Hey guys...sorry if this has been covered. I tried searching the forums and can't seem to find anything on it.
All of the roms seem to be plug it in, install it and BLAM, you're ready to go.
My issue is that I get a communication error everytime I try to install any roms or the HardSPL. The exact error given is "The ROM Update Utility has encountered communication errors during the update process. The program will guide you step-by-step to recover from the error so you can continue with the update."
While performing the updates, I hear the sound as if my USB disconnects, then it reconnects after it restarts into the multi-colored screen. It shows "Security disabled" at the top of the screen. It proceeds to the loading bar and just sits at 0% until it comes up with the disconnect screen.
I'm using the HTC Touch Pro running WM6.1 on the Sprint network.
Again, sorry if this has already been discussed, I just couldn't find anything on it.
rceubanks said:
Hey guys...sorry if this has been covered. I tried searching the forums and can't seem to find anything on it.
All of the roms seem to be plug it in, install it and BLAM, you're ready to go.
My issue is that I get a communication error everytime I try to install any roms or the HardSPL. The exact error given is "The ROM Update Utility has encountered communication errors during the update process. The program will guide you step-by-step to recover from the error so you can continue with the update."
While performing the updates, I hear the sound as if my USB disconnects, then it reconnects after it restarts into the multi-colored screen. It shows "Security disabled" at the top of the screen. It proceeds to the loading bar and just sits at 0% until it comes up with the disconnect screen.
I'm using the HTC Touch Pro running WM6.1 on the Sprint network.
Again, sorry if this has already been discussed, I just couldn't find anything on it.
Click to expand...
Click to collapse
Your phone's cdma. This is a gsm forum. I'm assuming that you're trying to brick your phone with the gsm hard spl and not trying to flash the proper hard spl. Stop doing that, your phone is getting pissed at you. Go to ppcgeeks or the cdma (Herman, not Raphael) forum here.
haha leave it to me to find the wrong way to do something. I appreciate your heads up Ted!
rceubanks said:
Hey guys...sorry if this has been covered. I tried searching the forums and can't seem to find anything on it.
All of the roms seem to be plug it in, install it and BLAM, you're ready to go.
My issue is that I get a communication error everytime I try to install any roms or the HardSPL. The exact error given is "The ROM Update Utility has encountered communication errors during the update process. The program will guide you step-by-step to recover from the error so you can continue with the update."
While performing the updates, I hear the sound as if my USB disconnects, then it reconnects after it restarts into the multi-colored screen. It shows "Security disabled" at the top of the screen. It proceeds to the loading bar and just sits at 0% until it comes up with the disconnect screen.
I'm using the HTC Touch Pro running WM6.1 on the Sprint network.
Again, sorry if this has already been discussed, I just couldn't find anything on it.
Click to expand...
Click to collapse
Try here: CDMA Herman
same issue on GSM phone
Hi I have the same problem on a GSM phone.
I get the updating bar on my phone- it stays stuck at 0%.
then a communications error
Thanks in Advance
What is the problem with the RUU update?
I have searched for a solution to the RUU update/upgrade problem; none so far. Apparently, it is a major issue. I am interested in upgrading my Windows CE on my Xperia 6.1 to 6.5. I must have tried over a dozen times. The update process stops at 0% and Error [262] is reported. What can we do to resolve this? Is it compatibility or scalability issue? is it a problem with the software? The fact that it is working for some . . . and not for others is a source of concern about the stability of the software and this has potential implications; or it may well have to do with the hardware limitations of the PDA. Any ideas of a workaround?
You might try the Experia forum. You also might want to try Experia Roms.
I used to experience this issue as well. I simply go into communications and hit the USB to PC connection. Then remove the advanced functionality check. This has resolved many of the communication errors when playing with ROMS. This has been true with both GSM and CDMA devices.
I can confirm the issue. I have a 1st day release Fuze and flashed HardSPL no problem and have been making my roms ever since. But my cousin just got his new AT&T Fuze through his company and it refuses to HardSPL.
I went through several versions of the HardSPL and tried installing new drivers for the phone while in bootmode... all with no luck.
When connected through Activesync or Mobile Center, running the HardSPL brings up a confirmation windows on the phone, allowing reboots the device. It gets stuck at the black screen and times out. I've tried manually putting the phone in bootmode and trying it, but never gets past 0%.
I wonder if newer model TouchPro's are coming out with a revised bootloader?
Dunno if i can link to another forum. If not, appolgize and Admins remove the link than please.
For the 262 error, look here:
http://www.4winmobile.com/forums/windows-mobile-faq/13329-ruu-errors.html
player911 said:
I can confirm the issue. I have a 1st day release Fuze and flashed HardSPL no problem and have been making my roms ever since. But my cousin just got his new AT&T Fuze through his company and it refuses to HardSPL.
I went through several versions of the HardSPL and tried installing new drivers for the phone while in bootmode... all with no luck.
When connected through Activesync or Mobile Center, running the HardSPL brings up a confirmation windows on the phone, allowing reboots the device. It gets stuck at the black screen and times out. I've tried manually putting the phone in bootmode and trying it, but never gets past 0%.
I wonder if newer model TouchPro's are coming out with a revised bootloader?
Click to expand...
Click to collapse
Yes they are coming with a new bootloader. I just got my phone replaced from ATT and the new one came with 1.95 version while originals were 1.90. There is no HARD-SPL out for 1.95.
The way to do it now is to flash an old original AT&T rom with the 1.90 bootloader (since it's original, it won't require HardSPL). Then go ahead and everything should work as described in this forum/wiki.
