Related
For the past 6 hours I have been trying to make the No GSM error message on my Cingular 8525 go away. I cannot use the phone to make any calls whatsoever. I originally unlocked the phone to work with T-Mobile which worked for about 2 months and now this error message. The last and only ROM image that I can load to this phone is the Schaps_WM6Pro_WWE_3.60a-0823_Full.exe. Any other ROMs I try to load either does not pass 0% or goes to 12% and freezes. I tried to follow the unlocking steps again but it ROM upgrade part would not pass 0%. So, I loaded the Schaps_WM6Pro_WWE_3.60a-0823_Full.exe again and checked the Device information. In there I do not see any radio version. The other ROM it loads also is Schaps_WM6Pro_WWE_3.54b-0804_Full.exe. NO other ROMS will load. And even if I load the 3.54b or the 3.60a ROM from Schaps and check the Device Information. It only shows the ROM version and the ROM date. Theres no info for Radio version: or Protocol version. What can cause this and also I think that is the reason why my phone is not recognizing the SIM card. I need a way to put a radio version on this phone. Also, I tried 3 different SIM cards and none works. So if someone can point me in the right direction I would really appreciate it. Thank you.
Well, here would be a good place to start... you should try posting your message there.... do some reading...
Intensefactor,
How much reading and research did you do before you attempted to upgrade the ROM on your phone? Can't be that much else you would know that Schaps ROMS don't have a radio built in.
Have you looked at the mrvanx guides and the other info availableon here?
WB
I read as must as possible yesterday and I still cannot flash any ROM with a Radio version in it. Any ROMs that does not include a radio version like the original ones I flashed can be flashed to the phone. Other than that no other ROMs can be flashed to the phone. Or even flash a radio version separately. I even tried following http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=62&Itemid=26. How can I flash a radio version to the phone? Any help would greatly be appreciated. Thank you once again.
Is there anyone that can at least point me in the right direction?
thanx god there's someone facing the same exact problem i do have ,
now XDA guru's can you please help a little bit me and this man ??? coz i've spent the past week reading this forum and the wiki to figure out a solution with out luck , frankly i was shy to ask so i wont be called a noob .
please help me to solve this problem in my hermes , now i have installed "GM360Gold-WWE_Final" and the phone is working but no radio at all and the device halts sometimes .
the main reason of this problem i guess was when i upgraded to this rom "RUU_Hermes_TMO_UK_3.60.110.4_6275_1.50.00.00_108_T est.exe"
in this thread http://forum.xda-developers.com/showthread.php?t=328626
plz at least tell me whats the problem to avoid me breaking this device
thank you all
I am in a very similar situation !!! POF or somebody please answer
Guys,
Will these threads help?
http://forum.xda-developers.com/showthread.php?p=1515122
http://forum.xda-developers.com/showthread.php?t=325748
http://forum.xda-developers.com/showthread.php?t=322231
WB
Maybe i'm the unlucky one out of the bunch. Now myphone is stuck on the tri-color screen with HERM100 IPL-1.04 on the top left and HERM100 SPL-2.03 under it. The only way I can get my phone to come on is with the 3 key soft reset. If I hit the power button on the phone all it does is show the green light on the top of the phone. So, I cannot even hit the power button to get the phone on no more. I have to Hold the Power, OK and the Soft reset buttons just to get to the tri-color screen now. If I try to flash any ROMs without a radio, it goes to 1% then the phone reboots and goes to a blank screen again. If anyone have any other ideas. Please reply to this post. Reading and reading hasn't really gotten me anywhere. Maybe some explanation from someone might help now. So, please if someone help give me some advice, I would appreciate it. Thank you.
intensefactor said:
The only way I can get my phone to come on is with the 3 key soft reset. If I hit the power button on the phone all it does is show the green light on the top of the phone.
Click to expand...
Click to collapse
I have exactly the same problem, someone must be able to help us
Can you contact me via MSN messenger at: [email protected]
or if you don't have MSN let me know what you have so we can chat
What exactly were you flashing onto the hermes when the problem of the blank screen and green light began?
hey guys,
I tried to update the new custom ROM's, but after I ran the new SPL-unlocker (I installed dcd's new rom while at bootloader =))....now I stuck!!!! my phone won't connect to my activesync anymore....it just froze at i guess "startup"?.....have that silver symbol "htc," "smart mobility."
humnz what should i do now? is there anyway of fixing this problem? anyone know???
Thanks in advance guys...
ps. i understand what i did was a purely an idiotic thing....please pull me out of this mess...........
