Related
Hi all,
I need an advice from you guys please:
My Topaz is not turning on, it simply does not do anything.
Last time I wanted to change the language but my battery was not fully charged, so in the process it suddenly turned off and since that time I am not able to turn it on, does not display nothing on screen when I press the on button it just vibrates continuously and not stop, and that´s it...
The charging light was on the 1st time I tried, but not the second time.
It is SIM unlocked but not hardspl´ed
Any advice would be great!
Thanks in advance
UPDATE 13-Mar-10
Today, I connected Topaz to wall charger, amber led turned for about 10 sec, then turns of, then vibrates, then nothing again.
I tried to do hard reset, nothing happened, then after some minutes the device is short vibrating every 1 min aprox, no led on, still can´t do nothing more.
EDIT: After 15 min of short vibrating every 1 min, now it´s completely dead again........
Thanks for reading,
Can you put it in bootloader? Is a hardreset possible?
Try to turn the phone off, remove battery, and insert it again. Then hold vol down and press power. Do you get red/green/blue (or whatever) colors?
If you do. let it boot until it says USB (perhaps need to connect usb to PC for it to change from serial to usb) and after that just run the topaz ruu and it should flash.
If you dont get it to start to 3 color screen try and hold up+down and press power.
yes, Vol down and powerbutton. should boot to serial/usb flash screen.
Thanks guys for your reply
Soon as I get home I´ll try and report back
Cheers,
Flash a stock ROM
jmkhenka said:
Try to turn the phone off, remove battery, and insert it again. Then hold vol down and press power. Do you get red/green/blue (or whatever) colors?
If you do. let it boot until it says USB (perhaps need to connect usb to PC for it to change from serial to usb) and after that just run the topaz ruu and it should flash.
If you dont get it to start to 3 color screen try and hold up+down and press power.
Click to expand...
Click to collapse
Hi
Just check that if you try to reflash the ROM whether you should use a stock ROM vs modified ROM as you wrote that you do not have HardSPL on your Topaz.
Once you have successfully reflashed using stock ROM do a hard reset and then install HardSPL 1.83.
Good luck
Aussie
Still need help!!
Ok guys,
Let me explain you what happened:
None of the instructions above worked...
Can´t put on bootloader, hard reset nothing happens
When connected to wall charger amber led is on, if I press power button led turns off and vibrates, then led turns on again but nothing else happens.
Pressed down vol and power = Nothing happens
Pressed up/down vol and power = nothing happens
EDIT: Connected to PC and automatuically installed a qualcomm driver not detected also by WMDC
Disconnected from PC then connected again to wall charger and now amber led not turns on....
Please help!!
Any other advice please!
I really don´t know what else to do
Thanks in advance for taking your time on this thread
Per your PM, I'll certainly help you if I can.
Do you happen to know what caused it to brick? This will help determine how to bring it back. Did you attempt to flash a custom ROM w/o HSPL?
I am not an expert on this but have seen some chefs claim they can bring back a bricked device.
There is a program called MTTY that can usually get your phone to connect to your PC and there are functions to run in that program that can get it to a flashable state so you can reflash your shipped ROM.
Also search the Wiki for restoring bricked device, regardless of the model, it should be the same process. I think I have seen this in the Tilt(Kaiser) forum and maybe in the Fuze (Raphael) forum.
I haven't used this program in a while so I forget the commands but you should be able to find them in a search.
In the meantime I'll do a little research too and see what I can find out.
The main thing we need to accomplish is getting you back into bootloader mode.
1. Here is a link for recovering a Hermes and it has info on mtty.
Thanks a lot Bruce,
I have the original ROM and my Topaz is the unbranded model.
I was just trying to change language but battery was too low, then it turned of and you know the rest of the story.
I have it SIM unlocked but not hardspl´ed and I was not doing any ROM upgrade or so...
I´ll try to use MTTY and find about your recommendations, later report back.
I appreciate a lot your reply!
Cheers,
EDIT: Tested MTTY but in some point says "power on the unit " but that is what I can´t do, nothing happens
Will continue testing and searching...
This is from the Wiki. It may help. Says to use PUTTY instead of MTTY... with instructions.
Another thread on recovering device.
Bruce Inman said:
This is from the Wiki. It may help. Says to use PUTTY instead of MTTY... with instructions.
Another thread on recovering device.
Click to expand...
Click to collapse
Thanks Bruce,
I went through both links but nothing...
