i had a t mobile g4 device which was simunlocked but not cid unlocked.
i upgrade only the radio version without cidunlocking it..
not i cant get gsm line in boot menu
the device cannot charge niether cannot be seen by my computer.
when i put in boot loader menu an coonect it to usb in boot loader menu
there is usb written in down left cornor but i cant load any room to even the original t mobile room
did i breach my phone..i think yes..
i can manage to replace my usb (phone usb not cable) does this will fix it or not
halder said:
i had a t mobile g4 device which was simunlocked but not cid unlocked.
i upgrade only the radio version without cidunlocking it..
not i cant get gsm line in boot menu
the device cannot charge niether cannot be seen by my computer.
when i put in boot loader menu an coonect it to usb in boot loader menu
there is usb written in down left cornor but i cant load any room to even the original t mobile room
did i breach my phone..i think yes..
i can manage to replace my usb (phone usb not cable) does this will fix it or not
Click to expand...
Click to collapse
read the post
How to flash a new ROM to your Wizard... a little tutorial!
http://forum.xda-developers.com/showthread.php?t=310831
G4.1 Does you're device start normally (yes) or is it stuck on the three-colored bootloader screen (no)? YES... go to step G4.4, NO go to step G4.2
G4.2 Turn off you're device totaly. Remove the SD card and disconnect the USB cable from you're device. Turn on the device while holding the camera button. You will get into bootloader mode (3 colored screen). Connect the USB cable to the computer and you will see USB at the bottom of your screen above the left softkey (Activesync will not connect in bootloader mode, but you can flash from this screen!). go to G4.3
G4.3 Download wizard_love rom and flash it to your device. Your device should startup again after doing this. Go to G4.4.
G4.4 Is your device CID-unlocked (note: it's not the same as SIM-unlocked!)? YES... go to step G4.7, NO OR DON'T KNOW go to step G4.5. (note: CID-unlocking a G4 is only possible by paying for it at imei-check!)
G4.5 Download enable-rapi.zip. Transfer Cert_SPCS.cab and EnableRapi.cab to your phone. Run Cert_SPCS.cab FIRST and EnableRapi.cab SECOND. Turn your device off and on or wait 5 minutes before soft resetting. Done? Go to G4.6.
G4.6 Follow this great thread by the-equinoxe: [solution] G4 SoftSPL Flash any ROM to CID locked G4 [UPDATED] and load the softSPL on your device using his method. Make sure you take a G4 safe rom (see the thread for details). After the steps you'll have the rom of your choise on your device!
G4.7 You're reade to flash the AKU2, AKU3, WM6 rom of you're choise IF the rom DOESN'T contain IPL/SPL. AKU3 and WM6 roms normally don't contain IPL/SPL. If you want to flash an AKU2 rom, make sure you take the G4 version. If you get an error 300 (invalid update tool) while trying to flash your device look at this thread!
NOTE: If you tried to flash a G3 rom with IPL/SPL in the rom on a G4 you probably will have a bricked device! DON'T flash the new 3.08 and 3.09 IPL/SPL to your G4!
NOTE2: If you got problems flashing with softSPL: Follow this great thread by mun_rus: Solutuion found: how to flash any rom to CIDLOCKED DEVICE. If your device won't start after flashing you can use step G4.2 and G4.3 and try again. Also look at this thread by eddieitman: Faria G4 Step by step installer with instructions to make sure you did all the necessary steps!
thank you thank you very much
if say thank from now till the end of this years its not enough for u
i did that and folow this tremendus amount of instruction.it work again ican not believe my eye.....
now can i upgrade it wm6
do u have a link for wm6 for g4
thank again
As soon as you load SoftSPL or HardSPL into your G4 Wizard, you should be able to use any new WM6 ROM released in the "Wizard WM6" subforum.
Just double check the ROM does not have IPL and SPL in it, then you can go flashing with equipped RUU directly.
And...make sure you have your T-Mobile original ROM or Wizard ROM ready in case of any accident during flashing so you can always return to original WM5.
Related
Apparently, I'm pretty stupid.
