Roms restart right after I tap the the Welcome screen - Mogul, XV6800 ROM Development

I got the mogul, and when I run any dcd rom Its loops to the welcome then restarts. Tried relocking, then unlocking (with olp 2.40)
I tried to install the rom first (dcd 2.2.0) then 3.27 Radio(off SD card cause wouldnt reboot)
Then I tried The 3.27 radio first, then 2.2.0 rom same thing(restarts at welcome screen)
SD card flashed back to 2.17 Sprint official, with 1.47 radio(works fine every time)
also tried it on dcd 2.1.0, and 1.6.8 all restarted in a loop,
Anyone have any suggestions on how to fix?
Or does anyone else have a good stable wm6.1 with htc touch UI rom maybe with 3.27 radio included?
I am a noob but im am starting to get this thanks for your help

do you happen to have ftouchflo cooked in somehow? if you have ftouchflo running, it wont let you calibrate the screen (for me at least).

JonnyBoy313 said:
I got the mogul, and when I run any dcd rom Its loops to the welcome then restarts. Tried relocking, then unlocking (with olp 2.40)
I tried to install the rom first (dcd 2.2.0) then 3.27 Radio(off SD card cause wouldnt reboot)
Then I tried The 3.27 radio first, then 2.2.0 rom same thing(restarts at welcome screen)
SD card flashed back to 2.17 Sprint official, with 1.47 radio(works fine every time)
also tried it on dcd 2.1.0, and 1.6.8 all restarted in a loop,
Anyone have any suggestions on how to fix?
Or does anyone else have a good stable wm6.1 with htc touch UI rom maybe with 3.27 radio included?
I am a noob but im am starting to get this thanks for your help
Click to expand...
Click to collapse
The same thing happened to me. The only way that I could get past that issue was to wait about 5 minutes until I started to calibrate the screen. It then worked..... but it would then reboot in a loop when i tried to open Activsync to configure my exchange server. (And no, I didn't have touchflo enabled).
I went back to 3.16 and it works fine.

Make sure your Olipro 2.40 unlocker took correctly. If it did not, then you will get reboots exactly as you described.
Also, did you do a hard reset after installing your latest ROM?

Hard-SPL did not install correctly... This happened to my phone as well.

Rom restarts right after welcome screen
Ill i am about to try that again, but the flash made me lose the ESPT settings.
Now I cant make any calls. I wrote all settings down , but I do not have the Unlock code, And I cant find it, (ITS NOT 000000)Running a mogul.

the reboots are because you didnt unlock correctly.
i had the same problem, i had the new rom flashed but the phone wasnt unlocked right.
you have to run titanunlocker.bat first, follow the instructions then your boot loader should show 2.40.
as for the ESPT settings, you can get the unlock code by using the attached.
your ESN hex is what you need to input to the keygen.
should be under your device information, in your settings.

Roms restart right after I tap the the Welcome
Ok I locked it again, Loaded a fresh official 2.17. Connected to activesync unlocked again, loaded a DCD 2.2.0, then 3.27 radio, restarded,set it all up,
got to page with start tab(home screen) Then starts to restart( at the same point). Maybe I dont Have the right unlocker it says 2.40(when i open with winrar)
Thanks, im very new at this but you guys have help me all the way through.
I have successfully recovered my phone in every way possible. I mean every way. But still havent seen a rom work yet. I feel like IM close though

Roms restart right after I tap the the Welcome
The Spf unlocker that ive been running does not show 2.40 in bootloader after unlock, only 1.10. But when I open it with winrar I can see the olp2.40
should i look for a different one
When I load this spf on phone, from home pc the unlocker says if you see 1.10 unhook usb then reconnect

Roms restart right after I tap the the Welcome
maybe Im not understanding how to do a hard reset a hard reset