The main prob is that I can´t even make it turn on...
Now when wall charger is plugged I do not have the charging led on, so I am really lost...
I do not have another battery to test but I don´t think is that because Topaz is almost new!
But Now I think it´s not charging the battery...
Hope any other idea can save me
If it is almost new try to send it to warranty!if it has the original hspl no prob then!is better then trying to reapair youself, with the cost of loosing warranty!
Good luck with that!!!
Thanks, but I do not have that option
I have high hopes with all the great team of XDA!
first thing first,you have to have power in your phone.....borrow the battery from someone or recharge your battery in somebody else's phone.......then try to go in to bootloader mode (volume button down and power button)..........
komsa said:
first thing first,you have to have power in your phone.....borrow the battery from someone or recharge your battery in somebody else's phone.......then try to go in to bootloader mode (volume button down and power button)..........
Click to expand...
Click to collapse
Yep!
I ordered today another battery
Soon as I get it will report back.
Thanks,
Maybe this will help
It happened to me once. Nothing seemed to work. What did work, I left the phone charging for a day. First take ou the battery for at least a minute. Put it back on. Then connect the wall charger to the phone and let it charge. Hope this will help.
When it happened to me the LED wasn't working either, just connect the charger and let it charge.
Thanks,
I done that yesterday and left it all night but nothing...
I really hope is a battery problem, I´ll find out soon as I receive my new one
wrong place
Exactly samething happened to me.. the only difference was that I was using google maps and connected to my car charger. It somehow didn't charge and ran out of power and kept restarting whenever I tried to charge from a wall-socket.
This is what i did... worked for me.
Take out the battery from the back
Hold down the power button for at least 30 seconds to drain out the static charge.
Take out the sim
Plug in the USB to the phone (without the battery and without the sim)
With the phone connected, press the Red button at the back (soft reset)
Unplug the phone from the charger
Put the battery back in
Connect the USB to charge
Cross your fingers and say a lil prayer
Wait for 30 minutes
Turn it back on.
Lemme know how that goes 4 u
Thanks
I done all your procedure but after this point: [*]Connect the USB to charge
Led charging light did not turned on...
By now my only chance is to test with a new battery (which I will receive on thursday), but I do not have too many hopes as the device is almost new
I´ll report back on friday.
Thanks to all and I will be happy to receive any other suggestion
Ok, a bit akward. I think i bricked my folio 100. I was working on upgrading to honycomb, i did some things wrong i think. Problem is now when i boot the screen stays black and only the power led goes on. Any idea where i shuld search to try and get it back to live?
if you can boot into fastboot you might be able to save your devise by pushing the revovery and rom to ur devise
I cant get into fastboot, i dont even get the toshiba logo.
shidima_101 said:
I cant get into fastboot, i dont even get the toshiba logo.
Click to expand...
Click to collapse
Did you try to connect to fastboot? Maybe your screen is broken (or if you are lucky the screen connector is loose). Does it vibrate when you turn it on?
It is very improbable to brick this device by flashing something. At least I never heard of it. Only thing known to me to fully brick your folio is by pressing 4x Power and volume down on boot (don't try that...).
When i press the power button it does nothing, only the power led on the right turns green (white when on AC ).
Also, when i connect it to usb and do a fastboot devices i get no respons. Realy think i did something wrong and bricked it :S
mblaster said:
Did you try to connect to fastboot? Maybe your screen is broken (or if you are lucky the screen connector is loose). Does it vibrate when you turn it on?
It is very improbable to brick this device by flashing something. At least I never heard of it. Only thing known to me to fully brick your folio is by pressing 4x Power and volume down on boot (don't try that...).
Click to expand...
Click to collapse
i tried a lot of things in this folio 100 forum except 4x power down.. really feel like trying it..
shidima_101 said:
When i press the power button it does nothing, only the power led on the right turns green (white when on AC ).
Also, when i connect it to usb and do a fastboot devices i get no respons. Realy think i did something wrong and bricked it :S
Click to expand...
Click to collapse
did u try removing the battery?.. or maybe the reset pinhole at the back?.. who knows it might work..
I brick my Folio too, and now it don't have logo when power on.
I tried to get battery off and press the reset on the back, and nothing happened.
How to rescue a fully brick folio?
mblaster said:
Did you try to connect to fastboot? Maybe your screen is broken (or if you are lucky the screen connector is loose). Does it vibrate when you turn it on?