I just got the Cingular 8525; I have spent two hours on this site.
Things I've noticed:
One page says go into bootloader; one page says not to allow usb connections.
I do not know if I am supposed to have my non-Cingular SIM card already in the phone when attempting to do anything.
I have seen connect via USB and use mtty (with what settings do I use when I click on USB from the dropdown menu (if any) and do I connect with mtty via USB in bootloader or when the phone has booted into Windows 5.0 and again what about the non-Cingular SIM card?).
I have flashed my computers BIOS several times but I do not understand how to flash this phone based on the myriad of instructions all over this site (and RFTW did not help which is why I am here with 40000000 questions).
The steps to go from SPL 1.06 to an unlocked SIM/CID phone are?
Things I do understand:
I have SPL 1.06 (I know this from bootloader).
I must downgrade to 1.04 from 1.06 then run the upgrade to 1.06 from the Hermes Upgrade wiki page (I already downloaded all of the Cingular files).
Thanks in advance for any clarification.
I unlocked my 8525 last week, I had bootloader 1.06 so I downgraded to a ROM with boetloader 1.04(you can find it here http://wiki.xda-developers.com/index.php?pagename=Hermes_Upgrades ).. then just follow the instructions in the zip file you downloaded(i used HERM_Unlock_v2a), which are:
1. Enter bootloader mode on your Phone. To do this, simultaneously hold side OK and POWER buttons together and reset with stylus.
[You should see SPL-1.04 on the top of the tri-color screen, if you see SPL-1.06 this unlocker will not work, please wait for the next version]
2. Connect your phone to your computer using the USB lead.
3. Run the MaUpgradeUt_noID.exe program – this will reflash your phone with a patched radio ROM required to unlock.
4. Wait patiently.
5. Once the MaUpgradeUt_noID.exe upgrade completes, it will end up saying "Upgrade Error 114", but the patched radio ROM will be flashed anyway, dont worry about that error!
6. Soft reset with stylus (Device will not be hard reset and no data will be lost)
7. Allow your phone to reboot. Once it has, connect to your PC using Activesync, and copy the HERM_Unlock_v2a.exe program onto your phone. Alternatively, copy it to an SD card and insert into your phone.
8. Run HERM_Unlock_v2a.exe on your phone. Wait about 1 minute.
9. You should see a "SUCCESS!" message from HERM_Unlock_v2a.exe, after that soft reset your phone.
10. Process is (hopefully) complete!
11. If the phone requests unlock code when you put a locked SIM, the code is: 22051978
I assume I want go to 1.04 for Cingular which is 1.30.502.1.
What about my SIM card? Is it supposed to be in phone when I run this file? (it's a t-mobile sim).
I assume the activesync connection via usb is okay? I cannot get it to connect (even though the phone is on and booted into Windows 5.0); is this because I have not inserted the SIM card into the phone? Note: after I unplugged the device, setting allow USB connections on the device in the ActiveSync settings, then plugging it back in, it connected via USB in ActiveSync (4.2). However, I just got a box saying the version of ActiveSync is not compatible with this mobile device. This occured after I started the installer and it showing Verifying the information on your PDA phone.
I received an update error 260 since it thinks the phone is not connected via USB (and I noticed the ActiveSync icon in the system tray is gone).
I went to check the M$ page to see if there is a later download; there is not. Then, the AS icon return (trying to update outlook, install nero mobile) so I decided to run the installer again and now sees my current version 1.34.502.1 and I have the option to upgrade ROM
MilanoRex said:
I unlocked my 8525 last week, I had bootloader 1.06 so I downgraded to a ROM with boetloader 1.04(you can find it here http://wiki.xda-developers.com/index.php?pagename=Hermes_Upgrades ).. then just follow the instructions in the zip file you downloaded(i used HERM_Unlock_v2a), which are:
1. Enter bootloader mode on your Phone. To do this, simultaneously hold side OK and POWER buttons together and reset with stylus.
