Hey Guys,
after a while without flashing i want to flash the new Shamanix Rom.
So i loaded it, started the application, but after i press "auto detect" on the Bootloader Selection it says "Unknown Version".
So i went to Mrvanx Guide:
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=30&Itemid=27
and tried to flash HardSPL.
The strange thing is, that the flash went through in about 1 second.
The Status Bar was 0 and jumped up to 100 Percent.
This is why i think it didn't work, but if go into the bootloader mode it shows "SPL 2.10 olipro"
After that i tried again to flash Shamanix Rom and selected Bootloader 1.10 manually. The devices goes into bootloader-mode, but instead of starting to flash i get the Error "260 - Couldn't connect to device"
Can Somebody give me a hint please?
raix said:
Hey Guys,
after a while without flashing i want to flash the new Shamanix Rom.
So i loaded it, started the application, but after i press "auto detect" on the Bootloader Selection it says "Unknown Version".
So i went to Mrvanx Guide:
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=30&Itemid=27
and tried to flash HardSPL.
The strange thing is, that the flash went through in about 1 second.
The Status Bar was 0 and jumped up to 100 Percent.
This is why i think it didn't work, but if go into the bootloader mode it shows "SPL 2.10 olipro"
After that i tried again to flash Shamanix Rom and selected Bootloader 1.10 manually. The devices goes into bootloader-mode, but instead of starting to flash i get the Error "260 - Couldn't connect to device"
Can Somebody give me a hint please?
Click to expand...
Click to collapse
WHY.....would you select bootloader 1.10??? Your bootloader version is 2.10.olipro.
Errr, you can come over and slap me right in the face for this stupidity.
I really don't know what i was "thinking". After selecting Bootloader 2.10 it flashed without Problems.
we all have our moments...............but need to be a wee bit careful with these devices....they can become very can·tan·ker·ous !
hermes un bricking
HI
I am new in this game
how i can select manualy the Bootloader?
thanks
press and hold the button on the left side next to the scroll wheel and the power button on the right side at the same time....while holding the buttons down insert the stylus into the soft reboot hole on the bottom of the phone.........continue holding the buttons for a second or two after releasing the reset button at the bottom.
hermes unbricking
thanks
spl 1.04
ipl 1.01
bricked hermes aftert unversal simunlocker v1
stuck on windows screen.
allredy try the method from the wiki with mtty.
do i have any othe option?
thanks
Related
i can't do kitl mode, after presing com + power +ok buton nothing happen, also com + power + reset, it just reset the unit, can someone help, thanks
AFAIK not all roms have KITL enabled.
Okay a dumb question since I couldn't find the info from the forums.. What is this KITL and since it's not enabled in all ROMs, are there a way to enable it or are there any original shipped roms with this KITL enabled?
I think i've a serious problem.
My Tytn has been stuck in tri-colored boot screen and shows
Herm200
IPL-1.04
Herm200
SPL-2.03
I've looked at the wiki and found this
http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
because of SPL 2.03 i should try this
http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
But when i try to come in PB_KITL_MODE nothing happens.
i guess the comm-manager key is the middle key on the right side.
Any ideas what i could do ?
Thanks for your help
CGill
cgill said:
...
But when i try to come in PB_KITL_MODE nothing happens.
i guess the comm-manager key is the middle key on the right side.
...
Click to expand...
Click to collapse
Yes, this is the comm-manager key, but I think you are just here:
pof said:
AFAIK not all roms have KITL enabled.
Click to expand...
Click to collapse
So i guess there is really no other way than to send the device to the repair center ... :-(
I only wanted to update to the WM6 official firmware. I will phone with the repair center tomorrow morning and here what they will say.
If anyone else has any idea what i could to to unbrick my device i would appriciate any help. But i think all what i could try has already be done.
I also have a SPL-2.03 Bricked Hermes... but I cannot get to the KITL mode, nothing happens and I stil lget the tri-color screen.. is there any updates on how to get to KITL, or how to unbrick without getting to KITL? And by the way, what KILT stands for?? Thanks
and by the way, when I try to get to KITL pressing the suggested buttons I get a flash of a white screen saying "no image file" it´s just a flash, then it gets to the tri-color screen. It seems to recognize the USB, as when I connect the phone, it says USB underneath the PDA screen... Pls Help!