It is very improbable to brick this device by flashing something. At least I never heard of it. Only thing known to me to fully brick your folio is by pressing 4x Power and volume down on boot (don't try that...).
Click to expand...
Click to collapse
apologize for interfering & oftop, but certainly cant keep silence - "impossible to brick" - same i was told abt my dell streak device, but here I'm with bricked device on hands, where only ORT-JTAG can help :-(
it was bricked when PC hanged during rom flashing....so I guess every chance is possible :-(
Shidima_101 can you describe in detail before/during brick ?
Well, I'm not really sure what i did. And i think that is the problem. I was installing a new rom, and left it unattended. When I came back, something was wrong and I started messing with some options. Witch turned out to be wrong i guess
Tho I'm a little further now. When I connect the tablet I my pc recognizes its there a device, but I'm not sure I can get it working again. Tomorrow I have some time to look at it more.
Sader0 can you give me some info on ORT-JTAG? Do you know if its possible to do this on the Folio100 ? I don't mind opening up the tablet to get it back in to working order.
I'm in the same situation.
After the update to the last version, my folio apparently boot but the screen is blank. The backlight is on but nothing appears on the screen.
I'm able to go in Fastboot or in recovery mode, but formatting cache. system and reflashing different roms do not solve the issue
What I should do ?
SOLVED !
Read this:
http://forum.xda-developers.com/showthread.php?p=14625817#post14625817
Not sure if I can even get to fastboot, but ill give it a try tomorrow. Im at my work now and didnt bring the tablet
bricked
I ****ed up? 4x power button, Ar there solutions?
gtrz
Ok, I have a small update. After trying a lot of different stuff, and nothing working, I decided to bring my tablet back to the store. First I tried to get them to switch my device for a new one, but that was a no go. So the device was returned to Toshiba for a check up and fix.
I was a little afraid that they would find out that i rooted and bricked my device, but today I got a letter telling me I can come pick it up and it was fixed free of charge
So tomorrow I'm going back to pick up my tablet
Hi all,
yesterday I used an emergency method for the second time which saved my phone even when SEUS doesn't respond. Please note:
1. This is an emergency method, if ALL other methods fail. If you are not comfortable with this, then don't do it.
2. I don't know if this works for the new Mini or either Pros.
3. You can damage your phone if you do this incorrectly, so take care, and you do this at your own risk.
4. If you are still in warranty, this can void your warranty if they detect what you've done.
5. If you're VERY new to all this phone modification stuff, you probably shouldn't do this. But, if you are new and all other methods don't work, then you can try this if you don't want to/can't afford to send away to repair.
Still in trouble? This is ESPECIALLY useful if your phone won't switch on, SEUS won't detect it and charging doesn't show LED. Do this:
1. Take off the back cover.
2. To the left of the camer lens is a rubber part covering the phone. At first, it looks like it won't move, but use something small and thin (like a pin or tack) to gently lift that up, and take it away. You need this so keep it.
3. Inside you will see a small white connector. This connects the battery to the rest of the phone. Use a tack or pin to gently pull back on the white part. When it does get loose, lift up.
4. After a few seconds, put that white connector back. I do it by laying it down and pushing in with the pin/tack, and push down. You must hear it click. Be very, very careful with this, it's delicate!
5. Put back the rubber connector and case.
Try switch on your phone now. Twice, this has helped me when ALL else failed...
**When you take off the rubber cover to the left of the lens, you will see this white tab as you can see in this picture. You use a pin/tack to drag that back, then press down again and push it into the phone to reconnect. This resets it.**
I have used this on the 2010 Mini, and I don't know about the 2011 Mini or either pros...
phoneyericsson said:
Hi all,
yesterday I used an emergency method for the second time which saved my phone even when SEUS doesn't respond. Please note:
[...]
Try switch on your phone now. Twice, this has helped me when ALL else failed...
Click to expand...
Click to collapse
can i add a link to this in my FAQ?
Thanks for the recovery solution!
Will check this method if my mini dont respond in future
Sent from my X10miniCM 2.1.1
matmutant said:
can i add a link to this in my FAQ?
Click to expand...
Click to collapse
Sure!
Honestly, this method has worked twice now (only needed it twice) and if the phone doesn't switch on, PC/laptop/SEUS don't detect it/no LED or anything...this STILL works...! It's a kind of hard reset we need, if soft reset (home and power) don't work.
can anyone confirm whether this works on the pro yet ?
tomvanoppens said:
can anyone confirm whether this works on the pro yet ?
