Related
the data connector on the missus' new phone is *way* too stiff. I'm convinced it's going to break at some point.
Is there anything that can be done to make it fit a little less snugly? i thought it'd get better over time but it hasn't so far...
I know what you mean, if you look on the back of the plug you will see a little dimple of metal sticking up that does the locking part. What I did was very carefully file it flat and now the plug just slips in easily, it is very small so be careful with filing it down.
mine broke indeed... it pulled out with the charger... ended up putting a new core in from a parts phone off ebay... had to unlock, etc though... good call with the filing...
did the exact same thing batfrog,but I used the rough edge of a flathead screwdriver.Whenever I get to open the phone I might go in there and put in some epoxy behind the connector for kicks....
Unless you are swinging the phone around your head like a lasso..the connector is way too tight..it almost seems like it was designed to break..planned obsolescence anyone?
Does anyone know how to take a G-Tab apart and repair a broken power connector? My son pulled it off of the table where it was charging and it landed squarely on the adapter where it was plugged into the GTab. Everything else works, but charging, of course, does not.
stalnakerz said:
Does anyone know how to take a G-Tab apart and repair a broken power connector? My son pulled it off of the table where it was charging and it landed squarely on the adapter where it was plugged into the GTab. Everything else works, but charging, of course, does not.
Click to expand...
Click to collapse
Buy a dock, that's what I did
stalnakerz said:
Does anyone know how to take a G-Tab apart and repair a broken power connector? My son pulled it off of the table where it was charging and it landed squarely on the adapter where it was plugged into the GTab. Everything else works, but charging, of course, does not.
Click to expand...
Click to collapse
Choice 1: Buy a dock.
Choice 2: Open it up and solder it back in.
Choice 3: Sell your son to a slave labor camp and use the money to buy a new tablet.
Stolen from another forum about performing a hardware reset:
Disassemble the tablet. Remove the four rubber stoppers on the bottom of the tablet (put them aside). Next, unscrew the screws under them (keep those too). Next we need to get the back half of the tablet off. Put the tablet face down on a piece of paper or another protective material. Gently work one corner of the tablet until the two halves are slightly separated, then use something thin like a business card to keep them slightly parted. You can then use something thin and strong, like a plastic gift card to zip around the edges and break the seal. Prying will only damage your plastics.
snowzach said:
Stolen from another forum about performing a hardware reset:
Disassemble the tablet. Remove the four rubber stoppers on the bottom of the tablet (put them aside). Next, unscrew the screws under them (keep those too). Next we need to get the back half of the tablet off. Put the tablet face down on a piece of paper or another protective material. Gently work one corner of the tablet until the two halves are slightly separated, then use something thin like a business card to keep them slightly parted. You can then use something thin and strong, like a plastic gift card to zip around the edges and break the seal. Prying will only damage your plastics.
Click to expand...
Click to collapse
pulling it apart is one thing, resoldering the connection is another. I've read that it's really tricky (and small) Mine started acting up, had to have the plug on a weird angle for the tablet ot start charging. I thought it was the chord, but it must be the hardware inside the tablet that caused it. I bought a dock, and a second charger...the dock works BEAUTIFULLY for charging, and for watching movies on the big screen via the HDMI port on the dock...
Viewsonic G connector input jack power jack
If you need to replace the jack, you can get it at Ebay.....just type in Viewsonic G jack or power jack and they have them there.
So as many people here know, the rear camera is a sore point on the Transformer Prime, in that it's known to go bad early and often. Not to beat a dead horse, here's how we fix the situation:
Replacing the rear camera module:
Yes it seems logical that this would be all you would need, but I've just confirmed myself that in fact it is only the camera module with a problem. The main issue with the fix is FINDING a good camera. I was a bit discouraged on my first attempt as I bought a rear camera on ebay listed as "working" from a parted out Transformer Prime only to go to the hassle of installing it and it not working. I can't say I was surprised, but after trying to find one for so long I took the chance. Upon recieving my refund, I purchased another rear webcam that surprisingly also surfaced. The seller for this second camera had TONS of feedback, and mostly products with the word "foxconn" in the title, indicating this guy seems to have a line on foxconn surplus parts, which for us is awesome. The camera I received appears to be brand new and fired up immediately! Not trying to push a particular seller but since many people are probably looking for this part, I'll post the link http://www.ebay.com/itm/Asus-Eee-Pa...?pt=US_Tablet_Accessories&hash=item416a33f1f9. The seller is skyline27 and he appears to have one left right now (I bought the second). NOW, enough theory, onto the howto.