[You should see SPL-1.04 on the top of the tri-color screen, if you see SPL-1.06 this unlocker will not work, please wait for the next version]
2. Connect your phone to your computer using the USB lead.
3. Run the MaUpgradeUt_noID.exe program – this will reflash your phone with a patched radio ROM required to unlock.
4. Wait patiently.
5. Once the MaUpgradeUt_noID.exe upgrade completes, it will end up saying "Upgrade Error 114", but the patched radio ROM will be flashed anyway, dont worry about that error!
6. Soft reset with stylus (Device will not be hard reset and no data will be lost)
7. Allow your phone to reboot. Once it has, connect to your PC using Activesync, and copy the HERM_Unlock_v2a.exe program onto your phone. Alternatively, copy it to an SD card and insert into your phone.
8. Run HERM_Unlock_v2a.exe on your phone. Wait about 1 minute.
9. You should see a "SUCCESS!" message from HERM_Unlock_v2a.exe, after that soft reset your phone.
10. Process is (hopefully) complete!
11. If the phone requests unlock code when you put a locked SIM, the code is: 22051978
Click to expand...
Click to collapse
crazyut said:
I assume I want go to 1.04 for Cingular which is 1.30.502.1.
Click to expand...
Click to collapse
right
crazyut said:
What about my SIM card? Is it supposed to be in phone when I run this file? (it's a t-mobile sim).
Click to expand...
Click to collapse
doesn't matter
crazyut said:
I assume the activesync connection via usb is okay?
Click to expand...
Click to collapse
It is ok, but generally it causes more problems than it helps. Best is to disable the checkbox that says "enable usb connections" on activesync settings and you'll see the icon on the system tray turn gray with a red "X". Then you need to start the RUU when the device is in bootloader mode (tri-color screen). After you have upgrded the rom (or radio rom) you can reenable activesync again if you want.
crazyut said:
I cannot get it to connect (even though the phone is on and booted into Windows 5.0); is this because I have not inserted the SIM card into the phone?
Click to expand...
Click to collapse
SIM card and activesync have nothing to do.
crazyut said:
I received an update error 260 since it thinks the phone is not connected via USB (and I noticed the ActiveSync icon in the system tray is gone).
Click to expand...
Click to collapse
Icon was gone because RUU checks your current rom version using activesync and then kills it an put device in bootloaer mode. If RUU cannot kill activesync correctly errors happen:
You will avoid the 260 error if you disable usb connections on desktop activesync as I told you, and start the upgrade in bootloader mode... only difference you'll notice is that RUU will not report your current rom version.
Hey. I left the RUU software running (the 25+ minute variety) while I went to buy a case and care charger. I came back and evidently, the phone had rebooted because, it is at the Windows Mobile screen to setup the Windows Mobile device. I assume it is safe to do the 2a software. After that, am I able to update the RUU back to 1.06?
Thanks for your help, Milan and pof!
I rebooted into bootloader to confirm successful downgrade to 1.04 from 1.06 and it was. The RUU software from the upgrade page for Cingular appears to have been successful.
I am now going to attempt the 2a software.
Yes, now follow all the instructions on sim&cid unlocker v2a, and when finished, flash the cingular 1.34 rom again.
pof said:
Yes, now follow all the instructions on sim&cid unlocker v2a, and when finished, flash the cingular 1.34 rom again.
Click to expand...
Click to collapse
It's now on the upgrade screen to Radio 1.16.00.69 but it does not show the previous version. Is this normal? I have not pressed upgrade yet. I have the splitter with the AC and USB cables into the phone (currently in bootloader mode at SPL-1.04).
yes, it is normal... i told you before:
pof said:
RUU checks your current rom version using activesync
[...]
start the upgrade in bootloader mode... only difference you'll notice is that RUU will not report your current rom version.
Click to expand...
Click to collapse
pof said:
yes, it is normal... i told you before:
Click to expand...
Click to collapse
I got the 114 error as promised in the readme. I exited the program using the EXIT button.
The next step:
6. Soft reset with stylus (Device will not be hard reset and no data will be lost)
On the phone display, it still shows Upgrade Radio Stack Please Wait..
The soft reset is the simultaneous OK and Power?
