hi friends,
i have one swisscom xpa s200.
i bought this phone with this problem-when i power on,on the screen is only firs splash screen with ipl/spl=2.20.0001
i tried every WIKI method to recovery this device but no luck.
i dont have one official swisscom xpa s200 rom.
what is the problem,can you help me ?
thanks in advance.
greetings from serbia.
MS
Tell me if it works
Go and try get the original rom then enter bootloader mode to flash.Flashing may only be done on xp computers.Get the original rom from this xda site go 4shared.com or the original phone brand site
how to:
1. charge your device
2. make sure you have activesync installed.. if installed you will see an ActiveSync icon on the lower right part of your desktop right click it click connection settings and UNCHECK allow USB connections then press comm+cam +soft reset button to force your device on bootloader, you should see USB on the lower left screen of your device.
3. Download the NVID_RUU.zip extract it and RUN ( it has only one RUU, so it doesnt matter if your device is G3 or G4 )
4. after flashing the RUU and its succesfull try allowing USB connection again on Active Sync..
5. if its still not working.. try downloading the PV_Temp NVID RUU, i dont have a copy of this so try searching for this in the forums..
goodluck!!
PS: you can also read stiky threads over Prophet Mobile 6 Forum
NVID RUU : http://www.mediafire.com/?0wilzm3vzeo
Related
hi ,
i was updating my xda11 from the o2 web site to v172181.
i followed all the instructions fully and half way through it gave a fail message.it told me to remove xda and cradle from computer and retry after reseting xda.
the xda is stuck in limbo with no backlighting and serial on top of the screen and v1.06 at the bottom.
how do i get back to the start.
i am no programmer so try to make it as user friendly as possible please.
thanks for any help or advice
rob
hi guys/gals
what time of the day or nite do the experts come on , i know its an international board
rob
when the screen is no blacklight and display "Serial" on top and "v1.06" on the bottom , this is the bootloader mode ....
you can put your device in craddle and re-run an upgrade in bootloader mode ....
- download an available upgrade for your device
- put your device in bootloader mode if it isn't it ( press and hold power button and reset until screen display "serial" & "v1.06")
- put your device in craddle
- upgrade your device normally
it should works fine
tofclock
thks for the reply
i will try that now ,i tried already but it wouldnt connect to active sync.
ah well , here goes again
rob
no , still wont connect to active sync
No need to connect with active sync ...
just put in bootloader mode , put in the craddle , and run himaupgradeut.exe
serching for himaupgradeut.exe on this site.have you a download path for it or can you tell where it is
cheers
rob
Ooooh ...
your upgrade is a .exe file ...
ok
in this .exe fie , there is 6 files
HimaClearJumpCode.exe --> ??
GetDeviceDate.exe --> to get device info
HimaUpgradeUt.exe --> to upgrade device
nk.nbf --> Os rom
Radio_.nbf --> Radio rom
ms_.nbf --> Extended_rom
rom for himalaya are on 2 different package :
zip file contains the 6 files
or exe file
the procedure is simple :
put your himalaya in bootloader mode
put the device in craddle
and then , if you have a rom upgrade like an exe file , run it , and if you have a zip file , unzip it and run himaupgradeut.exe
you can find all files you need
HERE
or
HERE
tofclock ,
great advice so far , thanks
i tried the above links and i dont have permission to view/open site.
do i need a password or permission from a mod.
rob
oh sorry ......
Go to ftp://xda:[email protected] and then , navigate in folders Himalaya or HimalayaSeS
tofclock ,
I figured out what happened by trawling through old topics and the help i recieved from yourself.
i presumed the usb conection feed power to xda11 as i have the ac charger in my bedroom for topping up battery.
i connected ac charger to cradle and reran upgrade and bingo
thanks for all the help friend
Hi does anyone know if there are WM6 ROMs for the SPV C550 if not are there any good WM5 ones?
look topic about wm5 for hurricane, there are also links to wm6 for hurricane device
hello again
here is latest, almost perfect rom for hurricane:
http://rapidshare.com/files/56833250/566.zip.html
and new SPL for this device:
http://rapidshare.com/files/56616745/spl566wm6_spfans2006.rar
lazaj007 said:
hello again
here is latest, almost perfect rom for hurricane:
http://rapidshare.com/files/56833250/566.zip.html
and new SPL for this device:
http://rapidshare.com/files/56616745/spl566wm6_spfans2006.rar
Click to expand...