thanks for the spc getter worked perfectely

Related

Bricked my phone i think

Hey everyone,
i am so upset and lost; words cannot describe it.
So i installed WM6 black shadow and everything was working except for SMS and MMS. So i am like ok i can live with that for a day till custel' rom will come out. SO i decided to upgrade the radio to 1.43 and boom here is where the problem started, No GSM on boot up. Phone doesn't boot up. I tried install 1.40 over again, still nothing. No i tried upgrade the the rom itself, i tired custel 2.5 and nothing and i tried the new Cingular rom, still same problem. the roms flash all the way. I read the wiki, and saw the mtty.exe thing but that doesn't work for me either. I am really lost and don't know what to do.
Specs
cingular 8525
hardspl v7 cid and sim unlocked.
PLEASE HELP
4.13?? 4.10??
Where did you download these radios from??
or do you mean 1.41 or 1.43??
Yeah thats what i meant, 1.40 and 1.43 sorry. You can see how upset i am.
Thanks Again
Well, if your phone turnes on .. it's not a brick.. lol .. it IS fixable... When you turn the phone on does it go RIGHT to the 3 colored screen?
@dan5.5
You need to read the unbricking thread about this, all the info you need is there.
http://forum.xda-developers.com/showthread.php?t=286755
If you are superCID I don't see how flashing a radio could have messed up your phone.. that's weird.
mrvanx said:
@dan5.5
You need to read the unbricking thread about this, all the info you need is there.
http://forum.xda-developers.com/showthread.php?t=286755
Click to expand...
Click to collapse
I read everything there and nothing seems to be working for me. I woudnt post for nothing. i dont want to be annoying.
OK im going to repost what ive said on 4wm:
We need to check if your Radio BL is functional, firstly leave HardSPL v7 on there and connect to the bootloader via mtty (il assume you know how to do this).
Issue the following commands and tell us the results please:
1) checkimage (this shows the CRC checksums of each component...id expect the radio image to show a timeout....
2) info 2 (This will verify that your CID is intact)
3) info 8 (does a bad block check)
Once youve done this, flash SPL 1.10.oli to the device and once again connect up to mtty.
4) 'rtask a' this will enter the radio bootloader you will see "Enter Radio Bootloader" or something to that effect
from now on when you type the text does NOT appear on the mtty screen.
5) 'rversion' this should return your radio bootloader version...now unfortunatly if you see nothing...you radio BL is dead and sorry your device is royally bricked. If you get something returned back onto the screen (most probably containing the text '0108') then your radio BL is fine.
Click to expand...
Click to collapse
do as instructed in that text, post your results here.
I cant falsh spl 1.10 oli. it gives me the 260 error.
the 260 error is not connected via USB right? .. weird... have you tried taking your battery out for a couple minutes, then booting into BL mode? sounds weird but this worked for me when I didnt flash hardSPL firsl..
hey mrvanx's
I can't downgrade the hardspl to 1.10, anyhelp.
I cant active sync, the phone doesnt boot up.
Is there anyway to aviod having to respond on the phone.
hey,
i can get the phone to boot up into windows and then it freezes within a couple min. what should i do. Still no gsm message and no phone. thanks
Dan
OK, so let's try and get you to a working state - I've bricked mine a couple of times and it can be quite heart-stopping, eh?
The first thing I would do is re-download radio 1.43, just incase your current one is damaged somehow.
Secondly, download Black Shadow - I know it's not the ROM you ultimately want but the aim here is to get you working again and we can move forward from there.
First, boot up into BootLoader mode (hold down the OK button on the left side of the phone and the power button and then press the reset button on the bottom, just in case you didn't know
You should come to the three colour screen and it should be reading IPL-1.04 and SPL-2.10.Olipro. If it isn't, stop here and post what it does say.
If it everything is OK at this point, when you plug your phone into your computer, it should change to USB at the bottom. Just wait for the Found New Hardware prompts to clear on your PC and then flash the black rom - choose the hardspl option in the flash program.
Once that has finished and it is at the "tap screen to set up windows..." bit, put it back into bootloader mode as above and flash the radio.
This should hopefully give you a running phone again as I know this combination works OK as I am currently using it.
Fingers crossed, don't panic, and let us know what the results are
Cheers,
Smiffy.
Nothing is working, can some please help me. Is there anyt way i can restore the spl to the original one so i can send the phone back, i just got it like 2 weeks ago. thanks
Also i have a bad block thats what i think makes the phone freeze after i boot it up.
How can i get around this, thats seems to be the biggest problem.
Hey everyone, let me give you more info.
I can fully flash any rom and and radio,
phone will boot up like 1 out of 10 times and then freezes and thats it.
i have a bad block number 6. I have hard spl v7 installed before the phone got screwed up. I cant downgrader the spl to a lower one to check if radio stack is screwed up. Can someone please help me, if you need to ask me more info feel free.

