my XDA O2 mini S (wiza200) upgrade ROM but 98% -> Eror
Then i turn on my phone ...see.......: tree color (Dos screen)
now i can't setup Cert_SPCS.cab and EnableRapi.cab to reupgrade ROM, plz help
Try to reflash your phone with the original shipped ROM - that should work even in BOOTLOADER mode.
Related
hi ,
i was updating my xda11 from the o2 web site to v172181.
i followed all the instructions fully and half way through it gave a fail message.it told me to remove xda and cradle from computer and retry after reseting xda.
the xda is stuck in limbo with no backlighting and serial on top of the screen and v1.06 at the bottom.
how do i get back to the start.
i am no programmer so try to make it as user friendly as possible please.
thanks for any help or advice
rob
hi guys/gals
what time of the day or nite do the experts come on , i know its an international board
rob
when the screen is no blacklight and display "Serial" on top and "v1.06" on the bottom , this is the bootloader mode ....
you can put your device in craddle and re-run an upgrade in bootloader mode ....
- download an available upgrade for your device
- put your device in bootloader mode if it isn't it ( press and hold power button and reset until screen display "serial" & "v1.06")
- put your device in craddle
- upgrade your device normally
it should works fine
tofclock
thks for the reply
i will try that now ,i tried already but it wouldnt connect to active sync.
ah well , here goes again
rob
no , still wont connect to active sync
No need to connect with active sync ...
just put in bootloader mode , put in the craddle , and run himaupgradeut.exe
serching for himaupgradeut.exe on this site.have you a download path for it or can you tell where it is
cheers
rob
Ooooh ...
your upgrade is a .exe file ...
ok
in this .exe fie , there is 6 files
HimaClearJumpCode.exe --> ??
GetDeviceDate.exe --> to get device info
HimaUpgradeUt.exe --> to upgrade device
nk.nbf --> Os rom
Radio_.nbf --> Radio rom
ms_.nbf --> Extended_rom
rom for himalaya are on 2 different package :
zip file contains the 6 files
or exe file
the procedure is simple :
put your himalaya in bootloader mode
put the device in craddle
and then , if you have a rom upgrade like an exe file , run it , and if you have a zip file , unzip it and run himaupgradeut.exe
you can find all files you need
HERE
or
HERE
tofclock ,
great advice so far , thanks
i tried the above links and i dont have permission to view/open site.
do i need a password or permission from a mod.
rob
oh sorry ......
Go to ftp://xda:[email protected] and then , navigate in folders Himalaya or HimalayaSeS
tofclock ,
I figured out what happened by trawling through old topics and the help i recieved from yourself.
i presumed the usb conection feed power to xda11 as i have the ac charger in my bedroom for topping up battery.
i connected ac charger to cradle and reran upgrade and bingo
thanks for all the help friend
friend want to install 5.0 to Qteq 8200 (i-mate sp4, spv c550 )
follow instructiom from this site
http://user.cityline.ru/~ronswens/Tutorials.htm
- make CID remove ( SPV-Service )
- download SPL 1.01.0109
- flash SPL 1.01.0109 to mobile til 100%, ask about reboot phone, rebooted ..
- start phone = white screen
Somthing wrong with bootloader ? reflash it ?
What we must do ? help please.
same problem here, very ennoying, any body any idea on how to restore?
Thnx
Djslash
its because the WM5 upgrade is for typhoons not hurricanes. youve just trashed your bootloader by installing a typhoon one. back to the manufactuer now.
I have killed a touch dual (bad uspl - unlocking) now I have a bricked device ( in tricolors) could someone help me with this rom? (france rom)
please
For all OEM Roms -> http://netrunnerat.4shared.com/
This is a France OEM Rom -> http://www.4shared.com/file/37899406/68f31967/RUU_Nike_HTC_FR_13140609_Signed.html
thank you, man!
but now a have an other problem...
early I`ve tried to restore a original rom thru mtty command - task 32 and other commands.
now when I try to flash a fully original rom, device stuck in 0% upgraiding (I mean a grey backgroung flashing mode stuck in 0%... ) I think I enter a bad command thru mtty - could someone help me to restore original parametrs?
please.
Hi
Have you tried the command "boot" in mtty?
If you had unbricked your phone and are trying to change the Rom, don't forget to use USPL. Tell us if it works (or not ^^')
it show that in device no OS...
but problem left
Uhm ... bad ... the problem is ... at the moment i havent a full FR rom with all parts. what have you try?
MTTY have reboot your device? then its crashs or go back to bootloader? what roms have you try? what SPL version you see in bootloader?
NIKI100
SPL 1.16.0000
CPLD-4
a have added you in ICQ - could you go there, I`ll be wait you there - it`s faster, please.
send me a message
it`s seem to me that we have a bad france rom - cus I choose an other rom - Rus rom - process stopping on 2% - with ID-problem ) (I`m not make an Hardspl..)
could you check it?
Can you send me the link of this rom! I need it for my OEM Rom collection!