HellpppPp!!! anyone??? Pleaseeeee
I'd try flashing a different ROM. you could try doing the stock ROM, or you could try a custom one like DCDs.
did you run "titanunlocker.bat" and follow all the instructions?
I think if you hold down the power and camera buttons when you hit reset it will come up and the multi-colored boot screen and you can reflash from there.
I could be mistaken on the key sequence. do a search, I bet you can find it if that don't work.
Thread Close!!!!
Thanks For The Help....
OK I got this too on 6.1 the first time.
Listen.
Turn off allow bt connection and actviesync autoconnect when first connected under connection settings.
Put your phone back into bootloader 2.4 and then flash DCD's rom again.
Let us know if that doesn't work.
oops forgot last part.
After successful Flash ... Re-check options you un-checked.
if its hanging at the splash you dont have all parts installed. spl, rom, AND RADIO
I have searched and searched these forums and have seen several other people with this problem but no solution. I have also looked through the wiki to no avail, so if someone can give me an answer I would really appreciate it.
I have been able to get into the bootloader screen (the r-g-b white stripes) however there is NO text (no serial, no usb) on the screen and it is not recognized by any pc. Can't get any response from mtty.exe because it can't see the USB port. Have tried on multiple PC's...
Is there another way to resurrect this athena or is it DOA?
Thanks,
-Alex-
Some pics of problem...
Blank bootloader...
Please help!
Did you try reflash by SDcard?
http://wiki.xda-developers.com/index.php?pagename=Athena_SD_Card_Flashing
jas_pik said:
Did you try reflash by SDcard?
http://wiki.xda-developers.com/index.php?pagename=Athena_SD_Card_Flashing
Click to expand...
Click to collapse
Yes...no joy.
Just stays on the tri-color screen with no indication that it is reading the card.
Thanks for the advice though!
Did you try resetting - camera button and reset button on the back (I think...) pressed together.
Forum search will tell you exactly...
ssutherland said:
Did you try resetting - camera button and reset button on the back (I think...) pressed together.
Forum search will tell you exactly...
Click to expand...
Click to collapse
Yes, tried the hard reset (camera + reset) the alternate reset (comm + camera + reset) and even the other reset (volume slider + camera + reset). And yes, I was pushing down firmly on the camera button.
Each reset brings me to the tri-color bootloader screen with NO text. No model number, no OS version, no "USB" / "Serial"....just the red-gree-blue-white stripes.
I have looked extensively at all the forums, used the google search for the site and combed the wiki with no luck.
So do you think it is a lost case?
-Alex-
Hello,
sorry for what's happening to you. Can you tell what led to this situation ? Were you trying to unlock your phone or just flashing a new rom ?
luthor_70 said:
Hello,
sorry for what's happening to you. Can you tell what led to this situation ? Were you trying to unlock your phone or just flashing a new rom ?
Click to expand...
Click to collapse
I was trying to load a new ROM but I assumed that I had to use the OliPro unlock first.
Got to the radio flash and that is where it crapped out.
Now that I have read a little more carefully it looks like I don't need to use the OliPro beyond the first step for the stateside unlocked 7501.
Thanks,
-Alex-
when your on bootloader ? does windows detect a usb generic device ?
Nope. Tried 3 different PCs. Shut down all the activesync processes. No luck. No detection that anything is cabled to the advantage.
I am thinking that it is warranty time.
Damn, I hate this....its just the principle of the thing...
-Alex-
bairda said:
Nope. Tried 3 different PCs. Shut down all the activesync processes. No luck. No detection that anything is cabled to the advantage.
I am thinking that it is warranty time.
Damn, I hate this....its just the principle of the thing...
-Alex-
Click to expand...
Click to collapse
Key rule to remember is to always make sure the Advantage is Fully charged. Try charinging it and reflashing it with the factory rom, located here. http://www.america.htc.com/download/RUU_Athena_HTC_US_2.19.453.4_105_1.47.51.00_Ship.exe. Keep us posted and let us know how it went
have you removed the sim and memory card
just checking basics
try that with a full charge and then enter bootloader and connect to usb
Thanks for all the help! I gave up and warrantied a new unit where I WAS successful in loading a new ROM.
I have learned several valuable lessons in the ROM upgrade process. This was on an advantage 7501, unlocked, USA version. I did the upgrade the process with the OliPro 3.0 unlocker, the PK Rom 3.0 and vista pro (32bit):
- Make sure that you have NOT customized your athena/advantage beyond the basic calibration and cut/paste walkthrough.
-Download ONLY THE MOST RECENT VERSION OF THE OLIPRO UNLOCKER. CHECK TWICE TO MAKE SURE THAT YOU HAVE THE LATEST.