Bell Mobility HTC6800 + DCD 3.0.0

Can anyone share their experience upgrading their Bell HTC6800 ROM (including radio, unlocking SPL, and upgrading PRL) with DCD 3.0.1? I have never done it before but curious to hear if anyone has had success or failure.
I noticed that DCD released a Bell ROM in his 2.3.2 kitchen but not in his 3.0.0 kitchen. Does anyone know how to port the correct Bell settings into the 3.0.0 release?
My main reason for upgrading is of course better performance but more importantly I am curious about aGPS and how I can use it instead of my Bluetooth GPS receiver. If anyone can share that would be much appreciated.
http://rapidshare.com/files/99219142/DCD_3.0.1_Bell.exe
Check the last page of this thread
http://forum.xda-developers.com/showthread.php?t=363693
Thanks origins81. I noticed now that DCD added the Bell ROM to his 3.0.1. So can you share you experience with this ROM upgrade? Did you have any problems (I assume you've done this before)? Can you share your experience if you are a Bell HTC 6800 user?
1. If you have not already done so, run the 2.40-olipro unlocker. Your device will again be left in tri-color screen.
2. Flash the official sprint 3.35 update.
3. When the device boots for the first time, do not pass screen calibration. Flash a 3.x.x ROM. (that being the custom rom of your choice)
Think I only used the official Bell rom for about a day before i got sick and tired of it and flashed to one of DCD's clean roms, never looked back since then...
As much as I hate Bell, I purchased this phone, had it for about 7 months and got into flashing roms, well, this newest ROM from DCD was the trickiest. First I tried using the Kitchen (disaster), I finally got it to work, installed it, and I kinda forgot to read the instructions, you have to be SURE to install the Olipro 2.40 first, and flash to the new radio, or it will do one of two things. 1st it will either continuously restart or 2nd thing is it will get stuck on the infamous red, blue, and green screen. However if you do get stuck on this, you can flash the rom again, then install the newest radio and it *should work.
But after all that pain and misery, I got a little better signal (I'm not too sure if this is caused by the new rom or not), the GPS works great as always, and seeing as Bell charges 2 arms and your first child for data, I haven't tried the speeds for Rev. A.
P.S- If you ever need help with your Bell 6800, just ask, I've been troubleshooting the same phone for a couple months, and I know how to use a kitchen, just a PM away.
Thanks guys. You have instilled more confidence in me now. I am just going to make sure I have the original stock ROM from ustar as well as the Titan re-locker just in case (I want a backout plan). I will wait a little longer until everyone irons out the kinks of this new 3.35 radio and I will give the latest DCD ROM a try. Thanks again!
I've used the SPRINT update and it works fine. I've added the quick GPS program that comes with the DCD version and I am going to change the startup logos from Sprint to Bell...(As soon as I figure out how). I didn't need to reprogram anything!!
I just got my phone today, gonna give this a shot...
oh man... i ran the olipro 2.4 file and it took me to the tri color mode and then tried to flash it with the latest sprint update. it went up to 4-5% and then it showed an error of Update Utility. i tried to go bak to the Bell update and it did the samething but this time after 1%. can someone please help me out here? I'm with bell.
ok now i'm stuck at the bell screen and at the bottom it says "No Radio" cuz i tried flashing the dcd file.
Well, to begin with, here are the steps I took to accomplish what I have.
1. Flash Olipro 2.40
2. Flash Radio to 3.35 (For the newest version of DCD's rom)
3. Flash the ROM to DCD's rom.
Now, the first time I did this, I got stuck at the tri-color screen, such a pain. I then tried flashing the rom again, and it rebooted continuously and I had no idea why. This was because I didn't flash to the newest radio. So I did that, and it worked, so try those steps, and good luck.
On problem that I did notice is that my phone always has the roaming triangle on?? Hopefully it's not costing me roaming charges... I was going to try and use the DCD 3.0.1 rom but don't want to chance it. I'm going to try playing with it some more an see what happens.
