If anyone can help me I just brick my ameo. I download olipro unlocker followed steps had everything done but after i finished the 1step it wont boot up again its just dead. tried hard reset alot of times wont even go pass it . it just light green.Pls help
Can you enter the Bootloader mode?
Press Camera Button (completely) and hit the reset button at the same time.
i know yor problem press cambutton and powerbutton for at same time so you will come to the bootloader modus now plug in your usb cabel to your device and your computer now open the image of wm6 that you want to install the setup will find your ameo now
hope you will get it
good luck from germany and sorry my bad englisch
Thank you that Fixed it. I just panic but now the whole process was finished. from 1-3 now. thank you for the reply
please help.
I have the same probleme and i can´t enter the Bootloader mode.
remove sim and storage card then do as mosho said
ie press camera, comms button and reset button then restore original rom , then olipros program
as per the wiki
http://wiki.xda-developers.com/index.php?pagename=Athena_Resets
cant get into bootloader
hello,
i cant get into bootloader at all.
i removed the sim and the memory card, al i get is a short flash of red light t the joystick, and only if the device is connected to the power cable.
it doesnt charge, it does nothing. i tried really everything.
does anybody have an idea?
thanks
mike
try a service exchange at t-mobile. there seems to be something wrong with your device.
my ameo had no probs running olipros unlocker.
regards dieter
i used the unlocker with another ameo i bought, and it worked fine.
so i tried the same with the 2nd, and it crashed.
will they find out that i tried to unlock the device?
regatds
mike
ameo dead
Hi mikekarl
we have the same problem that happened to me today.
i have done it before with another ameo worked fine.
Now i cant get into bootloader or Hardreset.
and i cant try a service exchange because iam not t-mobile customer.
Pls help
Related
Hi all,
Hope I may be of help to those who have GSM Error on their Wallabys. I have almost given up hope but I just searched the threads. This is basically what I did:
1. Download xda developers special rom and re-flash via sd card
2. Hard reset, press contact and calendar buttons (or a combination of both), volume button, and soft reset will bring you to the today homescreen (I cant remember exactly what buttons I pressed, I just pressed them all)
3. Re-boot phone, you will notice you still have no radio but you can now enter today homescreen (please take note the "start" menu is not there)
4. Align screen / stylus. You can do this by pressing Action Key then Calendar button.
5. Press Contact and Action Key (both) several times (I think around 20 times). You will hear clicking sound. This will bring out the "start" drop down menu. If it does not pop out, repeat again.
6. Download the correct RSU for your phone. Save into SD and copy to programs (same procedure as in wiki)
7. Run the RSU program, expect to fail at 1%. Re-boot. this time you will be able to active sync your phone again. (my wallaby did to my surprise)
8. I gave up on the RSU 4.16 (after countless tries) and I downloaded RSU 4.21 from xda-developers ftp (exe file) since I am now able to sync to my device.
9. Install RSU upgrade to your device, the phone will automatically re-boot.
10. Surprise! I was able to re-flash the RSU! (I think the problem is the RSU 4.16, try other 4.xx instead but be careful to use the correct version)
Now my Wallaby is up and running again! Thanks to xda-developers and Wiki and to Lumpi. There is no secret. I just did a lot of reading from the threads. It's all there. Good luck guys! Merry Christmas!
why ur wallaby resynched....
The reason it re-synched.... is because... when u go to the wallaby bootloader... and go into the GSM menu's (that allow u to tun off and on the gsm... and band tests... the key to it is there.... just reset those puppies at least 1nce.. then when u reset and boot... voila... it will sync,, but... I'm still stuck on that 1% error... rsu failed!! so.. wish me luck... oh.. btw.. when u get the 1% error it will not sync again until u repeat the process at the wallaby bootloader... so... any ideas anyone>> to get past the 1% error? I've read up and down ... searched left and right here... but no luck yet... I'm still trying what was posted here... so... wish me luck.... !!! oh... question what version is ur wallaby?? PW10A or B?
Re: why ur wallaby resynched....
r5pete said:
The reason it re-synched.... is because... when u go to the wallaby bootloader... and go into the GSM menu's (that allow u to tun off and on the gsm... and band tests... the key to it is there.... just reset those puppies at least 1nce.. then when u reset and boot... voila... it will sync,, but... I'm still stuck on that 1% error... rsu failed!! so.. wish me luck... oh.. btw.. when u get the 1% error it will not sync again until u repeat the process at the wallaby bootloader... so... any ideas anyone>> to get past the 1% error? I've read up and down ... searched left and right here... but no luck yet... I'm still trying what was posted here... so... wish me luck.... !!! oh... question what version is ur wallaby?? PW10A or B?