Click to collapse
Has anybody tried this ROM?
lazaj007 said:
hello again
here is latest, almost perfect rom for hurricane:
http://rapidshare.com/files/56833250/566.zip.html
and new SPL for this device:
http://rapidshare.com/files/56616745/spl566wm6_spfans2006.rar
Click to expand...
Click to collapse
Ideal thanks
So is the 566.zip the WM5 or WM6 rom and has it been tested?
Whats the new SPL?
hI ALL, can u tell me the mini guide how to install this rom? I did it once to my sda but I dont remember now, where is the nbfupdatetool and RUU and patched RUU..???
when I type l c:\wm6.bin it give me this:
clean up the image temp buffer at 0x8C080000 Length 0x01B00000 MTTYDownloadImageNot allow operation!
Error : DownloadImage return error (code = 0xFFFFFFFF)
cmd>
maybe damaged rom, or any idea?
Gang: Make sure you're CID unlocked. (Eg, when you issue "info 2", it says HTCSuperCID).
How can do that cid unlock? give me some working link to download that tool or something. thx
here you go
http//www.spv-developers.com/content/SPV-Services.zip
you must check "CID Tool (Alpha)" and click set CID=11111111
after this restart your phone
and short solutions about wm6 installing:
* installation is the same like typhoon
-unlock Super CID
-upgrade new SPL (Patched ruu)
-disable USB connection in ActiveSync
-switch off your phone
-press and hold camera button, and put USB cable to your phone
-next check "Y"
-when your phone will be in bootloader mode (tri color screen) run mtty
- check USB connection in this program
and write: - info 2
- format BINFS
- l c:\566.bin (localization of your rom)
after succeful installising reboot your phone and it will be end
rom is very good, baterry work better
hmm, thx for guide, I believe it will work, but I have little problem : now I cant even connect to activesync so I cant do cid unlock, any idea how to fix that
lazaj007 said:
here you go
http//www.spv-developers.com/content/SPV-Services.zip
you must check "CID Tool (Alpha)" and click set CID=11111111
after this restart your phone
and short solutions about wm6 installing:
* installation is the same like typhoon
-unlock Super CID
-upgrade new SPL (Patched ruu)
-disable USB connection in ActiveSync
-switch off your phone
-press and hold camera button, and put USB cable to your phone
-next check "Y"
-when your phone will be in bootloader mode (tri color screen) run mtty
- check USB connection in this program
and write: - info 2
- format BINFS
- l c:\566.bin (localization of your rom)
after succeful installising reboot your phone and it will be end
rom is very good, baterry work better
Click to expand...
Click to collapse
Thanks for helping out!
A few questions?
1. This link "http//www.spv-developers.com/content/SPV-Services.zip" takes me to Wikipedia.
2. Where can I find the patched ruu to update the spl. It wasn't in the zip file?
Thanks in advance!
to Mr MIAGY :
1. just write that link starting with www. (without http//, or type http://)
2. in ''wm6 for c550'' topic u will find patched RUU and all needed files, they are ziped together
gangstaunitg said:
to Mr MIAGY :
1. just write that link starting with www. (without http//, or type http://)
2. in ''wm6 for c550'' topic u will find patched RUU and all needed files, they are ziped together
Click to expand...
Click to collapse
DoH! I didn't notice the missing ":"
Cheers!
Anybody have idea why I cant connect to activesync after spl upgrade ? Before spl upgrade it all goes well. Can I do something with it?
if upgrade was complited succes then you must turn off USB connection in Active sync, then run bootloder mode and do everything with instructions.
I did it !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
THank u all, thankS
This rom is amazing, everything work perfect, and it looks beautiful,
one more time thank you. jUUHHHUUUUUUUUU
lazaj007 said:
if upgrade was complited succes then you must turn off USB connection in Active sync, then run bootloder mode and do everything with instructions.
Click to expand...