I'm running DCD 3.0.1 on my Bell 6800 and it's working great so far (day 2)
Follow Origins81's install points above, and remain calm if it takes a try or two to get past the 2.40-olipro unlocker 3-color screen step.
I'm having some issues ActiveSync'ing to both work and home PCs, but I don't think it's related to this ROM.
GPS works great with Google Maps
The alarm clock bug is fixed (e.g. not working when plugged in)
Got it working and everyhthing is great except is doesnt play video in the media player...Working on it.
Well for some reason I can't seem to activate my phone. I hit Talk then I enter ##911224#. It tries to connect for 15 secs then hangs up.
I _thought_ I did everything properly.
1) Ran Olipro2.40 (actually it was the unlock from http://www.phonenews.com/how-to-add-gps-to-htc-mogul-xv6800-p4000-titan-2663/) it looks like it's got Olipro2.40 in it.
2) ran official upgrade from sprint (RUU_TITAN_SPRINT_WWE_3.35.651.2_RS_TITAN_3.35.04_4350H_SPCS_AM_Ship.exe)
3) Extracted DCD_3.0.1_Bell.exe and ran the RUU.
hope I didn't perma-brick it.
M
Ok fixed it. Browsed around the and found out in a Howard forum that you have to type ##111111# (doh!) before. Ok my heart can start beating again! Posted for posterity. The code that I used must have been for a different area. This phone is from the GTA.
can you give me a link to those howard forum posts because i ran into a problem ... after a last flash my phone works but its not activated... I tryied ##111111# but i get a code check error... ##911224# doesnt do anything... ##778# works but 000000 code doesnt so i cant get in... HELP
Roaming After Update
After suffering with the pesky Bluetooth issues with my HTC, I thought I'd do some searching on the Internet to see if others had the same issues. Lo and behold, it looks like a real bug with the HTC. After reading some forums, it looked like the latest Sprint release would cure the problem. I downloaded an unlock program ("Hard-SPL-MFG") and the Spring update (RUU_TITAN_SPRINT_WWE_3.35.651.2_RS_TITAN_3.35.04_4350H_SPCS_AM_Ship)
and proceeded to update my HTC.
After a few unsuccessful attempts (stuck at the three color bars a couple of times, restarting a few times on it's own) I managed to get the unlock code and Sprint update installed.
The problem I have now is that it appears that I am now roaming even though I'm in my calling area (I'm with Bell Canada)!
Help! What should I do??
Check the bottom link out, had similar issues when I first flashed. If you have any further questions let me know
http://forum.xda-developers.com/showthread.php?t=363693&highlight=FOR+BELL
i follow the step, but when the phone restart, i stuck a the bell screen...
i'm unable to connect with the usb.
Can you able to help me ? to complete the installation or trying to go back OEM
- i do the first step; see the red, green, blue screen (http://forum.ppcgeeks.com/showthread.php?t=9093)
- flash the rom
- now stuck......
thx for your precious help
TwistedWaffle said:
As much as I hate Bell, I purchased this phone, had it for about 7 months and got into flashing roms, well, this newest ROM from DCD was the trickiest. First I tried using the Kitchen (disaster), I finally got it to work, installed it, and I kinda forgot to read the instructions, you have to be SURE to install the Olipro 2.40 first, and flash to the new radio, or it will do one of two things. 1st it will either continuously restart or 2nd thing is it will get stuck on the infamous red, blue, and green screen. However if you do get stuck on this, you can flash the rom again, then install the newest radio and it *should work.
But after all that pain and misery, I got a little better signal (I'm not too sure if this is caused by the new rom or not), the GPS works great as always, and seeing as Bell charges 2 arms and your first child for data, I haven't tried the speeds for Rev. A.
P.S- If you ever need help with your Bell 6800, just ask, I've been troubleshooting the same phone for a couple months, and I know how to use a kitchen, just a PM away.
Click to expand...
Click to collapse
Hi TwistedWaffle, Are you from the montreal region? I am looking for somebody who would do this stuff for me... Can you help?

