My first attempt to upgrade to AP4 did not succeed unfortunately (SPL to 3.50 upgrade went OK though), my power light stayed green and the display wouldn't come on.
So I took the Athena into bootloader and re-flashed back to AP3.
All seemed fine, the "Tap the screen to set up your device" screen appeared, I set it up and let the customization program run.
Unfortunately after the automatic reset at the end of the customization program, the device returned to the "Tap the screen to set up your device" and the customization program started again...
I tried interrupting the customization by soft resetting before it started executing itself, soft resetted during customization, let customization finish again (and again), but the device seems to be in an endless loop....
Any suggestions/help?
Thanks a lot in advance!
this happen because the spl and the kernel, AKA nk.exe, do not match. not sure what to do except try the new ap3 the cmonex posted **not sure if you tried that**
try the 3.0 cmonex posted and enjoy.
solved!
Thanks irus & Pawel062 (and cmonex!), that did the trick!
Probably not a bad idea to advise anybody who needs downgrading from AP4 to AP3 to use that rom. Download it from http://htc-hackers.com/uploads/ap3newspl.zip
See cmonex' thread at http://forum.xda-developers.com/showthread.php?t=386604
***great Information!***
HEY ALL,
I WAS ALSO HAVING SOME ISSUES VERY SIMILAR TO THESE WHILE TRYING TO "DOWNGRADE" TO ANY ROM FROM AP 4.0. THIS IS GREAT INFO AS I BUILD MY OWN ROMS CONSTANTLY, SO I WAS A BIT WORRIED WHEN I COULDNT SWITCH AFTER TRYING AP 4.O, BUT THANKS TO CMONEX, IRUS, & PAWEL062, WE CAN DOWNGRADE A BIT EASIER!
THANKS AGAIN!
M E G
I downloaded the http://htc-hackers.com/uploads/ap3newspl.zip
can anyone tell me the steps
note i'm stuck into the bootloader
mgozamy said:
I downloaded the http://htc-hackers.com/uploads/ap3newspl.zip
can anyone tell me the steps
note i'm stuck into the bootloader
Click to expand...
Click to collapse
just flash it with normal RUU
I have this problem of the "looping" with the customizations. My problem is that I can't get the device to a state where it is "talking" to activesync and from what I see, I need that to push this ap3spl new file.
When you say "just flash it with normal RUU" can you tell me what that means please? (sorry, noob here...) I've spent hours on the forums, wiki etc and I'm a bit lost.
I'm "trying" to get AP4 w/WM6.1 onto the device.
Purchased unlocked (new) and used on AT&T for 6 months.
Went to update the radio to 1.57 and used the unlocker first. (took out SIM/SD first of course).
Got past step one and then got a black screen on reboot...
I got AP3 to load but now I get this fun looping.. Setup device, load customizations, reboot, and start over.
Sounds like this file in this thread is my fix to at least get AP3 working but not sure how to apply. Can I do it from the bootloader?
thanks in advance for putting up with me
Oh yeah:
My current state:
ATHE100
IPL - v2.02
ATHE100 MFG
SPL -v3.50 OliNex
Eureka!
Ok, I'm not a COMPLETE noob.. (close). I'm up and running. AP3 (new spl) loaded, then loaded AP4. Woo Hoo!
No GPS
Well, I guess I'm "Almost" back up and running.
Since step three never got kicked off, it looks like my GPS rom/radio never was rewritten back to the device.
Any help on how to get just the GPS portion back?
Endless loop after flashing AP4
I have a similar problem. My Dopod U1000 was running WM6 and I upgraded to
radio version 1.58.00 no problem. After flashing AP4 I am in a cycle where my initial boot screen has black and white lines at the top and black at the bottom
Then get the Windows Mobile 6.1 screen and after automatic customizing the
PDA resets itself. I have tried to flash the AP3newspl file but it cant communicate successfully with the synced PDA. Any help?