Interseting. Sounds like a winner. Next time he comes around I'll try this.
Any idea where I can get a AT&T older rom that has the 1.90 HardSLP on it? I am having the same issue with the Error 262 update error.
Thanks
smicale said:
Any idea where I can get a AT&T older rom that has the 1.90 HardSLP on it? I am having the same issue with the Error 262 update error.
Thanks
Click to expand...
Click to collapse
You should probably go to your ATT store and tell them you'd like to get the official Hard SPL update.
I am really struggling with this. Do I have to the FLASH HardSPL or can I just go straight to the flashing my preferred ROM. I can not get get the FLASH HardSPL to work because of this Error 262. Please someone tell me where I am going wrong with this!!!! I am bout to pull my last hair out!
smicale said:
I am really struggling with this. Do I have to the FLASH HardSPL or can I just go straight to the flashing my preferred ROM. I can not get get the FLASH HardSPL to work because of this Error 262. Please someone tell me where I am going wrong with this!!!! I am bout to pull my last hair out!
Click to expand...
Click to collapse
If u want to use not the official rom made for ur provider and phone, hardspl is the only way. Any custom rom needs hardspl. Otherwise ur phone will not accept the rom.
But look here http://forum.xda-developers.com/showthread.php?t=410150
and flash the stock 1.90 SPL first, then u are ready for hardspl.
Description how to do stock spl is in this thread. Its normally meant for going back to stock for repair, but it should also solve ur issue.
NOT SHURE BECAUSE IN THE CDMA SECTION, IS UR PHONE CDMA OR GSM. MY SOLUTIUON IS FOR GSM !!!!!!
U SHOULD CHANGE THE POSTING SECTION IF ITS GSM !!!!!
Try doing the HardSPL in a Windows XP machine (needs .NET Framework 2.0 and ActiveSync). Goodluck.
i had the same problem as you and i maybe have a solution for you
go to your usb settings and look if you have a check box saying something about advanced networking. if it is indeed checked uncheck it and your problem will be gone hopefully
i did it on my telus touch pro and i am now able to upgrade my phone to winmo 6.5
Related
Hi!
long time viewer first time poster.
I have G4 CID LOCKED Cingular 8125 with mfrazzz's Crossbow Reloaded 1.7.1 I have wizard love Rom as Base.
I really tried hard to update (I guess it is really a downgrade) my original Radio from 02.25.11 to 2.19.11 but no matter what I do, it failed.
I tried with every romupdateutility_wizard_noid.exe i could find but I get the same result everytime.
ON PC: I get 260 Error (tried in two machines same error message)
and
On my Wizard: stuck in this 3 colored screen. I see 3 color screen with "RUU" in right upper corner and "USB" on left bottom with IPL/SPL version showing in red If i press reset button, it will boot back to mobile windows fine.
Can anybody help me?
My rest device info:
ROM Version: 2.18.0.0 WWE
ROM date:2/14/06
IPL/SPL: 2.25.0001
GSM:02.25.11
Protocol version? 4.1.13.12
ExtROM version: faria V5.0
My Downgrade
All I did was use the rom upgrade utility from the "wizard love rom" (the one that is in Italian) and the T-mobile radio rom listed in the Wiki.
Worked like a charm!
thanks for the reply..
but of course i tried that already.
i think error 260 is communication related issue. PC communicate perfectly with ActiveSync.. but when it reboot for the flashing to occur,it just get stucked as if pc is not communicating with the wizard.
is downgrade to 2.19.11 really worthy?
nic2mit said:
thanks for the reply..
but of course i tried that already.
i think error 260 is communication related issue. PC communicate perfectly with ActiveSync.. but when it reboot for the flashing to occur,it just get stucked as if pc is not communicating with the wizard.
is downgrade to 2.19.11 really worthy?
Click to expand...
Click to collapse
Is your device actually booting up? If so, just download one of the radio ONLY roms. It won't matter whether you have a CID locked phone or not and the radio ONLY rom will not touch the IPL/SPL.
Having said that, is there a reason why you want to downgrade to 2.19? Are you having missed calls issues?
Hi titus666,
I am having the same ROM and missed call issues too.Even when i am on a full coverage area my wizard signals seems to dropping,coming back,dropping ....
What could be the probalem .Any recommended Radio ROMS's.
Probably you read this already
xdawiz said:
Hi titus666,
I am having the same ROM and missed call issues too.Even when i am on a full coverage area my wizard signals seems to dropping,coming back,dropping ....
What could be the probalem .Any recommended Radio ROMS's.
Click to expand...
Click to collapse
A little bit off regarding your initial post but here´s good feedback on how both radios behave.
http://forum.xda-developers.com/showthread.php?t=312834
I've had some problems as well.
I used the tool that came in the download to downgrade to 2.19 (I am having missed calls problem) and it won't.
I'm using a Windows Vista and already did the whole thing to update drivers with the one given on the forum over here, yet, everytime I run the thing it crashes and then I have to go through it all over again.
Its like the driver just doesn't work anymore, even though I have tried "re-updating" it to the one that I downloaded here, unlike the real Roms this one just won't go throguh and wait for the 3 colored screen to come up, just freezes before.
I was trying to upgrade to radio v1.43 in the hope that battery life was improved over 1.41 however when it got to 8% it stopped and gave me an error i can't remember After atempting to recover, it got off the three colour screen now the 3100 stalls on the blackshadow version4 screen (bootloader screen?) and goes no further. I tried reflashing but got a 260 and using mtty, only getting 2 com port options, didn't offer any help.
