Related
Topic says all
If someone has (or had) the time to make a guide about this it would be nice
prodigyfied said:
Topic says all
If someone has (or had) the time to make a guide about this it would be nice
Click to expand...
Click to collapse
I have got the OS.nb , do you needed?
This can be of use We'll talk in skype about that
I'm also asking about physical disassembly of the device
I took one apart and put the good cover from one with a damaged screen onto the one I had with a scuffed cover.
It was successful but a real pain in the butt.
Take off back cover/battery cover. and unscrew the screws you can see.
Next bit is the hard bit and I just did it by brute force, but you then need to take off the white pearly bit around the camera, as other screws are hidden under there. I just used a small screwdriver and edged my way around the top, but it was pretty firm and took some getting off.
Once that was off, I undid two more screwsand that allowed me to edge off the black section where the battery sits from the main phone bit (green computery hardware bit sorry, I'm not very techy!! ) I again did this slowly but it needed some force as it's very very snugly fitted. There are some black clips as part of this middle section that you can push inwards to release the front with screen and keyboard and reveale the phone inards.
You immediately notice the ribbon attaching the camera to the main motherboard/phone and it pops out . I then unscrewed the 4 tiny tiny screws attaching the screen to the frontof the phone and very gently prised the whole phone guts out and immediately dropped it onto the new front I had ready. Screwed the screen back in place and also one other ribbon plugs into the motherboard from the keyboard Front section.
Trickiest part was re screwing the screen screws as they were teeny and I had to use tweezers to hold em in place. Then replugged in the bottom ribbon (Think it was power button? ) and placed the battery section back on top of the motherboard bit.
Another tricky bit was re attaching the ribbon from the camera as I had to almost close the black battery section and just leave a tiny gap and use the flat end of my tweezers to gently push the ribbon connector in. It's doable but bloomin fiddly.
After that I clicked as much of the battery/middle section back onto the front/screen and keyboard section, but inevitable it's not quite as fixed as it was, and there are signs that it's been taken appart as I found it impossible to take appart with out some force and some of the plastic clips were either bent ir broken in doing it. I screwed the screws back on and put back the white section round the camera - luckily everything started up and worked OK, but I'm sure I could have easily messed it up
Its a very fiddly thing to attempt. I only did it as I'd got two handsets reasonably cheaply and wasn't risking much. But it's a phone that obvioulsy wasn't made with cover changes in mind. LOL Once fully put together again it's robust and no loose bits, and everything working fine.
Daisy xx
i had one of those lovely phones (despite what everyone else says, i loved that mobile) and eventually, after a LOT of use, it became useless so i took it apart. i cant remember how i did it exactly, but it got to the point where i could take the entire thing apart, put enough parts together for it to work and then re-asemble it again. it was a great thing to show to friends at college as none of them really knows whats inside mobiles there.
i miss that phone
then again, i now have a vox
At last...
So glad to see someone has written down a guide on how to take the Lobster apart. I have been trying to dismantle mine and can only see me breaking it as I can't see any way in. I will try your step by step guide daisy...thanks for that. I'm also a proud owner of a vox now but I do have miss my Lobster and would quite happily use it again if need be. Thats if I can get it apart and fix it of course!
Thanks Dayzee, nice article
if anyone puts apart their lobby soon, please make some photos, and share them here, I think it'd be useful too
Does anyone know if there is a third party Touch HD cover with a reset hole, so that we can perform reset wihtout having to remove the back cover?
I usually try to reset by software, but often this is not possible because the device is frozen, in which case I would remove the back cover and take off the battery.
How much more convenience there will be if I can just poke into the reset hold without removing the cover, isn't it?
why not just drill the cover yourself?
What tools do you use for this drilling job? How do you get it at the correct position? Will the paint around it come off if an amateur does the drilling?
I would love one with micro SD card hole. But I would need an extra back cover to have that as backup.
Try it with one of these: http://cgi.ebay.co.uk/Housing-Batte...3286.c0.m14&_trkparms=66:2|65:2|39:1|240:1318
It is a relatively simple task drilling a hole, or making a cut-out.
I would suggest buying a spare back cover first though.