Johnatara said:
I have a similar problem. My Dopod U1000 was running WM6 and I upgraded to
radio version 1.58.00 no problem. After flashing AP4 I am in a cycle where my initial boot screen has black and white lines at the top and black at the bottom
Then get the Windows Mobile 6.1 screen and after automatic customizing the
PDA resets itself. I have tried to flash the AP3newspl file but it cant communicate successfully with the synced PDA. Any help?
Click to expand...
Click to collapse
get into bootloader by pressing camera+reset and check your spl
you can flash a rom from here
also read this
http://forum.xda-developers.com/showthread.php?t=429013
Thanks lakeman. I reinstalled WM6 ROM from the boot loader.
My IPL v1.00 and SPL v1.20. Olipro and Radio 1.58
I have transferred enblerapi.cab to PDA and run it each time but when I flash
AP4 ROM or AP3newspl ROM I get an endless loop and my SPL stays v1.20
I cant seem to get a flash of SPL3.5 which I suspect is the problem.
Am I missing something?
Il download non funziona.
Related
Heh apologoies for title but im really stuck and desperate for any help!!
I have been trying to unlock my Cingular 8525 for many hours now without any luck.
I bought it off ebay knowing it was locked because I had seen these forums and knew it wasnt too harder job. I live in NZ we have a compatible 3G network here (they sell these phones branded as JasJams).
Anyway I dont have a cingular sim card, only a Vodafone NZ simcard. I dont know if that is a problem for me or not...
My problem is that I get part way through the update process and the connection between pc and phone gets cut everytime at the same place.
On my bootload screen during the setup it says
HERM100 IPL-SSPL by Des
HERM100 SPL-1.09.ds
and then
HERM100 IPL-1.01
HERM100 SPL-1.40.Olipro
Then I tick the appropriate checkboxes, I HAVE to soft reset my phone here to get it to sync up with my PC again, I dont think this should be a problem though,
It then gives me the button to select the Update button (Update the radio and bootloader)
So I click that, it gives the next screen, click next, tells you its going to take 10 minutes etc, so click next,
It then instantly disconnects the active sync connection and about a minute later I get an error screen saying the unlocker encountered communications errors.
I have been through this whole proccess 6 times now with no joy
Someone pleeeeeeeeease help me
Thanks
im willing to pay for a code all i want is a unlocked sim phone none of this radio stuff etc
try Wiki
http://wiki.xda-developers.com/
or alternatively
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=30&Itemid=27
Thanks but not really helpful, I have read the wiki through and through. I have tried that flashing HardSPL v7 and i get exactly the same problem.
PLEASE somebody help me
The only piece that is confusing is what to do once your done. The instructions say that you will be replacing your radio with a tweaked one to allow the unlock. After the entire process is done I assume you will need to have your favorite radio (1.40.3 in my case) handy to flash back onto your Hermes?
I also assume that flashing your favorite radio back to the Hermes won't lock it back again.
To be honest, I'd suggest going back to basics. You could try quite a few workarounds and end up doing this anyway..:
Reflash the original ROM your phone came with. Should be found easily via wiki.
Then you can start upgrading again.
If that's difficult, try flashing from your MicroSD card, which I've found never fails, having bricked my Hermes quite a few times now with my own cockamayme (sp) versions of ROMs that I've cobbled together from bits of code and chewing-gum.
as far as I know you dont need to CID unlock before flashing.... With olipro spl and custom RUU updater you can flash anything on your phone....
laurasaur, after you have installed 1.4 olipro, use custom RUU updater
http://forum.xda-developers.com/showthread.php?t=298737
use the RUU updater with your choice of Rom.
or if yo want to unlock the device before
http://forum.xda-developers.com/showthread.php?t=293665
amet said:
as far as I know you dont need to CID unlock before flashing.... With olipro spl and custom RUU updater you can flash anything on your phone....
laurasaur, after you have installed 1.4 olipro, use custom RUU updater
http://forum.xda-developers.com/showthread.php?t=298737
use the RUU updater with your choice of Rom.
or if yo want to unlock the device before
http://forum.xda-developers.com/showthread.php?t=293665
Click to expand...