I'm really sorry to have not been able to sort this with reading through the relevant post but I haven't found a solution. What else can I try?
Hi,
Could you pls advise what is your device made, model, SPL version ... etc.
Also did you try to do Hard reset?
I'm using now black MAJIK (and few days ago black shadow) with radio 1.43 with no problem.
its the SPV m3100 When I decided to go Black shadow I read up on mr vanx and made sure I had all the things I needed. If I remember right, when I came to upgrade to Majik the auto detect found the second option down
SPL-1.04/1.10 - 1.09 Bootloader. I've realized since I had a spaz and ran the RUU from the archive this time. From what I've since read thats not too cleaver.
I have tried a hard reset and took the battery out instead of pressing space.
I dont know if this information on the starter screen is of use
M 05
S 04
B 05 D 3lak
I'm not sure, but hard reset doesnt mean you take the batery out.
Please check that link:
http://wiki.xda-developers.com/index.php?pagename=Hermes_For_Beginners#hardreset
I was in your position (hanged on booting) few days ago, and when i did hard reset, it changes every thing to basic normal condition.
i meant when i did a hard reset when it asked me to press space to reboot I took the battery out. I tried again this time pressing space to reboot but I still get stuck on the loading screen. I can't connect by USB to the PC I'm guessing the drivers on the phone haven't loaded and I'm stuck as to what to do.
Does anyone have any ideas?
try look at it http://forum.xda-developers.com/showthread.php?t=286755
ok I've tried everything I can think of to connect the 3100 to the computer so I can reflash it but mtty gives only com 1 and com2 but no USB and neither those two work, active sync wont connect so I disabled it as suggested and running the radio ruu and wrapper wont querry the device. I am now at a loss as to what to do next someone must know what I should do. Please?
what is your SPL?
try this http://wiki.xda-developers.com/index.php?pagename=HTC_Hermes
sl is 1.09 i'd updated it on the previously successful black shadow flash
msn [email protected]
icq 150277111
AIM TazmanFH9
Yahoo bigfathairyboggart
I have tried changing KITL trasport but I am unable to select or chose either option. I have also tried the rversion command in the tri colour screen but nothing happens. I hope I'm missing something nice and simple but I get the feeling I'm not going to be that lucky. Please help
tcSPVm3100 said:
sl is 1.09 i'd updated it on the previously successful black shadow flash
Click to expand...
Click to collapse
I suggest you check again, press and hold the side OK button and the power button...then put the stylus into the hole in the bottom of the unit.
yeah I've done that it's "SPL-1.09"
I had this exact problem yesterday, with the same bootloader too. The phone would not pass the splash and IT refused to upgrade. I ended up downgrading to a shipped wm5 rom (in my case the cingular 1.30.502.1_1.11.00.00) which to my surprise actually worked as no rom radio or spl upgrade moved at al on my phone. Then upgraded back to black majik. I hope this helps.
Thanks. I downloaded the trial of wm5 from the windows website and it asked me to install .NET framework version 1 so I got that but it turns out to be 2.0 not 1.1 It would say it had repaired but it would say this with or without the phone connected.
tcSPVm3100 said:
Thanks. I downloaded the trial of wm5 from the windows website and it asked me to install .NET framework version 1 so I got that but it turns out to be 2.0 not 1.1 It would say it had repaired but it would say this with or without the phone connected.
Click to expand...
Click to collapse
Just download a WM5 ROM from the wiki page!
ok tried this too no luck.
Trying to use the one from orange (linked to through wikki) I get an 294 invalid vendor error however active sync cannot connect yet of course so is this to be expected?
I have however gotten a connection with mtty which is a step forward dunno what to do with it yet though except trying the password 0000000000000000 command but it not disabling the password. This then lead me to read for a further hour how to change it and I've got to be honest; it beat me. I have No idea what the hell its talking about. My head hurt with so much reading.
I get a no gsm pop up v briefly on loader. I so want my phone back
I have since tried CID unlocker just so i get something installed onto this brick but I either get a connection error or it telling me it can't install for some other reason. I can not set the password in mtty to 0000000000000000 so how do I do that and is this the first step to getting things sorted? "just running a rom install" is not happening I can get a USB connection in mtty and that is it. Is the fact i'm running SPL 1.09 a problem? I'm getting precious little help guys If i'm posting in the wrong place or something please let me know. I need thing thing back now. Hours are drifting by with me trying to get some head knowledge but I still need some guidance please
tcSPVm3100 said:
I have since tried CID unlocker just so i get something installed onto this brick but I either get a connection error or it telling me it can't install for some other reason. I can not set the password in mtty to 0000000000000000 so how do I do that and is this the first step to getting things sorted? "just running a rom install" is not happening I can get a USB connection in mtty and that is it. Is the fact i'm running SPL 1.09 a problem? I'm getting precious little help guys If i'm posting in the wrong place or something please let me know. I need thing thing back now. Hours are drifting by with me trying to get some head knowledge but I still need some guidance please
Click to expand...
Click to collapse
can u flashing HARD V7?,i think better u have IPL 1.04 SPL 2.10olipro first ,then try to flashing radio?
and did u try SD card.
In bootloader can anyone here connect with active sync? I can't so updating rom and radio flashes in the usual way isn't possible. Trying the hard spl again it tells me to make sure active sync is connected and as it isn't it throws back a 262 update error. 0% on the hermes and that's currently as far as I can get. I have no means with which to access the memory card.
