Related
I managed to upgrade my phone to aku 3.3 using pof's method(bootloader 1.01 MFG) . Then, out of no where, I tried to use MTTY to upgrade my radio rom
It started as usual with the status bar moving. Suddenly some error messages came up.
Now, the phone is dead completely. I can''t even enter bootloader mode.
Is there a possible way that I can still save it??
Help!!!!
Have I bricked my device? Help plz
I managed to upgrade my phone to aku 3.3 using pof's method(bootloader 1.01 MFG) . Then, out of no where, I tried to use MTTY to upgrade my radio rom
It started as usual with the status bar moving. Suddenly some error messages came up. Can't remember exactly, but like some address can't find error.
Now, the phone is dead completely. I can''t even enter bootloader mode. Only when I take out the battery and plug in the charger cable the red light comes on. I looked the upgrade problem page, my symptom doesn't match any.
Is there a possible way that I can still save it??
Help!!!!
I had something similiar happen a little while back. What I did was pull the battery out and leave it out for a while, maybe a few minutes. I then put the battery back in and held the two side buttons and hit the reset button to put me into bootloader mode. I then cabled it to my computer and flashed a new OS via mutty. That got my phone back and operational.
@float. Nuh, it didn't work on my brick. Prob i will have to take it back to Tmobile if they kind enough to repair the no warranty phone i bought on ebay.
Sorry to have opened a new thread, I was so desperate.
Plz delelte it.
how exactly did you try to update the radio using mtty?
I download the 1.27 shipped radio rom. P.S. It seemed to be a german version, not sure whether that caused the disaster.
Using NBHextract to get the single GSM.NB file, then in MTTY, typed
USB> task 32
USB> lnb GSM.NB
Before flashing, just had it upgraded to the HTC AKU3.3 OS rom only. The old version radio rom version before flashing was 1.18.
Maybe the order i flash is wrong. I flashed OS first then the radio rom.
just guessing
ok, you loaded the radio rom code where os.nb should go. That may have caused mega bad blocks in flash. Can you even get bootloader mode if you reset using Wiki directions to obtain Tri-color bootloader?
Yes. I have tried many ways wiki suggests. Such as removing the battery leaving it more than half an hour and plugging it to the usb cable without battery. still can't get to the tri-color bootloader mode. Basically, I just can't turn on the phone.
If you connect it to the computer, can it communicate w/the PC? If you hear the windows tones try opening up mtty and see if you can communicate.
i'm stuck in the same place
for me it happened during extrom flash
Try removing the battery for a bit (a few minutes, maybe half an hour). Then, put the battery back in but don't plug the usb cable in. After that, hold the two side buttons as if you're trying to get it to go into the bootloader. Hit the reset button a few times with your stylus and see if that gets you to the bootloader. That's what worked for me.
tried that
tried removing battery and connecting usb
nothing helps
is there a place that fixes tytn in belgium ?
is there a way to flash a new rom via mutty ?
cause i still have the boot loader, but the phone still in the splash screen
when i type info 2 in the mutty command prompt i get this answer
Cmd>info 2
HTCSQTEK_203”µ·êHTCE
i think it's not realy normal
diffda said:
is there a way to flash a new rom via mutty ?
cause i still have the boot loader, but the phone still in the splash screen
when i type info 2 in the mutty command prompt i get this answer
Cmd>info 2
HTCSQTEK_203”µ·êHTCE
i think it's not realy normal
Click to expand...
Click to collapse
well your not supercid... your still locked to qtek
Look here and unlock your phone before doing any flashing!
http://forum.xda-developers.com/showthread.php?t=295751
to late i ve done that tow day's ago , now the only way to make my phone back to life, PB + KITL method i think
god bless KITL
I tried using the shelltool to flash the faria rom and after the hard reset which was instructed, my phone hangs at the startup screen with IPL _____
SPL____ GSM_____ OS______
(u get which screen)
i dont think it charges because when i connect it to the charger, the light doesnt light up
help...please!!
if your confident that you have plenty of charge in your device then just enter boot loader mode and reflash your carriers rom or wizard love rom. If you dont understand then tell me and i'll explain the process in more detail.
yay i fixed the problem
it seems that holding the camera button to go to bootloader mode didnt work
so i only tried the other one and WALLAHH
bwesty said:
if your confident that you have plenty of charge in your device then just enter boot loader mode and reflash your carriers rom or wizard love rom. If you dont understand then tell me and i'll explain the process in more detail.