Click to collapse
She want's to SIM-Unlock, not to CID-Unlock.
Do you use Vista? I encountered a similar problem with Windows Vista. Try a PC with Windows XP for the unlocking process.
ok my bad....
I've seen this issue with v1.4 Olipro. Upgrade bootloader to the latest Olipro 2.1 version then re-attempt.
ok thanks everyone for your advice but i am still screwed.
im not running vista.
i can not upgrade to olipro 2.1 because the upgrade utility always gets error 260 (update error) the update utility cannot connect to your PDA Phone.
I have now tried on 3 computers, my own, my parents and my work all resulting in the same thing.
I think now I will try and flash a WM6 rom onto my phone just using the olipro 1.4 and the custom RUU updater and see how I go but I dont have much hope
ok im currently updating the rom to wm6 as posted on the forums and oh my gosh i have a progress bar for the first time ever!! woot~~
um ok. now i have WM6 dopod version and fkn still sim locked someone help me before i throw my phone at the wall lol im going on holiday tomorrow and will have no phone for a week if i dont fix this in the next 3 hrs
Sim Unlock
http://forum.xda-developers.com/showthread.php?t=293665
laurasaur said:
On my bootload screen during the setup it says
HERM100 IPL-SSPL by Des
HERM100 SPL-1.09.ds
and then
HERM100 IPL-1.01
HERM100 SPL-1.40.Olipro
Then I tick the appropriate checkboxes, I HAVE to soft reset my phone here to get it to sync up with my PC again, I dont think this should be a problem though,
Click to expand...
Click to collapse
Do *NOT* soft reset your phone here, it is normal that activesync disconnects while the pda is in bootloader mode (activesync only works while OS is running). Just click "next, next, next" in the RUU and it will go fine.
woooa i think i love you Pof, I seriously do. Im not sure how I became such a noob at reading instructions but im sorry and thank you so much I now have progress bar
if you're short on time avoid any radio updates, they seem a bit hit and miss - its not worth upgrading then going away to find you've got a tossy signal!!!!
hope it worked out!
I got the mogul, and when I run any dcd rom Its loops to the welcome then restarts. Tried relocking, then unlocking (with olp 2.40)
I tried to install the rom first (dcd 2.2.0) then 3.27 Radio(off SD card cause wouldnt reboot)
Then I tried The 3.27 radio first, then 2.2.0 rom same thing(restarts at welcome screen)
SD card flashed back to 2.17 Sprint official, with 1.47 radio(works fine every time)
also tried it on dcd 2.1.0, and 1.6.8 all restarted in a loop,
Anyone have any suggestions on how to fix?
Or does anyone else have a good stable wm6.1 with htc touch UI rom maybe with 3.27 radio included?
I am a noob but im am starting to get this thanks for your help
do you happen to have ftouchflo cooked in somehow? if you have ftouchflo running, it wont let you calibrate the screen (for me at least).
JonnyBoy313 said:
I got the mogul, and when I run any dcd rom Its loops to the welcome then restarts. Tried relocking, then unlocking (with olp 2.40)
I tried to install the rom first (dcd 2.2.0) then 3.27 Radio(off SD card cause wouldnt reboot)
Then I tried The 3.27 radio first, then 2.2.0 rom same thing(restarts at welcome screen)
SD card flashed back to 2.17 Sprint official, with 1.47 radio(works fine every time)
also tried it on dcd 2.1.0, and 1.6.8 all restarted in a loop,
Anyone have any suggestions on how to fix?
Or does anyone else have a good stable wm6.1 with htc touch UI rom maybe with 3.27 radio included?
I am a noob but im am starting to get this thanks for your help
Click to expand...
Click to collapse
The same thing happened to me. The only way that I could get past that issue was to wait about 5 minutes until I started to calibrate the screen. It then worked..... but it would then reboot in a loop when i tried to open Activsync to configure my exchange server. (And no, I didn't have touchflo enabled).