You will need;
something like a 2.5mm drill bit (just got HD like an hr ago not had chance to play with it or make measurements), 2 bits of masking tape, a small ruler or measuring tape, something to protect the back when laying it on a suitable surface to drill on.
Accurately measure where the button is in relation to where the hole is to be.
Put the Masking tape either side of the back roughly where the hole will be, then carefully transfer the measurements over on to the back and mark on the tape where the hole will be.
Using a suitable bit, while resting the back on something to prevent scratches, drill the hole.
Please note having a hole may increase chances of dust and lint getting into the battery compartment - you could resolve this by getting a small 10mm square piece of foam (same kind as used in light traps in cameras - its pretty thin).
For the Micro SD cut out, sorry you'll need to ask me later once I've had a chance to have a proper look.
Feel free to PM me
It is a relatively simple task drilling a hole, or making a cut-out.
I would suggest buying a spare back cover first though.
You will need;
something like a 2.5mm drill bit (just got HD like an hr ago not had chance to play with it or make measurements), 2 bits of masking tape, a small ruler or measuring tape, something to protect the back when laying it on a suitable surface to drill on.
Accurately measure where the button is in relation to where the hole is to be.
Put the Masking tape either side of the back roughly where the hole will be, then carefully transfer the measurements over on to the back and mark on the tape where the hole will be.
Using a suitable bit, while resting the back on something to prevent scratches, drill the hole.
Please note having a hole may increase chances of dust and lint getting into the battery compartment - you could resolve this by getting a small 10mm square piece of foam (same kind as used in light traps in cameras - its pretty thin).
For the Micro SD cut out, sorry you'll need to ask me later once I've had a chance to have a proper look.
Feel free to PM me
As above & using my trusty Dremmel in its drill press to get an accurate location.
Although, I'm also not too keen to have an 'open' hole on my case.
For an micro SD cut out cover, suppose you could use a small piece of sheet rubber: leave 2 lugs either side to secure the flap when closed and secure the flap to the back.
Or you could perform something approaching micro surgery and construct a carrier for it that replacesthe bit cut out for the hole.
why not install
holyfox's_poweroff-diamond.cab
ljazzo1 said:
why not install
holyfox's_poweroff-diamond.cab
Click to expand...
Click to collapse
Read the first post - he wants this for when the device is frozen and a software reset would not be possible.
iPhoneLCD superior to Blackstone! but Blackstone practical than the iPhone!
I just bought a Boxwave 2500mah extended battery that comes with a extended battery door for my Touch HD and I think its pretty easy & possible to make reset hole for the battery door. You just need a really pointy and sharp exacto knife to puncture the plastic battery door and then just rotate the knife until you get your desired size of the hole. Tried this many times when I was still playing with "Lets Go Tamiya Cars".
About the hole for the microSD card, I think this one will be a little tricky to do because you might hit one of the locks for the door upon modification.
eaglesteve said:
Does anyone know if there is a third party Touch HD cover with a reset hole, so that we can perform reset wihtout having to remove the back cover?
I usually try to reset by software, but often this is not possible because the device is frozen, in which case I would remove the back cover and take off the battery.
How much more convenience there will be if I can just poke into the reset hold without removing the cover, isn't it?
Click to expand...
Click to collapse
Hi eaglesteve,
If the device is frozen, can't you just reset by holding the power key down for 3 seconds? This should always kill the power, leading to a soft reset when you turn it back on. It's my preferred method for tboth the Blackstone and Diamond products.
mike.waters said:
Hi eaglesteve,
If the device is frozen, can't you just reset by holding the power key down for 3 seconds? This should always kill the power, leading to a soft reset when you turn it back on. It's my preferred method for tboth the Blackstone and Diamond products.
Click to expand...
Click to collapse
The problem is that the Blackstone requires a touch confirmation and this is usually not possible when the device is frozen.
Hi,like this ?
Marcdu81 said:
Hi,like this ?
Click to expand...
Click to collapse
this is crazy... why are u people drilling the cover when u can slide it out normally ...
Hi,
Where i can find a back cover with reset hole?
Thanx
I think you will have to buy a replacement battery cover and drill a hole in it yourself
Hey Everyone.