Next ... if it stops via 2% with ID Problem -> your device isnt cid unlocked!! This is your main Problem!
Yeah, I know it, I wrote that in my first message.
so, I could solve this problem if I have a flashing original rom.
history:
thank you, man!
but now a have an other problem...
early I`ve tried to restore a original rom thru mtty command - task 32 and other commands.
now when I try to flash a fully original rom, device stuck in 0% upgraiding (I mean a grey backgroung flashing mode stuck in 0%... ) I think I enter a bad command thru mtty - could someone help me to restore original parametrs?
it`s seem to me that we have a bad france rom - cus I choose an other rom - Rus rom - process stopping on 2% - with ID-problem ) (I`m not make an Hardspl..)
could you check it?
so could you flash your working device with francerom -to check - rom are flashing?
http://rapidshare.com/files/8878378....411.09_Radio_Nike_1.58.16.27_signed_Ship.exe
One question ... what was your first Rom on your phone? I want know the shipped rom!
touch dual - orange, france.
i cant explane ... no rom in my OEM folder can flash your device without Hardspl or uspl is installed!!! you need MTTY and use command "boot" to start your os! then you flash again! if your OS partition is deleted with useing Task 32 ... you have a problem!!! your device has a FR CID ... only a original FR rom can flash your device and i havent see a original FR rom in the moment! this is why i collect them! this is in a lot errors the best way to fix!
ok, but finally thanks for help.
ok, finally thanks for help.
Hello did somebody know from where i can download original WM 6 or 6.1 ROM for HP IPAQrw6815-not modified?
thanks
Teodor
[email protected]
hp doesn't come out with WM6 or WM6.1 for ipaq 6815.... there's only custom roms which are modified to work with ipaq 6815... you can choose from a variety of them in here.... have fun!...
thaks for this
Help with My ipaq 6815
Nhocbanme hi,
i've read thru many of the replies in this forum. i'm a newbie and don't knw much abt roms. i tried upgrading or if u call it flashing my ipaq via PC and later SD. the PC flash did not work. i had to wait almost the whole day becos it said it was reading configuration from the phone. i later tried the flash via a transcend 1GB miniSD and till today the phone has gone off. i tried to power it on even with th e battery fully charged. my sis has the same phone i tried swapping batteries but it still didn't come on. i really need to upgrade to windows mobile 6.1 i formerly had WM 5.0, today itried again and it still stays on the boot screen.(white background with the HP logo and the Pbl 1.05 at the botton of the screen .
please i need help ASAP.
Downlgrade your bootloader to 1.01
Hi,
You have to downgrade your bootloader from 1.05 to 1.01. Find in the following the instructions how to do it. I did it and it's working.
Be careful when you do downgrade, because you can end up without phone
Quote:
How to flash from PC with Windows XP (It is ok to run it in vmware)
Thanks Knave and rcperez for posting their detailed experience so I can write this section. Also thanks jimmyspa for improving the addheader's performance greatly.
1. Check your Boat loader version
(do a soft reset, and check the value printed at the bottom during the HP logo screen)
2. If you noticed that the last line states BL 1.00.05, it means you have boat loader 1.05 installed. You will need to download and flash your phone back to 1.01 via ftp://ftp.hp.com/pub/softpaq/sp34001-34500/sp34053.exe (VERY DANGEROUS, FLASHING VIA SD IS MUCH SAFER!)
3. After successfully downgraded your phone's boatloader, or your version was already v1.01, you can proceed to flash your phone to the rom.
With the check done, proceed with the required files.
1. Go to download section to download the rom file. -- The rom that you downloaded, e.g (diskimg.nbo)
2. Download the file pcupdate.zip attached in this thread and unzip the contents to the same folder you used in step 1.
3. Download the latest Rom file and extract to the same folder
4. Run BuffereAddHeader.bat. It will take seconds to generate a diskimage_Ver.nb0. (You should have Java Runtime > 1.50 installed, http://www.java.com/en/download/manual.jsp)
5. Move your phone to boatloader mode ( press the two - keys, follow by a poke at the soft reset hole with your stylus )
6. Connect the phone to the PC
7. Execute the Device Utility Update program and wait till it verifies the state. Click on Update Item "All" use cursor keys to change it to "OS ONLY" then hit next **** SELECT "OS ONLY", if you cant change it to "OS ONLY" DONT PROCEED!!! It should detect your device as Model 0 etc.
8. Press Next to begin flashing.
9. Once completed, the phone will reset by itself. Wait for a while for it to startup.
REMEMBER SELECT OS ONLY BY PRESSING DOWN IN THE SELECTION BOX
Here are the notes & files provided by hochengsoon with README for flashing via Windows XP
PC flashing using BL1.0.1 must be done from C:\Windows\Temp, so why not start everthing from this folder ie PCUpdate + ROM + missing file(s).
PCUpdate1.rar - http://www.mediafire.com/file/k5jumzzg1mm/PCUpdate1.rar
How to downgrade to WM5 using PC
1. download wm5 rom from http://h20000.www2.hp.com/bizsupport...pappid=NextGen
2. run it and after entering the updating screen cancel it.