I just took the battery out and reset; it appeared to go okay. I copied the exe file to the phone and was able to run the file as in the readme. I then reset the phone, put in the t-mobile sim and it works.
Thanks much to POF and Milan for their straightforward approach. You can use this thread as a tutorial!
Is there any reason I should add the 1.06 file back to the unlocked 8525?
SPL 1.06 to SPL 1.04 back to SPL 1.06?
Hi:
I followed pof's (with pof's help) tutorial on how to unlock the Cingular 8525. I am currently at SPL 1.04 (downgraded form SPL 1.06) and had run the v2a software to unlock. It works great with T-mobile (I was a Cingular customer but made the switch).
My questions are:
Is there any reason to go back SPL 1.06?
If I do go back to SPL 1.06, it does not affect the unlock status of the SIM or CID?
I still am confused about the Radio and what that does in relation to the CID, SIM, or phone. I assume the Radio is affected the SPL version that you have?
I have tried to peruse through various pages regarding downgrading (the 13 page thread for example) to see if that question is answered.
The radio ROM controls the GSM/GPRS/UMTS hardware in your hermes. You cannot independently upgrade it unless you are running SPL 1.04. There is no reason IMO to go to any other bootloader version.
Sleuth255 said:
The radio ROM controls the GSM/GPRS/UMTS hardware in your hermes. You cannot independently upgrade it unless you are running SPL 1.04. There is no reason IMO to go to any other bootloader version.
Click to expand...
Click to collapse
Oh okay, that clears up yet something else I did not understand
Thanks for the tip on the bootloader version; I will leave it at SPL 1.04.
That being said, I am currently in the middle of the Radio 1.20 thread; I have not finished reading it yet (I can only do so much at work before people wonder what I am doing). Have you upgraded to Radio 1.20? If not, what radio are you running and what do you think of its stability and/or functionality?
Thanks!
I'm running the 1.20 radio. It and the 1.35 TyTN ROM are the best combination I've used so far.
Hi All,
I tried flash by wizard following http://forum.xda-developers.com/showthread.php?t=298967
Every thing went well but I was not able to HARD RESET. So instead I removed the battery and started it again. It starts up but got struck at screen which says
IPL 2.21.0001
SPL 2.21.0001
GSM 02.19.11
OS 2.18.00
Could some help me what to do now. I read some threads to go to Boot loader screen by pressing "Camera" + "Reset" button and got USB at bottom left and tried RUU with some thing available on forum but every thing failed saying "connection not established"
Please guide me to solve this problem.
if ur device is CID LOCKED "G4" u need to flash the official rom 1st then flash with any G4 safe rom available >>
USING :
ShellTool
http://forum.xda-developers.com/showthread.php?t=293480
or
SoftSPL
http://forum.xda-developers.com/showthread.php?t=329147
Thats the only way for G4 "CID LOCKED"
No...
If OS is not boot up correctly, both ways doesn't work because all of them requires to do in a working OS.
You should find your stock ROM or Wizard Love ROM, use the bundled RUU to flash it so you get the device working again, then use SoftSPL/flash HardSPL and use RUU to flash OS-only WM6 ROMs.
Yes starkwong you are right. I bought my device back working by flashing it with "wizard love" now its up and running. I would proceed with Soft SPL/Hard SPL and then try to flash it with WM6.
hi guys
I have a bricked hermes
DOPOD 8525 -> WM 6.1 Professional
From bootloader screen
HERM100 IPL-1.01
bootloader SPL-1,40.01ipro
Tried to flash ROM using safe SSPL with RUUwrapper.
At completion of flash both my mobiler & win mobile device centre disconected or lost connection with device, after soft reset will only load up to second HTC screen. How can I recover from this brick? device manager recognises HTC usb sync when plugged in but I can't connect to re flash rom.
Reading helps my friend
Get to bootloader, press ok and power on left and right respectively and stick stylus in all at same time.
that should bring up tricolour screen.
Download your imate jasjam official ROM
EDIT i think you got a dopod so the dopod ROM is what you want from my 4shared or wiki!!
from the wiki or from my 4shared, and flash it while it is in boot loader mode.
then you need to flash hard spl one of the first stickys on this thread that you have just posted to.