While sitting on my living room floor, I dropped my Prime & Dock from about a foot high onto the carpet. Murphy's Law: Gravity will always exert a greater force on the weakest part of your device. The Prime landed on the charging connector. I thought for sure the wire itself would be kinked up and broken (My mind is racing: "can I get a new cable from somewhere in less than 18 hours?! Argh!") As it turns out, the cable was fine, but the port itself was broken.
The little plastic comb that separates the upper pins from the lower pins was broken and had fallen out. I figured I would have to send the dock into Asus to be repaired one way or another, so I thought I'd take a stab at a repair. I used my smallest two flathead screwdrivers (PC-repair sized) to gently bend the upper pins further up and the lower pins lower down. I describe how little of an adjustment I'm talking about here- it has to create just enough room for you to slip the comb piece back in, but not be so much that the charge wire won't flatten them back down when you first connect it.
To make the comb stick, I used the smallest imaginable amount of superglue at either end of the comb piece. It seems the plastic is a little thicker there and there aren't any pins (that might get coated with glue) at the very ends. I used small needle-nose pliers to insert the comb and held it tight for a few seconds. I then put the dock in position so that the comb was facing straight up, so that gravity (grrr) wouldn't pull the comb piece down out of perfect vertical alignment while the glue cured. I left it overnight just to be safe.
Next morning, I plugged in the power connector and all was well. I've probably plugged and unplugged it 20 times or so now, and it feels reasonably solid. Mind you, I have NO doubt that this fix is temporary. The second I trip on the power cord or forget to be gentle with the device that superglue is going to let go. At that point maybe I'll send the dock off for repair. I just couldn't part with it this early on, knowing Asus is dealing with about a zillion more important fish to fry right now.
So, If you happen to have the same problem- give some glue a shot. It worked for me!
Kudos! I can't ask you to recreate and photo lol
But if anyone else runs into this, please take some macros of the process to give people a good idea of just how much bending of the pins is needed.
Naturally. I thought of taking pictures the next morning after everything was working again.
If the comb breaks out again, I'll probably attempt one more repair before I send it to Asus. If and when that happens I'll post up some pics.
As far as the bending of pins, I just pressed gently and tried to insert the comb piece with pliers. If it seemed too difficult to do with glue on the broken piece, I just set it down and pried on the pins a bit more. I guess if you looked at them, you would have been hard-pressed to tell if they were any wider than normal. The telling fact was being able to slide the broken piece back into the pins fairly easily. Once I could do that, I actually applied the glue, inserted the piece, and let it set up.
So as many people here know, the rear camera is a sore point on the Transformer Prime, in that it's known to go bad early and often. Not to beat a dead horse, here's how we fix the situation:
Replacing the rear camera module:
Yes it seems logical that this would be all you would need, but I've just confirmed myself that in fact it is only the camera module with a problem. The main issue with the fix is FINDING a good camera. I was a bit discouraged on my first attempt as I bought a rear camera on ebay listed as "working" from a parted out Transformer Prime only to go to the hassle of installing it and it not working. I can't say I was surprised, but after trying to find one for so long I took the chance. Upon recieving my refund, I purchased another rear webcam that surprisingly also surfaced. The seller for this second camera had TONS of feedback, and mostly products with the word "foxconn" in the title, indicating this guy seems to have a line on foxconn surplus parts, which for us is awesome. The camera I received appears to be brand new and fired up immediately! Not trying to push a particular seller but since many people are probably looking for this part, I'll post the link http://www.ebay.com/itm/Asus-Eee-Pa...?pt=US_Tablet_Accessories&hash=item416a33f1f9. The seller is skyline27 and he appears to have one left right now (I bought the second). NOW, enough theory, onto the howto.
HOWTO (the good stuff)
0. Turn off Tablet (thanks whycali)
1. Remove screen as instructed in other disassembly threads (wifi fix threads, etc) Advice for this includes working from the bottom first, being vary carefly to NEVER use the pry tool at either the latch holes or the bottom port, as these very thin pieces of aluminum will bend. Get your tool in (heh heh) to the left or right of these "holes" in the case, then slide the tool sideways past them to avoid prying outwards. Get the entire bottom free, then slowly work up the sides with your plastic tools/credit card. When you get to the top, try gently pulling the screen "Down" or the port. You can also pull up like the rest, but when I disassembled I saw what looked like "hooks" that made me want to slide the top out last by pulling it towards the dock port.