Click to expand...
Click to collapse
If I understand it, this disconnects the battery from the phone. On the mini-pro you can just pull the battery.
Sent from my U20i using Tapatalk
Yes, that's right ^^ on the Mini of 2010 you cannot disconnect the battery like normal. This is how you can do it, and it really does fix many of the worst kinds of problems...it re-starts the connection of the phone.
Still not working ;(
i tried this method twice, and nothing happened...
my phone was working fine yesterday, woke up, found it turned off.
i tried to charge it, and it showed no signs of charging, no LED lights, no heat, nothing.
i tried to restart it using the power+home+back buttons, i tried to get it on flash mode, nothing worked.
its still off and NOT charging even though its been connected to the charger for like 2 hrs
anymore ideas?
Hi buddy.
There's something different with these smartphones. This happened to my Mini also. I contacted Sony Eric. and they said make sure your battery doesn't die completely. You must leave it charging in the wall for about 2 hours and wait for an LED (green) to show. If that doesn't work, then I'd try SEUS and repair the phone. If that doesn't work, then I'd try this solution. It really should be the LAST thing you do - if you're not very familiar with this you can break it.
And you tried this method and it did nothing? Really? You disconnected the white wire, waited 10 seconds and reconnected? Then I'd try charging for 2 hours WITHOUT trying to turn it on.
help me plzzzzzzzzzz
Hi!
can anyone help me!
i treied to root my x10 mini pro and something fail
Idont know what happen but i fowlloed the guid but i know that was my wrong i dont know what happend.
My x10 mini pro are breaked now when i try to turn it on it came just SONEY ERICSSON just it, itreied to uppdate by pc.companion but i could not uppdate it becuse the program didnot finde the device.
Can someone help me please.
Tanks!
That is common and you should be able to fix it. If all you did was try to root it, I'm not quite sure what failed. This happens sometimes if you try to put a new operating system (ROM) on the device but something goes wrong.
And PC companion doesn't detect your device?
If not...there is another Sony Ericsson program called SEUS (Sony Ericsson Update Companion). Use that instead and tell it to repair your phone. To do so, you connect your phone to the PC, press the power button at the top of the phone AND the middle (menu) button on the front together...then your phone resets. If you have SEUS ready, it will connect your phone, your phone won't boot, SEUS will repair it. The light at the top of the phone will be green if this is working correctly.
Hi, i just bought bricked x10 mini for 20 bucks. I has no sign of life, no led indicator, etc. It's not detected by seus. I also disassembly it to check physical damage( i didn't find any damages).
Phone just won't turn on. Lets check if 2hours charging is working for my case.
Yes, try the charging thing. Sony Ericsson told me to do this by email. I had no idea that smartphones worked like that, but yes. It could have life but not show for 2 hours of charging. (They said DON'T try to turn on the phone while it's trying to charge in this case).
If none of that works then try more extreme methods, like the one I mention with the white cable.
Good luck!
still no luck with charging solution. actualy i've disassembly it so practically i have done your solution. i will go check more deeper about the problem. the worst case is IC failure.
Thank you for the tip phoneyericsson!
I didn't find it hard to do -- I pulled off the ruber thing with a nail, and tweaked out the plug with some small scissors.
I was stuck at the SE logo, and couldn't turn of my phone or enter CWR. I wanted to set it back to standard using SEUS. Instead of using the method mentioned in option 2 here, I simply pulled the white plug to the battery, which turned of the phone. Then I inserted it again and the phone stayed off. Then I simply did as SEUS asked, and now I'm back running, ready to get CMmini on my device again!
That's great to hear! ^^
Hello everyone,
I was wondering if I could pick your brains.
I have recently acquired an Xperia Ray that does't work, I was told that it had been dropped and the battery contacts were faulty.
I then preceded to take the phone apart to investigate and found nothing physically wrong inside.
The phone doesn't seem to be charging at all, When I remove the battery and press an hold the power button I get a vibrate.
Again, Removing battery and replacing, pressing and holding the power button and volume down gives a green light and vibrate.
Finally, As above bet pressing and holding the power and up volumes gives a blue light and vibrate.
I don't know any history of the phone I don't know the legitimacy of the "phone dropped" story, physically the phone is immaculate.
After some extensive googling I'm starting to think maybe a bad flash could be the culprit?
Thanks for reading.
Dave
davelee1097 said:
Hello everyone,
I was wondering if I could pick your brains.