Then flash your desired rom.
Thank you Zocster
Got it unbricked & working, thanks to you I have a lot of trouble reading as I am leagally blind but get by with T2V & magnifiers most times. however searching threads is a lot harder than for most.
thanks
Lou
PS if you ever cross the tasman drop me a line
loulian, to make it easier to recover from bricks, It would be best if you flashed Hard SPL V7 from here - http://forum.xda-developers.com/showthread.php?t=296722
It won't guarantee a flawless flash but will help if something goes wrong by giving you a GOOD chance of recovery.
You can then use the sd card method and make life easier by not having to worry about pc crashes, cables being pulled, blackouts or those annoying "sync" errros.
Cheers...
Also if you have trouble setting up your Hermes after a flash/hard reset because of the alignment points being hard to see, It would be a good idea to download this -
http://www.codefactory.es/en/downloads.asp?id=44
It will, after you save the settings, allow you to use your PC to set up the Alignment point if you need to Hard Reset or flash your phone making it load the os to the today screen.
zocster said:
Reading helps my friend
Get to bootloader, press ok and power on left and right respectively and stick stylus in all at same time.
that should bring up tricolour screen.
Download your imate jasjam official ROM
EDIT i think you got a dopod so the dopod ROM is what you want from my 4shared or wiki!!
from the wiki or from my 4shared, and flash it while it is in boot loader mode.
then you need to flash hard spl one of the first stickys on this thread that you have just posted to.
Then flash your desired rom.
Click to expand...
Click to collapse
Sorry to ask a stupid question. I have the same problem, but when i try to flush it from a TriColor mode i get a communication error, it complains about activesynch not connected. BTY mine is cingular 8525 so i am trying to use one of the cingular roms.
hi friends,
i have one swisscom xpa s200.
i bought this phone with this problem-when i power on,on the screen is only firs splash screen with ipl/spl=2.20.0001
i tried every WIKI method to recovery this device but no luck.
i dont have one official swisscom xpa s200 rom.
what is the problem,can you help me ?
thanks in advance.
greetings from serbia.
MS
Tell me if it works
Go and try get the original rom then enter bootloader mode to flash.Flashing may only be done on xp computers.Get the original rom from this xda site go 4shared.com or the original phone brand site
how to:
1. charge your device
2. make sure you have activesync installed.. if installed you will see an ActiveSync icon on the lower right part of your desktop right click it click connection settings and UNCHECK allow USB connections then press comm+cam +soft reset button to force your device on bootloader, you should see USB on the lower left screen of your device.
3. Download the NVID_RUU.zip extract it and RUN ( it has only one RUU, so it doesnt matter if your device is G3 or G4 )
4. after flashing the RUU and its succesfull try allowing USB connection again on Active Sync..
5. if its still not working.. try downloading the PV_Temp NVID RUU, i dont have a copy of this so try searching for this in the forums..
goodluck!!
PS: you can also read stiky threads over Prophet Mobile 6 Forum
NVID RUU : http://www.mediafire.com/?0wilzm3vzeo
well, Hard-SPL is released now! sorry for delay, I got distracted elsewhere
[size=+2]NOTE: This is NOT a SIM unlocker - it also doesn't unlock Security for other radios. if you need that, GO HERE[/size]
[size=+2]Donations are always appreciated to the big link in our signature ("elite project"). You can also donate via the link offered in the new Hard-SPL program. Thank you!![/size]
Preparations:
first an important note, if you want to flash more than one Iolite, contact cmonex for additional licenses via http://support.htc-unlocks.com. (the first license is transparently granted and free, so normal users do not need to worry.)
0) this package is for Iolite (Touch Cruise II/2009) devices. for any IOLI***** so far (SSPL loader checks this and gives a warning if needed), afaik there is no CDMA version so all the model variations should be fine.
1) if you have vista, WMDC update is recommended: http://www.microsoft.com/windowsmobile/en-us/help/synchronize/device-center.mspx
Instructions:
read this if unsure how to install Hard-SPL...