1.2 (I forgot) Flip switch on right side of motherboard (top board) that will disconnect power to the motherboard before disconnecting the battery. Don't forget to switch it back when finished, or it won't turn on. (thanks whycali)
1.5 (I forgot) unscrew and remove flash and microphone at top
2. You can either disconnect the screen ribbon cable from the motherboard *top board* (makes your life easier) or simply set the screen upside down, rotated 90, and to the left of the opened prime. This allows the cables to sit fairly easily, though since you'll be removing the motherboard anyways it may be easier to unplug
3. Unscrew 8 battery screws, carefully unplug wide connector (I used precision flathead to the left and right of plug as to not 'yank'). Set battery aside.
4. Be sure every cable is unplugged from the Motherboard. This includes a small battery on the left side, the power button/volume cable top left, as well as the speaker cable on the right side.
5. Remove all motherboard screws. Be sure you get them all, you don't want to snap the motherboard in half in a minute because we'll be pulling against a little adhesive.
6. Be careful. REMOVE MOTHERBOARD This is the step you're most likely to have an issue, but it's still really easy. Time to remove the motherboard. This is easy if you know what to expect.
6a Both cameras are slightly adhesived into their holes, also plugged to back of motherboard. You can either try and pull these with the mobo, or let them stay where they are and pull them out later (probably easier for beginners)
6b There is a thermal pad about 1/3 away from the left where the CPU is. It is a bit adhesive, but not too much
6c MOST IMPORTANT - The motherboard is sort of "sandwiched" into the ports on the sides. That is, it doesn't want to pull straight up and out, the hdmi and headphone jacks are in the way. I believe it's very easy to break the HDMI and/or headphone jack here, yet I haven't yet. 2 ways to approach, one is to pull the side of the tablet outward slightly at the headphone jack to slide it up, allowing you to lift that side of the board, then sliding to the right to clear the hdmi. The second method which I prefer, is pulling up on the mobo from the center, causing the outer edges to pull inward slightly as the board flexes a bit. Choose whichever you prefer
7. Replace the camera. If you're this far along, I really shouldn't have to explain this. The front and rear sit side by side, your front is probably good, there's a piece of tape over the connectors, pull up, replace rear, make sure plugged in firmly on both, replace tape.
Installation is reverse of removal. I recommend plugging the screen ribbon (and all ribbon cables) into the motherboard before reinstalling it, as the connectors are on the bottom of the board and very difficult to get at once installed in the prime. Again, flex the motherboard or prime slightly to clear the ports going back in. Be sure cameras are attached to the motherboard, when installing, be sure to double check one last time that they're still plugged into the board before putting the board down and letting the cameras sit in their plastic holders. And don't forget that internal power switch on the right side of the motherboard.
FWIW, and I'm sure many will disagree with me, but I typically check everything before snapping the screen back up by booting it up with a few sheets of paper between the screen and internals as an extra safety insulator. Check screen, touch screen, both cameras, SD card, speaker, then I snap it shut.
If anyone really needs pictures I think I have a few, though not really specifically of what I was doing, but I could highlight/circle the pics I have if anyone gets stuck.
I really hope I can help others get a working camera who can't/won't RMA for the issue. Now time to UNLOCK MUAHAHAHA!!!
One thing I mostly remember to do when I plan to disassemble the ribbon cables is to turn off the internal power switch first.
I know this is an older thread but does anybody know where to get a new camera. The one that is linked to in the above post is no longer available. Thanks
Sent from my Transformer Prime TF201 using Tapatalk 2
Just 35 minutes ago my phone fell from my hands and onto some cable in the perfect way that it broke the Digitizer. Wonderful. So now I have to go about replacing this. It looks pretty straightforward and I will be doing this but I have a few questions I'd like to see if I can get answered. Perhaps this can be used by others as a helpful FAQ regarding replacing the LCD or Digitizer on an HTC Rezound.