-You MUST let step one of the Unlock complete. With the latest version this will make a bricked Advantage practically impossible.
-Go through step 2 & 3 even if you don't think you need this. It will upgrade the radio and give you peace of mind if you are updating to the PK rom.
-Don't panic if you complete step 1 and goof step 2/3. You can recover. But if you screw up the initial SPL unlock in step1...it is not going to be pretty.
Hope this helps!
Thanks for everyones advice!
-Alex-
hello folks,
first off thanks to all the people who help make this forum better and better.
have used you're help a few times especially trying to flash a rom. but now there's a problem... I've installed artemis Rom a couple of times but I wanted the newest so I've downloaded it, flashed my hd2 with task29 like always. pressed vol. down button it restarted until white boot screen. ok, possible, so I reset it and press vol. down again. but still white boot screen. after trying it for 70(!) times. I used the forum. saw that maybe hooking it up to pc and starting custom rom .exe should work. but no. wont even start when hooked to a computer. so please help!
Info:
Cotulla hspl 1.42.00
Task29 by dooloop performed( got stuck after that)
Rom Artemis. 31.5 (current) 35.1 (wanted to install.
Thanks In Advance
Maajelvv
Two possibility's;
Tray to do a hard reset,
Ore tray to install Stock Rom!
tried hard reset. (pulled out battery waited 20 sec. then put it back in. pressed vol. down and power button.) didn't work for 30 times...
have put leoimg.nbh on sd card. but can't get to the tri-colour bootloader so can't install anything...
Thanks for you quick response by the way.
If I get into bootloader there should be no problem but I can't get there :S
I'm out off Idea; tray to send Sir Sternas a PM with your question, maybe he get some Ideas; ore tray to ask this question on the Artemis Thread, there are also helpful peoples out there!
Edit; I just add your question on the Artemis thread!
http://forum.xda-developers.com/showthread.php?p=8450678#post8450678
you haven't made hard reset. if you wont to do hard reset you have to press both volume buttons and then pres power buton ( or press red button near batery ).
also try to make a goldimage ( search the forum ).
regards
Maajelvv said:
tried hard reset. (pulled out battery waited 20 sec. then put it back in. pressed vol. down and power button.) didn't work for 30 times...
have put leoimg.nbh on sd card. but can't get to the tri-colour bootloader so can't install anything...
Thanks for you quick response by the way.
If I get into bootloader there should be no problem but I can't get there :S
Click to expand...
Click to collapse
As Luka1111 said, you haven't done a hard reset. Check this out:
http://www.smartphonegurus.com/forums/topic/8829-hd2-how-to-soft-reset-hard-reset-and-place-in-bootloader-mode/
Dmm;
That I didn't see/read it correctly the way he did a hard reset??
I think it is HSPL 1.42 or an old RADIO-ROM.
System specs for Artemis are SPL 1.66 or above and RADIO 2.07.51.22_2 or above.
Install newest Stock ROM with the mentioned versions or flash HSPL and RADIO manually.
Best regards
Uli
Sorry, have not read you can't access tricolor bootloader. Have you tried without SIM and SD? If not try to flash HSPL and RADIO without SIM and SD.
Maajelvv said:
tried hard reset. (pulled out battery waited 20 sec. then put it back in. pressed vol. down and power button.) didn't work for 30 times...
have put leoimg.nbh on sd card. but can't get to the tri-colour bootloader so can't install anything...
Thanks for you quick response by the way.
If I get into bootloader there should be no problem but I can't get there :S
Click to expand...
Click to collapse
What´s the size of your SD-Card? Flashing from SD works only with max. 8 GB - Card, 16 GB or more won´t work! (Own experience!)
Can you connect your device to ActiveSync? Or otherwise stated: What happens when you connect your device to your PC? Does ActiveSync or Windows Mobile Device Center even startup?
BTW, what happens when you start your device now? Does it hang or just load your old Artemis version??
regards, Kuzibri
uli71 said:
I think it is HSPL 1.42 or an old RADIO-ROM.
System specs for Artemis are SPL 1.66 or above and RADIO 2.07.51.22_2 or above.
Install newest Stock ROM with the mentioned versions or flash HSPL and RADIO manually.
Best regards
Uli
Sorry, have not read you can't access tricolor bootloader. Have you tried without SIM and SD? If not try to flash HSPL and RADIO without SIM and SD.
Click to expand...
Click to collapse
Hi Uli,
the poor man cannot enter bootloader mode and, as I understand from his posts, not connect to his PC. So how can he flash HSPL and/or Radio? There must be something fundamentally wrong with his device, but I also had a similar problem a few weeks ago and, although it took a lot of time, I managed to get it to work again.
