Three days back,my SPV C550 suddenly hanged.I restart it by removing the battery.After reboot, it now only showing desktop with battery icon,signal strength indicator and the Unlock button(soft key) with Windows Mobile screen logo.I tried Hard reset, which cannot complete succeessfully.It also can't connect to Active Sync.
I also tried to flash the ROM from SD card,but it can't allow update because
my phone doesn't have a SuperCID.i unable to change CID because both SPV-Services and pdocread.exe need Active Sync connetion to work.
I searched all the forums,but didn't find any solution how to change CID without Active Sync.
Please help.
I had a similar problem with mine. The screen is the same as yours only varying with the sim card removed to a sim missing logo. Also mine makes the error/message noise repeatedly for a phew secoonds every half hour or so.
I just gave up in the end and admitted it was a brick
and the saga continues
Well the TyTn has died and I'm still waiting on a refund on a dodge wizard so its time to dig out the old SPVs I have a working Tornado (the right soft key has packed up thats a little annoying) so am trying to revive this hurricane.
I have linked some pictures of what is dose display and as you can see it will load into boot loader but due to not being ably to unlock it I cant flash any of the roms I have found.
I have been trying to fix this now for well bloody ages on and off but a good straight 12 hours just recently and to no avail.
In short I need a way to unlock the phone without active sync. The only way I can think of being able to do this is with some kind of specific software through boot loader
Any ideas?
HELP PLZ DEAD SPV c550 During WM6 Upgrade
i hv made a mistake while upgrading my spv c550(HTC Hurricane) to wm6.
i have flashed the wrong spl SPL 1.01.0109 on my fone. that spl was of htc typhoon.
now my phone is not booting up.
when i press the power button the fone gives the white disply and nothing else happens.
i cannot even get into bootloader.
the charging function works when the fone is turned off.
when i turn on the fone it dos nothing not even chaging.
is there any way to get my old fone back...
help plz
i shall be very thankfull to you.
Related
I managed to upgrade my phone to aku 3.3 using pof's method(bootloader 1.01 MFG) . Then, out of no where, I tried to use MTTY to upgrade my radio rom
It started as usual with the status bar moving. Suddenly some error messages came up.
Now, the phone is dead completely. I can''t even enter bootloader mode.
Is there a possible way that I can still save it??
Help!!!!
Have I bricked my device? Help plz
I managed to upgrade my phone to aku 3.3 using pof's method(bootloader 1.01 MFG) . Then, out of no where, I tried to use MTTY to upgrade my radio rom
It started as usual with the status bar moving. Suddenly some error messages came up. Can't remember exactly, but like some address can't find error.
Now, the phone is dead completely. I can''t even enter bootloader mode. Only when I take out the battery and plug in the charger cable the red light comes on. I looked the upgrade problem page, my symptom doesn't match any.
Is there a possible way that I can still save it??
Help!!!!
I had something similiar happen a little while back. What I did was pull the battery out and leave it out for a while, maybe a few minutes. I then put the battery back in and held the two side buttons and hit the reset button to put me into bootloader mode. I then cabled it to my computer and flashed a new OS via mutty. That got my phone back and operational.
@float. Nuh, it didn't work on my brick. Prob i will have to take it back to Tmobile if they kind enough to repair the no warranty phone i bought on ebay.
Sorry to have opened a new thread, I was so desperate.
Plz delelte it.
how exactly did you try to update the radio using mtty?
I download the 1.27 shipped radio rom. P.S. It seemed to be a german version, not sure whether that caused the disaster.
Using NBHextract to get the single GSM.NB file, then in MTTY, typed
USB> task 32
USB> lnb GSM.NB
Before flashing, just had it upgraded to the HTC AKU3.3 OS rom only. The old version radio rom version before flashing was 1.18.
Maybe the order i flash is wrong. I flashed OS first then the radio rom.
just guessing
ok, you loaded the radio rom code where os.nb should go. That may have caused mega bad blocks in flash. Can you even get bootloader mode if you reset using Wiki directions to obtain Tri-color bootloader?