HOWTO (the good stuff)
0. Turn off Tablet (thanks whycali)
1. Remove screen as instructed in other disassembly threads (wifi fix threads, etc) Advice for this includes working from the bottom first, being vary carefly to NEVER use the pry tool at either the latch holes or the bottom port, as these very thin pieces of aluminum will bend. Get your tool in (heh heh) to the left or right of these "holes" in the case, then slide the tool sideways past them to avoid prying outwards. Get the entire bottom free, then slowly work up the sides with your plastic tools/credit card. When you get to the top, try gently pulling the screen "Down" or the port. You can also pull up like the rest, but when I disassembled I saw what looked like "hooks" that made me want to slide the top out last by pulling it towards the dock port.
1.2 (I forgot) Flip switch on right side of motherboard (top board) that will disconnect power to the motherboard before disconnecting the battery. Don't forget to switch it back when finished, or it won't turn on. (thanks whycali)
1.5 (I forgot) unscrew and remove flash and microphone at top
2. You can either disconnect the screen ribbon cable from the motherboard *top board* (makes your life easier) or simply set the screen upside down, rotated 90, and to the left of the opened prime. This allows the cables to sit fairly easily, though since you'll be removing the motherboard anyways it may be easier to unplug
3. Unscrew 8 battery screws, carefully unplug wide connector (I used precision flathead to the left and right of plug as to not 'yank'). Set battery aside.
4. Be sure every cable is unplugged from the Motherboard. This includes a small battery on the left side, the power button/volume cable top left, as well as the speaker cable on the right side.
5. Remove all motherboard screws. Be sure you get them all, you don't want to snap the motherboard in half in a minute because we'll be pulling against a little adhesive.
6. Be careful. REMOVE MOTHERBOARD This is the step you're most likely to have an issue, but it's still really easy. Time to remove the motherboard. This is easy if you know what to expect.
6a Both cameras are slightly adhesived into their holes, also plugged to back of motherboard. You can either try and pull these with the mobo, or let them stay where they are and pull them out later (probably easier for beginners)
6b There is a thermal pad about 1/3 away from the left where the CPU is. It is a bit adhesive, but not too much
6c MOST IMPORTANT - The motherboard is sort of "sandwiched" into the ports on the sides. That is, it doesn't want to pull straight up and out, the hdmi and headphone jacks are in the way. I believe it's very easy to break the HDMI and/or headphone jack here, yet I haven't yet. 2 ways to approach, one is to pull the side of the tablet outward slightly at the headphone jack to slide it up, allowing you to lift that side of the board, then sliding to the right to clear the hdmi. The second method which I prefer, is pulling up on the mobo from the center, causing the outer edges to pull inward slightly as the board flexes a bit. Choose whichever you prefer
7. Replace the camera. If you're this far along, I really shouldn't have to explain this. The front and rear sit side by side, your front is probably good, there's a piece of tape over the connectors, pull up, replace rear, make sure plugged in firmly on both, replace tape.
Installation is reverse of removal. I recommend plugging the screen ribbon (and all ribbon cables) into the motherboard before reinstalling it, as the connectors are on the bottom of the board and very difficult to get at once installed in the prime. Again, flex the motherboard or prime slightly to clear the ports going back in. Be sure cameras are attached to the motherboard, when installing, be sure to double check one last time that they're still plugged into the board before putting the board down and letting the cameras sit in their plastic holders. And don't forget that internal power switch on the right side of the motherboard.
FWIW, and I'm sure many will disagree with me, but I typically check everything before snapping the screen back up by booting it up with a few sheets of paper between the screen and internals as an extra safety insulator. Check screen, touch screen, both cameras, SD card, speaker, then I snap it shut.
If anyone really needs pictures I think I have a few, though not really specifically of what I was doing, but I could highlight/circle the pics I have if anyone gets stuck.
I really hope I can help others get a working camera who can't/won't RMA for the issue. Now time to UNLOCK MUAHAHAHA!!!
One thing I mostly remember to do when I plan to disassemble the ribbon cables is to turn off the internal power switch first.