The reason you get an invalid vendor ID is because your CID doesnt match....download a ROM which is for your device (an orange one?)...then try.
You need to read the wiki alot more before trying anything else since you are not aware of the vendor ID error...nor the fact you MUST use HardSPL.
I linked to the orange ROM from wikki and tried installing it. it was while installing THIS ROM SPV_M3100_ROMUpdate_0407.exe I got invalid vendor error.
Installing a recent DL on HARD spl v7 I get a 240 open file error that's one I haven't had before.
With all other attempts they all say they want an active sync connection.
I can not connect to the phone through active sync
so all attempts by me to flash anything to the phone using an RUU fails.
All rite here we go, in advanced i thank u guys for trying to help me out here.
First, i'm a n00bie compared with the most of u guys.
My Device:
Tytn Herm 300
OS: Schaps Purple 3.30c
SPL: Hard-Spl 2.10 oli
Radio: 1.16.00.00 !Hmzz...that's the problem!
My phone functionallity sucks...some how it keep loosing connection while i see the phone indication bar up to 3 bars. So i decided to do something about it.
Beeing a noob i thought it got to do something with the OS. So i upgrade it to Schaps's wonderfull purple WM6 Hermes 3.30c and loaded the Hard SPL 2.10 oil V7. All went great, and my Hermes never looked so cool before.
But now i'm trying to upgrade my radio, which is still version 1.16.00.00, to what ever better version. I tried every radio upgrade possible from this list:
http://wiki.xda-developers.com/index...actedRadioRoms
Every single one starts well. passed the information retrieving from my phone. Confirmed the update, and then there was the installation progress bar....
All versions of the radio roms i downloaden get stuck in here. It doesn't even start..0% and error... And really i dun have any idea why.
So after re-flashing a gazillion times, i decided to ask help to the allmighty XDA community. So pls, if anybody there got a suggestion or the solution...i would be so thankfull and will slaughter a goat to worship you
If you've got schaps Rom and HardSPL on your phone then you obviously don't have problems flashing or with PC/phone comms.
When you try flashing the radio, how long do you wait before deciding it doesn't work? I've found that some of them can take what seems like a really long time and I'm tempted to unplug and start again.
Maybe try again, then go make yourself a cup of tee/coffee or get a beer then come back 10 minutes later. If the upgrade still hasn't worked we'll have to look a bit deeper
RaDeNRFX said:
- I am so sorry posting this twice in the wrong sections, it seems that i'm a really noobie forum user - But i finally found the rite section. So my humble excuses.
All rite here we go, in advanced i thank u guys for trying to help me out here.
First, i'm a n00bie compared with the most of u guys.
My Device:
Tytn Herm 300
OS: Schaps Purple 3.30c
SPL: Hard-Spl 2.10 oli
Radio: 1.16.00.00 !Hmzz...that's the problem!
My phone functionallity sucks...some how it keep loosing connection while i see the phone indication bar up to 3 bars. So i decided to do something about it.
Beeing a noob i thought it got to do something with the OS. So i upgrade it to Schaps's wonderfull purple WM6 Hermes 3.30c and loaded the Hard SPL 2.10 oil V7. All went great, and my Hermes never looked so cool before.
But now i'm trying to upgrade my radio, which is still version 1.16.00.00, to what ever better version. I tried every radio upgrade possible from this list:
http://wiki.xda-developers.com/index...actedRadioRoms
Every single one starts well. passed the information retrieving from my phone. Confirmed the update, and then there was the installation progress bar....
All versions of the radio roms i downloaden get stuck in here. It doesn't even start..0% and error... And really i dun have any idea why.
So after re-flashing a gazillion times, i decided to ask help to the allmighty XDA community. So pls, if anybody there got a suggestion or the solution...i would be so thankfull and will slaughter a goat to worship you
Click to expand...
Click to collapse
ach2 said:
If you've got schaps Rom and HardSPL on your phone then you obviously don't have problems flashing or with PC/phone comms.
When you try flashing the radio, how long do you wait before deciding it doesn't work? I've found that some of them can take what seems like a really long time and I'm tempted to unplug and start again.
Maybe try again, then go make yourself a cup of tee/coffee or get a beer then come back 10 minutes later. If the upgrade still hasn't worked we'll have to look a bit deeper
Click to expand...
Click to collapse
I waited till the Program says connection error...and send me to recovery proces. And i've been making hella tons of coffee after trying to flash that many Radio Roms. Any other suggestions? I'm so desperate
Ok, maybe some more info...
Do you see 'NO GSM' during the phone boot process?
Do you have no radio at all or just intermittent reception?
Are you running Vista?
What is the connection error number?
If you've lost the radio but have hard SPL it may just be a case of re-flashing an original manufacturers ROM (which will include the radio) then start your upgrading again afterwards. Don't forget to back-up data before flashing.
If you do flash a manufacturers shipped rom - check that you still have HardSPL afterwards.
ach2 said:
Ok, maybe some more info...
Do you see 'NO GSM' during the phone boot process?
Do you have no radio at all or just intermittent reception?
Are you running Vista?
What is the connection error number?
If you've lost the radio but have hard SPL it may just be a case of re-flashing an original manufacturers ROM (which will include the radio) then start your upgrading again afterwards. Don't forget to back-up data before flashing.
If you do flash a manufacturers shipped rom - check that you still have HardSPL afterwards.
Click to expand...
Click to collapse
Well the weird part is "No GSM" appeared occasionally...some times it shows it sometimes it's not showing it.
