impossible to get the phone connected to PC because activesync wasn't establishing a connection to the phone, but obviously I was wrong.
After flashing WM5, I performed a HSPL on the phone, and then used the file again, and the phone was upgraded to WM 6.5 with no problem.
I previously had downloaded your 6.5 ROM from a crappy forum, which was only including a download link and some useless info, and since I was a newbie myself D), I didn't even know that I should have performed a HSPL before upgrading the OS.