Related
I was trying to upgrade to radio v1.43 in the hope that battery life was improved over 1.41 however when it got to 8% it stopped and gave me an error i can't remember After atempting to recover, it got off the three colour screen now the 3100 stalls on the blackshadow version4 screen (bootloader screen?) and goes no further. I tried reflashing but got a 260 and using mtty, only getting 2 com port options, didn't offer any help.
I'm really sorry to have not been able to sort this with reading through the relevant post but I haven't found a solution. What else can I try?
Hi,
Could you pls advise what is your device made, model, SPL version ... etc.
Also did you try to do Hard reset?
I'm using now black MAJIK (and few days ago black shadow) with radio 1.43 with no problem.
its the SPV m3100 When I decided to go Black shadow I read up on mr vanx and made sure I had all the things I needed. If I remember right, when I came to upgrade to Majik the auto detect found the second option down
SPL-1.04/1.10 - 1.09 Bootloader. I've realized since I had a spaz and ran the RUU from the archive this time. From what I've since read thats not too cleaver.
I have tried a hard reset and took the battery out instead of pressing space.
I dont know if this information on the starter screen is of use
M 05
S 04
B 05 D 3lak
I'm not sure, but hard reset doesnt mean you take the batery out.
Please check that link:
http://wiki.xda-developers.com/index.php?pagename=Hermes_For_Beginners#hardreset
I was in your position (hanged on booting) few days ago, and when i did hard reset, it changes every thing to basic normal condition.
i meant when i did a hard reset when it asked me to press space to reboot I took the battery out. I tried again this time pressing space to reboot but I still get stuck on the loading screen. I can't connect by USB to the PC I'm guessing the drivers on the phone haven't loaded and I'm stuck as to what to do.
Does anyone have any ideas?
try look at it http://forum.xda-developers.com/showthread.php?t=286755
ok I've tried everything I can think of to connect the 3100 to the computer so I can reflash it but mtty gives only com 1 and com2 but no USB and neither those two work, active sync wont connect so I disabled it as suggested and running the radio ruu and wrapper wont querry the device. I am now at a loss as to what to do next someone must know what I should do. Please?
what is your SPL?
try this http://wiki.xda-developers.com/index.php?pagename=HTC_Hermes
sl is 1.09 i'd updated it on the previously successful black shadow flash
msn [email protected]
icq 150277111
AIM TazmanFH9
Yahoo bigfathairyboggart
I have tried changing KITL trasport but I am unable to select or chose either option. I have also tried the rversion command in the tri colour screen but nothing happens. I hope I'm missing something nice and simple but I get the feeling I'm not going to be that lucky. Please help
tcSPVm3100 said:
sl is 1.09 i'd updated it on the previously successful black shadow flash
Click to expand...
Click to collapse
I suggest you check again, press and hold the side OK button and the power button...then put the stylus into the hole in the bottom of the unit.
yeah I've done that it's "SPL-1.09"
I had this exact problem yesterday, with the same bootloader too. The phone would not pass the splash and IT refused to upgrade. I ended up downgrading to a shipped wm5 rom (in my case the cingular 1.30.502.1_1.11.00.00) which to my surprise actually worked as no rom radio or spl upgrade moved at al on my phone. Then upgraded back to black majik. I hope this helps.
Thanks. I downloaded the trial of wm5 from the windows website and it asked me to install .NET framework version 1 so I got that but it turns out to be 2.0 not 1.1 It would say it had repaired but it would say this with or without the phone connected.
tcSPVm3100 said:
Thanks. I downloaded the trial of wm5 from the windows website and it asked me to install .NET framework version 1 so I got that but it turns out to be 2.0 not 1.1 It would say it had repaired but it would say this with or without the phone connected.
Click to expand...
Click to collapse
Just download a WM5 ROM from the wiki page!
ok tried this too no luck.
Trying to use the one from orange (linked to through wikki) I get an 294 invalid vendor error however active sync cannot connect yet of course so is this to be expected?