Click to expand...
Click to collapse
hello..
did you find a solution for 1% error? I have the same issue and I tried all night...and day...and nothing (
Reflash via SD
Hi morph751,
Firstly, thanks for this, I have now finally got my Wallaby back to a state where I can ActiveSync it, and actually run programs on the thing. Unfortunately, the RSUupgrade continually faults at the 1% mark both version 4.16 and version 4.21. The one step in your instructions that I did not follow, was the first "Download xda developers special rom and re-flash via sd card". The problem with doing this, is that when cold booting with the SD card in the slot the device simply hangs at the GSM Error screen. I have bootloader version 6.22, so I assumed this was due to the post 5.17 SD card locking. But the info and utility to bypass this doesn't seem to help either.
Is there something fundamental I am missing in terms of being able to boot the device into a mode that will allow me to flash it via SD?
By the way, when trying to flash the device via Program A, it fails with an error indicating that the power cable is not plugged into the device. The device is in the cradle, with USB connected and power connected to cradle.
OK, by folllowing the instructions at http://forum.xda-developers.com/showthread.php?t=245282, I have been able to sucessfully flash the device to XDA Developers special ROM image 1.2. But I still get Program B failing at 1%, using version 4.21. Has anyone managed to overcome this, if so how? Thanks in advance for any help.
Hi guys, I have some experience with rom flashing, and I did it today as usual - flashed HTC 1.35 ... Update stopped at 1%. I tried everything I could to finish the update (It wasn't my first time ). Now, after restart TyTn is flashing with LCD (black & white) & camera led. I can't do anything, even turn it off. Seems like a problem with bootloader. What should I try before i send it for repairing? Do you have any experience with T-Mobile UK? I'm the legal owner of PDA, but I don't have any receipt. Should I contact seller (ebayer) or post it to T-Mob straight away?
Thanks in advance, Jack.
Anyone please?
Check out the wiki for Tytn upgrade problems
I also had this problem, upgrade stopped at 1%....Left it for an hour and no progress. Had to stop update, which then left me at the boot loader screen (tri-color) screen. Tried Hard reset as mentioned above, no luck, still stuck in boot loader, tried to reload rom..got error 262 upgrade error
I had just run the unlocker and set device to super CID, and thought maybe that was my problem, but it wasn't
Luckily the wiki had the answer
Problem 4: Device is stuck in bootloader mode (tri-color screen)
>Disable ActiveSync: connections -- settings -- uncheck "Allow USB Connections"
Remove the battery, put it back in, connect the USB cable, power on the unit (this should allow the USB port to be opened again)
Wait a minute or two, if you get a message that device cannot be recognized just close and ignore it
Open
mtty.exe and select "USB" from the dialog box, then hit Ok.
You should see a white screen, hit enter and you should see a prompt like this: "USB>"
Type set 14 0 (do not copy and paste!!!) and hit enter
Soft reset with stylus
OS ROM and radio version should be back and OS functional, the unit isn't a BRICK anymore!
I had to reload the rom. step 8 did nothing, but return me to bootloader. This time the rom upgrade took about 45 minutes to complete. Weird, but it worked...This is first time in at least 4 rom upgrades with this device and at least 50 other rom upgrades that I ever encountered any issues.
POF...Thanks for the great wiki
http://wiki.xda-developers.com/index...ame=HTC_Hermes
Unfortunately, when it hanged on 1% connection was totally lost. Everytime I tried to run rom upgrade/unlocker/spl downgrader is said no connection. Now I don't have bootloader screen, only flashing LCD & camera diode. Any suggestions?
If you can't get the bootloader running then a service center will be the only solution I think.
Has anybody found the solution to this problem, my phone is doing the same thing. Can't get it into bootloader and screen & camera flash just blinks? I tried everything but to no avail.
Hi mate, have you done anything special or it goes bricked "without help"? I I still haven't put it to RMA because there's no T-Mobile in Republic of Ireland and I'm 2 lazy to go to Belfast
jackass_ass said:
Hi mate, have you done anything special or it goes bricked "without help"? I I still haven't put it to RMA because there's no T-Mobile in Republic of Ireland and I'm 2 lazy to go to Belfast
Click to expand...
Click to collapse
It's bricked trying to update it!!! If i could just get it to the bootloader, i can probably revive it but can't do anything. Can't access USB or nothing, I'll guess I'll send it off to a repair center.
Are there any good repair centers in the US???