Click to collapse
Upgrade reported as success
However after reboot I see the WM6 boot screen - loverly ...
Then the Mobile Operator Splash screen ... THEN
After too long ... the phone switches itself off and I have to take the battery out to get reponse again.
Any ideas?
It's a C550 ....
MrMiyagi said:
Upgrade reported as success
However after reboot I see the WM6 boot screen - loverly ...
Then the Mobile Operator Splash screen ... THEN
After too long ... the phone switches itself off and I have to take the battery out to get reponse again.
Any ideas?
It's a C550 ....
Click to expand...
Click to collapse
Ok, so a report. The phone boots, goes through WM6 splash screen, then operator screen, then APPARENTLY dead black screen.
BUT I plugged in the USB cable and the screen came on! WM6 Setup screen! All good go through setup eveything looks GREAT!
Only problem is, if I leave the phone alone for a bout a minute, the screen goes black AGAIN. Then no amount of key pressing on the device will bring it back to life.
Plugging the USB cable in brings it instantly back to life! But This means I can't wander too far from my PC ;-)
ANY Ideas
BTW IT LOOKS FANTASTIC! If I can just get around this issue ;-)
MrMiyagi said:
Ok, so a report. The phone boots, goes through WM6 splash screen, then operator screen, then APPARENTLY dead black screen.
BUT I plugged in the USB cable and the screen came on! WM6 Setup screen! All good go through setup eveything looks GREAT!
Only problem is, if I leave the phone alone for a bout a minute, the screen goes black AGAIN. Then no amount of key pressing on the device will bring it back to life.
Plugging the USB cable in brings it instantly back to life! But This means I can't wander too far from my PC ;-)
ANY Ideas
BTW IT LOOKS FANTASTIC! If I can just get around this issue ;-)
Click to expand...
Click to collapse
Heh heh ... seems I'm posting to myself ... that's cool I like my own company ... So I reflashed the SPL and some of the problems have gone away.
Phone will boot OK now ... but it will still "go to blank screen" and require plugging into the USB cable to "wake it up"
I'm out of ideas now ...
i had a t mobile g4 device which was simunlocked but not cid unlocked.
i upgrade only the radio version without cidunlocking it..
not i cant get gsm line in boot menu
the device cannot charge niether cannot be seen by my computer.
when i put in boot loader menu an coonect it to usb in boot loader menu
there is usb written in down left cornor but i cant load any room to even the original t mobile room
did i breach my phone..i think yes..
i can manage to replace my usb (phone usb not cable) does this will fix it or not
halder said:
i had a t mobile g4 device which was simunlocked but not cid unlocked.
i upgrade only the radio version without cidunlocking it..
not i cant get gsm line in boot menu
the device cannot charge niether cannot be seen by my computer.
when i put in boot loader menu an coonect it to usb in boot loader menu
there is usb written in down left cornor but i cant load any room to even the original t mobile room
did i breach my phone..i think yes..
i can manage to replace my usb (phone usb not cable) does this will fix it or not
Click to expand...
Click to collapse
read the post
How to flash a new ROM to your Wizard... a little tutorial!
http://forum.xda-developers.com/showthread.php?t=310831
G4.1 Does you're device start normally (yes) or is it stuck on the three-colored bootloader screen (no)? YES... go to step G4.4, NO go to step G4.2
G4.2 Turn off you're device totaly. Remove the SD card and disconnect the USB cable from you're device. Turn on the device while holding the camera button. You will get into bootloader mode (3 colored screen). Connect the USB cable to the computer and you will see USB at the bottom of your screen above the left softkey (Activesync will not connect in bootloader mode, but you can flash from this screen!). go to G4.3
G4.3 Download wizard_love rom and flash it to your device. Your device should startup again after doing this. Go to G4.4.
G4.4 Is your device CID-unlocked (note: it's not the same as SIM-unlocked!)? YES... go to step G4.7, NO OR DON'T KNOW go to step G4.5. (note: CID-unlocking a G4 is only possible by paying for it at imei-check!)