I went back to 3.16 and it works fine.
Make sure your Olipro 2.40 unlocker took correctly. If it did not, then you will get reboots exactly as you described.
Also, did you do a hard reset after installing your latest ROM?
Hard-SPL did not install correctly... This happened to my phone as well.
Rom restarts right after welcome screen
Ill i am about to try that again, but the flash made me lose the ESPT settings.
Now I cant make any calls. I wrote all settings down , but I do not have the Unlock code, And I cant find it, (ITS NOT 000000)Running a mogul.
the reboots are because you didnt unlock correctly.
i had the same problem, i had the new rom flashed but the phone wasnt unlocked right.
you have to run titanunlocker.bat first, follow the instructions then your boot loader should show 2.40.
as for the ESPT settings, you can get the unlock code by using the attached.
your ESN hex is what you need to input to the keygen.
should be under your device information, in your settings.
Roms restart right after I tap the the Welcome
Ok I locked it again, Loaded a fresh official 2.17. Connected to activesync unlocked again, loaded a DCD 2.2.0, then 3.27 radio, restarded,set it all up,
got to page with start tab(home screen) Then starts to restart( at the same point). Maybe I dont Have the right unlocker it says 2.40(when i open with winrar)
Thanks, im very new at this but you guys have help me all the way through.
I have successfully recovered my phone in every way possible. I mean every way. But still havent seen a rom work yet. I feel like IM close though
Roms restart right after I tap the the Welcome
The Spf unlocker that ive been running does not show 2.40 in bootloader after unlock, only 1.10. But when I open it with winrar I can see the olp2.40
should i look for a different one
When I load this spf on phone, from home pc the unlocker says if you see 1.10 unhook usb then reconnect
Roms restart right after I tap the the Welcome
maybe Im not understanding how to do a hard reset a hard reset
thanks for the spc getter worked perfectely
Guys,
Call me a noob, moron, lazy.... whatever... Sry in advance.
I used this site back with my Siemens SX66 and had great success. I'm not doing so good with my 7501.
First of all, I see a million posts everywhere but it's very confusing as to what to do, what files to use, etc.. I know this is all volunteer work so I appreciate all the hard work that goes into it.
Here is my problem. I want to upgrade my 7501 to 6.1 and AP4 (I think that's what it's called).
I bought the unit unlocked and I've used it on AT&T for some time.
I've followed the instructions to upgrade the radio to 1.50 (or 1.57) and on step 2, it finished (or I thought it did) but upon reset, all I get is a black screen. And yes, I took out the SIM and Memory card prior to any of this and did a factory hard reset.
I was able to put AP3 on it but now when it reboots, it goes through a constant cycle of reboot, reload the custom software, reboot, reload custom software etc... I can't get it out of that loop.
I thought I saw something about this on a thread but after 2 hours (yes 2) of searching, nothing.
help?
ATHE100
IPL - v2.02
ATHE100 MFG
SPL -v3.50 OliNex
Fixed...
Finally found the post about AP3 and wrong SPL... Got new file, loaded, upgraded to AP4...
Working like a charm...
well, so I found out how to fully automate the process. sorry for the waiting, I was busy with life & some diamond and shift stuff
you can now just run an EXE that does all the downgrading and the modelid/wifi restore. no manual lnbs needed.
Description:
this uses a special SSPL, should be also OK in place of the original AthenaWrapper (or Unlocker Step 1), but I recommend you only use it for downgrade purposes.
this package includes:
- NBH to flash back to HardSPL 1.20.Olipro. can be replaced with other SPL NBH's but only with ones that are older than SPL 3.xx are recommended. this is only designed for SPL flash however, do not try other NBH types.
- SSPL which automates the restoring of wifi and modelid, which otherwise would always get corrupt when downgrading from SPL 3.xx. do not try to use another SSPL or you will corrupt your modelid and wifi and you will have to use manual tools (the Athena MAC BIN generator that I wrote & posted earlier) to restore them.