I have however gotten a connection with mtty which is a step forward dunno what to do with it yet though except trying the password 0000000000000000 command but it not disabling the password. This then lead me to read for a further hour how to change it and I've got to be honest; it beat me. I have No idea what the hell its talking about. My head hurt with so much reading.
I get a no gsm pop up v briefly on loader. I so want my phone back
I have since tried CID unlocker just so i get something installed onto this brick but I either get a connection error or it telling me it can't install for some other reason. I can not set the password in mtty to 0000000000000000 so how do I do that and is this the first step to getting things sorted? "just running a rom install" is not happening I can get a USB connection in mtty and that is it. Is the fact i'm running SPL 1.09 a problem? I'm getting precious little help guys If i'm posting in the wrong place or something please let me know. I need thing thing back now. Hours are drifting by with me trying to get some head knowledge but I still need some guidance please
tcSPVm3100 said:
I have since tried CID unlocker just so i get something installed onto this brick but I either get a connection error or it telling me it can't install for some other reason. I can not set the password in mtty to 0000000000000000 so how do I do that and is this the first step to getting things sorted? "just running a rom install" is not happening I can get a USB connection in mtty and that is it. Is the fact i'm running SPL 1.09 a problem? I'm getting precious little help guys If i'm posting in the wrong place or something please let me know. I need thing thing back now. Hours are drifting by with me trying to get some head knowledge but I still need some guidance please
Click to expand...
Click to collapse
can u flashing HARD V7?,i think better u have IPL 1.04 SPL 2.10olipro first ,then try to flashing radio?
and did u try SD card.
In bootloader can anyone here connect with active sync? I can't so updating rom and radio flashes in the usual way isn't possible. Trying the hard spl again it tells me to make sure active sync is connected and as it isn't it throws back a 262 update error. 0% on the hermes and that's currently as far as I can get. I have no means with which to access the memory card.
The reason you get an invalid vendor ID is because your CID doesnt match....download a ROM which is for your device (an orange one?)...then try.
You need to read the wiki alot more before trying anything else since you are not aware of the vendor ID error...nor the fact you MUST use HardSPL.
I linked to the orange ROM from wikki and tried installing it. it was while installing THIS ROM SPV_M3100_ROMUpdate_0407.exe I got invalid vendor error.
Installing a recent DL on HARD spl v7 I get a 240 open file error that's one I haven't had before.
With all other attempts they all say they want an active sync connection.
I can not connect to the phone through active sync
so all attempts by me to flash anything to the phone using an RUU fails.
Hi
I was given an Orange SPV M600 running WM5.0 I foolishly thought I would be able to unlock it to work with my T-Mobile sim (the only network I can get coverage at home) I ran an unlock tool from en.pdamobiz.com
http://files.pdamobiz.com/c/PDAMobiz.com_ProphetAKU2_unlockCID.rar
I managed to get to through to the completion of the Downgrade.bat process. I was then asked to sofdt boot the M600 but it now cannot be found by Activesync. I was unable to successfully run Unlockcid.bat and now it just boots to either the 'Orange' screen (displaying IPL 2.10.0001, SPL 2.10.0001, GSM 02.07.20 & OS 1.0.13.21 - the new OS I believe) or the 3 colour screen (displaying IPL 2.10.0001, SPL 2.10.0001) if I hold down the camera button.
Windows 5.0 has gone or is unreachable but I am assuming it can't be completely dead as I get a noise when connecting/disconnecting the USB lead....
Is this false hope? Have i killed it after 2 days of ownership??? Should I have attempted this process with very little tech knowledge - me thinks YES!
I would be eternally greatful to anyone who can help me out of this black hole..... I just need pointing in the direection of what stage the M600 is at and how to get it running on my T-Mobile sim.....
Thanks in advance
hi there, try going into the bootloader screen, when you connect the usb cable it should show on the bottom off your screen. then try uploading the orange rom you can find on the wiki page. if this works then try using the loki unlocker which you should also be able to find on the wiki page. i used the loki tool and it unlocked first time. hope this helps. let me know how you go.