I know this is an older thread but does anybody know where to get a new camera. The one that is linked to in the above post is no longer available. Thanks
Sent from my Transformer Prime TF201 using Tapatalk 2
Just 35 minutes ago my phone fell from my hands and onto some cable in the perfect way that it broke the Digitizer. Wonderful. So now I have to go about replacing this. It looks pretty straightforward and I will be doing this but I have a few questions I'd like to see if I can get answered. Perhaps this can be used by others as a helpful FAQ regarding replacing the LCD or Digitizer on an HTC Rezound.
1) I know I will be needing the Digitizer only as the LCD portion is not broken, so can anyone give me a good reason why I should replace both and not just the digitizer?
2) I know there are some adhesives involved in holding it together. Are these re-usable or should they be replaced? If they should be replaced, what kind of adhesives are they and where can they be found?
3) What is a good source for these parts? (Adhesives and digitizer)
4) Is there upgrades here I can do? Like a gorilla glass digitizer or something?
5) I've read a guitar pick is a great tool to separate parts, do you agree?
6) Any Gothca's that I should be concerned about
Here is the procedures I will be following:
1) Remove the back cover, the battery, SIM card and SD Card
2) Remove the 6 T5 torx screws around the sides (from the back)
3) Pry up the back by releasing the plastic clips around all 4 sides (note the volume rocker/power button may fall out)
4) Remove the Vibrator motor
5) Remove the two screws holding the MoBo on and lift up from the USB port side and remove the plastic piece from there.
6) Release the small plastic clips holding the Mobo in and swing it up, release the two ribbon cable connections
7) Heat around all sides front and back to loosen the adhesive, from the back work with a guitar pick to loosen the adhesive, repeat this process from the front.
8) Work around with the guitar pick between the screen and the housing from the front and remove the LCD and digitizer from the housing
9) Heat all the sides of the LCD/digitizer to loosen the Adhesive
10) Work with the guitar pick around the sides to release the digitizer from the LCD screen. It seems there is a piece of black tape on one side, you would have to "butterfly" the two screens and peel the screens apart.
11) Done. Reverse these steps to rebuild it. Do these adhesive parts need the adhesive replaced? Does the tape need to be replaced?
I cannot post links yet, but I felt I should give credit where its due. To obtain these steps I used a Youtube video. To view this video, search youtube for: 'How To Fix HTC Rezound Screen by RepairsUniverse.com'
The advice from the experts is highly anticipated!!
Regards,
Eduard Tieseler
The best reason for replacing both is that you won't have to worry about binding them or getting dust between them if you get them together preassembled. As to the rest, I can't say. I know we have a few people here who have done it.
So I found the adhesive strips that I need. It comes as a bulk sheet where you cut them to fit. I am going with replacing only the digitizer. Replacing the LCD screen also would male the process easier however I fear getting a replacement screen that is in worse shape or more poorly made than the original one my phone came with. I know this one has no flaws.
So I have answered my questions already. I'll post here when I done replacing the digitizer with anything that is of interest in case someone else has questions about this procedure.
Thank you for your input shrike1978. Much appreciated.
Regards,
Eduard Tieseler
Sent from my Infected HTC Rezound using xda app-developers app
etieseler said:
Just 35 minutes ago my phone fell from my hands and onto some cable in the perfect way that it broke the Digitizer. Wonderful. So now I have to go about replacing this. It looks pretty straightforward and I will be doing this but I have a few questions I'd like to see if I can get answered. Perhaps this can be used by others as a helpful FAQ regarding replacing the LCD or Digitizer on an HTC Rezound.
1) I know I will be needing the Digitizer only as the LCD portion is not broken, so can anyone give me a good reason why I should replace both and not just the digitizer?
2) I know there are some adhesives involved in holding it together. Are these re-usable or should they be replaced? If they should be replaced, what kind of adhesives are they and where can they be found?
3) What is a good source for these parts? (Adhesives and digitizer)
4) Is there upgrades here I can do? Like a gorilla glass digitizer or something?
5) I've read a guitar pick is a great tool to separate parts, do you agree?
6) Any Gothca's that I should be concerned about
Here is the procedures I will be following:
1) Remove the back cover, the battery, SIM card and SD Card
2) Remove the 6 T5 torx screws around the sides (from the back)
3) Pry up the back by releasing the plastic clips around all 4 sides (note the volume rocker/power button may fall out)
4) Remove the Vibrator motor
5) Remove the two screws holding the MoBo on and lift up from the USB port side and remove the plastic piece from there.
