I tried to unlock Hermes Orange SPV M3100 withe the latest unlocker v3a but couldn't unlock...After run auto unlock v3a, and run hermes unlock at the end, it says unlock successfuly but the phone still asks to enter unlocking code..i've been reading the hernes unlock threads but could find the solution to unlock it..this hermes has ipl 1.01 and spl 1.40 0ipro...anyone knows the way to unlock please help..thanks
sorry..problem solved, phone's unlocked...don't know what happened first but after hard reset phone, insert original sim and repeat procedure, phone is unlocked after that.
hi, i have the same problem. When i m flashing with Auto_unlock_3a_pof , i must insert original sim (orange) or no?
thanks
hi, I had the same problem. the unlocker went thru the procedure as successful, but was still locked to orange and asked for the code.
I had ran it without any sim.
after I did a hard reset and put in an orange sim, then ran it. it was ok.
unlocked. thanks.
you gotta give LOTS of details about your problem. there are literally hundreds of possibilities if you give us no details about what you did, what went wrong, during what stage... have u set up correctly, did you flash hardspl, was your battery full, did you read instructions well or just skim and jump ahead?
i hav same problem...."--------------------------------------------------------------------------------
I tried to unlock Hermes Orange SPV M3100 withe the latest unlocker v3a but couldn't unlock...After run auto unlock v3a, and run hermes unlock at the end, it says unlock successfuly but the phone still asks to enter unlocking code..i've been reading the hernes unlock threads but could find the solution to unlock it..this hermes has ipl 1.01 and spl 1.40 0ipro...anyone knows the way to unlock please help..thanks""" plz help me
Related
Hi
Im hopeing someone can help me I know this issue has probably been discussed loads of times and im a muppet for doing it, I was looking at different ROM's for my Orange M3100 and thought I would go for the IMATE JASJAM ROM so I could get MSN messenger .... I unfortunatly selected the TELSTRA 1.06 Bootloader ROM and downloaded instead of the 1.04 ( I should have read the posts on this ROM before!). Now I am stuck in bootloader 1.06 and as I have read the only way to get back to 1.04 is to flash with a ROM that is the same as my carrier (Orange UK).... the only Orange ROM is the Romanian one thats just been put on the WIKI, I have tried with this but its coming up Vendor ID error... if anyone can help or tell me how I can go back to 1.04 id be grateful? if not do I just have to wait until orange UK bring out a ROM with bootloader 1.06 ????
Thanks a lot ! James UK
Same problem with Cingular bootloader 1.06
I've the same problem with Cingular 1.34 bootloader 1.06, I try to downgrade with same bios CID (CWS__001 as I read on this forum) to bootloader 1.06 but I receive an error "WRONG VENDER ID" (also if i leave connected my PDA and I restart RUU utility it give me the same error)
I've also tried to install another vendor bios with bootloader 1.06 as suggested but I receive the same error message!!!
Emanuele
Unfortunately, you're stuck unless you either a) wait for a bootloader for your CID or b) pay the $38 to do the super-CID unlock. There's a thread on that stickied, so if you decide to do it, help them out by doing the usb capture.
Thanks... I have already unlocked the device with IMEI-Check.co.uk do you mean this? If I have unlocked it then do you think I should run IMEI check again on the device and it may unlock the CID ? cheers, James
If you run the imei tool again (with the latest version of theire software) it will reverse your bootloader to 1.04 and make your device super CID
I've searched and searched the fourms but could not find any answers.... I have a Cingular 8525, i'm trying to unlock it etc.. but when I start it up, it does not show me the IBL or the SBL.... so I can't determine which version of the bootloader I have. Any ideas? My screen shows up with a 3G Cingular flame and then... like some letters and numbers... any help would be nice. Thanks.
Read the Part about Entering Bootloader Mode, should be SPL you are looking for.
Free HTC Hermes SIM & CID Unlocker Available (v2a)
Frequently Asked Questions:
Q - How do I know my bootloader version?
A - When you are on the tri-color screen check the number after SPL-X.XX
you need to go into bootloader mode. Search for it, or it could be in the WiKi. I think you hold the OK button and the Power button and soft reset it with the stylus.
If it's a stock 8525 you have bootloader 1.06 and need to load the 1.30 Cingular ROM to get bootloader 1.04. From there you can do the rest of the steps to unlock and SuperCID.
You guys are great. Thanks sooo much.
Hey all,
I've tried to search for an answer, so if I've missed something obvious, please don't chew my head off, but I recently used pof's SIM unlock v3a program on my 8525 and afterwards when I went to flash it with a new radio, it stayed on the bootloader screen for a while and then said "Error 260 (Upgrade Error)” and won’t flash. After SIM unlocking, my bootloader screen reads
HERM100
IPL-SSPL by Des
HERM100
SPL-1.09.ds
Can anyone help me out here? I've written in the SIM/CID unlock thread and PM'ed pof, but no one will answer. I really need to upgrade this week.
Edit: Tried it on a Windows XP machine and it works. Any idea why it won't work on Vista like it did before?