G4.5 Download enable-rapi.zip. Transfer Cert_SPCS.cab and EnableRapi.cab to your phone. Run Cert_SPCS.cab FIRST and EnableRapi.cab SECOND. Turn your device off and on or wait 5 minutes before soft resetting. Done? Go to G4.6.
G4.6 Follow this great thread by the-equinoxe: [solution] G4 SoftSPL Flash any ROM to CID locked G4 [UPDATED] and load the softSPL on your device using his method. Make sure you take a G4 safe rom (see the thread for details). After the steps you'll have the rom of your choise on your device!
G4.7 You're reade to flash the AKU2, AKU3, WM6 rom of you're choise IF the rom DOESN'T contain IPL/SPL. AKU3 and WM6 roms normally don't contain IPL/SPL. If you want to flash an AKU2 rom, make sure you take the G4 version. If you get an error 300 (invalid update tool) while trying to flash your device look at this thread!
NOTE: If you tried to flash a G3 rom with IPL/SPL in the rom on a G4 you probably will have a bricked device! DON'T flash the new 3.08 and 3.09 IPL/SPL to your G4!
NOTE2: If you got problems flashing with softSPL: Follow this great thread by mun_rus: Solutuion found: how to flash any rom to CIDLOCKED DEVICE. If your device won't start after flashing you can use step G4.2 and G4.3 and try again. Also look at this thread by eddieitman: Faria G4 Step by step installer with instructions to make sure you did all the necessary steps!
thank you thank you very much
if say thank from now till the end of this years its not enough for u
i did that and folow this tremendus amount of instruction.it work again ican not believe my eye.....
now can i upgrade it wm6
do u have a link for wm6 for g4
thank again
As soon as you load SoftSPL or HardSPL into your G4 Wizard, you should be able to use any new WM6 ROM released in the "Wizard WM6" subforum.
Just double check the ROM does not have IPL and SPL in it, then you can go flashing with equipped RUU directly.
And...make sure you have your T-Mobile original ROM or Wizard ROM ready in case of any accident during flashing so you can always return to original WM5.
I Have had this new pda one day yes today and ive managed to f**k it up already
it had windows mobile 5 on it and i wanted to upgrade it to wm6 so i could use flo touch and get the better graphics well i tried at updating and reflashing but all i got was errors and now when i turn it on i get the orange bootloader screen with the text:-
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 10.2.0.8
but nothing else it is now not recognise by the pc and will not boot up even after a hard reset!
please someone help me get through this problem quick!?!
Cheers a bunch Daniel.
Download activesync 4.5 (search for it)
Download this: http://cid-cddbf77985693632.skydrive.live.com/self.aspx/XDA%20files/ROMs/RUU_Prophet_220734_2207114_024721_NVID.exe
In activesync, disable connect through USB.
Run the RUU you downloaded above.
i have downloaded and installed active sync 4.5 as directed on a pc running windows xp and disabled connect through usb by right clicking it on the desktop in the taskbar and clicking connection settings then un-checking the usb connect box. then i connected my prophet and it installed it as a PocketPC USB Sync of something like that and it appears in my computer as a mobile device but when i click it it has nothing in it so i ran the RUU and it asked to update the ROM so i followed the steps but it asked me to make an active sync connection which i cant because the prophet wont turn on after the bootloader the pc recognised it when it was switched off. PLEASE SOMEONE HELP!?!
Unplug the prophet.
Manually enter bootloader and reconnect the device.
then try reflashing the ROM.
Just continue with the RUU unless it gives an error.
i have just right clicked it under device manager and it is recognised as "Windows CE USB Devices" then expands to "PocketPC USB Sync" but how do i manually edit the bootloader if that it was i still have to do sorry im a newbie to this stuff as i said ive only had it one day
it is recognized in the device hardware section but it says there is a fault or something i dont know. there is nothing wrong with the prophet i am 100% sure its just recognised as that because its not turning on properly i think. how do i manually edit the bootloader and what would i need to edit sorry im a newbie at this stuff as you know ive only had it one day and all this because i wanted flo touch
Start up the device normally. Then, press and hold the Comm manager button whilst reseting (stylus into the hole to the left of the power socket). Now, plug the device into the computer and run the RUU.