I have recently acquired an Xperia Ray that does't work, I was told that it had been dropped and the battery contacts were faulty.
I then preceded to take the phone apart to investigate and found nothing physically wrong inside.
The phone doesn't seem to be charging at all, When I remove the battery and press an hold the power button I get a vibrate.
Again, Removing battery and replacing, pressing and holding the power button and volume down gives a green light and vibrate.
Finally, As above bet pressing and holding the power and up volumes gives a blue light and vibrate.
I don't know any history of the phone I don't know the legitimacy of the "phone dropped" story, physically the phone is immaculate.
After some extensive googling I'm starting to think maybe a bad flash could be the culprit?
Thanks for reading.
Dave
Click to expand...
Click to collapse
Flash ftf with flash tool.
Hold home and volume up while connecting to PC with USB if led goes blue you can flash with flash tool
sent from my gorgeus Xperia Ray
might be lcd problem as well since it was dropped.
davelee1097 said:
Hello everyone,
I was wondering if I could pick your brains.
I have recently acquired an Xperia Ray that does't work, I was told that it had been dropped and the battery contacts were faulty.
I then preceded to take the phone apart to investigate and found nothing physically wrong inside.
The phone doesn't seem to be charging at all, When I remove the battery and press an hold the power button I get a vibrate.
Again, Removing battery and replacing, pressing and holding the power button and volume down gives a green light and vibrate.
Finally, As above bet pressing and holding the power and up volumes gives a blue light and vibrate.
I don't know any history of the phone I don't know the legitimacy of the "phone dropped" story, physically the phone is immaculate.
After some extensive googling I'm starting to think maybe a bad flash could be the culprit?
Thanks for reading.
Dave
Click to expand...
Click to collapse
use this guide,
http://forum.xda-developers.com/showthread.php?t=1126358
after u done that flash this http://forum.xda-developers.com/showthread.php?t=1316070 using flash tool let me know if it works if is a software problem works for sure!
Thnaks a lot for your replies guys!
I'm about to start Win7 installation on my MAcBook to try and get this tried. Hopefully it is a fixable software fault, If it is hardware would it display these traits?
again, thank you all very much.
davelee1097 said:
Thnaks a lot for your replies guys!
I'm about to start Win7 installation on my MAcBook to try and get this tried. Hopefully it is a fixable software fault, If it is hardware would it display these traits?
again, thank you all very much.
Click to expand...
Click to collapse
Just say if the phone turns on now is functional? what works? it might help another user!
Sent from my ST18i using XDA App
Nothing really works on it, It seems totally dead besides the vibrations and led indications. I do occasionally get 3 red flashed too.
Thanks
Hi,
I've plugged it in, got the solid green light but the PC doesn't recognise it or install drivers.
Do I need extra drivers?
When you install this Flash tool u get all the necessary drivers with it. They are located in the same folder. Unzip and install them when computer ask for them upon connecting it.
They don't seem do have the drivers for the Ray.
davelee1097 said:
They don't seem do have the drivers for the Ray.
Click to expand...
Click to collapse
Just use unzip "X10_ADB_drivers", it worked for me.
Just manage to unbrick my Ray
Just an Update on where I am,
I haven't been able to bootcamp my MacBook as DiskUtility won't let me partition the drive so have been borrowing Windows Machines.
Whenever I connect the device to the machine, windows detects new hardware then proceeds to start installing the driver only to fail and say that the "Unknown USB device malfunctioned". When I enter device manager and go to Unknown USB device and re-install the driver to the one I point it to windows informs me that the correct uptodate driver is installed.
I'm at a bit of a loss at where to go with this now, any help would be greatly appreciated.
Does anyone think that it could be a hardware fault?
have you installed PC Companion? the drivers for the Ray gets installed along with PC Companion
Hi,
My x10 mini pro started to act "funny" (restarting and shutting down by it self) so I found this forum. Kept reading a lot of posts for 6h until I decided to try flashing it with a costum rom to fix it.
Flashed via flashtool the Sony Style's 1.1 by paul-xxx; it worked for a while, then shut down again. But this time, with flashing red light (3 times, with hard-reset [home+power button] when trying to turn on and a looping red light (every 3~4 seconds) when trying to get to flash mode.
After some time, it vanished from existence and was presumed dead. No lights, nothing at all. Send to repair, they couldn't fix it, but they restored the lights (red loop again).
So, now it got dead again. I have two batteries, both charged, but still nothing.