Click to expand...
Click to collapse
thanx for the response anyways
i for some reason got an error 300 when using the love rom using the official orange rom does not work since it tries to upgrade with an older version. This is not possible.
now the phone is stuck at the login screen with the ipl spl gsm and os numbers.
i can get into bootloader mode but after installing a new image with the bootloader (not the love or operator version) i return to this screen.
used another installer with the same rom and it worked. yeah, now retry again and follow the instruction
If anyone can help me I just brick my ameo. I download olipro unlocker followed steps had everything done but after i finished the 1step it wont boot up again its just dead. tried hard reset alot of times wont even go pass it . it just light green.Pls help
Can you enter the Bootloader mode?
Press Camera Button (completely) and hit the reset button at the same time.
i know yor problem press cambutton and powerbutton for at same time so you will come to the bootloader modus now plug in your usb cabel to your device and your computer now open the image of wm6 that you want to install the setup will find your ameo now
hope you will get it
good luck from germany and sorry my bad englisch
Thank you that Fixed it. I just panic but now the whole process was finished. from 1-3 now. thank you for the reply
please help.
I have the same probleme and i can´t enter the Bootloader mode.
remove sim and storage card then do as mosho said
ie press camera, comms button and reset button then restore original rom , then olipros program
as per the wiki
http://wiki.xda-developers.com/index.php?pagename=Athena_Resets
cant get into bootloader
hello,
i cant get into bootloader at all.
i removed the sim and the memory card, al i get is a short flash of red light t the joystick, and only if the device is connected to the power cable.
it doesnt charge, it does nothing. i tried really everything.
does anybody have an idea?
thanks
mike
try a service exchange at t-mobile. there seems to be something wrong with your device.
my ameo had no probs running olipros unlocker.
regards dieter
i used the unlocker with another ameo i bought, and it worked fine.
so i tried the same with the 2nd, and it crashed.
will they find out that i tried to unlock the device?
regatds
mike
ameo dead
Hi mikekarl
we have the same problem that happened to me today.
i have done it before with another ameo worked fine.
Now i cant get into bootloader or Hardreset.
and i cant try a service exchange because iam not t-mobile customer.
Pls help
I was instaling NBD_v8.3_8MB trough shelltool on my MDA Vario then something happened and my PC restarted I whink it is because of the electicity .... so now when I restardet my phone it is stuck on the T-mobile screen Where it is writen.....
IPL 2.21.001
SPL 2.21.Olip
GSM 02.19.11
OS 6.6.6.666
Thanks in advance
First of all, its not bricked. Bricked = doesn't turn on, nothing, blank screen.
I've looked to your info, you already have HardSPL, so you can flash directly using any RUU, don't use shelltools!
Enter bootloader (hold camera+reset), open up the RUU of the ROM you want (make sure it doesn't have any IPL/SPL) and flash away
well I looked all day what to do and I can not find solution
I just can not understand how to flash the phone
I found one solution via some kind of Wizard_love, but again I do not know what to do
Please help i am haveing the same thing just did it today i have the Cingular 8125....i have held camera+reset and got into these Red,Green,Blue,white screen and it says IPL 2.25 and SPL 2.25 now when i run the ROMUpdateUtility_Wizard_NoID it does not work i have my usb pluged in and my phone says USB please help
Thank you
PS.
I am running Vista
IPL 2.25
SPL 2.25
GSM 02.25.11
OS.6.6.6.666
_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-
Ok i have try everything. I have tried the RUU from the HTC site and even everything else when it is searching for the PDA and crashes idk why. I turn on my phone holding the camera and i get to the Red,Green,Blue,White...Plug the USB in and the phone says USB but not my computer??? so i don't know what i need to do please HELP i just got the phone and read you can do all this stuff
1. Please use a PC with Windows XP
2. Download your original carrier ROM (i.e. Cinglular stock ROM) and flash back to original WM5
3. Install HardSPL or use SSPL
4. Flash to WM6
starkwong said:
1. Please use a PC with Windows XP
2. Download your original carrier ROM (i.e. Cinglular stock ROM) and flash back to original WM5
3. Install HardSPL or use SSPL
4. Flash to WM6
Click to expand...