I had the same problem a few months ago. My lil sis cell (TyTn aka 8525) just crashed on her and when I got it to do a soft reset it, booted up to the tricolor. Here's what i did:
1. Disable ActiveSync: connections -- settings -- uncheck "Allow USB Connections"
2. Remove the battery, put it back in, connect the USB cable, power on the unit (this should allow the USB port to be opened again)
3. Wait a minute or two, if you get a message that device cannot be recognized just close and ignore it
4. Open mtty.exe and select "USB" from the dialog box, then hit Ok.
5. You should see a white screen, hit enter and you should see a prompt like this: "USB>" (for some reason, I got Cmd>)
6. Type set 14 0 (do not copy and paste!!!) and hit enter
7. Soft reset with stylus
8. OS ROM and radio version should be back and OS functional, the unit isn't a BRICK anymore! (after the "set 16 0" I got it to boot but "No GSM" cell is non-functional but PDA functions work)
9. if it doesn't unbrick, repeat all the steps but with the command set 16 0
Source link: http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems#problem4 will allow you to download the mtty.exe
Hope this helps.
i have an ameo and it went dead. i can get it in the bootscreen or connect with usb. how can i get to the usb bootscreen. hard reset doesnt work then it says press action to restore factory default. but it doesnt do anything. i just want to get the rainbow screen with usb, just sop i can connect with sync or something else
please help me
Allready tried to put out your micro SD? And thenn do a reset?
Does your computer recognise your device when you plug it in?
What does the bootloader say your SPL is?
If the answer to the first question is yes then you should be able to flash one of the WM6 ROMS onto your device regardless of activesync. If your bootloader says you have Olipro's SPL then you can flash ANY ROM. Only found this out yesterday. If your device is a different spl then you'll have to install one which matches your CID.
Ameo Fix
Hold the Camera and Comm Manager button and press reset to load into Bootloader, then install ROM image
05mehmet said:
Hold the Camera and Comm Manager button and press reset to load into Bootloader, then install ROM image
Click to expand...
Click to collapse
make it and flashing sopp bei 1 %
ERROR(294): INVALID SELLER -ID
felix999
ATHE100
AOL-v1.00
ATHE100
SPL-v1.10.RP00
I have WM5.0
runing AthenaUnlocker
STEP1>>>all OK
STEP2>>>stop by 60 % and now can do nothing
only have bootloader and now corect rom...
please help???
felix999
I need to upgrade the SPL on my SPV C550 now that I have unlocked it (trying to install WM6)
Do I have to buy a mini SD card reader or can I use tools to do this from my PC.
If so which tools please and briefly how.
Cheers
John
john72821 said:
I need to upgrade the SPL on my SPV C550 now that I have unlocked it (trying to install WM6)
Do I have to buy a mini SD card reader or can I use tools to do this from my PC.
If so which tools please and briefly how.
Cheers
John
Click to expand...
Click to collapse
Although a search would solve your problem here is a mini how to:
- you need to have ParchedRUU (this includes these files: EnterBootLoader.exe, Patched_RUU.exe, ROMUpdateUtility.exe, RUUGetInfo.exe and finaly your_bootloader_name.nbf) all in the same directory. The files are availabe on the net just google it.
- establish an activesync connection with USB, to do so have the phone in standby mode (no bootloader mode)
- when connected in activesync (green icon on taskbar) run the Patched_RUU.exe
- make sure you tick the boxes and the next button and that phone battery is greater than 50%
- in the final screen hit the update button, if the .nbf is in the same directory as the Patched_RUU it will load it automatically
- wait for 3 minutes, during this time you phone will enter bootloader mode, and a red bar will show the progress on the phone and the computer
you are all done
- mike
Cheers mate that did the job.
Next I guess I get into boot loader mode and then use mmty.exe?
Any clues please on how to get into boot loader mode.
john72821 said:
Cheers mate that did the job.
Next I guess I get into boot loader mode and then use mmty.exe?
Any clues please on how to get into boot loader mode.
Click to expand...