Yes. I have tried many ways wiki suggests. Such as removing the battery leaving it more than half an hour and plugging it to the usb cable without battery. still can't get to the tri-color bootloader mode. Basically, I just can't turn on the phone.
If you connect it to the computer, can it communicate w/the PC? If you hear the windows tones try opening up mtty and see if you can communicate.
i'm stuck in the same place
for me it happened during extrom flash
Try removing the battery for a bit (a few minutes, maybe half an hour). Then, put the battery back in but don't plug the usb cable in. After that, hold the two side buttons as if you're trying to get it to go into the bootloader. Hit the reset button a few times with your stylus and see if that gets you to the bootloader. That's what worked for me.
tried that
tried removing battery and connecting usb
nothing helps
is there a place that fixes tytn in belgium ?
is there a way to flash a new rom via mutty ?
cause i still have the boot loader, but the phone still in the splash screen
when i type info 2 in the mutty command prompt i get this answer
Cmd>info 2
HTCSQTEK_203”µ·êHTCE
i think it's not realy normal
diffda said:
is there a way to flash a new rom via mutty ?
cause i still have the boot loader, but the phone still in the splash screen
when i type info 2 in the mutty command prompt i get this answer
Cmd>info 2
HTCSQTEK_203”µ·êHTCE
i think it's not realy normal
Click to expand...
Click to collapse
well your not supercid... your still locked to qtek
Look here and unlock your phone before doing any flashing!
http://forum.xda-developers.com/showthread.php?t=295751
to late i ve done that tow day's ago , now the only way to make my phone back to life, PB + KITL method i think
god bless KITL
I was trying to upgrade to radio v1.43 in the hope that battery life was improved over 1.41 however when it got to 8% it stopped and gave me an error i can't remember After atempting to recover, it got off the three colour screen now the 3100 stalls on the blackshadow version4 screen (bootloader screen?) and goes no further. I tried reflashing but got a 260 and using mtty, only getting 2 com port options, didn't offer any help.
I'm really sorry to have not been able to sort this with reading through the relevant post but I haven't found a solution. What else can I try?
Hi,
Could you pls advise what is your device made, model, SPL version ... etc.
Also did you try to do Hard reset?
I'm using now black MAJIK (and few days ago black shadow) with radio 1.43 with no problem.
its the SPV m3100 When I decided to go Black shadow I read up on mr vanx and made sure I had all the things I needed. If I remember right, when I came to upgrade to Majik the auto detect found the second option down
SPL-1.04/1.10 - 1.09 Bootloader. I've realized since I had a spaz and ran the RUU from the archive this time. From what I've since read thats not too cleaver.
I have tried a hard reset and took the battery out instead of pressing space.
I dont know if this information on the starter screen is of use
M 05
S 04
B 05 D 3lak
I'm not sure, but hard reset doesnt mean you take the batery out.
Please check that link:
http://wiki.xda-developers.com/index.php?pagename=Hermes_For_Beginners#hardreset
I was in your position (hanged on booting) few days ago, and when i did hard reset, it changes every thing to basic normal condition.
i meant when i did a hard reset when it asked me to press space to reboot I took the battery out. I tried again this time pressing space to reboot but I still get stuck on the loading screen. I can't connect by USB to the PC I'm guessing the drivers on the phone haven't loaded and I'm stuck as to what to do.