Click to collapse
Were can i get HardSPL,SSPLand the flash back up?
all i have is the original rom
You guys wanna see bricked? I have a BRICKED! phone... My MDA was the unfortunate victim of a car accident. When my car went carreening off the road, my MDA went flying through the air and ended up on the floor of the car but not before hitting virtually every surface on the inside of the car.
Now my charge port is completely snapped off and my battery shorted out when I was trying to hold the charge port in place to charge it and fried the main board. DEAD. NO MORE.
THAT MY FRIENDS, IS BRICKED....
No worries though, I already ordered a TyTN II
Cool can you help?
Oh and i had the same problem with my mda and i got it replaced from tmobile. - the easiest way to reapair an MDA is getting it replaced ^^
offtopic
@dharvey4651
Why didn't you buckle up your phone?
Well i got mine up and running agian just used XP and install the RUU from HTC YES.......Now when i go to install WM6 when i press update were it should show me the Ver. of the one i am installing on my phone it does not say why please help and what do i need to install WM6 on my phone?
Just a quick question did you read the other threads there are already. They basicly explain everything clear and good
i have just still stuck on some stuff
dferreira said:
First of all, its not bricked. Bricked = doesn't turn on, nothing, blank screen.
I've looked to your info, you already have HardSPL, so you can flash directly using any RUU, don't use shelltools!
Enter bootloader (hold camera+reset), open up the RUU of the ROM you want (make sure it doesn't have any IPL/SPL) and flash away
Click to expand...
Click to collapse
jukata
first of all,as dferreira has assured u that ur device is not bricked,secondly ,you already have HardSPL,that means your device is unlocked,just follow his instructions,download any wm6 Rom and flash,it'll good to go,but if u still want to be sure,download WST Tool from the below given thread read carefully and apply the tool to verify the status of ur device,
http://forum.xda-developers.com/showthread.php?t=329170
u can flash NBD rom which u have or any other wm6 rom,goodluck
NVM i am on the Other Page! Thanks
Ok, i have read everywhere and can't help myself, so if someone would be kind enough to help it would be much appreciated
Ok, Used SoftSPL and tried flashing the ROM. It manages to get to 99% and then just goes RED. I have tried 3 different ROMS and same story it goes RED at 99%.
When i remove the battery, it goes to the RUU Red, Green and Blue screen. SPL version is 2.16.0001. Not Oli's new one.
What do i do from now?
kastro said:
Ok, i have read everywhere and can't help myself, so if someone would be kind enough to help it would be much appreciated
Ok, Used SoftSPL and tried flashing the ROM. It manages to get to 99% and then just goes RED. I have tried 3 different ROMS and same story it goes RED at 99%.
When i remove the battery, it goes to the RUU Red, Green and Blue screen. SPL version is 2.16.0001. Not Oli's new one.
What do i do from now?
Click to expand...
Click to collapse
Soft SPL only allows you ONE update, so phone is CID unlocked only when Soft SPL is loaded.
It's normal for the RUU to stick on 99 % for a couple of minutes, The whole update will take aprox 10 minutes.
You can try the hard SPL from there you are semi-permanently CID unlocked.
Good luck,
EquinoXe
I try to put AP DUAL 3.0 ROM on my AMEO with sim unlock.
Probably was CID locked, and so it was impossible to install this ROM, but here what happened....
When The Firmware Flasher rebooted the device at the first step when i pressed UPGRADE BUTTON my ATHENA died... no power at all..
I think at this passage the flashing process was not started at all, infact i did not see the tre coloured bar of the bootloader... IT DIED !!
It is impossible to power on, i try to plug the AC and no orange light...i i pull of the battery and insert the AC plug the red light is OK.....
What happens ?
Is there a way to recover my NEW DEVICE ?
Thanks to all the team !!!
gab74 said:
I try to put AP DUAL 3.0 ROM on my AMEO with sim unlock.