1) I know I will be needing the Digitizer only as the LCD portion is not broken, so can anyone give me a good reason why I should replace both and not just the digitizer?
2) I know there are some adhesives involved in holding it together. Are these re-usable or should they be replaced? If they should be replaced, what kind of adhesives are they and where can they be found?
3) What is a good source for these parts? (Adhesives and digitizer)
4) Is there upgrades here I can do? Like a gorilla glass digitizer or something?
5) I've read a guitar pick is a great tool to separate parts, do you agree?
6) Any Gothca's that I should be concerned about
Here is the procedures I will be following:
1) Remove the back cover, the battery, SIM card and SD Card
2) Remove the 6 T5 torx screws around the sides (from the back)
3) Pry up the back by releasing the plastic clips around all 4 sides (note the volume rocker/power button may fall out)
4) Remove the Vibrator motor
5) Remove the two screws holding the MoBo on and lift up from the USB port side and remove the plastic piece from there.
6) Release the small plastic clips holding the Mobo in and swing it up, release the two ribbon cable connections
7) Heat around all sides front and back to loosen the adhesive, from the back work with a guitar pick to loosen the adhesive, repeat this process from the front.
8) Work around with the guitar pick between the screen and the housing from the front and remove the LCD and digitizer from the housing
9) Heat all the sides of the LCD/digitizer to loosen the Adhesive
10) Work with the guitar pick around the sides to release the digitizer from the LCD screen. It seems there is a piece of black tape on one side, you would have to "butterfly" the two screens and peel the screens apart.
11) Done. Reverse these steps to rebuild it. Do these adhesive parts need the adhesive replaced? Does the tape need to be replaced?
I cannot post links yet, but I felt I should give credit where its due. To obtain these steps I used a Youtube video. To view this video, search youtube for: 'How To Fix HTC Rezound Screen by RepairsUniverse.com'
The advice from the experts is highly anticipated!!
Regards,
Eduard Tieseler
The best reason for replacing both is that you won't have to worry about binding them or getting dust between them if you get them together preassembled. As to the rest, I can't say. I know we have a few people here who have done it.
So I found the adhesive strips that I need. It comes as a bulk sheet where you cut them to fit. I am going with replacing only the digitizer. Replacing the LCD screen also would male the process easier however I fear getting a replacement screen that is in worse shape or more poorly made than the original one my phone came with. I know this one has no flaws.
So I have answered my questions already. I'll post here when I done replacing the digitizer with anything that is of interest in case someone else has questions about this procedure.
Thank you for your input shrike1978. Much appreciated.
Regards,
Eduard Tieseler
Sent from my Infected HTC Rezound using xda app-developers app
etieseler said:
Just 35 minutes ago my phone fell from my hands and onto some cable in the perfect way that it broke the Digitizer. Wonderful. So now I have to go about replacing this. It looks pretty straightforward and I will be doing this but I have a few questions I'd like to see if I can get answered. Perhaps this can be used by others as a helpful FAQ regarding replacing the LCD or Digitizer on an HTC Rezound.
1) I know I will be needing the Digitizer only as the LCD portion is not broken, so can anyone give me a good reason why I should replace both and not just the digitizer?
2) I know there are some adhesives involved in holding it together. Are these re-usable or should they be replaced? If they should be replaced, what kind of adhesives are they and where can they be found?
3) What is a good source for these parts? (Adhesives and digitizer)
4) Is there upgrades here I can do? Like a gorilla glass digitizer or something?
5) I've read a guitar pick is a great tool to separate parts, do you agree?
6) Any Gothca's that I should be concerned about
Here is the procedures I will be following:
1) Remove the back cover, the battery, SIM card and SD Card
2) Remove the 6 T5 torx screws around the sides (from the back)
3) Pry up the back by releasing the plastic clips around all 4 sides (note the volume rocker/power button may fall out)
4) Remove the Vibrator motor
5) Remove the two screws holding the MoBo on and lift up from the USB port side and remove the plastic piece from there.
6) Release the small plastic clips holding the Mobo in and swing it up, release the two ribbon cable connections
7) Heat around all sides front and back to loosen the adhesive, from the back work with a guitar pick to loosen the adhesive, repeat this process from the front.