BTW, as I already mentioned SPL 1.42 is not the problem.
regards, Kuzibri
kuzibri said:
Hi Uli,
the poor man cannot enter bootloader mode and, as I understand from his posts, not connect to his PC. So how can he flash HSPL and/or Radio? There must be something fundamentally wrong with his device, but I also had a similar problem a few weeks ago and, although it took a lot of time, I managed to get it to work again.
BTW, as I already mentioned SPL 1.42 is not the problem.
regards, Kuzibri
Click to expand...
Click to collapse
Hey Kuzibri, You are absoluteley right. I get no connection true active sync or anything. I'm pretty sure there's something really wrong here. never had this problem before. btw I've mistaken with
my spl version. it's the one Sir Sternas recommended. Spl 1.66 HSPL.
I'm Really confused right now. and Pissed off at the same time...
I mean I loved my HD2 with Artemis Rom close to beeing perfect.( installed Igo8 witch right before I went on holliday, stopped working but mannaged to get TomTom navi to work ) then suddenly my answer button stopped working. so I figured let's install a new Version of Artemis rom. I backed up all my files using microsoft my phone. then used task29. done. So I tried to get to the bootloader.... Nothing. tried attatching it to the pc and hoping it would start if I pressed the custom rom .exe (Read somewhere id might work) Nothing not even a blank screen for startup. now I've got nothing else I can think of. please, U guys have given me so much good suggestions.
Thank you all for your time and your efforts to help me solve this issue.
Maajelvv
kuzibri said:
Hi Uli,
the poor man cannot enter bootloader mode and, as I understand from his posts, not connect to his PC. So how can he flash HSPL and/or Radio? There must be something fundamentally wrong with his device, but I also had a similar problem a few weeks ago and, although it took a lot of time, I managed to get it to work again.
BTW, as I already mentioned SPL 1.42 is not the problem.
regards, Kuzibri
Click to expand...
Click to collapse
Maajelvv said:
Hey Kuzibri, You are absoluteley right. I get no connection true active sync or anything. I'm pretty sure there's something really wrong here. never had this problem before. btw I've mistaken with
my spl version. it's the one Sir Sternas recommended. Spl 1.66 HSPL.
I'm Really confused right now. and Pissed off at the same time...
I mean I loved my HD2 with Artemis Rom close to beeing perfect.( installed Igo8 witch right before I went on holliday, stopped working but mannaged to get TomTom navi to work ) then suddenly my answer button stopped working. so I figured let's install a new Version of Artemis rom. I backed up all my files using microsoft my phone. then used task29. done. So I tried to get to the bootloader.... Nothing. tried attatching it to the pc and hoping it would start if I pressed the custom rom .exe (Read somewhere id might work) Nothing not even a blank screen for startup. now I've got nothing else I can think of. please, U guys have given me so much good suggestions.
Thank you all for your time and your efforts to help me solve this issue.
Maajelvv
Click to expand...
Click to collapse
Hey guys,
maybe you haven't read my whole posting: Have you tried to get access to tricolor bootloader without pluged in SIM and SD?
If you had trouble with your answer button before flashing, is it possible your volume button is also without function? Therefore it seems to be a hardware problem.
Sorry, if this is not the answer you would like to read, but the advise to test without pluged in SIM and SD is my last. Entering bootloader is a basic system feature, as far as I know.
Best regards,
Uli
Maajelvv said:
Hey Kuzibri, You are absoluteley right. I get no connection true active sync or anything. I'm pretty sure there's something really wrong here. never had this problem before. btw I've mistaken with
my spl version. it's the one Sir Sternas recommended. Spl 1.66 HSPL.
I'm Really confused right now. and Pissed off at the same time...
I mean I loved my HD2 with Artemis Rom close to beeing perfect.( installed Igo8 witch right before I went on holliday, stopped working but mannaged to get TomTom navi to work ) then suddenly my answer button stopped working. so I figured let's install a new Version of Artemis rom. I backed up all my files using microsoft my phone. then used task29. done. So I tried to get to the bootloader.... Nothing. tried attatching it to the pc and hoping it would start if I pressed the custom rom .exe (Read somewhere id might work) Nothing not even a blank screen for startup. now I've got nothing else I can think of. please, U guys have given me so much good suggestions.
Thank you all for your time and your efforts to help me solve this issue.
Maajelvv
Click to expand...
Click to collapse
Hi,
I have send you a PM. Please read this ASAP!!
regards, Kuzibri
Hey Uli,
I've tried both. with and without sim or SD cards. still no functioning....
I've thought about the fact that it might be broken but it worked right before flashing....
thanks for your efforts though..