Does anyone have any ideas?
try look at it http://forum.xda-developers.com/showthread.php?t=286755
ok I've tried everything I can think of to connect the 3100 to the computer so I can reflash it but mtty gives only com 1 and com2 but no USB and neither those two work, active sync wont connect so I disabled it as suggested and running the radio ruu and wrapper wont querry the device. I am now at a loss as to what to do next someone must know what I should do. Please?
what is your SPL?
try this http://wiki.xda-developers.com/index.php?pagename=HTC_Hermes
sl is 1.09 i'd updated it on the previously successful black shadow flash
msn [email protected]
icq 150277111
AIM TazmanFH9
Yahoo bigfathairyboggart
I have tried changing KITL trasport but I am unable to select or chose either option. I have also tried the rversion command in the tri colour screen but nothing happens. I hope I'm missing something nice and simple but I get the feeling I'm not going to be that lucky. Please help
tcSPVm3100 said:
sl is 1.09 i'd updated it on the previously successful black shadow flash
Click to expand...
Click to collapse
I suggest you check again, press and hold the side OK button and the power button...then put the stylus into the hole in the bottom of the unit.
yeah I've done that it's "SPL-1.09"
I had this exact problem yesterday, with the same bootloader too. The phone would not pass the splash and IT refused to upgrade. I ended up downgrading to a shipped wm5 rom (in my case the cingular 1.30.502.1_1.11.00.00) which to my surprise actually worked as no rom radio or spl upgrade moved at al on my phone. Then upgraded back to black majik. I hope this helps.
Thanks. I downloaded the trial of wm5 from the windows website and it asked me to install .NET framework version 1 so I got that but it turns out to be 2.0 not 1.1 It would say it had repaired but it would say this with or without the phone connected.
tcSPVm3100 said:
Thanks. I downloaded the trial of wm5 from the windows website and it asked me to install .NET framework version 1 so I got that but it turns out to be 2.0 not 1.1 It would say it had repaired but it would say this with or without the phone connected.
Click to expand...
Click to collapse
Just download a WM5 ROM from the wiki page!
ok tried this too no luck.
Trying to use the one from orange (linked to through wikki) I get an 294 invalid vendor error however active sync cannot connect yet of course so is this to be expected?
I have however gotten a connection with mtty which is a step forward dunno what to do with it yet though except trying the password 0000000000000000 command but it not disabling the password. This then lead me to read for a further hour how to change it and I've got to be honest; it beat me. I have No idea what the hell its talking about. My head hurt with so much reading.
I get a no gsm pop up v briefly on loader. I so want my phone back
I have since tried CID unlocker just so i get something installed onto this brick but I either get a connection error or it telling me it can't install for some other reason. I can not set the password in mtty to 0000000000000000 so how do I do that and is this the first step to getting things sorted? "just running a rom install" is not happening I can get a USB connection in mtty and that is it. Is the fact i'm running SPL 1.09 a problem? I'm getting precious little help guys If i'm posting in the wrong place or something please let me know. I need thing thing back now. Hours are drifting by with me trying to get some head knowledge but I still need some guidance please
tcSPVm3100 said:
I have since tried CID unlocker just so i get something installed onto this brick but I either get a connection error or it telling me it can't install for some other reason. I can not set the password in mtty to 0000000000000000 so how do I do that and is this the first step to getting things sorted? "just running a rom install" is not happening I can get a USB connection in mtty and that is it. Is the fact i'm running SPL 1.09 a problem? I'm getting precious little help guys If i'm posting in the wrong place or something please let me know. I need thing thing back now. Hours are drifting by with me trying to get some head knowledge but I still need some guidance please
Click to expand...
Click to collapse
can u flashing HARD V7?,i think better u have IPL 1.04 SPL 2.10olipro first ,then try to flashing radio?
and did u try SD card.
In bootloader can anyone here connect with active sync? I can't so updating rom and radio flashes in the usual way isn't possible. Trying the hard spl again it tells me to make sure active sync is connected and as it isn't it throws back a 262 update error. 0% on the hermes and that's currently as far as I can get. I have no means with which to access the memory card.
The reason you get an invalid vendor ID is because your CID doesnt match....download a ROM which is for your device (an orange one?)...then try.
You need to read the wiki alot more before trying anything else since you are not aware of the vendor ID error...nor the fact you MUST use HardSPL.