8) Work around with the guitar pick between the screen and the housing from the front and remove the LCD and digitizer from the housing
9) Heat all the sides of the LCD/digitizer to loosen the Adhesive
10) Work with the guitar pick around the sides to release the digitizer from the LCD screen. It seems there is a piece of black tape on one side, you would have to "butterfly" the two screens and peel the screens apart.
11) Done. Reverse these steps to rebuild it. Do these adhesive parts need the adhesive replaced? Does the tape need to be replaced?
I cannot post links yet, but I felt I should give credit where its due. To obtain these steps I used a Youtube video. To view this video, search youtube for: 'How To Fix HTC Rezound Screen by RepairsUniverse.com'
The advice from the experts is highly anticipated!!
Regards,
Eduard Tieseler
Click to expand...
Click to collapse
Check out my thread: http://forum.xda-developers.com/showthread.php?t=2189789
I did it not long ago, and was fine. However, I opted to go for the digitizer + LCD assembly, as I didn't want to have to worry about separating the digitizer from the LCD and worrying about dust.
To answer your questions:
1) It's eaiser, takes less time, and you don't have to worry about dust with replacing the digitizer + LCD assembly.
2) Replace the adhesive. I tried reusing it... and it has some flex on it. So I got some new adhesive, scraped the old stuff off, put the new one, and used a heatgun to move the screen assembly around to get it to fit right, and then pressed it down as it cooled to secure it better.
3) Ebay
4) Not sure on this one... not that I know of anyway.
5) If you get the parts from eBay, then they sometimes come with tools (Torx, philips, and a plastic separator tool).
I also linked the video that I used in my thread, so you can look at that. It's pretty straightforward and easy to do. Took me about 45 minutes to just over an hour to do everything, as I was taking my time.
Well I did this process two days ago and for the most part it went well, but not without its issues.
First off, I should have heeded the advice of others suggesting to get the LCD + Digitizer pre-assembled. I tried to save some money however now there is a dead spot on my phone and I will have to spend that extra money to buy the kit anyways. So for anyone else thinking they can get away with just the digitizer, unless you have dustless neoprene gloves and a clean room (or possibly nitrogen or canned air) and lots of experience, do not attempt to replace one or the other, just get the pre-assembled kit.
I am going to replace it again with the kit in a few more days.
The only thing that came up that I didn't see anywhere else, was when I was pulling the back cover off. The spot where the camera is located was kind of sticking to the back cover. If I would have pulled to quickly or was too rough I would have easily damaged the camera. So my advice would be to work slowly when pulling the back cover off. If it feels like its resisting, it could be your camera. Wiggle it slightly and don't force it. The camera will loosen itself from the back case, but using too much force you could damage it.
Thanks for the info guys! :good:
etieseler said:
Well I did this process two days ago and for the most part it went well, but not without its issues.
First off, I should have heeded the advice of others suggesting to get the LCD + Digitizer pre-assembled. I tried to save some money however now there is a dead spot on my phone and I will have to spend that extra money to buy the kit anyways. So for anyone else thinking they can get away with just the digitizer, unless you have dustless neoprene gloves and a clean room (or possibly nitrogen or canned air) and lots of experience, do not attempt to replace one or the other, just get the pre-assembled kit.
I am going to replace it again with the kit in a few more days.
The only thing that came up that I didn't see anywhere else, was when I was pulling the back cover off. The spot where the camera is located was kind of sticking to the back cover. If I would have pulled to quickly or was too rough I would have easily damaged the camera. So my advice would be to work slowly when pulling the back cover off. If it feels like its resisting, it could be your camera. Wiggle it slightly and don't force it. The camera will loosen itself from the back case, but using too much force you could damage it.
Thanks for the info guys! :good:
Click to expand...
Click to collapse
I also purchased the full assembly and was able to switch the new parts onto my Rezound. Unfortunately, the earpiece (the part you listen to when NOT on speakerphone) and the proximity sensor did not work with the new set, and I am swapping it for a replacement. However, I've been inside the unit now 5 times, and I suggest in addition to the tools supplied with the sets (t5, small phillips and separator) you also have a small flathead (helps with starting the split the unit apart and also with pulling and reattaching the vibrator motor) and a long tweezers (invaluable when trying to reconnect the ribbon cables.)