The GOOD news is No you haven't killed it. It seems you have wiped the operating system from it. I would sugest searching for RUU-Prophet-G4-AKU2.2-2.20-2.47.21-Jester-r1.exe down load it and then get your phone to the multi colour screen before running the download. This should then update your phone
when I tried to unlock my phone, I couldn't get it to unloack at all till I put a orange pay as you go sim in the phone and registered the sim with orange then it unlocked first time.
Killed prophet reborn!!
Fingers666 said:
hi there, try going into the bootloader screen, when you connect the usb cable it should show on the bottom off your screen. then try uploading the orange rom you can find on the wiki page. if this works then try using the loki unlocker which you should also be able to find on the wiki page. i used the loki tool and it unlocked first time. hope this helps. let me know how you go.
Click to expand...
Click to collapse
Spot on. Thanks so much for the advice. Fingers666 & jazpa !! I'm back on track. M6000 is now communicating again. WM5 is resident. Just need to unlock the sim and I'm away. [email protected] tried loki 3.0 amd 3.0a with both Activesync 4.2 and 4.5 respectively without any luck so I've just spent £5 a http://www.unlocking.org.uk/ as they say they can unlock a G4 ver. We shall see!! Great help though and THANKS again to both of you
Please Help Meee!!
Hello i was wondering if anybody could help me.
I want to unlock my orange SPV M600 for free.
If there are any safe and free websites that anybody knows of could u please tell me.
Thank Youu!!
James Thomas
Download Lokiwz, it is quite easy to locate. Inside the folder you will find 1 or 2 cab files, copy these to your storage card and run them on your M600. Now run Lokiwiz from your PC, after around 12 minutes, it will display your sim unlock code. Switch off your M600 and insert the sim you want to use, at the prompt, enter your code lokiwiz generated. For around 2 minutes the phone will seem to have no signal, then it will connect.
Worked first time for me, my M600 was locked to Orange, now it works great with O2.
wonderful works great with G4
thanks
mike
So forgive me, as I'm mostly new. I have been searching for hour for a thread, not wanting to duplicate and I cannot find this issue.
Windows XP Pro Computer
Running WM5 on the BRAND NEW phone.
Just downloaded activesync 4.5
I bought an att8525 and want to upgrade it to wm6. I found the thread with the official rom's. I figured I'd do the official before I got tricky. My problem is this, when I run the program and the phone is connected, the phone kicks off into the tricolored screen (I believe is the bootloader?) I try to run the upgrade and before the upgrade begins one screen says be sure you have an activesync connection. Well, I can't get an activesync with the bootloader screen on. So I tried running the program with the phone in bootloader AND I tried getting the phone back to the OS before continuing the installation. Neither worked.
So both come back with an error trying to connect to the phone spitting back crap about be sure the phone is still connected".
In the bootloader?? screen it says 2 things.
herm100
ipl-1.03
herm100
spl-1.11
I have had no problems with this phone before... and I very much would like windows mobile 6, and I know it works, I've seen it, I just don't know whats going on. Please, any help would be appreciated.
____________________
~Dan Allen.
A+. Net+. MCP. CCNA.
I feel your pain and had the same problems.
Bag the conventional upgrade and use the memory card method. Refer to the instructions in the wiki. It works quite well.
I had the same problem. I used this and it worked:
http://forum.xda-developers.com/showthread.php?t=317952
Where do I put the .nbh??? first time to this. Thanks.
follow the instructions here...
http://wiki.xda-developers.com/index.php?pagename=Hermes_SDCardFlashing
GReddySetGO said:
I had the same problem. I used this and it worked:
http://forum.xda-developers.com/showthread.php?t=317952
Click to expand...
Click to collapse
I just tried this method and got another wrong vendor error. Thanks though
~~Dan
Put HardSPL v 7 first (or SUPERCID will also do it)
wpbear said:
Put HardSPL v 7 first (or SUPERCID will also do it)
Click to expand...
Click to collapse
Awesome. I tried some things to SuperCID, but nothing worked as well as pof's any bootloader version 3 supercid program. Amazing.