reverting to AP3 after failed AP4 upgrade --> customization reset loop

My first attempt to upgrade to AP4 did not succeed unfortunately (SPL to 3.50 upgrade went OK though), my power light stayed green and the display wouldn't come on.
So I took the Athena into bootloader and re-flashed back to AP3.
All seemed fine, the "Tap the screen to set up your device" screen appeared, I set it up and let the customization program run.
Unfortunately after the automatic reset at the end of the customization program, the device returned to the "Tap the screen to set up your device" and the customization program started again...
I tried interrupting the customization by soft resetting before it started executing itself, soft resetted during customization, let customization finish again (and again), but the device seems to be in an endless loop....
Any suggestions/help?
Thanks a lot in advance!
this happen because the spl and the kernel, AKA nk.exe, do not match. not sure what to do except try the new ap3 the cmonex posted **not sure if you tried that**
try the 3.0 cmonex posted and enjoy.
solved!
Thanks irus & Pawel062 (and cmonex!), that did the trick!
Probably not a bad idea to advise anybody who needs downgrading from AP4 to AP3 to use that rom. Download it from http://htc-hackers.com/uploads/ap3newspl.zip
See cmonex' thread at http://forum.xda-developers.com/showthread.php?t=386604
***great Information!***
HEY ALL,
I WAS ALSO HAVING SOME ISSUES VERY SIMILAR TO THESE WHILE TRYING TO "DOWNGRADE" TO ANY ROM FROM AP 4.0. THIS IS GREAT INFO AS I BUILD MY OWN ROMS CONSTANTLY, SO I WAS A BIT WORRIED WHEN I COULDNT SWITCH AFTER TRYING AP 4.O, BUT THANKS TO CMONEX, IRUS, & PAWEL062, WE CAN DOWNGRADE A BIT EASIER!
THANKS AGAIN!
M E G
I downloaded the http://htc-hackers.com/uploads/ap3newspl.zip
can anyone tell me the steps
note i'm stuck into the bootloader
mgozamy said:
I downloaded the http://htc-hackers.com/uploads/ap3newspl.zip
can anyone tell me the steps
note i'm stuck into the bootloader
Click to expand...
Click to collapse
just flash it with normal RUU
I have this problem of the "looping" with the customizations. My problem is that I can't get the device to a state where it is "talking" to activesync and from what I see, I need that to push this ap3spl new file.
When you say "just flash it with normal RUU" can you tell me what that means please? (sorry, noob here...) I've spent hours on the forums, wiki etc and I'm a bit lost.
I'm "trying" to get AP4 w/WM6.1 onto the device.
Purchased unlocked (new) and used on AT&T for 6 months.
Went to update the radio to 1.57 and used the unlocker first. (took out SIM/SD first of course).
Got past step one and then got a black screen on reboot...
I got AP3 to load but now I get this fun looping.. Setup device, load customizations, reboot, and start over.
Sounds like this file in this thread is my fix to at least get AP3 working but not sure how to apply. Can I do it from the bootloader?
thanks in advance for putting up with me
Oh yeah:
My current state:
ATHE100
IPL - v2.02
ATHE100 MFG
SPL -v3.50 OliNex
Eureka!
Ok, I'm not a COMPLETE noob.. (close). I'm up and running. AP3 (new spl) loaded, then loaded AP4. Woo Hoo!
No GPS
Well, I guess I'm "Almost" back up and running.
Since step three never got kicked off, it looks like my GPS rom/radio never was rewritten back to the device.
Any help on how to get just the GPS portion back?
Endless loop after flashing AP4
I have a similar problem. My Dopod U1000 was running WM6 and I upgraded to
radio version 1.58.00 no problem. After flashing AP4 I am in a cycle where my initial boot screen has black and white lines at the top and black at the bottom
Then get the Windows Mobile 6.1 screen and after automatic customizing the
PDA resets itself. I have tried to flash the AP3newspl file but it cant communicate successfully with the synced PDA. Any help?
Johnatara said:
I have a similar problem. My Dopod U1000 was running WM6 and I upgraded to
radio version 1.58.00 no problem. After flashing AP4 I am in a cycle where my initial boot screen has black and white lines at the top and black at the bottom
Then get the Windows Mobile 6.1 screen and after automatic customizing the
PDA resets itself. I have tried to flash the AP3newspl file but it cant communicate successfully with the synced PDA. Any help?
Click to expand...
Click to collapse
get into bootloader by pressing camera+reset and check your spl
you can flash a rom from here
also read this
http://forum.xda-developers.com/showthread.php?t=429013
Thanks lakeman. I reinstalled WM6 ROM from the boot loader.
My IPL v1.00 and SPL v1.20. Olipro and Radio 1.58
I have transferred enblerapi.cab to PDA and run it each time but when I flash
AP4 ROM or AP3newspl ROM I get an endless loop and my SPL stays v1.20
I cant seem to get a flash of SPL3.5 which I suspect is the problem.
Am I missing something?
Il download non funziona.

[Resolved]: Stuck at Bootloader 1.06, titan_exitbl.exe isn't working.