Also, reconnect the MIDDLE ribbon cable (which is slightly twisted and longer) first, then reconnect the top, and don't forget to reapply the insulating tape (been there, done that).
Watch the take apart video on Youtube repeatedly until you can do it with your eyes closed, and be careful, the red plastic does break easily, especially on the corners.
Replaced my digitizer with good success, using new adhesive. Upon first re-assembly the digitizer was popping out of the plastic bezel a bit, but everything worked great, touch, display, everything. So I decided to take apart, add some more adhesive strips. Now the digitizer stays flush.
First boot after 2nd re-assembly, got boot with first vibrate, but no screen on. So I pull the battery to attempt again. Now I receive no vibrate response from power button. When plug into charger, orange light comes on for 5 seconds and then off indefinitely. This happens each time after battery pull+wall charger plugin.
I have tried multiple times disassembling, checking both ribbon cables that plugin to motherboard, appear to connect fine. Visually all other aspects of MB appear fine.
Any ideas anyone? Not sure what may have broke. I should have left well-enough alone, but the digitizer was somewhat spongey to touch on right side of screen and I could see white light shine up... TIA
Each time I pull the batt the orange light will come on solid for 5 or so sec, then off for good. One time even started flashing for a bit like it was charging from full depletion (like it does before it lets you power on). Not sure how to diagnose.
Did you make sure to put the yellow protective tape over the ribbon cable connections? When you open it (like a book) and see two ribbon cables. There originally was a small piece of tape over the connection to provide protection from anything being shorted out. Make sure this is back on.
If you no longer have the tape, I think any non-conductive tape would work like plain Scotch tape. Please correct me if I am wrong in that statement.
Sent from my Infected HTC Rezound using xda app-developers app
etieseler said:
Did you make sure to put the yellow protective tape over the ribbon cable connections? When you open it (like a book) and see two ribbon cables. There originally was a small piece of tape over the connection to provide protection from anything being shorted out. Make sure this is back on.
If you no longer have the tape, I think any non-conductive tape would work like plain Scotch tape. Please correct me if I am wrong in that statement.
Sent from my Infected HTC Rezound using xda app-developers app
Click to expand...
Click to collapse
I did not put those pieces of tape back on. In the YouTube video by "injured gadgets," I don't believe they re-covered up those ribbon cable plugins, so I also did not during re-assembly. Should I try that? Or, I assume, my board somewhere has gone bad? (Phone did work just fine after re-assemble, until I decided to take apart again)
And after doing this a handful of times, I figured out that the "earpiece" doesn't come with the digitizer/LCD/housing. It has to be pulled from the old phone and moved to the new one. Once I did that, everything was fine.
hgoldner said:
And after doing this a handful of times, I figured out that the "earpiece" doesn't come with the digitizer/LCD/housing. It has to be pulled from the old phone and moved to the new one. Once I did that, everything was fine.
Click to expand...
Click to collapse
hgoldner, when you had forgotten to re-apply the insulating tape over the ribbon cables, did that result in a toasted motherboard? I'm trying to find out if that's what happened to mine? Thx
red3razor said:
hgoldner, when you had forgotten to re-apply the insulating tape over the ribbon cables, did that result in a toasted motherboard? I'm trying to find out if that's what happened to mine? Thx
Click to expand...
Click to collapse
I would go ahead and try putting it back on. There was an earlier post where someone mentioned it was important to put it back on, perhaps he can comment on what can happen if its not on (He said he learned from experience). Perhaps you can PM him.
To be honest, I originally only put the tape back on one connection, but after the second time replacing both the LCD screen and the digitizer, I found the second piece of tape and now both are back on.
What can it hurt to see if that will fix it? Its fairly easy to get to on these phones.
Ed
Yes I did try put back on, no worky still. I assume motherboard issues now. So now I ask if anyone that has also failed to put tape insulation back on, has also resulted in motherboard fail?
red3razor said:
Yes I did try put back on, no worky still. I assume motherboard issues now. So now I ask if anyone that has also failed to put tape insulation back on, has also resulted in motherboard fail?