- RUU tailored to these needs. do not try to use another RUU for this purpose. also do not try using this RUU for anything else.
- BIG WARNING: do not even try to run this for any device other than Athena (not even the x7510). (I had to remove all modelid checking.) I do not take responsibility for such moronity (or any other kind of moron actions).
STEP BY STEP:
0. flash AP3newSPL OS image in preparation: http://htc-hackers.com/uploads/ap3newspl.zip
1. make sure Athena is running WM and synced with Activesync. do not try entering bootloader mode manually at this point! the way the Downgrader works relies on this.
2. extract the downloaded zip from Attachment to this post, you'll find an SPLDowngrader.EXE inside. run that EXE on your PC, now Athena should go to tricolour screen saying OliNex SSPL.
3. let the RUU flash.
3-TroubleShooting: if the RUU won't see device, uncheck the advanced functionalities in usb-to-pc settings in settings on the Athena.
4. it will reboot and also will hard reset your device. you will need to flash an OS compatible with old SPL now. if you are not sure how to do that, see "Extra help" below. after that, job is done.
5. +1: you should verify the modelid and SPL version is correct (ATHE100 and 1.20.Olipro). see "Extra help" below on how to enter bootloader mode to check.
Extra help: steps to help with flashing an OS if someone never flashed from bootloader before:
0. do not freak out if the OS isn't booting after downgrade. depends on what OS was on it before. maybe you will only get black screen but do not worry, read further:
1. you should manually enter SPL, by holding camera key (ALL THE WAY IN!!) while resetting. hold it until tricolour screen appears.
2. then use some other RUU / ROM package to flash an OS compatible with old SPL. job done.
NOTE 1: if the exe doesn't run then download and install .net framework from microsoft.com.
NOTE 2: if you just want to restore stock SPL, you must do it this way:
1. flash with this downgrader, with unchanged package.
2. flash OS compatible with old SPL 1.20.Olipro. this can be a stock OS.
3. use usual methods to restore stock SPL. this must be the last step, run only after you've restored stock OS!!!
Planned:
- dedicated stock SPL downgrade package
- dedicated SPL 3.50 upgrade package
these are all available already, just need userfriendly EXE package.
Tested and working great. Excellent Job as usual.
Thank you
Dear god thank you. Does this mean that our lords and lady of ROM cooking will be gracing us with an AP5 ROM sometime soonish?
Perfect!
Now i can try different ROMĀ“s and be sure, i can downgrade to an other, when i dont like a WM6.1 ROM.
Thx!
Awesome Cmonex - Thanks!
Many thanks, cmonex!
Just for clarification on step 4 above,
Do I enter boatloader manullay after this step?....or once this RUU is flashed and I see the black screen, do I just go ahead and flash my desired OS without entering manual boatloader?
Thank you cmonex for this downgrader!!!!!
Kenjari said:
Just for clarification on step 4 above,
Do I enter boatloader manullay after this step?....or once this RUU is flashed and I see the black screen, do I just go ahead and flash my desired OS without entering manual boatloader?
Thank you cmonex for this downgrader!!!!!
Click to expand...
Click to collapse
I edited step 4 to make it more clear - hopefully now you will see what is needed. let me know if still not clear enough.
(P.S: just to give background, RUU without manual bootloader entering will only work if WM is running because the RUU pushes enterbootloader.exe to the device which then puts the Athena in bootloader mode for flash without the user having to do anything. the exe will of course only run if there is an OS running under it.)
Hi Cmonex,
Excellent piece of work as usual, Its pretty clear as it is, You worry to much! Although
sticking with 3.5 for now, we have HTC stock, Ameo WM6 stock, and pawel's good work, and Irus's roms. Why swap?
NOW, have you got XP ROM onto Athena yet, if not why not
regards
Jay
Thanks cmonex, I get it now!
Sorry for the inconvienence!!!!
Thank you for everything ...
Is it possible once made the downgrade back to SPL 3.xx?
If this is so ... How do I do?
Montecristo said:
Thank you for everything ...