6) Release the small plastic clips holding the Mobo in and swing it up, release the two ribbon cable connections
7) Heat around all sides front and back to loosen the adhesive, from the back work with a guitar pick to loosen the adhesive, repeat this process from the front.
8) Work around with the guitar pick between the screen and the housing from the front and remove the LCD and digitizer from the housing
9) Heat all the sides of the LCD/digitizer to loosen the Adhesive
10) Work with the guitar pick around the sides to release the digitizer from the LCD screen. It seems there is a piece of black tape on one side, you would have to "butterfly" the two screens and peel the screens apart.
11) Done. Reverse these steps to rebuild it. Do these adhesive parts need the adhesive replaced? Does the tape need to be replaced?
I cannot post links yet, but I felt I should give credit where its due. To obtain these steps I used a Youtube video. To view this video, search youtube for: 'How To Fix HTC Rezound Screen by RepairsUniverse.com'
The advice from the experts is highly anticipated!!
Regards,
Eduard Tieseler
Click to expand...
Click to collapse
Check out my thread: http://forum.xda-developers.com/showthread.php?t=2189789
I did it not long ago, and was fine. However, I opted to go for the digitizer + LCD assembly, as I didn't want to have to worry about separating the digitizer from the LCD and worrying about dust.
To answer your questions:
1) It's eaiser, takes less time, and you don't have to worry about dust with replacing the digitizer + LCD assembly.
2) Replace the adhesive. I tried reusing it... and it has some flex on it. So I got some new adhesive, scraped the old stuff off, put the new one, and used a heatgun to move the screen assembly around to get it to fit right, and then pressed it down as it cooled to secure it better.
3) Ebay
4) Not sure on this one... not that I know of anyway.
5) If you get the parts from eBay, then they sometimes come with tools (Torx, philips, and a plastic separator tool).
I also linked the video that I used in my thread, so you can look at that. It's pretty straightforward and easy to do. Took me about 45 minutes to just over an hour to do everything, as I was taking my time.
Well I did this process two days ago and for the most part it went well, but not without its issues.
First off, I should have heeded the advice of others suggesting to get the LCD + Digitizer pre-assembled. I tried to save some money however now there is a dead spot on my phone and I will have to spend that extra money to buy the kit anyways. So for anyone else thinking they can get away with just the digitizer, unless you have dustless neoprene gloves and a clean room (or possibly nitrogen or canned air) and lots of experience, do not attempt to replace one or the other, just get the pre-assembled kit.
I am going to replace it again with the kit in a few more days.
The only thing that came up that I didn't see anywhere else, was when I was pulling the back cover off. The spot where the camera is located was kind of sticking to the back cover. If I would have pulled to quickly or was too rough I would have easily damaged the camera. So my advice would be to work slowly when pulling the back cover off. If it feels like its resisting, it could be your camera. Wiggle it slightly and don't force it. The camera will loosen itself from the back case, but using too much force you could damage it.
Thanks for the info guys! :good:
etieseler said:
Well I did this process two days ago and for the most part it went well, but not without its issues.
First off, I should have heeded the advice of others suggesting to get the LCD + Digitizer pre-assembled. I tried to save some money however now there is a dead spot on my phone and I will have to spend that extra money to buy the kit anyways. So for anyone else thinking they can get away with just the digitizer, unless you have dustless neoprene gloves and a clean room (or possibly nitrogen or canned air) and lots of experience, do not attempt to replace one or the other, just get the pre-assembled kit.
I am going to replace it again with the kit in a few more days.
The only thing that came up that I didn't see anywhere else, was when I was pulling the back cover off. The spot where the camera is located was kind of sticking to the back cover. If I would have pulled to quickly or was too rough I would have easily damaged the camera. So my advice would be to work slowly when pulling the back cover off. If it feels like its resisting, it could be your camera. Wiggle it slightly and don't force it. The camera will loosen itself from the back case, but using too much force you could damage it.
Thanks for the info guys! :good:
Click to expand...