Click to expand...
Click to collapse
I ran it for about a week or so without the insulating tape. I assume you just mean the translucent, amber tape that goes over the jaw connectors of the ribbon cables on the motherboard? Not putting that on shouldn't have damaged your board... it's really just there to keep the jaw connectors from opening from vibrations.
carngeX said:
I ran it for about a week or so without the insulating tape. I assume you just mean the translucent, amber tape that goes over the jaw connectors of the ribbon cables on the motherboard? Not putting that on shouldn't have damaged your board... it's really just there to keep the jaw connectors from opening from vibrations.
Click to expand...
Click to collapse
I left it off on one connection for about a week also with no issues. However I did notice roughly a 16th of an inch of copper exposed on the ribbon. I can envision potential issues from that. I'm not sure about your phone, but the jaw connectors on mine would never open on their own. Far too much resistance to open from any vibration or movement. The vibrator motor connection had a better chance of disconnecting on its own than the ribbon cables. I'm sure that tape provides more than just locking the jaw connectors closed. I could be wrong though.
red3razor said:
hgoldner, when you had forgotten to re-apply the insulating tape over the ribbon cables, did that result in a toasted motherboard? I'm trying to find out if that's what happened to mine? Thx
Click to expand...
Click to collapse
No, I remembered and put it on before I powered up.
Dumped down the innertubes from my Asus Transformer TF300T
Just replaced my digitizer two days ago and I must add the difference is like night and day. I noted in a post that I had tripped and fell on it with my knee...lol ..nope.. I threw the damn thing and it hit the wall. Yahhh.. I know stupid lol... Something really pi$$ed me off tho and I kinda lost it.. .poooof....... Anyway, I had about 30 cracks in my digitizer and amazingly it still worked. Replaced it two days ago and it works great.
That factory adhesive is some SERIOUS stuff. I have performed many electronics repairs over the years and this...well...removing the digitizer and applying the new strips in exactly the right size was a royal pain in the a**! You REALLY gotta get that digitizer glass HOT if you want to be able to loosen it. Light heating WONT do squat to it. And the new strips arent even half as strong as the factory stuff. You really need patience and precision here.
Yes, dust ISVan issue where I live. Canned air came VERY useful. Also its good to have isopropyl alcohol and soft paper towels so you can clean any smudges you make on the LCD before reapplying the digitizer glass. Basically it's best to blow air over it quickly as you press the digi down to the adhesive. That makes sure every bit of contaminant is out.
About the ribbon cables, no I didn't reapply the amber tape to the jawbone connectors. Much of their adhesiveness was lost when I pulled them off. And as long as the ribbon cables are seated in properly and the jawbone connectors are securely locked down, they wont come disconnected. The tape is only there as an additional measure to secure the jawbone connectors from unlocking. Unless you drop your phone on concrete a lot, those cables arent coming loose....even then, dropping it wouldnt knock those loose.. Its more secure than you think. As far as the phone NOT working, the orange tape would have NO effect on that. Maybe one of your cables were partially disconnected and shorted out something on the mainboard. Either that, or it is static sensitive. Its possible if anything is CMOS.
ONLY issue I have since the repair is the top of the digitizer keeps pushing up because of the digitizer ribbon cable and where you have to bend and fold it in that groove to guide it behind the LCD . The ribbon isnt pinching down well and acts as a spring on the digitizer glass....adhesive not doing anything for that.
oh, did you all remove and reapply the clear (4 button tabs) at the bottom to the new glass? got mine in (the lights are pink now ...weeee ) Had to use some Gorilla super glue to restick them. That adhesive at the bottom was super strong and somehow they lost their stickiness when I pulled them off.
Digitizer after I finally got it unstuck from the LCD... wheewww damn. Lots of cracks. Thats what happens when the phone face eats the wall.....
So, my 4 soft keys on the bottom have yet out. Would fixing the digitzer get them back to working? My screens just got cracked like 2 days ago too, and I just want to make sure before i do all this and then find out i gotta take it all apart again. Thanks in Advance!