Then loaded up the ROM, works great, thanks all.
Hey guys...sorry if this has been covered. I tried searching the forums and can't seem to find anything on it.
All of the roms seem to be plug it in, install it and BLAM, you're ready to go.
My issue is that I get a communication error everytime I try to install any roms or the HardSPL. The exact error given is "The ROM Update Utility has encountered communication errors during the update process. The program will guide you step-by-step to recover from the error so you can continue with the update."
While performing the updates, I hear the sound as if my USB disconnects, then it reconnects after it restarts into the multi-colored screen. It shows "Security disabled" at the top of the screen. It proceeds to the loading bar and just sits at 0% until it comes up with the disconnect screen.
I'm using the HTC Touch Pro running WM6.1 on the Sprint network.
Again, sorry if this has already been discussed, I just couldn't find anything on it.
rceubanks said:
Hey guys...sorry if this has been covered. I tried searching the forums and can't seem to find anything on it.
All of the roms seem to be plug it in, install it and BLAM, you're ready to go.
My issue is that I get a communication error everytime I try to install any roms or the HardSPL. The exact error given is "The ROM Update Utility has encountered communication errors during the update process. The program will guide you step-by-step to recover from the error so you can continue with the update."
While performing the updates, I hear the sound as if my USB disconnects, then it reconnects after it restarts into the multi-colored screen. It shows "Security disabled" at the top of the screen. It proceeds to the loading bar and just sits at 0% until it comes up with the disconnect screen.
I'm using the HTC Touch Pro running WM6.1 on the Sprint network.
Again, sorry if this has already been discussed, I just couldn't find anything on it.
Click to expand...
Click to collapse
Your phone's cdma. This is a gsm forum. I'm assuming that you're trying to brick your phone with the gsm hard spl and not trying to flash the proper hard spl. Stop doing that, your phone is getting pissed at you. Go to ppcgeeks or the cdma (Herman, not Raphael) forum here.
haha leave it to me to find the wrong way to do something. I appreciate your heads up Ted!
rceubanks said:
Hey guys...sorry if this has been covered. I tried searching the forums and can't seem to find anything on it.
All of the roms seem to be plug it in, install it and BLAM, you're ready to go.
My issue is that I get a communication error everytime I try to install any roms or the HardSPL. The exact error given is "The ROM Update Utility has encountered communication errors during the update process. The program will guide you step-by-step to recover from the error so you can continue with the update."
While performing the updates, I hear the sound as if my USB disconnects, then it reconnects after it restarts into the multi-colored screen. It shows "Security disabled" at the top of the screen. It proceeds to the loading bar and just sits at 0% until it comes up with the disconnect screen.
I'm using the HTC Touch Pro running WM6.1 on the Sprint network.
Again, sorry if this has already been discussed, I just couldn't find anything on it.
Click to expand...
Click to collapse
Try here: CDMA Herman
same issue on GSM phone
Hi I have the same problem on a GSM phone.
I get the updating bar on my phone- it stays stuck at 0%.
then a communications error
Thanks in Advance
What is the problem with the RUU update?
I have searched for a solution to the RUU update/upgrade problem; none so far. Apparently, it is a major issue. I am interested in upgrading my Windows CE on my Xperia 6.1 to 6.5. I must have tried over a dozen times. The update process stops at 0% and Error [262] is reported. What can we do to resolve this? Is it compatibility or scalability issue? is it a problem with the software? The fact that it is working for some . . . and not for others is a source of concern about the stability of the software and this has potential implications; or it may well have to do with the hardware limitations of the PDA. Any ideas of a workaround?
You might try the Experia forum. You also might want to try Experia Roms.
I used to experience this issue as well. I simply go into communications and hit the USB to PC connection. Then remove the advanced functionality check. This has resolved many of the communication errors when playing with ROMS. This has been true with both GSM and CDMA devices.
I can confirm the issue. I have a 1st day release Fuze and flashed HardSPL no problem and have been making my roms ever since. But my cousin just got his new AT&T Fuze through his company and it refuses to HardSPL.