Click to collapse
again search m8!
anw here it goes:
- go to active sync -> settngs -> disable USB connections
- switch off your phone, and while holding the camera button connect it to the USB, on the screen it will appear "Need UI upgrade? (0)" or something like that.. bottom line is press 0
- then phone enters bootloader mode. if on the lower bar i think it is the green bar it says hurricane and on the right UI then it is all good, if it says something like XIP or something then you have to switch it off and do the proccess from the begining with the camera button REMEMBER TO PRESS THE 0
- fire up the mtty.exe, remember put mtty.exe AND the bin in the C:\ directory. The only thing you need to change in the startup screen of mtty is the connection port change from com1 or something to usb and press ok
- press enter so the Cmd> shows on the blank terminal
- write without quotes "l c:\name_of_your_rom.bin" and hit enter. l is a small L short for load
- hopefully it will do the update, wait for ~10 mins and it will say that it is all done... depending on your rom you may have to change language and so...
hope this helped
- mike
Sorry to carry on a bit but I get this when I do what you suggested.
Cmd>l C:\wm6.bin
clean up the image temp buffer at 0x8C080000 Length 0x01C40000
MTTYDownloadImageNot allow operation!
Error : DownloadImage return error (code = 0xFFFFFFFF)
Ive Googled this and im sure ive unlocked my phone - but is that the same as unlocking the super CID?
i dont remember man, are we allowed to post links to other sites? anw follow this guy's tutorial it is allmost the same
http://karhoe.byethost33.com/content/view/35/1/
- mike
help..
need to flash phone from boot loader mode..no standby mode..how do i do that???
HELP!!!!!!!!!!!
Just follow my guide in the signature, but use huricane ROM instead, you need to get into the bootloader and enable AS USB mode, then run the RUU
i hv made a mistake while upgrading my spv c550(HTC Hurricane) to wm6.
i have flashed the wrong spl SPL 1.01.0109 on my fone. that spl was of htc typhoon.
now my phone is not booting up.
when i press the power button the fone gives the white disply and nothing else happens.
i cannot even get into bootloader.
the charging function works when the fone is turned off.
when i turn on the fone it dos nothing not even chaging.
is there any way to get my old fone back...
help plz
i shall be very thankfull to you.
DEAD SPV
i hv made a mistake while upgrading my spv c550(HTC Hurricane) to wm6.
i have flashed the wrong spl SPL 1.01.0109 on my fone. that spl was of htc typhoon.
now my phone is not booting up.
when i press the power button the fone gives the white disply and nothing else happens.
i cannot even get into bootloader.
the charging function works when the fone is turned off.
when i turn on the fone it dos nothing not even chaging.
is there any way to get my old fone back...
help plz
i shall be very thankfull to you.
Where I can find the latest SPL for C550?
I hate to say this but after flashing I got stuck and can't get past the 2nd splash screen.
Anyone got any ideas?
I'm Supercid and Unlocked with
Herm200
IPL - 1.01
SPL - 1.40 Olipro
flashing a WM6 rom
which rom were you flashing?
Have you tried re-flashing an original rom?
if I knew how to boot up I could flash but it stays on the 2nd splash screen so I can't connect via ActivSync and I can't read my SD card.
Just thinking now, if I can get a card reader, couldn't I do the 'Herming' thing?
allan1 said:
if I knew how to boot up I could flash but it stays on the 2nd splash screen so I can't connect via ActivSync and I can't read my SD card.
Just thinking now, if I can get a card reader, couldn't I do the 'Herming' thing?
Click to expand...
Click to collapse
Tried this yet?
Hold the right side power and left side OK buttons in while hitting the reset switch on the bottom. This should put you into the boot loader and you can re-flash from here.
Just put the device to bootloader mode by yourself and reflash a rom. Press at the same time the leftside "ok" button + the rightside "power" button + soft reset with stylus.You should see the tricolor display.Plug cable and run RUUwrapper again.
thanks mate, I forgot all about that
Hi.
Just tryed to inst. Android in my HD2 and now it stuck with a white screen with the HTC logo.
Is it any way to fix this or do i just trach it?
I am not an expert but this happened to me once while installing SD android.
I reinstalled the original ROM from the HTC site and restored my phone to factory settings.
I tried another version of android and it worked well (since last September).
Only observation is that lately (last two month) my phone hangs a lot on both systems (droid & win) and overheats a lot and when this happens I need to wait for it to cool down (at least 20 minutes) then it accepts rebooting (I am stating this although I am not sure is it from the droid or just my HW is faulty for other reasons).
I hope this helps
I tryed a NAND install. Now I cant get conection with usb and computer
Maybe you can perform a hard reset with buttons
1. With the phone turned off, press and hold the VOLUME UP and VOLUME DOWN buttons, then press the END/POWER button shortly and release it.