No...i'm a Vista hater. And dun have the original manufacturers ROM. I've got the "T-Mobile Vario II" from The Netherlands..so if anybody got a link for the original version i'd be thankfull.
The Radio it self is intermittent and very inpredictable...for example:
Radio indicator says i got full recieve:...but i can't call or recieve any.
Connection error: 262 (which is, if i'm not mistake a connection error.) Which is bull cuz i'm re-running every other ROM's upload with the same way and succeded/
Radio indicator says no reception and shows an exclamation mark:...and my GF just called me to hurry up and pick her up :/
But the weird part is...it seems that my radio ROM is locked somehow. I can upgrade or downgrade SPL's and OS ROM's but not the Radio ROM.
I've tried to use MTTY by now and followed the manual bellow: (Problem 5)
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems#problem5
But it began with invalid password. Procede as written and it didn't helped.
More suggestions are welcome
My bad...i didn't looked well enough. It is saying No GSM the whole time.
More information:
I've checked the Device information on the Hermes now some information are blank:
Radio: Blank
Protocol version: Blank
IMEI: Blank
All other information field are filled. Been spending hours reading tutorials and manuals...and nothing. HELP!
OK,
This isn't a problem I've had myself, but loads of other people have and there are quite a few threads on how to unbrick from here... you're going to have to do a bit of reading.
This page shows the different combinations of OS/radio/brick type etc and should point you in the right direction for the correct course of action http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
Then read through this thread http://forum.xda-developers.com/showthread.php?t=286755 . It's got really long but read the beginning where POF describes the types of problem and also the solutions. Then it's probably best to jump to somewhere near the end and pick someone who has a similar problem.
It sounds to me as though you need to just flash a radio in nbh format, but please do some more reading before you do this to check my advice - as I said at the beginning, I haven't had this problem so I'm only giving advice from what others have written.
ach2 said:
It sounds to me as though you need to just flash a radio in nbh format, but please do some more reading before you do this to check my advice - as I said at the beginning, I haven't had this problem so I'm only giving advice from what others have written.
Click to expand...
Click to collapse
I am really thankfull of ur post. Unfortunately, i've been doing some reading. Including the link u gave me. The problem is that i can't upload/flash Radio in nhb format.
As i described in the first place, i can't load a nhb format radio in RUUWrapper.exe properly. It can start the proces..but it always end up with a connection error code 260/262 during the installation progres bar (0%).
The solutions some ppl tried in ur link is often not my case. And the similar cases i have tried where i end up with the same grumpfy situation.
have you tried to flash the radio using the SD card method? I too have a cable connection problem but I fear mine may be hardware failure.
Yap...and no luck
Hi all,
First of all I want to let you know that I did search the forum for a solution. In fact, I found a lot of workarounds but none of them actually worked.
Let me give some details about my problem: My Hermes was working fine. I was running the official WM6 ROM supplied by HTC, so no customized ROM here.
It was going fine until the WM frozed. Then I soft reset the device and after that I never got cellular signal again.
While booting the device I got the message: "no GSM".
First thing I tried was to flash a new radio ROM. In all the attempts the progress bar never moved from 0% and after a while I got the communication problem error.
Then I tried flashing a whole ROM. This time the progress bar stopped at 81%. Apparently in the first 81% it flashes the OS and in the last 19% it writes the radio. Anyway, I tried this a few times and never finished.
In fact, after every communication error message I got stuck in the bootloader screen.
The only thing that works is to flash a ROM WITHOUT the radio!!
Is there anything I can do to save my phone or am I condemned to use my Hermes as a phone-less pda?
I tried everything I found in the wiki/forums, but I couldn't find a working solution.
I suspect that the blocks of memory where the radio data reside got corrupted, could that be possible?
PLEASE HELP!
thanks in advance!
Chris
A similar thing happen to me several months ago. While on a call my phone froze and when I soft-reset it the dreaded 'No GSM' issue appeared. I tried flashing radios/full roms/etc, but nothing worked. I ended up sending my phone to the htc repair facility and they fixed it at no cost. (Other than not having a phone for ~10 days)
Thanks dang, but I don't have a HTC service center where I live (Argentina, LATAM)
I'm faithful that the people of this wonderful community will be able to help me.
Just for curiosity, where did you send your device? Is it in the US?
cheers
sounds like a hardware problem to me...
Hi, there! I found that a lot of us who have bricked our Hermes, don't have a responsive radio bootloader, so when they try to flash a full rom, the progress bar hangs to 13%, or 81%. This is because at that time the flasher is trying to enter the radio bootloader, but because it's corrupted, it hangs. Till today there is no known solution to this one. I'm far away from England where I bought my Hermes, so I'm not thinking to send it back for repair. I'm a programmer, so my knowledge may be usefull here. The first thing I must know is if i can use the "lnb" command without being SuperCID. I mean if there is something like a Hard-SPL with an "lnb" command - (or renamed for security reasons). Maybe there is hope!
How can I try that?
windshearx said:
The first thing I must know is if i can use the "lnb" command without being SuperCID. I mean if there is something like a Hard-SPL with an "lnb" command - (or renamed for security reasons). Maybe there is hope!
Click to expand...
Click to collapse
You can use 'lnb' in HardSPL without having a real SuperCID; however you will not be able to flash a radio with 'lnb' command. The radio chipset has its own bootloader, the and the SPL just acts as a pass-through sending the data directly to radio chipset through the s2410 UART.