Hi Folks,
I'm stuck in the tri-color screen for bootloader 1.06.
I have DCD 3.2.0 w/3.42.02 radio on the XV6800 and was trying to upgrade to radio 3.42.30. My system is Vista 32-bit.
I ran the Titan Relocker and it put SPL-1.06.0000 back onto the device and was planning on then putting 1.2 onto it.
Running titan_exitbl.exe says "Cannot open USB port. Please make sure, that USB connection in ActiveSync is disabled."
Unfortunately it is now stuck and even after ending the Sync Center service I can't get titan_exitbl.exe to pull it out of the Boot Loader.
Ideas? Thank you!
I could fire up an old XP laptop and try it from there.
Loaded ActiveSync 4.5 on an XP laptop, disabled USB connections, ran titan-exebl.exe and the device is booting now.
I'll continue on and see what else I can screw up.
Loaded SPL 1.20
Loaded 3.42.30
Loaded SPL 2.40
Device is back to working! Off to see if GPS is back after being lost with 3.42.02.
titan-exebl.exe
Where can I find titan-exebl.exe? Google doesn't turn up any results other than here?
titan_exitbl.exe
Never mind... just located it on my own hard drive!
Cheers!
Stuck on Bootloader
OK... I've tried titan_exitbl.exe, and it still doesn't work.
Here's my problem in chronological order:
1. I've been having a few problems (bugs) in my current custom ROM (PPC Kitchen 3.49 version), so I decided to re-flash to a stock ROM, see if the problems were fixed, and then try to flash back to a custom ROM.
2. I tried flashing to the Sprint 3.35 ROM. The RUU showed the progress bar on both my PC and the phone. But at 0%, I got a message saying "an error has occured" - or something to that effect.
3. I decided that the error was because I was running a custom ROM, and Sprint didn't like that. So I ran the Titan Relocker utility, thinking this would cure the problem.
4. I followed the steps on the screen and then got a message saying the relocker utility had completed successfully. The phone rebooted and went into the tri-color bootloader mode.
5. I retried the Sprint 3.35 ROM update, but got the same connection error, and the progress slider would never move from 0%.
6. I decided the phone had locked up and performed a reset with the stylus. The phone rebooted and went back into bootloader mode. The screen shows "TITA100 SPL-1.06.0000"
7. And that's as far as I've gotten. I've tried several hard resets using the buttons and the stylus together. I've tried removing the battery and reinstalliong... but the phone just goes back into bootloader mode.
I've tried both titan_exitbl.exe and UNI_Exitbootloader.exe, and neither utility seems to help. I get a message saying that "All data was sent... the phone will reboot now... please check your screen". The phone's screen blinks for a moment, and then returns to bootloader. Nothing can get it anywhere else.
I've tried different USB cables and ports. Activesync won't detect it, but the utility update software does.
When I run the Sprint 3.35 ROM update utility, I get an error at 11% saying "invalid vendor ID" and the update refuses to run. I tried to run the Titan Re-locker utility again, but it requires an ActiveSync connection. I've tried both enabling and disabling the USB connection in ActiveSync, but that seems to make no difference. The utility simply says no USB connection is available. The ROM update utilities will detect the device via USB - they just refuse to work with them.
I also tried running a DCD Tital 2.1.0 Bell ROM. The progress slider freezes at 0%, and then I get a message saying the RUU has encountered communication errors during the update. I've been through the recovery process the utiity suggests about a dozen times... it sill returns the phone to the bootloader screen.
So I'm getting pretty frustrated... does anyone have any ideas?
Try changing your spl back to 2.40.
Throwing it back into the tri color screen again and flash the sprint stock 3.35
But put it on the root of a fat32 formatted micro sd card in the flavor of under 2gb.
Just run the exe from your computer it will extract the files from the exe to some location on your computer, normally the ruu update folder.
There will be a ruu_sighned.nbh file locate it and copy it to the fat32 formatted card rename it TITAIMG.nbh
Let the phone boot into the bootloader and it should detect the file on the sd and update the rom for you, by stating loading ......
Then will prompt you to update press power key.
Sense you are not on sprint don't let the first time custimizations run ... pull battery once you get to your mobile today screen on first boot...
Use active sync or the sd method to update your rom to whatever you wanted originally.
Most full updates from carriers the ones that flash both the radio and rom will run regardless of the boot loader thats on the device.
Happy flashing
Just thought I'd toss in here that GPS does work, but I have to use GPS Viewer to get a lock on the satellites first.
softwind said:
OK... I've tried titan_exitbl.exe, and it still doesn't work.
Here's my problem in chronological order:
1. I've been having a few problems (bugs) in my current custom ROM (PPC Kitchen 3.49 version), so I decided to re-flash to a stock ROM, see if the problems were fixed, and then try to flash back to a custom ROM.
2. I tried flashing to the Sprint 3.35 ROM. The RUU showed the progress bar on both my PC and the phone. But at 0%, I got a message saying "an error has occured" - or something to that effect.