2. Release the VOLUME UP and VOLUME DOWN buttons.
3. Press the VOLUME UP button to perform the hard reset, or press any other button to cancel the reset.
I hope it works
3mo said:
Maybe you can perform a hard reset with buttons
1. With the phone turned off, press and hold the VOLUME UP and VOLUME DOWN buttons, then press the END/POWER button shortly and release it.
2. Release the VOLUME UP and VOLUME DOWN buttons.
3. Press the VOLUME UP button to perform the hard reset, or press any other button to cancel the reset.
I hope it works
Click to expand...
Click to collapse
didnt work hehe still at the white htc logo screen. I migth installed the files the wrong way round?
Can you get to bootloader (3 coloured screen) by turning on the phone whilst holding vol down?
conantroutman said:
Can you get to bootloader (3 coloured screen) by turning on the phone whilst holding vol down?
Click to expand...
Click to collapse
Yes that's about the only thing i can do
Go-Fast said:
Yes that's about the only thing i can do
Click to expand...
Click to collapse
As long as you can get to bootloader its ok
I would start over from the begining.....
Does it still show that you have HSPL installed on bootloader?
If so, reflash the windows 6.5 ROM that you were using before the android flash.
Then follow the steps in this thread.
Hope that helps....
conantroutman said:
As long as you can get to bootloader its ok
I would start over from the begining.....
Does it still show that you have HSPL installed on bootloader?
If so, reflash the windows 6.5 ROM that you were using before the android flash.
Then follow the steps in this thread.
Hope that helps....
Click to expand...
Click to collapse
Thnx I'll try it later and report back
Still cant get my coputer to connect to the phone.
I get to the "red green and blue" screen, and it says
PB01100 HX-BC
SPL-2.00.HSPL 8G XE
0x85
CotullaHSPL 0x40
I'm on win7 SP1
Ok when you enter bootloader (red green blue screen) you should see "Serial" at the bottom..
When you connect to the computer it should change to "USB"
You might not see anything happen on your computer but the word at the bottom of the bootloader should change.
I might be mistaken here but Im pretty sure you need "2.08 HSPL" although your bootloader shows you have HSPL installed its not 2.08. This might be the cause of your original problem.
Once it says "USB" your ready to flash a ROM via USB as usual...
If it stays on "Serial" after a few minutes then try another USB port or computer if possible.
Enter bootloader and run the HSPL tool and choose 2.08HSPL......
Then start the process from the beggining.
Hope that helps.
conantroutman said:
Ok when you enter bootloader (red green blue screen) you should see "Serial" at the bottom..
When you connect to the computer it should change to "USB"
You might not see anything happen on your computer but the word at the bottom of the bootloader should change.
I might be mistaken here but Im pretty sure you need "2.08 HSPL" although your bootloader shows you have HSPL installed its not 2.08. This might be the cause of your original problem.
Once it says "USB" your ready to flash a ROM via USB as usual...
If it stays on "Serial" after a few minutes then try another USB port or computer if possible.
Enter bootloader and run the HSPL tool and choose 2.08HSPL......
Then start the process from the beggining.
Hope that helps.
Click to expand...
Click to collapse
Hah your a babe conantroutman lol thnx
Is this the rigth SPL ?
Not to intrude on conantroutman here but yes you have to have HSPL 2.08 and a 2.15.50.14 or 2.10.50.02 radio for MAGLDR to work. Without the HSPL 2.08 you can not flash MAGLDR and without the proper radio version MAGLDR will not even boot up.
So to answer your question yes the HSPL you have in the picture you posted is the correct HSPL.
Yep as T said, hspl is good, radio is good. Your all set.
That guide for installing android at the top of the thread is pretty damn good and will have you up and running in no time. Let us know how you get on
Sent From My Fingers To Your Face.....
thnx to both of you. I'll post here when done
Crap my call button dont work when I'm in bootloader
When your in the MAGLDR menu?
You may have to flash WM again to test the call button. Or try reflashing MAGLDR, that may help...
Sent From My Fingers To Your Face.....
I guesse it's a lost case so I just installed winmo and runing android from SD card
thnx for the help.
btw!
is there a way to get htc sense to work on a huawei u8800 or x5?
Hmmm its very weird because if your call button works in WM then it should work in MAGLDR....