I linked to the orange ROM from wikki and tried installing it. it was while installing THIS ROM SPV_M3100_ROMUpdate_0407.exe I got invalid vendor error.
Installing a recent DL on HARD spl v7 I get a 240 open file error that's one I haven't had before.
With all other attempts they all say they want an active sync connection.
I can not connect to the phone through active sync
so all attempts by me to flash anything to the phone using an RUU fails.
If anyone can help me I just brick my ameo. I download olipro unlocker followed steps had everything done but after i finished the 1step it wont boot up again its just dead. tried hard reset alot of times wont even go pass it . it just light green.Pls help
Can you enter the Bootloader mode?
Press Camera Button (completely) and hit the reset button at the same time.
i know yor problem press cambutton and powerbutton for at same time so you will come to the bootloader modus now plug in your usb cabel to your device and your computer now open the image of wm6 that you want to install the setup will find your ameo now
hope you will get it
good luck from germany and sorry my bad englisch
Thank you that Fixed it. I just panic but now the whole process was finished. from 1-3 now. thank you for the reply
please help.
I have the same probleme and i can´t enter the Bootloader mode.
remove sim and storage card then do as mosho said
ie press camera, comms button and reset button then restore original rom , then olipros program
as per the wiki
http://wiki.xda-developers.com/index.php?pagename=Athena_Resets
cant get into bootloader
hello,
i cant get into bootloader at all.
i removed the sim and the memory card, al i get is a short flash of red light t the joystick, and only if the device is connected to the power cable.
it doesnt charge, it does nothing. i tried really everything.
does anybody have an idea?
thanks
mike
try a service exchange at t-mobile. there seems to be something wrong with your device.
my ameo had no probs running olipros unlocker.
regards dieter
i used the unlocker with another ameo i bought, and it worked fine.
so i tried the same with the 2nd, and it crashed.
will they find out that i tried to unlock the device?
regatds
mike
ameo dead
Hi mikekarl
we have the same problem that happened to me today.
i have done it before with another ameo worked fine.
Now i cant get into bootloader or Hardreset.
and i cant try a service exchange because iam not t-mobile customer.
Pls help
Hi all, first of all I am no geek, I would like to unlock my HTC TYTN so that I may use other sims while abroad etc. I have read the instructions, downloaded v£a of the Sim Cid unlocker, however every time I run the unlocker my phone shuts down and reboots. I have tried with the phone without sim with none network sim with Orange sim same result phone shutys down and reboots. I have tried waiting till it is connected via active sync after rebooting but it nust keeps rebooting. I have even manually loaded the hard spl and run it on the phone but my phone shuts reboots and the spl has not been updated. Can anyone tell me what I am doing wrong?.
Thanks in advance Jimmy
info on device status tytn on orange
I have kept trying but still the phone keeps rebooting everytime I try to unlock. Device status uis as follows
operator version 24.181.1.612
ROM version 1.81.61.2 WWE
ROM Date 09/20/07
Radio version 1.27.12.29
Protocol version 22.45.88.07W
does any of this indicate I would have a problem using current unlock version 3a?.
Thanks in advance Jimmy
Check to see if the SPL has changed... Go to bootloader - hold power, OK above flywheel and reset with stylus. hold until tri-colour screen comes up. It will tell you your IPL and SPL.
It may already have flashed and that means you can update your rom with more safety.
Do you get any errors when running the pc? For instance [error 260](pretty common).
If that error keeps coming up you need to COMPLETELY remove activesync and then reload. All sync relationships MUST be deleted too. That fixed mine
Cheers...
Hello Everybody,
My mobile at&t 8525 alias HTC 8525 is stuck in windows operator logo.It would not boot further. It happened while I tried to upgrade it from Windows 5.0 to Windows 6.0.First I got a tri-colour screen,but in a hurry I tried to backgrade to windows 5.0 again.
Other problem the mobile cannot be synced. I have installed Microsoft Active sync 4.5. Even then it could not be synced.