3. replace the hpRUU.exe in c:\IPAQ(default install) with the attached file hpRUU.exe in archive hpRUU.zip
4. Connect device to PC, then press and hold two "-" button and reset.
5. Run hpRUU.exe and do a normal update.
Note: you may delete eboot*.nbf to prevent bricking the device.
bootloader missing
well i m using HP rw 6815, n last night i had flashed a 6.5 rom , later i was unsatisfied with tat rom,
so i went 2 change it, n during tat process, my phone turned off, n now it doesnt switch on, 1ce i managed 2 go 2 boot screen thr i cud see hp logo n bl-0.0.0 can ne1 help me out with it, how do i put bootloader in phone.. neither my pc detects the phone... help appriciated
HI i had same problem on hp rw6815
No bootloade aparantly but bootloader hp logo loaded but insted o o.0.o i had a ff.ff.ff bootloader. i dunno what that meant. i inserted a eboot.nb0 on sd reseted in bl (v1.0.5 from this forum).... bootloader updated oki.. but my phone transformed in a hp rw6828, and i can install 6828 rom working and bootin fine in rw6815, the rw6815 rom install via sd but restarts on boot screenn .. this appeard when i tried a downgrade from wm6.5 to wm5 when i try to upgrade via hpruu it looks tat i have a no language hpipaq model.. My model info is "€ R 0 6 0 8 2 2 N _ M N 1 A R C _ R S 0 0 0 5 2" i dont know how to interpret this file sysyinfo.txt with that data. my question is how can i downgrade to wm5 and original bl of hp rw6815? i have all files in nbf form. The onli soluton to the problem if ur phone restarts after rom upgrade downgrade on witn wm 6.5 an 1.01 bl is the atrached rom.. workin 6815-camera-patched-R3.zip is the only rom... located here http://forum.xda-developers.com/showthread.php?t=360664 second post under orher roms
6815 camera patch may work version r2: http://www.mediafire.com/?lihy0vcvnxd
6815 camera patched version R3: http://www.mediafire.com/?2mjhtgjox0x
This roms get ur phone alive after this bug... or the restar bug... they work with both 1.0.1 bl and 1.0.5 bl more stable with 1.0.1... and i thing the developer of the rom did not change the indentifier of the rw6828 rof for 6815... i think it;s hybrid rom between... it works.
Plese help me to downgrade to original state... hp rw6815 bl 1.0.5 rom wm5. or help me solve the hpruu problem... not patched for model and lang beacouse it says the same incopatible thing.. the picture is the same result in patched and original ruu.. .
me too
i got that same problem i dont know wahta to do help guys
bootloader missing after Upgrading to wm 6.5
Hi Dear, i had the same problem but the solution is so funny.
1. Remove Battery from your mobile.
2. Remove SIM card too.
3. Wait around 5 min. & put them back again.
4. Everything should be OK
I hope Problem solve like me , But realy i don't know why ??? .
Best regards, Jalal
I tried to flash the 6815 is here and I have put my diskimg.nb0 on 2gb memory card. Press the 2 buttons with the "-" and give it to reset with a stick ... I get into the bootloader and returns to the screen while windows. It might be because the bootloader has the pda is 1.0.5??
The problem is that trying to change the bootloader 1.0.1 is here and not working because my pda is Spanish.
How can I reduce it?
Dear SHKUMBIN,
I am very grateful for the clear and beautiful explanation, which indicates that a great effort and considerable experience and also " NHOCBANME " and " ARIEY " for the great job they do to bring those custom rom's.
Accept my greetings.
karamzak
hi friends,
i have one swisscom xpa s200.
i bought this phone with this problem-when i power on,on the screen is only firs splash screen with ipl/spl=2.20.0001
i tried every WIKI method to recovery this device but no luck.
i dont have one official swisscom xpa s200 rom.
what is the problem,can you help me ?
thanks in advance.
greetings from serbia.
MS
Tell me if it works
Go and try get the original rom then enter bootloader mode to flash.Flashing may only be done on xp computers.Get the original rom from this xda site go 4shared.com or the original phone brand site
how to:
1. charge your device
2. make sure you have activesync installed.. if installed you will see an ActiveSync icon on the lower right part of your desktop right click it click connection settings and UNCHECK allow USB connections then press comm+cam +soft reset button to force your device on bootloader, you should see USB on the lower left screen of your device.
3. Download the NVID_RUU.zip extract it and RUN ( it has only one RUU, so it doesnt matter if your device is G3 or G4 )
4. after flashing the RUU and its succesfull try allowing USB connection again on Active Sync..
5. if its still not working.. try downloading the PV_Temp NVID RUU, i dont have a copy of this so try searching for this in the forums..
goodluck!!
PS: you can also read stiky threads over Prophet Mobile 6 Forum
NVID RUU : http://www.mediafire.com/?0wilzm3vzeo