I had one device with non-responsive htc_boot and tried all kinds of SPL patches to flash htc_boot again on radio, without success. The only known method to fix this is to take the BGA chip out with hot air and reflash it with special hardware, as it is not common to have this equipment at home, your only option is to send it somewhere to do it for you.
However, I don't want to discourage you to research on it, maybe you find something i didn't
I have a similar problem
I also have a NO GSM and corrupted CID but I can access KITL and use it with PB 5.0. and I followed this steps here but the phone doesnt boot completely. It stops just after the two boot screens on Black WM6 ending on a white screen and the debug window on PB after loading all sort of things begin showing these lines over and over:
@@@@@@ HUB state changes now @@@@@@
[HDC]HubStatusChangeThreadPN TRUE
[HDC]HubStatusChangeThreadPN FALSE
Is there any hope for me? I have the cingular 8525
thanks
Gents, do you think the solution presented in http://forum.xda-developers.com/showthread.php?t=280425 could help me?
Please advise.
thanks again
chriscec said:
Just for curiosity, where did you send your device? Is it in the US?
Click to expand...
Click to collapse
I sent it to the HTC service center in Texas, US.
I just got my replacement from ATT.. Had the same problem. Its a hardware problem.. I wouldnt waste anymore of your time.
first, i'm sorry for my english
I've the same problem with a V1605 (french SFR), i've tried every solution but flash radio doesn't work.
I can flash cooked os without any problem, but it's impossible to put official
It's only a pda now, it's better than a brick
My hernes use to be the same as you 'NoGSM'.I tried to install the official rom,but it 's not work at all.I called to service center ask this problem,so they said that it must be only changed the mainboard. That 's terrible!!!
for ALL -that has NO GSM and stuck at OS boot,
please follow this link -
http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
the link above help me to bring back my hermes alive (about four hours work).
otoro_315 said:
for ALL -that has NO GSM and stuck at OS boot,
please follow this link -
http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
the link above help me to bring back my hermes alive (about four hours work).
Click to expand...
Click to collapse
That only works with phones with KITL...which I don't seem to have.
Sorry, how to config the phone with KITL and solve the no gsm problem.
No GSM but when sim inserted
Hi all, First sorry for my bad english.
I also have 2 bricked Tytn Hermes 200. Its not my personal ones Its my company's property, which pple were using this phones. So i'm facin with problem which many pple here having but with exception. both phones having no gsm error when sim inserted but without sim its fine. In other words , device info showing every info including IMEI when sim unavailable. And some times works with sim but after making few call and receiving phone hangs(not system) and goes off from network but anthena signal still showing few bars. I'm thinking maybe the radio hangs totally and goes off, and after soft restart NO GSM. I also tried many flashing upgrading those things nothing can really help me.
When im flashing original rom from HTC (the latest one HTC_TyTN_WWE_3.54.255.3_6275_1.48.00.10_108) its hanging on 12% and doing 3 or 4 times recovery , but its finishes succesfully. So what exactly happening in 12th%?. Maybe its started flashing radio and stopped on bad block ? But then why its finishes succesfully after few retry?. Ok so if any one wants to experiments on the phones except radio welcome. I'll help. And some can give me quick example of how to check bad blocks?.
Tnx.
@akarandomjames -
#1. have you try the comm button+reset button hold for 2-3 seconds
#2. OR try the comm button+OK button+reset button hold for 2-3 seconds
anyway, i'm not sure if KITL is dependend on the ROM version. because when my device was in NO GSM status, SPL is 1.04, HTC bootloader is 0108, and lost SuperCID. Because of my device is still has SPL 1.04, i was able to load WM5 full ROM upgrade using WWE HTC English QTEK_001 2.05.255.1 01/17/07 version (ROM available on this site under HERMES Upgrade link), run it twice. once you have successful load the WM5 ROM then try to do step #1 or #2 above to get KITL USB display on your screen device.
Note: i don't think KITL mode is not available once your device is in Production Mode. anyone here can verify this?
otoro_315 said:
@akarandomjames -
#1. have you try the comm button+reset button hold for 2-3 seconds
#2. OR try the comm button+OK button+reset button hold for 2-3 seconds
anyway, i'm not sure if KITL is dependend on the ROM version. because when my device was in NO GSM status, SPL is 1.04, HTC bootloader is 0108, and lost SuperCID. Because of my device is still has SPL 1.04, i was able to load WM5 full ROM upgrade using WWE HTC English QTEK_001 2.05.255.1 01/17/07 version (ROM available on this site under HERMES Upgrade link), run it twice. once you have successful load the WM5 ROM then try to do step #1 or #2 above to get KITL USB display on your screen device.
Note: i don't think KITL mode is not available once your device is in Production Mode. anyone here can verify this?
Click to expand...
Click to collapse
My device is still SuperCID and I know I don't have KITL...I have SPL 1.04 as well and HTC Bootloader is 0108. I can't install any ROMs with radios as they will hang at 11/12%. I will attempt this "overload" method where it seems some people have had luck with it...after a few recoveries it just finally installs...but I don't think that will be the case.
If I can't fix this in a few days, I will most likely use my warranty or just wait for the Kaiser.
My variation of No GSM
I feel like I have problem 1A...where I am able to boot into OS but no GSM.
I am still SuperCID, SPL 1.04, HTC Bootloader 0108. Last known radio before corruption was 1.48.00.00. ROM where this problem occured: VP3G 3.60.1.