Is it possible once made the downgrade back to SPL 3.xx?
If this is so ... How do I do?
Click to expand...
Click to collapse
Just reflash with AP 4.0 again, you will have to go through all the upgrade again to get SPL 3.5 back on. Keep in mind if Pawel comes up with a new rom it may well need SPL 3.5 on to use it. I personaly think its worth waiting.
Regards
Jay
responderman said:
Just reflash with AP 4.0 again, you will have to go through all the upgrade again to get SPL 3.5 back on. Keep in mind if Pawel comes up with a new rom it may well need SPL 3.5 on to use it. I personaly think its worth waiting.
Regards
Jay
Click to expand...
Click to collapse
Same here, I do believe it woth waiting. We just need Pawel and AP team to give us an update on their next complete version.
Cheers
Black screen, Someone can help me!
Thanks for cmonex's contribution to Athena forum, AP4 in SPL 3.5 have given me a lot of pleasant time.
Since I discovered that the downloader has come out, because of curiosity,
I successfully downgraded to SPL1.2. Again, for curiosity, I wish to know the SPL1.2, I pushed camera buttom and soft reset at the same time, I really
seen the following:
"ATHE100
IPL-v.100
ATHE100
SPL-v1.20. Olipro"
However, I do not know how to switch back to the WM. If I press volume bottom and soft reset hole at the same time, I only get black screen with green light on. Someone can help me!
When you were in boatloader ..... I thought you were just only suppose to hit soft reset without the camera button.
Try that!
EDIT: I'm sorry panvita I read your post wrong. I thought you already flashed after the downgrade and you were only just checking to make sure you downgraded successfully by going to the boatloader screen. oops!
panvita said:
Thanks for cmonex's contribution to Athena forum, AP4 in SPL 3.5 have given me a lot of pleasant time.
Since I discovered that the downloader has come out, because of curiosity,
I successfully downgraded to SPL1.2. Again, for curiosity, I wish to know the SPL1.2, I pushed camera buttom and soft reset at the same time, I really
seen the following:
"ATHE100
IPL-v.100
ATHE100
SPL-v1.20. Olipro"
However, I do not know how to switch back to the WM. If I press volume bottom and soft reset hole at the same time, I only get black screen with green light on. Someone can help me!
Click to expand...
Click to collapse
You need to finish the rest of step 4 (or goto the extra help) and flash a 1.2 Rom
Extra help:
Click to expand...
Click to collapse
steps to help with flashing an OS if someone never flashed from bootloader before:
0. do not freak out if the OS isn't booting after downgrade. depends on what OS was on it before. maybe you will only get black screen but do not worry, read further:
1. you should manually enter SPL, by holding camera key (ALL THE WAY IN!!) while resetting. hold it until tricolour screen appears.
2. then use some other RUU / ROM package to flash an OS compatible with old SPL. job done.
Click to expand...
Click to collapse
yes please, why can't people read the instructions? :O
thanks to eagle for answering.
[OT]Women secrets...
How to have a REAL secret diary (and hide it to all males): leave it on the living room table and write in RED on the cover "Instructions Manual" [/OT]
My humble observation for AP4 under SPL 1.2.
panvita said:
Thanks for cmonex's contribution to Athena forum, AP4 in SPL 3.5 have given me a lot of pleasant time.
Since I discovered that the downloader has come out, because of curiosity,
I successfully downgraded to SPL1.2. Again, for curiosity, I wish to know the SPL1.2, I pushed camera buttom and soft reset at the same time, I really
seen the following:
"ATHE100
IPL-v.100
ATHE100
SPL-v1.20. Olipro"
However, I do not know how to switch back to the WM. If I press volume bottom and soft reset hole at the same time, I only get black screen with green light on. Someone can help me!
Click to expand...