I really don't know what to do. I thought it was HW damage, but the repair guy said it was software corruption.
So, any light on my head ? :/
Mazzocato said:
Hi,
My x10 mini pro started to act "funny" (restarting and shutting down by it self) so I found this forum. Kept reading a lot of posts for 6h until I decided to try flashing it with a costum rom to fix it.
Flashed via flashtool the Sony Style's 1.1 by paul-xxx; it worked for a while, then shut down again. But this time, with flashing red light (3 times, with hard-reset [home+power button] when trying to turn on and a looping red light (every 3~4 seconds) when trying to get to flash mode.
After some time, it vanished from existence and was presumed dead. No lights, nothing at all. Send to repair, they couldn't fix it, but they restored the lights (red loop again).
So, now it got dead again. I have two batteries, both charged, but still nothing.
I really don't know what to do. I thought it was HW damage, but the repair guy said it was software corruption.
So, any light on my head ? :/
Click to expand...
Click to collapse
If You're still able to enter into flash mode, try the SEUS restore.
http://forum.xda-developers.com/showpost.php?p=17458289&postcount=8
Then show it to Your repair guy...
Cheers,
M.
mum_laris said:
If You're still able to enter into flash mode, try the SEUS restore.
http://forum.xda-developers.com/showpost.php?p=17458289&postcount=8
Then show it to Your repair guy...
Cheers,
M.
Click to expand...
Click to collapse
No flash mode. That's my curse ç.ç
If I could just get it up, SEUS is waiting for it.
Mazzocato said:
No flash mode. That's my curse ç.ç
If I could just get it up, SEUS is waiting for it.
Click to expand...
Click to collapse
Dont know if it can help. .but give it a try with a new connecting wire.. maybe the connecting wire/port is damaged.. because it was the same with one of my friends.. he replaced with a new battery n a cord n it got fixed.. give it a try.. till then will search for u.. if found will post back..
Used a new one, from my girlfriend's 2011 mini pro, bought a new battery and fully charged on another phone. Still, no flash mode.
I would say that the port of the phone is out, but the repair guy used it with no problems... as he said.
The phone was hers, but she bought a new one. once this turned into a brick.
If I fix it, is mine... but, maybe there is no solution... :/
Just confirmed: Battery isn't the issue here. Recharged them to 100% and still the phone won't give a single sign of life.
Apparently, I'm doomed. I don't have money to buy fixing boxes and cables, but it really pains me out.
I already downloaded all the cooking material to start working on it, but... I guess it's dead.
As I searched, x10 mini pro doesn't have a test point, but a cable set up in the back board. But I couldn't find the schematics, just boxes... that will cost me a LOT.
I'll be watching the thread and test new options you guys give me... but that's all.
Sorry to bother you all with this issue..
Red light blinking again. 3 with home+power and constant bliking red connected to PC or trying flash mode. I'm confused now >_>
Mazzocato said:
Red light blinking again. 3 with home+power and constant bliking red connected to PC or trying flash mode. I'm confused now >_>
Click to expand...
Click to collapse
but if You:
- open flashtools on Your pc
- connect phone by cable - also powered-off, what did You read from flashtool?
Here You can find it...
http://forum.xda-developers.com/showthread.php?t=826455
Let me know...
Cheers,
M.
Phone isn't detected.
EDIT: It doesn't respond with or without flash mode. But when I disconnect it from the cable, he blinks a red light 3 times in sequence. Same with home+power.
Mazzocato said:
Phone isn't detected.
EDIT: It doesn't respond with or without flash mode. But when I disconnect it from the cable, he blinks a red light 3 times in sequence. Same with home+power.
Click to expand...
Click to collapse
You've also installed the Gordons Gate drivers before doing Your tests?
from the flashtool folder install <flashtool folder>\drivers\gg-????.exe
Then reboot pc and re-try...
Yep. GG-setup.exe installed. Restarted.
Phone looks "dead". But it blinks red lights without the charger / cable usb.
Odd.
EDIT: Left charging on the wall with red blinking light. Dead again. No sign of life whatsoever.
Update:
Noticed that it "ignores" my attempts on the screen buttons. Back and home = same reaction... as if I wasn't pressing them.
I'm thinking that I've got hardware problems... or some HARD software issues. =/
Help NO gsm!!!
Hi I tried to unlock bootloader but after going through the tests my gsm failed to start working phone just says please insert sim card but there is nothing wrong with the sim. Please need advice