Click to collapse
I also purchased the full assembly and was able to switch the new parts onto my Rezound. Unfortunately, the earpiece (the part you listen to when NOT on speakerphone) and the proximity sensor did not work with the new set, and I am swapping it for a replacement. However, I've been inside the unit now 5 times, and I suggest in addition to the tools supplied with the sets (t5, small phillips and separator) you also have a small flathead (helps with starting the split the unit apart and also with pulling and reattaching the vibrator motor) and a long tweezers (invaluable when trying to reconnect the ribbon cables.)
Also, reconnect the MIDDLE ribbon cable (which is slightly twisted and longer) first, then reconnect the top, and don't forget to reapply the insulating tape (been there, done that).
Watch the take apart video on Youtube repeatedly until you can do it with your eyes closed, and be careful, the red plastic does break easily, especially on the corners.
Replaced my digitizer with good success, using new adhesive. Upon first re-assembly the digitizer was popping out of the plastic bezel a bit, but everything worked great, touch, display, everything. So I decided to take apart, add some more adhesive strips. Now the digitizer stays flush.
First boot after 2nd re-assembly, got boot with first vibrate, but no screen on. So I pull the battery to attempt again. Now I receive no vibrate response from power button. When plug into charger, orange light comes on for 5 seconds and then off indefinitely. This happens each time after battery pull+wall charger plugin.
I have tried multiple times disassembling, checking both ribbon cables that plugin to motherboard, appear to connect fine. Visually all other aspects of MB appear fine.
Any ideas anyone? Not sure what may have broke. I should have left well-enough alone, but the digitizer was somewhat spongey to touch on right side of screen and I could see white light shine up... TIA
Each time I pull the batt the orange light will come on solid for 5 or so sec, then off for good. One time even started flashing for a bit like it was charging from full depletion (like it does before it lets you power on). Not sure how to diagnose.
Did you make sure to put the yellow protective tape over the ribbon cable connections? When you open it (like a book) and see two ribbon cables. There originally was a small piece of tape over the connection to provide protection from anything being shorted out. Make sure this is back on.
If you no longer have the tape, I think any non-conductive tape would work like plain Scotch tape. Please correct me if I am wrong in that statement.
Sent from my Infected HTC Rezound using xda app-developers app
etieseler said:
Did you make sure to put the yellow protective tape over the ribbon cable connections? When you open it (like a book) and see two ribbon cables. There originally was a small piece of tape over the connection to provide protection from anything being shorted out. Make sure this is back on.
If you no longer have the tape, I think any non-conductive tape would work like plain Scotch tape. Please correct me if I am wrong in that statement.
Sent from my Infected HTC Rezound using xda app-developers app
Click to expand...
Click to collapse
I did not put those pieces of tape back on. In the YouTube video by "injured gadgets," I don't believe they re-covered up those ribbon cable plugins, so I also did not during re-assembly. Should I try that? Or, I assume, my board somewhere has gone bad? (Phone did work just fine after re-assemble, until I decided to take apart again)
And after doing this a handful of times, I figured out that the "earpiece" doesn't come with the digitizer/LCD/housing. It has to be pulled from the old phone and moved to the new one. Once I did that, everything was fine.
hgoldner said:
And after doing this a handful of times, I figured out that the "earpiece" doesn't come with the digitizer/LCD/housing. It has to be pulled from the old phone and moved to the new one. Once I did that, everything was fine.
Click to expand...
Click to collapse
hgoldner, when you had forgotten to re-apply the insulating tape over the ribbon cables, did that result in a toasted motherboard? I'm trying to find out if that's what happened to mine? Thx
red3razor said:
hgoldner, when you had forgotten to re-apply the insulating tape over the ribbon cables, did that result in a toasted motherboard? I'm trying to find out if that's what happened to mine? Thx
Click to expand...
Click to collapse
I would go ahead and try putting it back on. There was an earlier post where someone mentioned it was important to put it back on, perhaps he can comment on what can happen if its not on (He said he learned from experience). Perhaps you can PM him.
To be honest, I originally only put the tape back on one connection, but after the second time replacing both the LCD screen and the digitizer, I found the second piece of tape and now both are back on.
What can it hurt to see if that will fix it? Its fairly easy to get to on these phones.
Ed
Yes I did try put back on, no worky still. I assume motherboard issues now. So now I ask if anyone that has also failed to put tape insulation back on, has also resulted in motherboard fail?
red3razor said:
Yes I did try put back on, no worky still. I assume motherboard issues now. So now I ask if anyone that has also failed to put tape insulation back on, has also resulted in motherboard fail?