I went through several versions of the HardSPL and tried installing new drivers for the phone while in bootmode... all with no luck.
When connected through Activesync or Mobile Center, running the HardSPL brings up a confirmation windows on the phone, allowing reboots the device. It gets stuck at the black screen and times out. I've tried manually putting the phone in bootmode and trying it, but never gets past 0%.
I wonder if newer model TouchPro's are coming out with a revised bootloader?
Dunno if i can link to another forum. If not, appolgize and Admins remove the link than please.
For the 262 error, look here:
http://www.4winmobile.com/forums/windows-mobile-faq/13329-ruu-errors.html
player911 said:
I can confirm the issue. I have a 1st day release Fuze and flashed HardSPL no problem and have been making my roms ever since. But my cousin just got his new AT&T Fuze through his company and it refuses to HardSPL.
I went through several versions of the HardSPL and tried installing new drivers for the phone while in bootmode... all with no luck.
When connected through Activesync or Mobile Center, running the HardSPL brings up a confirmation windows on the phone, allowing reboots the device. It gets stuck at the black screen and times out. I've tried manually putting the phone in bootmode and trying it, but never gets past 0%.
I wonder if newer model TouchPro's are coming out with a revised bootloader?
Click to expand...
Click to collapse
Yes they are coming with a new bootloader. I just got my phone replaced from ATT and the new one came with 1.95 version while originals were 1.90. There is no HARD-SPL out for 1.95.
The way to do it now is to flash an old original AT&T rom with the 1.90 bootloader (since it's original, it won't require HardSPL). Then go ahead and everything should work as described in this forum/wiki.
Interseting. Sounds like a winner. Next time he comes around I'll try this.
Any idea where I can get a AT&T older rom that has the 1.90 HardSLP on it? I am having the same issue with the Error 262 update error.
Thanks
smicale said:
Any idea where I can get a AT&T older rom that has the 1.90 HardSLP on it? I am having the same issue with the Error 262 update error.
Thanks
Click to expand...
Click to collapse
You should probably go to your ATT store and tell them you'd like to get the official Hard SPL update.
I am really struggling with this. Do I have to the FLASH HardSPL or can I just go straight to the flashing my preferred ROM. I can not get get the FLASH HardSPL to work because of this Error 262. Please someone tell me where I am going wrong with this!!!! I am bout to pull my last hair out!
smicale said:
I am really struggling with this. Do I have to the FLASH HardSPL or can I just go straight to the flashing my preferred ROM. I can not get get the FLASH HardSPL to work because of this Error 262. Please someone tell me where I am going wrong with this!!!! I am bout to pull my last hair out!
Click to expand...
Click to collapse
If u want to use not the official rom made for ur provider and phone, hardspl is the only way. Any custom rom needs hardspl. Otherwise ur phone will not accept the rom.
But look here http://forum.xda-developers.com/showthread.php?t=410150
and flash the stock 1.90 SPL first, then u are ready for hardspl.
Description how to do stock spl is in this thread. Its normally meant for going back to stock for repair, but it should also solve ur issue.
NOT SHURE BECAUSE IN THE CDMA SECTION, IS UR PHONE CDMA OR GSM. MY SOLUTIUON IS FOR GSM !!!!!!
U SHOULD CHANGE THE POSTING SECTION IF ITS GSM !!!!!
Try doing the HardSPL in a Windows XP machine (needs .NET Framework 2.0 and ActiveSync). Goodluck.
i had the same problem as you and i maybe have a solution for you
go to your usb settings and look if you have a check box saying something about advanced networking. if it is indeed checked uncheck it and your problem will be gone hopefully
i did it on my telus touch pro and i am now able to upgrade my phone to winmo 6.5
Hello Everybody,
My mobile at&t 8525 alias HTC 8525 is stuck in windows operator logo.It would not boot further. It happened while I tried to upgrade it from Windows 5.0 to Windows 6.0.First I got a tri-colour screen,but in a hurry I tried to backgrade to windows 5.0 again.