I was trying to sim unlock my friend softbank X01HT
so i was running the greatest pof unlocker v3
and it was successful (unlock cid and sim)
but after a reset the X01HT showing USIM window
and asked to input a code.
in the faq,pof suggest to update the rom to english one or to use the uk unlocker until it ask for unl files. so take the second suggestion and use the uk unlocker.
the usim are not showing anymore but my signal are not showing also.
only a ! icon in my signal bar
already tried to using the unlocker a couple times and the result it the same
and pof say maybe your device was pre april and it cannot be unlocked for a moment
and pof say to use mtty to check the bootloader radio version.
so help me answer this question please
1. why in mtty are not showing "usb>>" but only "cmd"
i tried to type "rtask a" but its say command error. i already disable the usb in active sync and connect to usb in mtty. tried also in another comp but still not showing the "usb>>" after i click enter twice.
2. is there any other method to check my x01ht was have the protection unlock or not ??
thx
the spec are here
X01HT HERM200
Black
IPL-1.01
SPL 1.40.Olipro (i upgraded it to 2.10.Olipro)
M 05,S 04,B 06, D. 1.33,
R 1.14.01.10,
G 32.50.7018.00H
Read the past forums about post April X01HT
Can you read some past forums about X01HT, post april so you can understand how to unlock it,so in your case, 1.14.01.10 radio is not possible yet to sim-unlock, but my friend here transfer the old hermes (X01HT signal IC) to the not unlockable one, it is a success after sim unlock it, the problem is where to get some hardware (Signal IC's) for X01HT.
Good Luck, try the hardware radio transfer then unlock.
HTC Herald Unlock
if you live in Bali - Indonesia you can bring it to me. but sorry its not free...
dvaiyo said:
if you live in Bali - Indonesia you can bring it to me. but sorry its not free...
Click to expand...
Click to collapse
i live in bali where you honey.... hehehe
after reading the threads, wiki etc, still i aint able to find a solution. so tried opening up a thread.
well my question is the supercid and sim unlocker v3 by pof on this site requires one to have the spl1.04 ( A MUST ). now if someone, for example, me, has hardspl2.10olipro and would like to unlock the sim, then
1) should i downgrade(or not) to 1.04? if yes, how? or should i run it as such?
2) is there any other better, safer and quicker way than pof's to have sim unlocked?
currently i have
O2 xda trion (herm100)
rom: halloween rom by josh
radio: 1.47.00.00
ipl: 1.04
spl: hardspl2.10olipro
PLZZZZZZZZZZZ DO HELP
Use Pof's tool then re-install Hard SPL V7. You have to downgrade the SPL to sim unlock... Or you can pay to get it done...
thanx for the clarification
now a step forward
so i have to downgrade. the mrvanx guide at mrvanx.org which is i reckon the best guide, has a guide to know how i do it but the spl version 1.04 doesnt download and says that file not found. u may try for urself http://www.mrvanx.org/files/HERM_SPL_1.04_CUSTOMRUU.rar
so really cant head this way.
will u, ultramag69 or anybody else provide me with the file or working link to the file.
anticipating help
Download this - ftp://xda:[email protected]/Hermes/Tools_and_Programs/HTC_Hermes_SIM_CID_Unlock_v3a.zip
Just run the .exe's. IPL doesn't matter, its the SPL that needs downgrading...
Cheers...
i think i aint getting my point clear enough. my point is that now i have to downgrade as i should not ( or should i ??? ) run the unlocker tool on spl2.10olipro. so for downgrading to spl1.04, i need spl1.04 so that i follow the downgrading procedure. now, i cant find out where should i get this from? the mrvanx.org htc guide has the procedure and the spl but the link to download spl1.04 isnt working and gives me error 404 i,e file not found.
hope i'm clear enough this time and hope u know the way out,
thank u
I also had upgraded to SPL 2.10. You need an SPL 1.40 or less. The link I gave you will downgrade the SPL to this. You can then run the unlock tool successfully. Worked for me.
You may need to run the sim unlocker twice for it to work, there were reports it didn't work properly the first time.
Remember to re-install Hard SPL V7 afterwards... Even if you supercid your device, the benefits Hard SPL give in recovery if something goes wrong is worth it.
Cheers...
still not there
havent unlocked yet. may b i am missing something. i let u know how i try unlocking,
before starting my was 2.10olipro and after i used ur provided link its 1.40olipro ( NOT 1.04 ). afterwards i tried the unlocker tool, ran the manual way as the automatic didnt work for me as i followed everything but nothing happened to the phone i,e no bootscreen, no flashing etc nothing at all.
the manual way was to transfer SSPL/SSPL-HERM.exe to phone and run, tricolor screen appeared this time with different spl than before, then i ran RUU/RUU_HERM_Unlock_v3a.exe and followed flashing. went fine. allowed to reboot.
then transfered HERM_Unlock_v3.exe to phone and ran it. unlock options, sim and cid unlock, ran, process completed, shut down the phone, wait for 10 secs or so, restart the phone
change the sim,,,,,,,,,,,,,,, no sim detected.
i tried this so many time
plz help
Run sim unlocker tool on phone by itself. try 2 times then try new sim.
Don't forget to update your SPL back to Hard SPL V7.
thanx for replying but doing it two times didnt work either.
any other way out?
at last worked out for me.
thanx a lot to ultramag69
i just ran the unlocker innumerable times, but whenever i would change the sim it wont work fine. then just by chance i started playing aroung with the phone and went to the sim programmer ( not the sim manager but the one that is specific for every sim, in programs menu ) and selected couple of services which i thought wont take place, but after a while the signal started appearing and everything was fine then.
now everytime that sim is inserted i have to go through this small exercise but i'll take it, no problem.
glad it happened
thanx to all the members of xda
especially to ultramag69