Hi ,
During the replacement of broken housing, two of phone parts fell out. I don't know where to return them (please find attached photos).
Maybe it is something with speaker, because silent icon is always displyed when I turn device on.
Please advice.
Related
Hello gurus,
I have spent a few hours first looking around in the wiki for help. None found yet. Please diagnose and help me get my display working so it does not fade when I release finger pressure from the tmobile logo area. To operate the unit constant pressure need be applied to that spot for the display to bleed through. Otherwise it fades to white. Please advise. Thanks. G
I have the same problem, I have to keep it squeezed on the left hand side.. I read a thread about it before and everyone was saying that its a loose/crap connection for the screen..
It sounds like a loose connection in your upper slide. I would recommend finding locating the Wizard Service Manual and following it to dis-assemble your device and "tighten" up that loose connection.
KEEP IN MIND TAKING APART YOUR DEVICE WILL VOID YOUR WARRANTY
If you find that it is not a loose connection and that there may be a more serious issue, then I recommend sending your device back to HTC to have it repaired.
EDIT:: Found it:
http://forum.xda-developers.com/showthread.php?t=333715&highlight=wizard+service+manual
It's for sure a connector problem. This happened to me 3 months ago. I dropped the phone and it went white. so i dissembled the phone and the film connector that is used to connect the mainboard with the screen was loosen. i put the connector back in place and everything was ok.
My streak was cracked when I accidentally sat on it. So I ordered one from ebay and replaced a new screen on it. After replacing the new screen, my streak only showed blank screen when I turned it on. I don't know if during the process of disassebling I did something wrong or not. But I did actually redo all the steps but the problem still occured. If anyone can give me any direction to see what wrong with my phone. I am really appreciate that.
Bengo..... My 2-cents is: Assuming you got all cables & connectors re-assembled correctly, you either have a defective replacement screen/digitizer or when you accidently sat on it you may have broken more than just the screen (cracked main board or similar). I would start with trying another replacement screen...
Sent from my Dell Streak using xda premium
Did you switch it on with the broken screen? Did the display work partly?
If it did, atleast we know that the assembly may have caused the problem.
You might want to check the connectors again. See if they are secure and if the little brown clips have actually secured the tan coloured wires. Make sure they are down and fastened. The wire with the serial number and the bar code on it is the one responsible for the display. so make sure thats secure.
Also, if you dont already, try to test if it works before you put the screws back on. Just put the plastic parts back together and test. If it doesnt check connectors again.
In any case, if you decide to re-order a new screen, the connectors would come with it (except the small one for audio). SO you can take time fiddling with the other three connectors.
Best of luck!!
Did you solve this? I had the exact same problem after dropping mine, changed display and then always blank screen. If you have any info I'd appreciate it!!
This is the 2nd digitizer I've broken on this phone. I took it off and replaced it. I put it back together and the digitizer did not work. I checked the connections and even took the digitizer off. I put the old, cracked but working, digitizer on and it no longer worked. I took the phone apart again and put the new digitizer on and it still did not work. Considering the old digitizer suddenly did not work, it must have been something I did to one of the boards or connectors on the phone. Also, the speaker no longer works. Any thoughts or suggestions on where I went wrong?
I can't guess what's the problem exactly but I can give you a few tips.
dissasmeble the phone according to the vidoes you can find on the web.
when you assemble it don't attach the digitizer to the screen yet. connect the digitizer first to the phone. then put the screen in place, with the digitizer still connected but not on the screen.
in this way you can test the phone before "closing" it.
A week ago, I dropped my Note 2 on the sidewalk and smashed the screen (the phone itself functioned, but the screen was blank)
I took it to a local, reputable repair shop for fixing, and received the phone today, with a working screen.
I realized upon arriving home that both the Wifi and Bluetooth functions will not turn on.
They both do the following:
They will be grayed out, then allow you to turn on after about six seconds
When I press to turn on, it sits in the "on" position for five seconds, then slides back to the "off" position
After perusing the forums, I have done the following to try and determine the problem.
1) Took the battery out to restart the phone
2) Factory reset and flashed back to stock (had been on Jelly Beans)
3) I opened up the casing to see if any hardware had been dislodged that I could see (not an expert eye, mind you...I consider myself more of a tinkerer (I have been kicking myself for shelling out the dough for the repairs when the screen replacement looks so fun...)
Attached is a pic of what I think I should be looking at, after watching a few disassembly videos: (red rectangles).
--Note that the other side of the casing (which has what looks like tape over what is the wifi antenna(?) is not damaged as far as I can tell.
Possible explanations? Was the antenna damaged when the phone fell (face down)? Was damage done during screen replacement?
Thanks for reading! And apologies that my first post, after lurking for a while now, is a "take" post rather than a "give" one!
update? did you fix it?
I have the same problem (not working Wi-Fi - Bluetooth)
hello, this it's the first time i write an entry in a forum, but i have a problem with my s2, the problem it's that i buyed sometime ago a screen replacement for my phone because i accidentally broke the lcd, and when it arrived, i changed it because i have some experience with this phone because i have already changed it's screen once, now, while changing the screen, i broked two things, the flex cable of the call speaker and the volume flex that goes onto the motherboard, but with that damaged, my phone turned on once, i didn't see that the volume flex wasn't there so i opened my phone again and now, it doesn't turn on, it's like only the leds of the screen turn on when i touch them, i don't know what to do, i have gone to a mobile center and the guy telled my that to repair that i have to change the flexs i broke, i have changed the call speaker but the volume one it's broken, i just want my phone back.
Sorry for my bad english