1) download latest Hard-SPL package (currently v1.10) from attachment, extract to an empty folder.
2) you must Have Phone Synced with PC in Windows Mobile!!!
3) NEW: internet access is required as the program checks online for updates and license.
4) run Iolite-Hard-SPL EXE on PC, make sure it's launched from a local drive (not through network drive, etc.). if you are on vista, launching as Administrator is strongly recommended, on XP administrator login is required. important: if your AV (norton/symantec mainly) warns about a virus, ignore it, it just doesn't like the packer I used to pack the program.
5) if possible, always use Automatic flash mode (for uses of Manual mode, see troubleshooting section)
6) it will ask you to wait while it prepares for the flashing, press OK. follow steps in the program and then in the RUU.
7) some notes: it should go through without any error messages, if one does pop up, then please follow the instructions included in the error text. if no specific instruction is shown, then ask for help in the thread, but this should not ever occur (as this means a really fatal error occurred).
more notes: when RUU says it will hard reset, do not worry, it is not going to do that. also when it says the flash will take 10 minutes, ignore that, it will only take a minute or so.
8) device should go to a tricolour screen now that says 1.09.C-SSPL, this is the SSPL version, which is temporary.
9) SPL flashes, device automatically reboots, job done.
10) to confirm you got it installed, go into bootloader mode (tricolour screen!) and verify the screen shows 1.09.OliNex, which is the Hard-SPL version.
NOTE: you will not see the SPL version during normal boot, that is the OS version, not SPL!
to enter SPL to check version, fully power the device off by long press of power key, then power on while holding the "volume down" key on the left side of the device. keep holding the volume down key until you see tricolour screen which is the bootloader mode, then release it.
NOTE 2: this is unsigned Hard-SPL. no limitations on flashing ROMs or radio packages. also, this has overwrite protection against HTC RUU's overwriting HSPL with a stock one, so if someone needs to revert to stock SPL for warranty reasons, a stock SPL downgrade package will soon be posted in this post as well. use this relocker *only* if you need to return the phone for warranty, and only use it as last step - after reflashing stock OS and radio. see steps at the end of this post about how to reflash stock SPL.
NOTE 3: do not use this RUU for anything other than SPL flashing (i.e. hardspl or stock spl restore)!!! nothing other than SPL's made by Olinex team (using OliNex custom cert, which is not public) will flash to make SSPL more secure. if you want to flash some other rom, then use shipped RUU or customRUU if you need to flash cooked ROM.
Troubleshooting:
- read the instructions above.
- read the instructions above.
- read the instructions above.
Manual flash mode for USB issues: you should usually go for Automatic flash mode; you must only attempt the Manual mode option if Automatic flash mode or SSPL-Manual.exe already put device in SSPL tricolour screen and you got USB issues. any other errors triggered while running in Autoflash mode will have to be fixed as instructed in the error message.
ModelID checking:
- afaik no CDMA model, so doesn't matter but let me know if you got any problems.
nothing happens on the device, does not enter tricolour screen mode:
- anyone having problems with the device entering SSPL automatically, please make sure you watch the device screen if it asks about running files. also try unchecking advanced usb functionality in settings.
- if it crashes instead of entering SSPL, you need to use Automatic mode.
general usb connection error problems if you get connection error in RUU after the device goes to 1.09.C-SSPL screen:
- try manual SSPL: copy SSPL-Manual-Iolite exe to the device and run it, then when it went to 1.09.C-SSPL tricolour screen and shows "USB" at the bottom in this screen, use Manual option in the Hard-SPL program on the PC.
- make sure device was still synced via USB to the PC at the point of it entering SSPL (the 1.09.C-SSPL screen)!
- try a different USB port
- try different USB cable
- do not touch USB cable during the process especially if it is already a bit dodgy
- also do not use USB hub
- you can also try rebooting your PC
- and you can try using another PC.
- also you can try unticking advanced network functionality in start menu / settings / connections / usbtopc applet.