Maajelvv
As I already mentioned, this poor guy has a major problem with his device, which seems to be hardware related (either volume down button does not work or the on/off key). After having extensive contact with him by phone, the only solution seems to be to bring it back to the store to let it repair. Unfortunately, he will have a great chance to loose his warranty, because HTC probably will be able to found that there is another ROM installed. Whish Maarten good luck with his problem!! Also very sorry I could not help you to solve your problem. I'm personally very disappointed by that!
regards, Kuzibri
Hey, i tried to install android on my HD2 several times and failed, but then i noticed i had wrong version of hspl so i couldn't start MAGLRD (i had 3.03 i think i should've had 2.08 right?) Anyway i then tried to remove the HSPL by formatting my sd card and putting the file from original rom (i don't remember the name) and renaming it to LEOIMG, it started installing the rom i went to another room, when i came back it had finished and was on the red/blue/green screen and it said update failed and i had to retry, but now none of the exes work like rom updates or task29 nothing. when i turn on the phone it says "Not allow" and then goes to the red/blue/green screen. Please help me, I'm freaking out is there any way to fix it? Is there even a way to access SD card when the phone does this?
TomaToz, use the computer to flash via USB cable.
I can't, none of the rom updates or ANYTHING works since this, they all give errors
go to the magLDR page and look for how to remove it.
then start from scratch
There's no info how to remove it but even if there was how would i? None of the exes work and i can't turn the phone on, also i dont think MAGLRD got installed cause i had HSPL 3.03 instead of 2.08
Come on isn't htere anyone who ca help me? :|
are you sure you haven't bricked your phone?
because it just seems you did :/
I don't think you read the bold "You need HardSPL 2.08 before installation!" just above the history?
anyway, can you not flash a radio via USB as well?
also, if you post the error messages you get maybe we can help you more.
you can also check here:
http://forum.xda-developers.com/showthread.php?p=10275463
What does bricked mean? :9
and no i can not flash radio or anything else, i'll edit this message with a picture of what the error message looks like
EDIT: WOW, i tried to run the hspl installation and installed hspl 2.08 successfully, not i turned my phone on and its the screen where you choose to start the update for rom. This is the update after which my hd2 said "Update failed" so I'm scared to take any steps, please respond and tell me what to do
HOLY FREAKING CRAP! I installed android and everything seems to work fine, i can't tell you how relieved i am :]]]]
That's for your attention
Does anyone know where to get apps for Android 2.3.2?
What i installed is TyphooN_CM7_v3.5.9-MAGLDR
Help please!!! Hd2 stuck !
HI to all!my phone was working great until i decided to try a new rom so I installed task29 (i had elegancia rom but i wanted to try another rom)and now im stuck on the htc logo screen that says 'stick together' in a red square.....i tried vol down+power button to go into bootloader but nothing happens, then i tried to hard reset but still nothing happens...i pushed the reset button and i did it all over again at least 3 times but still nothing... is there anything else i can try? (even on the hardware?)
my HD2 is a T-MOBILE usa with :
radio 2.08.50.08_2
2.08.HSPL
3.14.531.1 elegancia rom(http://forum.xda-developers.com/showthread.php?t=651729)
i love my hd2 and i want it back...PLEASE HELP!!!!!!!
THANK YOU in advance!!!
sofialoca, task29 is not a thing to be "installed". It's a flash formatting. So you did everything correctly and deleted all from your phone except.. hmmm... stick together.
To flash other rom - just press Volume Down and push reset (under the battery cover) KEEPING VOLUME DOWN PRESSED. Keep it pressed until you are again in bootloader mode. Then connect USB and flash whatever you want.
thank you Andrew!I found the problem...
AndrewSh said:
sofialoca, task29 is not a thing to be "installed". It's a flash formatting. So you did everything correctly and deleted all from your phone except.. hmmm... stick together.
To flash other rom - just press Volume Down and push reset (under the battery cover) KEEPING VOLUME DOWN PRESSED. Keep it pressed until you are again in bootloader mode. Then connect USB and flash whatever you want.
Click to expand...
Click to collapse
thank you so much for the quick response! the problem was with my volume down button...i opened up the phone and moved the flex ribbon a bit to get it into place .after that it got in bootloader mode succesfully!im now back with elegancia and never gonna change it...i think i got a little greedy...afterall elegancia rom is great!thank you Miri and Steve0007 for this great rom and thank you again Andrew!
TomaToz said:
HOLY FREAKING CRAP! I installed android and everything seems to work fine, i can't tell you how relieved i am :]]]]
That's for your attention
Click to expand...
Click to collapse
glad it worked out in the end