Other problem the mobile cannot be synced. I have installed Microsoft Active sync 4.5. Even then it could not be synced.
I tried to read all the posts ,but could not understand anything.
So please help me in getting my mobile repaired
Don't worie.
I had somewhat the same issue with a bad ROM flash.
Just disconnect the USB and boot to the bootloader screen (the tricolour screen) and you should be able to reflash the phone again.
Problem in syncing the mobile
I am not able to sync the mobile to the laptop.I have installed Microsoft Active sync 4.5. Even then it is not syncing.So how could I run the hermes upgrade if the mobile is not helping.
Please help
In Activesync on PC - Untick "Allow USB Connections".
Put the Hermes into bootloader (tri-colour screen) and connect by usb. Run the RUU_Wrapper.exe file you want. Follow onscreen instructions.
You need to have installed Hard SPL V7 for this to work...
did not work
Hello Boss
I tried to follow the procedure you suggested me. but it did not work. I tried with Hard SPl 7.0.
Please give me some suggestion
you dont need an active sync connection to flash it. Enter bootloader(tri colour screen) as you were told in the previous posts and Just click on the boxes that you do have a connection(even though you dont) and then flash the rom.
@ultramag69 i hve never had to untick allow usb connections and i have cocked up loads of rom flashes, saying that i have never had a problem flashing in vista either so maybe i am lucky
If you still cant flash doing it this way, then maybe you should try flashing from sd card instead, just make sure the battery is fully charged. Full instructions of how to do this are found in the hermes wiki, which i advise you to read anyway.
Oh and good luck anyway, you should be able to recover the phone from this ,so i wouldnt fret too much
Guess he isnt hardspl'ed... then his batt is death... must to flash a shipped rom.
correct me if im wrong.
Problem with upgrade At&T 8525 mobile
Hi!
I'm having problems with my Cingular 8525, after I made the upgrade to WM6.1 (FARIA-R32-XDA2_WM6.1.rar) for WM 6.5 (FCWs_stock_like_6.5_v3.rar), and slowed my device does not work anymore. He died.
I need help please. How resurrect it?
Excuse my English.
english is not the problem here cause we need more info... device info SPL IPL hardSPL? you go from 6.5 to 6.1?
Do you try to flash first the Stripped?
Does your batt has charge enough to boot?
There are many many things to say so... start to tell us all your history!
Hi
I tried to Hard spl with Hard Splv7. But I got a error. I even tried the Sd Card method.Its says loading and I get the tricolour mode. If I press the Power button its not showing the status of upgradation.
Where can I get a shipped rom. Actually my Spl is 1.11.
Hi
I tried to Hard spl with Hard Splv7. But I got a error. I even tried the Sd Card method.Its says loading and I get the tricolour mode. If I press the Power button its not showing the status of upgradation.
Where can I get a shipped rom. Actually my Spl is 1.11.
check the wiki pages for your device in the upper bar of this web forums
there are many official roms.
I also am currently using an 8525 (Herm100). It was received from an Ebay deal with WM5. I flashed it with the ATT OEM WM6pro (aka shipped wm6). Once it hit the three color boot screen, it sat on that for a couple of minutes then started cooking. Once it showed a progress bar, it took about 3 minutes to cook the WM6 over the WM5. It also showed a popup that stated going back to WM5 was not an option.
I would suggest running the installer again and going down to 7-11 for a refreshment. You may not have let it percolate long enough to set itself up for the actual ROM overwriting.
gorkalraghavendra said:
Hello Everybody,
My mobile at&t 8525 alias HTC 8525 is stuck in windows operator logo.It would not boot further. It happened while I tried to upgrade it from Windows 5.0 to Windows 6.0.First I got a tri-colour screen,but in a hurry I tried to backgrade to windows 5.0 again.
Other problem the mobile cannot be synced. I have installed Microsoft Active sync 4.5. Even then it could not be synced.
I tried to read all the posts ,but could not understand anything.
So please help me in getting my mobile repaired
Click to expand...
Click to collapse