3. I decided that the error was because I was running a custom ROM, and Sprint didn't like that. So I ran the Titan Relocker utility, thinking this would cure the problem.
4. I followed the steps on the screen and then got a message saying the relocker utility had completed successfully. The phone rebooted and went into the tri-color bootloader mode.
5. I retried the Sprint 3.35 ROM update, but got the same connection error, and the progress slider would never move from 0%.
6. I decided the phone had locked up and performed a reset with the stylus. The phone rebooted and went back into bootloader mode. The screen shows "TITA100 SPL-1.06.0000"
7. And that's as far as I've gotten. I've tried several hard resets using the buttons and the stylus together. I've tried removing the battery and reinstalliong... but the phone just goes back into bootloader mode.
I've tried both titan_exitbl.exe and UNI_Exitbootloader.exe, and neither utility seems to help. I get a message saying that "All data was sent... the phone will reboot now... please check your screen". The phone's screen blinks for a moment, and then returns to bootloader. Nothing can get it anywhere else.
I've tried different USB cables and ports. Activesync won't detect it, but the utility update software does.
When I run the Sprint 3.35 ROM update utility, I get an error at 11% saying "invalid vendor ID" and the update refuses to run. I tried to run the Titan Re-locker utility again, but it requires an ActiveSync connection. I've tried both enabling and disabling the USB connection in ActiveSync, but that seems to make no difference. The utility simply says no USB connection is available. The ROM update utilities will detect the device via USB - they just refuse to work with them.
I also tried running a DCD Tital 2.1.0 Bell ROM. The progress slider freezes at 0%, and then I get a message saying the RUU has encountered communication errors during the update. I've been through the recovery process the utiity suggests about a dozen times... it sill returns the phone to the bootloader screen.
So I'm getting pretty frustrated... does anyone have any ideas?
Click to expand...
Click to collapse
please i have this problem how to fix this?
Please state your exact problem and what you did to cause it. Including all versions of rom and radio and bootloader.
drewcam888 said:
Please state your exact problem and what you did to cause it. Including all versions of rom and radio and bootloader.
Click to expand...
Click to collapse
Thanks!!! Ok, i cant remember eactly what is the v radio but i think 3.35 or 3.42 i cant remember exactly it's one of these. the SPL 1.06 Locked i cant unlocked i cant use titan_exitbl.... the SD update doesnt work stuck on loading.., i cant update from pc stuck 0% then Recovery Error help me. I My phone is bricked? Sorry for my english....
Did you try to install 2.4 unlocker?
drewcam888 said:
Did you try to install 2.4 unlocker?
Click to expand...
Click to collapse
Yes, i try from SD and nothing stuck on loading... from windows with RUU nothing 0% stuck and then UPDATE ERROR[262] now i don't know to do
2.4 doesnt use sd and it is run from a .exe. Make sure you aren't trying 2.47. Are you sure you tried this?
drewcam888 said:
2.4 doesnt use sd and it is run from a .exe. Make sure you aren't trying 2.47. Are you sure you tried this?
Click to expand...
Click to collapse
Ok, but how run from windows? If i cant connect via activesyncs the phone is on SPL mode i cant out of that and the msdos windows say "No device conected" when press enter from windows i cant unlock. Any idea? I'll try 2.47 but how run from windows with the phone en SPL Mode?
Please read. I said run 2.4 not 2.47. Put the phone in bootloader and it should say usb at the bottom. Then run 2.4 .exe unlocker. I think it should run without using activesync. And by spl mode do you mean the phone is in the bootloader.
drewcam888 said:
Please read. I said run 2.4 not 2.47. Put the phone in bootloader and it should say usb at the bottom. Then run 2.4 .exe unlocker. I think it should run without using activesync. And by spl mode do you mean the phone is in the bootloader.
Click to expand...
Click to collapse
Look i cant run Hard-SPL-MFG (Olipro 2.40 Unlocker) because when i run the Bat Or MSDOS Windows say "No device connect" question me if i want retray copy the file.
Ok so i guess it needs activesync. About your only option is to install a pregps rom so the phone will boot and then you can reflash the custom rom. Below is a pregps Verizon rom and radio that will work for 1.06 bootloader. Called rom 2.09.
http://forum.ppcgeeks.com/showpost.php?p=834294&postcount=4
drewcam888 said:
Ok so i guess it needs activesync. About your only option is to install a pregps rom so the phone will boot and then you can reflash the custom rom. Below is a pregps Verizon rom and radio that will work for 1.06 bootloader. Called rom 2.09.
http://forum.ppcgeeks.com/showpost.php?p=834294&postcount=4
Click to expand...
Click to collapse
No luck, method A SD Card Loading.. then cheking... then show a number corner 00028002 and say down Not allowed.
Method B, via PC and RUU then ERROR INVALID VENDOR ID.
Any idea? Thanks bro.
I think my phone is bricked... noway load the rom... i've tried load bootloader unlocked via SD last option and nothing!! damn this is so