Three days back,my SPV C550 suddenly hanged.I restart it by removing the battery.After reboot, it now only showing desktop with battery icon,signal strength indicator and the Unlock button(soft key) with Windows Mobile screen logo.I tried Hard reset, which cannot complete succeessfully.It also can't connect to Active Sync.
I also tried to flash the ROM from SD card,but it can't allow update because
my phone doesn't have a SuperCID.i unable to change CID because both SPV-Services and pdocread.exe need Active Sync connetion to work.
I searched all the forums,but didn't find any solution how to change CID without Active Sync.
Please help.
I had a similar problem with mine. The screen is the same as yours only varying with the sim card removed to a sim missing logo. Also mine makes the error/message noise repeatedly for a phew secoonds every half hour or so.
I just gave up in the end and admitted it was a brick
and the saga continues
Well the TyTn has died and I'm still waiting on a refund on a dodge wizard so its time to dig out the old SPVs I have a working Tornado (the right soft key has packed up thats a little annoying) so am trying to revive this hurricane.
I have linked some pictures of what is dose display and as you can see it will load into boot loader but due to not being ably to unlock it I cant flash any of the roms I have found.
I have been trying to fix this now for well bloody ages on and off but a good straight 12 hours just recently and to no avail.
In short I need a way to unlock the phone without active sync. The only way I can think of being able to do this is with some kind of specific software through boot loader
Any ideas?
HELP PLZ DEAD SPV c550 During WM6 Upgrade
i hv made a mistake while upgrading my spv c550(HTC Hurricane) to wm6.
i have flashed the wrong spl SPL 1.01.0109 on my fone. that spl was of htc typhoon.
now my phone is not booting up.
when i press the power button the fone gives the white disply and nothing else happens.
i cannot even get into bootloader.
the charging function works when the fone is turned off.
when i turn on the fone it dos nothing not even chaging.
is there any way to get my old fone back...
help plz
i shall be very thankfull to you.
I try to put AP DUAL 3.0 ROM on my AMEO with sim unlock.
Probably was CID locked, and so it was impossible to install this ROM, but here what happened....
When The Firmware Flasher rebooted the device at the first step when i pressed UPGRADE BUTTON my ATHENA died... no power at all..
I think at this passage the flashing process was not started at all, infact i did not see the tre coloured bar of the bootloader... IT DIED !!
It is impossible to power on, i try to plug the AC and no orange light...i i pull of the battery and insert the AC plug the red light is OK.....
What happens ?
Is there a way to recover my NEW DEVICE ?
Thanks to all the team !!!
gab74 said:
I try to put AP DUAL 3.0 ROM on my AMEO with sim unlock.
Probably was CID locked, and so it was impossible to install this ROM, but here what happened....
When The Firmware Flasher rebooted the device at the first step when i pressed UPGRADE BUTTON my ATHENA died... no power at all..
I think at this passage the flashing process was not started at all, infact i did not see the tre coloured bar of the bootloader... IT DIED !!
It is impossible to power on, i try to plug the AC and no orange light...i i pull of the battery and insert the AC plug the red light is OK.....
What happens ?
Is there a way to recover my NEW DEVICE ?
Thanks to all the team !!!
Click to expand...
Click to collapse
So did it start step 1 at all? Did u try a soft reset on the device to see if that would boot it back up?
Try running the unlocker anyway. You might be surprised
Olipro does excellent work. [tease]Or at least he didn't disappoint in the past![/tease]
See also http://forum.xda-developers.com/showthread.php?t=357142
See if you can get to the bootloader, what happened was that you used an older version and I'm assuming you got the x7501 which almost always is bricked when used with the older version of oli unlocker. I don't understand why they can't remove or re-label that old package, what's wrong with doing it???? Maybe less people would brick their device.
i've AMEO T-MOBILE X7500
The operating system was WINDOWS MOBILE 6
I did not use oil unlocker... i only try to flash with the ROM i say before, and my AMEO stops working before starting the flashing process.
Now my athena is died: without the battery i try to connect to ac cable and the red led lights up....when i insert the battery the red led lights off, i cannot enter into the bootloader because the ameo doesnt power on at all...
Please is there any solutions to this problem ??? It is very strange that the AMEO stop working ....before starting the flash process... infact when i push the UPGRADE button of the ROM flashing program, the ameo rebooted and died before starting the flashing process > i.e before the three coloured bars of the bootloader starts...
Any help : sorry for my bad english, i'm italian......
is there a way to power on ameo without battery ???
Just try oli's unlocker!