Click to collapse
Before I pressed volume bottom and soft reset hole, I was able to see the program menu, and it is still AP4 program. I moved up by my finger, and htc flotouch still worked. I thought that I have had a AP4 under spl1.2, what a wonderful supprise. But after I pressed volume bottom and soft reset hole, what I could do is to go to AP3, and then to AP4, after that, go to downgrader. Finally, I went back to AP4 under spl 1.2. But strange things happened. Each time I soft reset the device, it went to customazation and calibration again. In orther words, I could not restore my backup file which eventually asked for a reset. Finally, I get a conclusion that AP4 cannot be used under spl 1.2 at least the present time. Because I got accustomed with AP4, then I upgraded to AP3 and then AP4 under spl 3.5. Just because my little curiosity, I have travelled around the world twice.
panvita said:
Before I pressed volume bottom and soft reset hole, I was able to see the program menu, and it is still AP4 program. I moved up by my finger, and htc flotouch still worked. I thought that I have had a AP4 under spl1.2, what a wonderful supprise. But after I pressed volume bottom and soft reset hole, what I could do is to go to AP3, and then to AP4, after that, go to downgrader. Finally, I went back to AP4 under spl 1.2. But strange things happened. Each time I soft reset the device, it went to customazation and calibration again. In orther words, I could not restore my backup file which eventually asked for a reset. Finally, I get a conclusion that AP4 cannot be used under spl 1.2 at least the present time. Because I got accustomed with AP4, then I upgraded to AP3 and then AP4 under spl 3.5. Just because my little curiosity, I have travelled around the world twice.
Click to expand...
Click to collapse
wish you had read the forum more times
it is well known that depending on the SPL version you have to get the correct rom version or you will get reset loop. AP4 is only for the newer SPL for now.
Ok, after 2 days of fighting, sweating, a pc hdd full with roms,tools,mtty,etc...
...i'm giving up. i am posting a help request for the first time since i am a xda user,
and that's been for almost 2 years now. i rather solve problems by doing research on the xda forums but this time i am out of energy.
i had an raphael before where the hacking process was pretty straightforward
and flashing a cooked rom was really idiotproof.
now i got an cool athena in my hands. i was like yeah, let's flash baby....and
the original OS didn't even last for half of a day. quick enough i realised that
this baby shouldn't be flashed the raphael way - the sd card method...
ok let's get on topic:
what i did:
flashed with the AP4 SPL 3.5 AthenaUpdater (following the howto exactly)
and well. that worked fine. the OS was booting and everything. but to my
surprise it looked like that AP4 update flash thing didn't ship another cooked
rom, but flashed my SPL only. i rather expected a SPL, CID unlock and ROM
install in one single package. i don't know what made me think that, since the
raphael has to be flashed with different stuff too before beeing able to...bla
since i was so happy to find that AP4 update howto i guess i was assuming
that this is the whole deal since it doesn't say anything about seperate CID
unlocking in that .pdf
anyway, i looked for a cooked spl 3.5 compatible rom and there i found it:
[ROM] *Updated Mar/4/2010* AGB V3.00.0 (WM6.5.5 build 23534)
and well, that was basically it. the flash went ok, but after booting only
the rom's splash screen appears and nothing further happens. hard reset
doesn't help.
i tried a few other roms after that, and again. only the rom-specific custom
flash image appears and nothing happens.
tried to flash the AP3 for SPL 3.5 ROM - same thing: flash screen says "operating system is loading", which is an bitmap picture i guess...
downgrade to SPL 1.2 doesn't seem possible since this requires a running
WM, which i don't have.
bootloader works by the way, hard reset works too, but no fix...
after a little reading i get the idea that i should have cid unlocked the device
before flashing with a cooked rom? or did i something else wrong?
any help would be appreciated
oh yeah, and mtty:
the recover from invalid id procedure doesn't fix the issue.
and:
set 14 0
task 8
doesn't fix anything too, just boots the device into the never ending flash screen....
quick questions
what does your boot screen say
and did you remove your sd and simcard before flashing
yeah, the i ofcourse removed the sd card and sim card before everything.
i am at work now but afaik my bootloader screen says:
ATHE100
IPL 2.02
SPL 3.50.Olipro
before the attempt with mtty it said
ATHE400
IPL 2.02
SPL 3.50.Olipro
something like that. is that helpful?
i'm wondering that almost nobody replies. is the athena projcet kinda dead
or am i just asking BS, i don't know. anyway, i'll keep this one posted.
i have a new status of my athena: it boots a ROM for the first time. i have flashed
it with a test rom, called:
Windows Mobile 6.1 Base ROM (Testing)
It can be found on the athena latest ROM links page.