phone just keeps rebooting

I have a htc 6800, last night i flashed a new radio 3.35.04 and a custom kitchen rom with windows 6.1 everything seemed to go ok with the flashing but now when i turn the phone on just before it gets to the home screen it reboots on its own, and it keeps doing it. last night i could use the phone for 2-3 minutes before it rebooted on its own. and now it dosent even get to the home screen what did i do wrong?
adriancox said:
I have a htc 6800, last night i flashed a new radio 3.35.04 and a custom kitchen rom with windows 6.1 everything seemed to go ok with the flashing but now when i turn the phone on just before it gets to the home screen it reboots on its own, and it keeps doing it. last night i could use the phone for 2-3 minutes before it rebooted on its own. and now it dosent even get to the home screen what did i do wrong?
Click to expand...
Click to collapse
Did you un-lock the phone prior to flashing.....what hardspl is showing now?
adriancox said:
I have a htc 6800, last night i flashed a new radio 3.35.04 and a custom kitchen rom with windows 6.1 everything seemed to go ok with the flashing but now when i turn the phone on just before it gets to the home screen it reboots on its own, and it keeps doing it. last night i could use the phone for 2-3 minutes before it rebooted on its own. and now it dosent even get to the home screen what did i do wrong?
Click to expand...
Click to collapse
This has happened to a few people. Do a Hard Reset. If that doesn't help. Then reflash the Bootloader with Hard_SPL 2.40 and reflash the radio and rom.
You must flash 3 things which must be compatible versions of each other in order for your phone to work:
Bootloader (aka SPL's)
Radio
ROM
You only mentioned the Radio and ROM, with no mention of a bootloader. You also don't mention which custom ROM you flashed.
See this thread for a list of compatible Bootlaoders / Radios / ROMs:
http://forum.xda-developers.com/showthread.php?t=392133
Assuming you flashed a DCD v3 custom ROM the bootloader you need is called
SPL 2.47 (2.47No2Chem Titan SPL EVT) (Recommended) or
SPL 2.40 (Hard-SPL 2.40-olipro)
You can find both on this forum.
Make sure you do lots of reading at this blog:
http://wiki.xda-developers.com/index.php?pagename=HTC_Titan
I seen your post over at PPCGeeks.....I posted this there for you....
Wrong hardspl......flash back to a stock pre-gps rom and then un-lock with either 2.4Olipro or 2.47 in my sig....flash radio and then flash custom rom....also I would suggest reading the tutorial in my sig....or use the Wiki here both are helpful...
thanks for your help. i will retry. if my device keeps rebooting how can i change the bootloader? my bootloader is spl 1.20.01 olipro
adriancox said:
thanks for your help. i will retry. if my device keeps rebooting how can i change the bootloader? my bootloader is spl 1.20.01 olipro
Click to expand...
Click to collapse
Enter BL and it should stop......hold simultaneously power, camera, and soft reset hole....tri-color screen will show....(hence BL) then flash pre-gps stock.....you can also try hooking it up to the computer and it will stop the reboot....I have never tried the latter so I cannot confirm...
thanks guys it worked. everything works except syncing my device and everytime i push the "settings" button to access the settings the device freezes up.
adriancox said:
thanks guys it worked. everything works except syncing my device and everytime i push the "settings" button to access the settings the device freezes up.
Click to expand...
Click to collapse
I posted a fix for the settings issue over at PPCgeeks for ya......take a look...

Categories

Resources