Probably was CID locked, and so it was impossible to install this ROM, but here what happened....
When The Firmware Flasher rebooted the device at the first step when i pressed UPGRADE BUTTON my ATHENA died... no power at all..
I think at this passage the flashing process was not started at all, infact i did not see the tre coloured bar of the bootloader... IT DIED !!
It is impossible to power on, i try to plug the AC and no orange light...i i pull of the battery and insert the AC plug the red light is OK.....
What happens ?
Is there a way to recover my NEW DEVICE ?
Thanks to all the team !!!
Click to expand...
Click to collapse
So did it start step 1 at all? Did u try a soft reset on the device to see if that would boot it back up?
Try running the unlocker anyway. You might be surprised
Olipro does excellent work. [tease]Or at least he didn't disappoint in the past![/tease]
See also http://forum.xda-developers.com/showthread.php?t=357142
See if you can get to the bootloader, what happened was that you used an older version and I'm assuming you got the x7501 which almost always is bricked when used with the older version of oli unlocker. I don't understand why they can't remove or re-label that old package, what's wrong with doing it???? Maybe less people would brick their device.
i've AMEO T-MOBILE X7500
The operating system was WINDOWS MOBILE 6
I did not use oil unlocker... i only try to flash with the ROM i say before, and my AMEO stops working before starting the flashing process.
Now my athena is died: without the battery i try to connect to ac cable and the red led lights up....when i insert the battery the red led lights off, i cannot enter into the bootloader because the ameo doesnt power on at all...
Please is there any solutions to this problem ??? It is very strange that the AMEO stop working ....before starting the flash process... infact when i push the UPGRADE button of the ROM flashing program, the ameo rebooted and died before starting the flashing process > i.e before the three coloured bars of the bootloader starts...
Any help : sorry for my bad english, i'm italian......
is there a way to power on ameo without battery ???
Just try oli's unlocker!
Sorry, but do i use the unlocker even if the PDA is died ? If i plug into the PC USB no hardware is found ? Does the unlocker work ? And please : Where can i download the last version of the unlocker ( probably a stupid question...)
yes, try the unlocker anyways. Download it from the http://forum.xda-developers.com/showthread.php?t=315831
Ok but the unlocker told me : Athena must be connceted with activesync...mine is died..only red led without battery or no led with battery inserted.....so i do not understand how the unlocker could work..... What unlocker do i download ???
In fact.. i try a nothing... the unlocker works only if the athena is recognized...so only if it is power up....but mine is dead only red led without battery....no led with battery instead...
It seems impossible that a simple flashing destroy the unit !!!!
Can you enter bootloader? Hold camera button while resetting
Or hard reset? Volume down wile poking the reset hole.
no, no bootloader, no hard reset...
nothing....
OK I contact HTC the told me to send the PDA to T-MOBILE CENTER to be repaired in warranty....but i leave in italy so i cannot send the pda in england...
i sell it on ebay is someone is interested...serach HTC ATHENA XT7500 AMEO T-MOBILE on ebay.co.uk.....
OK - I just had the same problem. No life whatsoever.
Simple solution:
Remove battery.
Wait one hour.
Replace battery.
All is fine
No need to send back to HTC
hello i´m from spain and I am new to the forum and I need help urgente.creo which is the best forum in which there pdas.the same that gab74.the pda is death or die.I do not know how I can rekindle my pda.Does nothing and htc have told me the same thing, besides not covered by the warranty.Help the PDA is new.
oscmae said:
hello i´m from spain and I am new to the forum and I need help urgente.creo which is the best forum in which there pdas.the same that gab74.the pda is death or die.I do not know how I can rekindle my pda.Does nothing and htc have told me the same thing, besides not covered by the warranty.Help the PDA is new.
Click to expand...
Click to collapse
I just told you the answer in my last post! Why do you have to ask again?
Hi all,
I got the same problem & I already did as Confucious's guide but it doesn't work. Any help?
Best regard,
Try my thread, I am having similar difficulties, though I know some solutions, so maybe some of your questions will be answered.. http://forum.xda-developers.com/showthread.php?t=528258
And in summary.. try jump-starting the battery, I'm almost sure it will help