Click to expand...
Click to collapse
I ran it for about a week or so without the insulating tape. I assume you just mean the translucent, amber tape that goes over the jaw connectors of the ribbon cables on the motherboard? Not putting that on shouldn't have damaged your board... it's really just there to keep the jaw connectors from opening from vibrations.
carngeX said:
I ran it for about a week or so without the insulating tape. I assume you just mean the translucent, amber tape that goes over the jaw connectors of the ribbon cables on the motherboard? Not putting that on shouldn't have damaged your board... it's really just there to keep the jaw connectors from opening from vibrations.
Click to expand...
Click to collapse
I left it off on one connection for about a week also with no issues. However I did notice roughly a 16th of an inch of copper exposed on the ribbon. I can envision potential issues from that. I'm not sure about your phone, but the jaw connectors on mine would never open on their own. Far too much resistance to open from any vibration or movement. The vibrator motor connection had a better chance of disconnecting on its own than the ribbon cables. I'm sure that tape provides more than just locking the jaw connectors closed. I could be wrong though.
red3razor said:
hgoldner, when you had forgotten to re-apply the insulating tape over the ribbon cables, did that result in a toasted motherboard? I'm trying to find out if that's what happened to mine? Thx
Click to expand...
Click to collapse
No, I remembered and put it on before I powered up.
Dumped down the innertubes from my Asus Transformer TF300T
Just replaced my digitizer two days ago and I must add the difference is like night and day. I noted in a post that I had tripped and fell on it with my knee...lol ..nope.. I threw the damn thing and it hit the wall. Yahhh.. I know stupid lol... Something really pi$$ed me off tho and I kinda lost it.. .poooof....... Anyway, I had about 30 cracks in my digitizer and amazingly it still worked. Replaced it two days ago and it works great.
That factory adhesive is some SERIOUS stuff. I have performed many electronics repairs over the years and this...well...removing the digitizer and applying the new strips in exactly the right size was a royal pain in the a**! You REALLY gotta get that digitizer glass HOT if you want to be able to loosen it. Light heating WONT do squat to it. And the new strips arent even half as strong as the factory stuff. You really need patience and precision here.
Yes, dust ISVan issue where I live. Canned air came VERY useful. Also its good to have isopropyl alcohol and soft paper towels so you can clean any smudges you make on the LCD before reapplying the digitizer glass. Basically it's best to blow air over it quickly as you press the digi down to the adhesive. That makes sure every bit of contaminant is out.
About the ribbon cables, no I didn't reapply the amber tape to the jawbone connectors. Much of their adhesiveness was lost when I pulled them off. And as long as the ribbon cables are seated in properly and the jawbone connectors are securely locked down, they wont come disconnected. The tape is only there as an additional measure to secure the jawbone connectors from unlocking. Unless you drop your phone on concrete a lot, those cables arent coming loose....even then, dropping it wouldnt knock those loose.. Its more secure than you think. As far as the phone NOT working, the orange tape would have NO effect on that. Maybe one of your cables were partially disconnected and shorted out something on the mainboard. Either that, or it is static sensitive. Its possible if anything is CMOS.
ONLY issue I have since the repair is the top of the digitizer keeps pushing up because of the digitizer ribbon cable and where you have to bend and fold it in that groove to guide it behind the LCD . The ribbon isnt pinching down well and acts as a spring on the digitizer glass....adhesive not doing anything for that.
oh, did you all remove and reapply the clear (4 button tabs) at the bottom to the new glass? got mine in (the lights are pink now ...weeee ) Had to use some Gorilla super glue to restick them. That adhesive at the bottom was super strong and somehow they lost their stickiness when I pulled them off.
Digitizer after I finally got it unstuck from the LCD... wheewww damn. Lots of cracks. Thats what happens when the phone face eats the wall.....
So, my 4 soft keys on the bottom have yet out. Would fixing the digitzer get them back to working? My screens just got cracked like 2 days ago too, and I just want to make sure before i do all this and then find out i gotta take it all apart again. Thanks in Advance!
MY XZU Cable fault ;-c
I try to fix
But, the cable is attached to the motherboard
I do not know what I soldered or heat ;-c
Help the person to fix cables
Attachments Photo!!!