Thank you so much!!! LIFE SAVER!! its updating now thank you so much il tell you how it goes when its complete TOP HELP!
Thank You Success My Friend!! Woooooooo!! Im A Happy 16 Yr Old :d
Done your GCSEs yet? I'm an unhappy 16 yr old... My Prophet rocks, but my coursework fails...
Do you know how i can put on the flo touch ? when i send across the cab file it installs but doesnt show anything i just clicked on about aswell on the device and it says its still windows mobile 5 ? is it really windows mobile 6 ? i just really want flo touch ?
and nope not yet my GCSE's are in 2 months.
That ROM is WM5. I would suggest updating to a WM6 ROM such as one of Cloudyfas ROMs. Search for it and read all the relavent threads.
To launch the cube, swipe your finger from the top of the screen to the bottom of the screen.
the touch edition or clean edition mate ?
Touch edition will have Touch Flo.
use Prophet Tools to make it faster...
where can i get this prophet tools you speak of ? and what will i have to do i have successfully installed wm6 touch edition now the one you recommended but what about the prophet tools ?
there is a link in my signature to prophet Tools it should all be explained there. also read the new upgrade guide sticky in the WM6 forum. Prophet tools is to help upgrade, so no need for that now...
The touch flo cube should activate in the way i said above.
ok so i have downloaded the little extra on the page of the ShadoW Touch ROM and its called ShadoW Cube and i have installed it yet nothing happens its not even in the device menus. do i need to upgrade it like you said with this tool and how ?
The cube only starts when you slide your finger fRom the bottom of the screen to the top...
hi guys
I have a bricked hermes
DOPOD 8525 -> WM 6.1 Professional
From bootloader screen
HERM100 IPL-1.01
bootloader SPL-1,40.01ipro
Tried to flash ROM using safe SSPL with RUUwrapper.
At completion of flash both my mobiler & win mobile device centre disconected or lost connection with device, after soft reset will only load up to second HTC screen. How can I recover from this brick? device manager recognises HTC usb sync when plugged in but I can't connect to re flash rom.
Reading helps my friend
Get to bootloader, press ok and power on left and right respectively and stick stylus in all at same time.
that should bring up tricolour screen.
Download your imate jasjam official ROM
EDIT i think you got a dopod so the dopod ROM is what you want from my 4shared or wiki!!
from the wiki or from my 4shared, and flash it while it is in boot loader mode.
then you need to flash hard spl one of the first stickys on this thread that you have just posted to.
Then flash your desired rom.
Thank you Zocster
Got it unbricked & working, thanks to you I have a lot of trouble reading as I am leagally blind but get by with T2V & magnifiers most times. however searching threads is a lot harder than for most.
thanks
Lou
PS if you ever cross the tasman drop me a line
loulian, to make it easier to recover from bricks, It would be best if you flashed Hard SPL V7 from here - http://forum.xda-developers.com/showthread.php?t=296722
It won't guarantee a flawless flash but will help if something goes wrong by giving you a GOOD chance of recovery.
You can then use the sd card method and make life easier by not having to worry about pc crashes, cables being pulled, blackouts or those annoying "sync" errros.
Cheers...
Also if you have trouble setting up your Hermes after a flash/hard reset because of the alignment points being hard to see, It would be a good idea to download this -
http://www.codefactory.es/en/downloads.asp?id=44
It will, after you save the settings, allow you to use your PC to set up the Alignment point if you need to Hard Reset or flash your phone making it load the os to the today screen.
zocster said:
Reading helps my friend
Get to bootloader, press ok and power on left and right respectively and stick stylus in all at same time.
that should bring up tricolour screen.
Download your imate jasjam official ROM
EDIT i think you got a dopod so the dopod ROM is what you want from my 4shared or wiki!!
from the wiki or from my 4shared, and flash it while it is in boot loader mode.
then you need to flash hard spl one of the first stickys on this thread that you have just posted to.
Then flash your desired rom.
Click to expand...
Click to collapse
Sorry to ask a stupid question. I have the same problem, but when i try to flush it from a TriColor mode i get a communication error, it complains about activesynch not connected. BTY mine is cingular 8525 so i am trying to use one of the cingular roms.