I tried to read all the posts ,but could not understand anything.
So please help me in getting my mobile repaired
Don't worie.
I had somewhat the same issue with a bad ROM flash.
Just disconnect the USB and boot to the bootloader screen (the tricolour screen) and you should be able to reflash the phone again.
Problem in syncing the mobile
I am not able to sync the mobile to the laptop.I have installed Microsoft Active sync 4.5. Even then it is not syncing.So how could I run the hermes upgrade if the mobile is not helping.
Please help
In Activesync on PC - Untick "Allow USB Connections".
Put the Hermes into bootloader (tri-colour screen) and connect by usb. Run the RUU_Wrapper.exe file you want. Follow onscreen instructions.
You need to have installed Hard SPL V7 for this to work...
did not work
Hello Boss
I tried to follow the procedure you suggested me. but it did not work. I tried with Hard SPl 7.0.
Please give me some suggestion
you dont need an active sync connection to flash it. Enter bootloader(tri colour screen) as you were told in the previous posts and Just click on the boxes that you do have a connection(even though you dont) and then flash the rom.
@ultramag69 i hve never had to untick allow usb connections and i have cocked up loads of rom flashes, saying that i have never had a problem flashing in vista either so maybe i am lucky
If you still cant flash doing it this way, then maybe you should try flashing from sd card instead, just make sure the battery is fully charged. Full instructions of how to do this are found in the hermes wiki, which i advise you to read anyway.
Oh and good luck anyway, you should be able to recover the phone from this ,so i wouldnt fret too much
Guess he isnt hardspl'ed... then his batt is death... must to flash a shipped rom.
correct me if im wrong.
Problem with upgrade At&T 8525 mobile
Hi!
I'm having problems with my Cingular 8525, after I made the upgrade to WM6.1 (FARIA-R32-XDA2_WM6.1.rar) for WM 6.5 (FCWs_stock_like_6.5_v3.rar), and slowed my device does not work anymore. He died.
I need help please. How resurrect it?
Excuse my English.
english is not the problem here cause we need more info... device info SPL IPL hardSPL? you go from 6.5 to 6.1?
Do you try to flash first the Stripped?
Does your batt has charge enough to boot?
There are many many things to say so... start to tell us all your history!
Hi
I tried to Hard spl with Hard Splv7. But I got a error. I even tried the Sd Card method.Its says loading and I get the tricolour mode. If I press the Power button its not showing the status of upgradation.
Where can I get a shipped rom. Actually my Spl is 1.11.
Hi
I tried to Hard spl with Hard Splv7. But I got a error. I even tried the Sd Card method.Its says loading and I get the tricolour mode. If I press the Power button its not showing the status of upgradation.
Where can I get a shipped rom. Actually my Spl is 1.11.
check the wiki pages for your device in the upper bar of this web forums
there are many official roms.
I also am currently using an 8525 (Herm100). It was received from an Ebay deal with WM5. I flashed it with the ATT OEM WM6pro (aka shipped wm6). Once it hit the three color boot screen, it sat on that for a couple of minutes then started cooking. Once it showed a progress bar, it took about 3 minutes to cook the WM6 over the WM5. It also showed a popup that stated going back to WM5 was not an option.
I would suggest running the installer again and going down to 7-11 for a refreshment. You may not have let it percolate long enough to set itself up for the actual ROM overwriting.
gorkalraghavendra said:
Hello Everybody,
My mobile at&t 8525 alias HTC 8525 is stuck in windows operator logo.It would not boot further. It happened while I tried to upgrade it from Windows 5.0 to Windows 6.0.First I got a tri-colour screen,but in a hurry I tried to backgrade to windows 5.0 again.
Other problem the mobile cannot be synced. I have installed Microsoft Active sync 4.5. Even then it could not be synced.
I tried to read all the posts ,but could not understand anything.
So please help me in getting my mobile repaired
Click to expand...
Click to collapse