And ofcourse there is a BUT(T)....
BUT..the configuration wizard keeps looping. Means the device boots WM6.1,
asks me to calibrate the screen. after that touchflo (or sense) shows up for a few seconds, a progress bar appears and installs some (invisible) stuff and the device reboots. Normal behaviour you'd say, but the calibration screen comes again, and the progress bar too, and reboots, and again, and again...
maybe somebody could tell me how to stop that process? it seems like the
device doesn't save the first time setup settings. how to fix it?
ultrasonyk said:
i'm wondering that almost nobody replies. is the athena projcet kinda dead
or am i just asking BS, i don't know. anyway, i'll keep this one posted.
i have a new status of my athena: it boots a ROM for the first time. i have flashed
it with a test rom, called:
Windows Mobile 6.1 Base ROM (Testing)
It can be found on the athena latest ROM links page.
And ofcourse there is a BUT(T)....
BUT..the configuration wizard keeps looping. Means the device boots WM6.1,
asks me to calibrate the screen. after that touchflo (or sense) shows up for a few seconds, a progress bar appears and installs some (invisible) stuff and the device reboots. Normal behaviour you'd say, but the calibration screen comes again, and the progress bar too, and reboots, and again, and again...
maybe somebody could tell me how to stop that process? it seems like the
device doesn't save the first time setup settings. how to fix it?
Click to expand...
Click to collapse
Hi mate
I live in a different time zone and my daily email about updates to posts comes late in my day and probably when you sleep.
There are not many people who use this device and it is really a legacy machine.
However your post gives a clue to what happened.
with the bootscreen showing athe400 initially are you sure you have an x7500/x7501 or is it the x7510?
Just make sure before you follow the solution in this thread
http://forum.xda-developers.com/showthread.php?t=387596&highlight=endless+loop
the roms are very different
Check out exactly which hardware you have
this thread is from the x7510 thread and may be worth a read if you have the x7510
Additionally cmonex has the knowlege to fix your issuues if the above doesn,t work
http://forum.xda-developers.com/showthread.php?t=441684
thank god, somebody replied with useful information
well, i must be honest i didn't pay too much attention on the model number.
after reading your post, i checked and i see that i have a X7510 advantage device.
which means as far as i can understand it:
i SHOULD have the modelid ATHE400?
which means, i messed it up by flashing it with mtty to modelID ATHE100?
which means, all the time i was installing X7500 stuff on the wrong device
and bricked it that way?
so the AP4 3.5 SPL solution is not for X7510?
which means, the AP4 3.5 SPL is a hard SPL but for another device?
and after all, what do you suggest? do i need to revert my modelID
to ATHE400 and if yes, how? and after that i should follow the 2nd
thread to install a proper hardSPL and a WM6.5 ROM of my choice?
try contacting cmonex
the author of this thread
http://forum.xda-developers.com/showthread.php?t=441684
wrote the script you used to change the device id and may have a way to reverse this
good luck
lakeman, my friend!
you pointed me to the right direction. i followed the steps for installing
hardspl for x7510 from cmonex, and yeah, the modelid changed back
to athe400 and the device was booting! seems like that hardspl also
corrects the modelid automatically.
i am still curious why the device was working after flashing with AP4 3.5 SPL
in first place, since that one is actually for X7500 devices.
i should 've read some more before going to flash that thing, i must admit.
many thanks to you lakeman, and big ups for that cmonex guy!
now it's time to look for a nice wm6.5 rom for my ATHE400
fantastic
happy to help