I was not even in the middle of an upgrade...just a soft reset after my phone ALREADY lost GSM capabilities during a tether session. It was stuck with no signal in Phone Mode...I put it in Flight Mode...then tried to move it back to Phone Mode and it wouldn't do so. I soft reset...and the no GSM stuck.
I tried to reinstall radio...many errors...stuck on bootloader. At first, OS's only were not installing as well but I got past that. Now I am able to boot into OS's with limited capabilities...and they will NOT ACTIVESYNC at all. Regardless of how old or new the ROM is. I tried older OS's that I knew worked in the past for me...but they refused to activesync.
Due to that, I am not able to install latest HardSPL 2.10Oli via SSPL. That seems to be the only way to do it according to my knowledge and what I've read. Maybe mtty was capable but I'm not sure. HardSPL 1.40Oli wasn't giving me any problems though, but I just wanted to have the latest one so I can avoid IPL damage.
I can only install anything if I start the device in bootloader...and I'm only limited to the OS since my Radio Bootloader seems corrupted.
I'm not sure what caused the corruption in the first place...but I feel annoying now posting on different parts of the forum with a problem that seems to be growing in the community.
Hi guys. Mass apologies for my stupidity, but here goes...
I have now spent over 2 days on this site reading all that I can, but I am at a loss and desperate for your expertise!
I am running a UK Tmobile Vario 2. I was having problems with the phone crashing constantly and not getting any signal at all so I installed WM6 yesterday hoping this would help. Its not crashing as much, but its still not getting any signal.
After reading loads of threads and posts all over the place (I have read enough WIKI to make my eyes bleed), I think I need to update the radio version. This is the information I can gather from my phone:
Bootloader info-
Herm300
IPL-1.04
SPL-2.03
I cant figure out how to enter commands in bootloader to gather any more info I tried the mtty.exe thing with no avail. When I go to "device information" it reads like this:
ROM version: 3.60.110.4
ROM date: 09/05/07
Radio version: SAYS NOTHING!!!!
Protocol version: SAYS NOTHING!!
IMEI: SAYS NOTHING!!
When I do a soft reset I get red letters and numbers appearing and not the "no gsm" message.
This is a 2nd hand phone off of ebay as my original phone was stolen. I have contacted Tmobile, but they refuse to help me as its not the original phone that I bought.
I would be most grateful for any help you can give me!!
Thanks,
April
OK, firstly.....flash hardspl.........instructions here
Next flash ANY radio......try version 1.48.00.10.
with the device booted up and synched with Activesync, download the radio ROM, unzip and run the RUUprogram (the only exe in the zip).
select autodetect, it should highlite SPL v2.10 and tick the "HardSPL?" box.
go through each screen and accept everything......the radio will be flashed.
Hopefully your device will work properly after this.
uh oh...
Thanks so much for your speedy response. Obviously I managed to screw this up.
got to this stage
"select autodetect, it should highlite SPL v2.10 and tick the "HardSPL?" box."
It didnt autodetect, so selected SPL v2.10 and ticked "HardSPL" box manually. Went through all the other bits and when it starts to do its thing it just sits at 0% then i get error message "ERROR 262: UPDATE ERROR. The rom update utility has encountered communication errors during the update process. THe program will guide you step by step to recover from the errors so you can continue with the update."
So I followed the recovery process instructions several times. Nothing has worked. Have tried restarting my computer and doing a hard reset on phone, and stuck with the bootloader screen reading IPL 1.04 and HERM300 SPL-2.10.01Olipro.
Manage to get back to this stage
"select autodetect, it should highlite SPL v2.10 and tick the "HardSPL?" box."
and go through the ticks but always ends up with error message 262.
SORRY!
Sorry to hear about your problems.
Was it the official T-Mobile WM6 ?
If so it was another 1.50 Radio!
I have same now!
http://forum.xda-developers.com/showthread.php?t=357275
I read in another thread try putting phone in fridge for 15mins first without the battery.
Good Luck
fridge vs. floor
Yes, it was the official WM6 from T-Mobile.
Im worried now that my limited experience with flashing, cooking, and now crying will leave me with a proper "brick".
I will try the fridge thing, if I ever get it to loads WM6 again but for the mean time, I will continue to throw it on the floor.
What do you mean by it was another 1.50 radio? I dont know what version I once had, but as suggested by mrvanx, I was trying to upload the 1.48.00.01.
Again apologies for my complete ignorance, but Im sure there are others that share my stupidity and will benefit from me asking goofy questions. If anyone else has any more simpleton advice on how to revive my poor phone, I would be much obliged!
Thanks,
April
The 1.50 radio bit; If it was the official T-Mobile WM6 upgrade, then your radio will have been 1.50 (I am pretty sure)
I dont know what else to do!!??
Ok since trying to update my radio from nothing to 1.48.00.01 and receiving error message 262 during the update, my phone now only goes into bootloader mode reading the following:
HERM300
IPL-1.04
SPL-2.10.0lipro
I have tried the following to bring it back to life (but not in any particular order):
- restarted my pc several times
- made sure my Windows XP SP2 was up to date
- made sure I had .net framework up to date
- hard reset on phone
- soft reset on phone
- leaving battery out overnight
- updating SPL to 2.10.0lipro (again) doesnt get to any percentage, just straight to error 260
- updating radio to 1.48.00.01 (again) - wont autodetect. tried radio button SPL2.10, then just force safe, then just HardSPL. each option dies at 0% then error message 262)
- reinstalling TMobile version WM6 (again) - dies at 11% - error message 262
I saw the post by pof "How to unbrick your bricked hermes" and the solution was to "Flash any radio in NBH format", but I cant figure out how to do that!? (I have tried clicking on the nbh file in the downloaded radio folder, but dont know what program to use to unload all the info. Have also looked at all the links on "Radio sudden death issue knowledge consolidation" and nothing has helped.