- another reason for USB connection error: if your PC takes too long to load the drivers (if your device is in bootloader for the first time and perhaps if you are on vista), then if RUU times out, but device still says "USB" on the tricolour screen, just leave it there and re-run the RUU when driver installation finishes.
- finally, you can try disabling antivirus or firewall programs on the PC.
other issues:
- if Enterbootloader.exe fails to run (says missing component or similar), try a hard reset of the device.
- if device reboots instead of going to SSPL screen (1.09.C-SSPL), contact us by PM'ing cmonex. do not PM OliNex user, that is not monitored frequently.
How to reflash Stock/Shipped SPL - STEP BY STEP - FOR WARRANTY REASONS ONLY!:
0. please make sure you already flashed stock ROM and radio, because stock SPL flash is *always* the last step before sending the device in.
1. take the SPL relocker attachment, and run the EXE - this will flash 1.09.0000 stock SPL. simple as that!
2. flash
3. verify if it flashed by checking version in tricolour screen, it should say 1.09.0000.
credits:
first, "OliNex" is a team which means: cmonex + Olipro
Olipro -> EXE program concept that runs on the PC, Hard-SPL concept, server code, maintaining licenses
cmonex -> new PC EXE & SSPL loader for windows mobile and SSPL binary. Hard-SPL binary. (SSPL loader: partially based on haret and old pof&Olipro jumpspl code)
---reserved post---
---reserved---
"IOLI100
SPL-1.09.oliNex
MicroP-Iolite(LED) v5"?
Has it released? It has appeared on the interenet.
Let me see see!
chenjun_conan said:
"IOLI100
SPL-1.09.oliNex
MicroP-Iolite(LED) v5"?
Has it released? It has appeared on the interenet.
Click to expand...
Click to collapse
yes, I've sent it to several people. I'm posting it here too in a sec.
edit: posted
Dan
OK
you are great.
Thank you so much.
Fantastish!
THANK U VERY VERY MUCH!!!
after HSPL and flashing to Rissian ROM it says "Your OS ROM isn' t customized for your hardware Please reflash the proper ROM code or contact the service center' .
In the internet i've read that taking out the battery for 10-15 minutes must help. But it doesn't. Please help!
Great job, big thanks!
@ cmonex was send you a PM, please answer me. Thanks!
Greetings
Baga12 said:
after HSPL and flashing to Rissian ROM it says "Your OS ROM isn' t customized for your hardware Please reflash the proper ROM code or contact the service center' .
In the internet i've read that taking out the battery for 10-15 minutes must help. But it doesn't. Please help!
Click to expand...
Click to collapse
try to flash WWE|Eng and post result here
Nice work as usual guys.
Thread stuck
Dave
After IoliteSPLRelocker, the HSPL' s not working, why? Please help
Thank you
Thank you so much for your hard work.
My Iolite can do do just about anything right now.
Baga12 said:
After IoliteSPLRelocker, the HSPL' s not working, why? Please help
Click to expand...
Click to collapse
You tell us? It what way doesn't it work?
Dave
I tried to test the IoliteSPLRelocker, it flashed correctly, then I again tried to flash the HSPL with mhile my device was in three color mode, but it stops at the 0%, not going more. Stupid of me, of course
So? what about WWE Roms? Does anybody flash them at new HSPL?
thanks very much . it's great'
Baga12 said:
I tried to test the IoliteSPLRelocker, it flashed correctly, then I again tried to flash the HSPL with mhile my device was in three color mode, but it stops at the 0%, not going more. Stupid of me, of course
Click to expand...
Click to collapse
Please help!
max_nya said:
So? what about WWE Roms? Does anybody flash them at new HSPL?
Click to expand...
Click to collapse
Once you have Hard SPL, you can flash any ROM's (Cooked or Shipped) to your device. So put on Hard SPL, find a WWE ROM and flash it .
Baga12 said:
Please help!
Click to expand...
Click to collapse
I've just checked the re-locked and it does contain the correct SPL.
Connect your phone to you PC using AS, and then run the re-locked, once done your SPL should be 1.09 (with the .OliNex) again
Dave