HEXAHN said:
MY XZU Cable fault ;-c
I try to fix
But, the cable is attached to the motherboard
I do not know what I soldered or heat ;-c
Help the person to fix cables
Attachments Photo!!!
Click to expand...
Click to collapse
You can't fix this by yourself, unfortunately. It's glued on with some special adhesive, the contacts are to tiny to solder. The glue you buy on ebay (i assume), next problem is getting the flex cable on the right place and keep it their while glueing.....
You can look for a motherboard replacement, only last time i checked it's almost as expensive as a new phone.
Some manufacturers use small clamps for the flex cable, i assume glue is the trade off for this tiny device...
I've been to this hassle myself, i ended up on buying a new ultra
Has someone have any other suggestions? Have detached the main flex from the board. Had the main flex broken, wanted to fix, but know it's just disassembled. Had display problems before.
Can someone have some ideas? like those clamps you mentioned.
Bro your beating a dead horse, just buy a used one online
hot bar soldering attachment, anisotropic adhesive film/tape( apparently you can buy this for whole sale only. lucky for me the company I work with has spare trimmings of this), microscope or powerful magnifying glass and a lot of patience.
bump, i am in this boat, there must be a dozen lines on the cable, i cant imagine soldering it without shorting it out....
Why do they sell those toys that cannot be repaired by the way?
I'm in the same boat an all y'all being no help are no help so bump outta here already cuz everyone else in this boat looking for the answer doesn't wanna WASTE THEIR TIME on your helpless posts.
To recap we have the solder method which sounds like rubbish as flex cables melt.
Then there's that kind of adhesive glue and/or tape. Clamping is the reason phone companies profits dwindled until they switched to this new clampless method. I'm not gonna buy in bulk cuz I'm not about to start up a cell phone chop shop so maybe get a magnifying headset, some Walmart super glue that says mess free, and use a needle to dab the glue on in the right points but don't cover any contacts!
Did anyone ever managed to get this done?
I also recently experienced, looking at google solution does not get the information.
Try YouTube? I'm sure it applies to other z models
jigzerx said:
Did anyone ever managed to get this done?
Click to expand...
Click to collapse
I just did this. I didnt use that ADH* glue some people are talking about. I simply inspected how the old one is soldered on. Then removed the old one. There will be slight residue of the glue people are mentioning. I just simply took the solder tip OFF my soldering iron. then used a magnify glass to align the new ribbon. I also used clear tape to hold half of the ribbon down. Meaning i did 1 side at a time. So i taped from the middle to the far left to hold the ribbon down. I then used the blunt end of my soldering iron with the tip removed to press down with some force. Stayed in one location and counted to 20 the slid a little bit to the left. repeated this till the right 50% of the ribbon seemed glued down. I then applied clear tape over this portion and moved over to the previously taped left side. Repeating what I did on the right. after about 10 minutes of work. attached battery, press on button, phone came on. Then tested volume up and down and all worked.
lesterine said:
I just did this. I didnt use that ADH* glue some people are talking about. I simply inspected how the old one is soldered on. Then removed the old one. There will be slight residue of the glue people are mentioning. I just simply took the solder tip OFF my soldering iron. then used a magnify glass to align the new ribbon. I also used clear tape to hold half of the ribbon down. Meaning i did 1 side at a time. So i taped from the middle to the far left to hold the ribbon down. I then used the blunt end of my soldering iron with the tip removed to press down with some force. Stayed in one location and counted to 20 the slid a little bit to the left. repeated this till the right 50% of the ribbon seemed glued down. I then applied clear tape over this portion and moved over to the previously taped left side. Repeating what I did on the right. after about 10 minutes of work. attached battery, press on button, phone came on. Then tested volume up and down and all worked.
Click to expand...
Click to collapse
Can u explain me how u attached the flex cable back to its place. I didnt full understud this explanation. Have the same problem hoping u can help me.
using the soldering iron t shape tip, step 1 using the scraper to scrap away the glue then install the silicone strip to heat the flex cable on the board. hope this help.
Have same problem too! When I transferred the board with the power/volume button flex cable to a new housing, I accidentally lifted part of the flex cable causing my XZU C6833 not to boot up, no vibration and no screen image.
And can't seem to find any tutorial on how to properly attach the said cable onto the main board.
Will try lesterine's solution.