Sorry, but do i use the unlocker even if the PDA is died ? If i plug into the PC USB no hardware is found ? Does the unlocker work ? And please : Where can i download the last version of the unlocker ( probably a stupid question...)
yes, try the unlocker anyways. Download it from the http://forum.xda-developers.com/showthread.php?t=315831
Ok but the unlocker told me : Athena must be connceted with activesync...mine is died..only red led without battery or no led with battery inserted.....so i do not understand how the unlocker could work..... What unlocker do i download ???
In fact.. i try a nothing... the unlocker works only if the athena is recognized...so only if it is power up....but mine is dead only red led without battery....no led with battery instead...
It seems impossible that a simple flashing destroy the unit !!!!
Can you enter bootloader? Hold camera button while resetting
Or hard reset? Volume down wile poking the reset hole.
no, no bootloader, no hard reset...
nothing....
OK I contact HTC the told me to send the PDA to T-MOBILE CENTER to be repaired in warranty....but i leave in italy so i cannot send the pda in england...
i sell it on ebay is someone is interested...serach HTC ATHENA XT7500 AMEO T-MOBILE on ebay.co.uk.....
OK - I just had the same problem. No life whatsoever.
Simple solution:
Remove battery.
Wait one hour.
Replace battery.
All is fine
No need to send back to HTC
hello i´m from spain and I am new to the forum and I need help urgente.creo which is the best forum in which there pdas.the same that gab74.the pda is death or die.I do not know how I can rekindle my pda.Does nothing and htc have told me the same thing, besides not covered by the warranty.Help the PDA is new.
oscmae said:
hello i´m from spain and I am new to the forum and I need help urgente.creo which is the best forum in which there pdas.the same that gab74.the pda is death or die.I do not know how I can rekindle my pda.Does nothing and htc have told me the same thing, besides not covered by the warranty.Help the PDA is new.
Click to expand...
Click to collapse
I just told you the answer in my last post! Why do you have to ask again?
Hi all,
I got the same problem & I already did as Confucious's guide but it doesn't work. Any help?
Best regard,
Try my thread, I am having similar difficulties, though I know some solutions, so maybe some of your questions will be answered.. http://forum.xda-developers.com/showthread.php?t=528258
And in summary.. try jump-starting the battery, I'm almost sure it will help
Hello All
my work has 100 mda vario's
but they all had windows mobile 5.1 on it
so i say to my boss i can flash it to windows mobile 6 with htc touchflo
he liked it so he let me do it
but it goes wrong
the mda vario does nothing anymore
just a bootloader cames up with : red green,blue,white
saying :
ipl 2.21.0001
spl 2.21.001
my idea is to get a working rom on a mini sd card and flash it from the sd card
but how to let the sd card starts load and let it flash,
not one button works in the bootloader
i have tried a lot of tricks i also have one time get restore to factory defaults.
but wont work, it says format completed, so no error's
thats good i think
but i really need to fix it.
otherwise my boss wont be happy
also active sync wont work anymore , the pc wont see the phone all .exe updates ultilty gives me errors that they dont get response from the phone
that comes because it only stays in the bootloader and the bootloaders has left under a usb sign, there stood usb
can this be fixed?
any help plz
Regards
R.G
hi there... 2 bad is the boss phone!!!
hi there... 2 bad is the boss phone!!!
first of all, try a hard reset, then plug once again the phone to PC
dont worry, activesync wont recognize phone at all (is just usb connection)
tell me if hard reset worked, and ill keep in touch
i kpnw there is a tool that would help you to fix the phone.... first try the hard reset!
Good luck
I got the same problem, the hard reset works, but the problem is there yet.
Ich hab das gleiche Problem, der Hard reset funktioniert, das Problem besteht jedoch weiterhin
Hello All
Thanks for u responses i like that
okay hard reset works
but nothing has changed by that
hard reset is the question with restore to factory defaults?
and than i get a screen with format complete.
Regards
R.G
hello All
i fixed it
i know get a green screen with ipl,spl, os
but everything is terrible slow
really slow i mean when i press start it takes a minute to show up
why is this?
plz help
i fixed it with abort all processes in task manager and use wizard love rom.
this is the only possible way i think
regards
R.G
R.G
You know what you did,whats wrong with the phone,you flashed a wm6 rom to a CID locked device.A CID locked phone cannot be upgraded to wm6,you must have a CID unlocked device for upgrading to wm6.
Now,as its a G4 device,it cannot be CID unlocked,but,however,it can be upgraded to wm6 through either SoftSPL or HardSPL method.
Now first recover back to its default status by downloading official stock rom and flash it,after it starts to work normal,then follow the SoftSPL or HardSPL method,only then it'll upgrade.