Sorry again guys, but can someone please help
If not, does anyone want to buy my brick?
alachlan said:
Sorry again guys, but can someone please help
If not, does anyone want to buy my brick?
Click to expand...
Click to collapse
Dude - there are enough bricks around these parts to build a 500 story repair centre! All we need is MS to merge their NT, CE and ME technologies into CEMENT then we can hold all the bricks together
Error 260 (comms error) is usually caused by using Vista without "fixing" it or Win2K/XP without the .net framework on it
Error 262 is USB port not available - turning hermes off and on (or removing the battery if that fails) at that point and putting it manually into bootloader usually cures that one then continuing with the flash.
Incorrect.
Its more than likely this Vario II was irepairably bricked before the TC bought it, the Radio upgrade is failing on a Tmobile official ROM (which includes a radio) and on a standard CustomRUU upgrade for the radio only.
A "checkimage" command in mtty would probabaly return a failed radio checksum and following on from that the mtty commands to get into the radio bootloader will fail (rtask a......then rversion).
Also there may be a corrupted CID on the device which again isnt good.
Ive seen these types of bricks MANY times.
Sorry dude, looks like your Hermes was a paperweight when you bought it.
Never thought of that - shameful given the amount of radio investigating I've done recently Too busy on 260's with part flashes from people not installing .net (also the amount of hits you should be getting to your vista guide now is scary!)
Still say we should collect up all the bricks and build a repair centre
Mikeapollo said:
.....the amount of hits you should be getting to your vista guide now is scary!....
Click to expand...
Click to collapse
73039 hits according to the site
Pretty much the only fatal brick now is a damaged radio/CID flash. If there was a way for Olipro/Pof/Us to flash a hardspl type package in place of the radio bootloader then it would be solid.
What type of mortar should we use?
mrvanx said:
73039 hits according to the site
Pretty much the only fatal brick now is a damaged radio/CID flash. If there was a way for Olipro/Pof/Us to flash a hardspl type package in place of the radio bootloader then it would be solid.
Click to expand...
Click to collapse
Yup.. Must admit I think that's the one thing that will not happen anytime soon as the interactions between bootloader, radio bootloader and the radio PLA/PIC is a tad complex... It'll be a very difficult thing to test and even finding a suitable vunerability is difficult - certainly beyond my abilities presently. Though the same was said 12 months ago about the No-Wifi issue and Olipro led some excellent progress in that area...
Mind you - the key to fixing CID/radio bricks is to educate the masses not to make them in the first place and not to just blindly execute whatever they stumble across - more of a challenge than rewriting the bootloader by hand on paper tape and almost as frustrating
Oh... as for Mortar... we could have a mass scrape of all that weird dirt stuff that "grows" under the "invisible-until-you-open-it" edges of the screens and around the battery cover and add a drop of water
Wonder if it's the electronic equivelent of belly button fluff?
does that mean its dead?
Thanks for all the entertaining posts guys. Just to clarify things, Im running XP SP2, and the phone did actually work for about 3 months until suddenly one day it gradually started dropping signal, until the signal vanished completely.
Are you guys trying to tell me that my phone is completely dead then? Could I have prevented this by knowing what the hell I was doing or was it a fault of the phone?
With regards to the mortar issue I think a combination of tears and sh*t would do. I think I would build a big wall around the jackasses who release products that arent completely stable but still charge us an arm and a leg for them. (excuse my grumpiness)
Oh and just wanted to say that since my vario has been out of action, I have been relying on the trustiest brick Ive ever owned, my XDA IIs. This thing has been dropped so many times and is held together with super glue, but it does the job and gets on with things, just not very quickly.
Thanks again for all the help.
alachlan said:
Thanks for all the entertaining posts guys. Just to clarify things, Im running XP SP2, and the phone did actually work for about 3 months until suddenly one day it gradually started dropping signal, until the signal vanished completely.
Are you guys trying to tell me that my phone is completely dead then? Could I have prevented this by knowing what the hell I was doing or was it a fault of the phone?
With regards to the mortar issue I think a combination of tears and sh*t would do. I think I would build a big wall around the jackasses who release products that arent completely stable but still charge us an arm and a leg for them. (excuse my grumpiness)
Oh and just wanted to say that since my vario has been out of action, I have been relying on the trustiest brick Ive ever owned, my XDA IIs. This thing has been dropped so many times and is held together with super glue, but it does the job and gets on with things, just not very quickly.
Thanks again for all the help.
Click to expand...
Click to collapse
By the sounds of it you might have a permenant brick but unless i had your device here and actually went through everything myself i cant be sure. take a read through the sticky thread above this one about unbricking......it will take some time to read through but you will see what techniques are used to try and revive the device.
when cid corruped with spl 2.03 and not have gsm no solution can not flash with sd card when you see that level=fff only when level=0 in mtty console can use sd card for flashing rom.
THIS TIME ONLY SOLUTION TO UNBRICK HERMES WITH SPL 2.03 NO CID AND IMEI -
SENT Imei-check to fix this ??
?
uuuummm....
Thanks mbsshop1302gsm for the response, but did I mention that I have limited knowledge on this stuff? So the more basic the instructions are, the better.
Thanks,
April