phone just keeps rebooting - Mogul, XV6800 ROM Development

I have a htc 6800, last night i flashed a new radio 3.35.04 and a custom kitchen rom with windows 6.1 everything seemed to go ok with the flashing but now when i turn the phone on just before it gets to the home screen it reboots on its own, and it keeps doing it. last night i could use the phone for 2-3 minutes before it rebooted on its own. and now it dosent even get to the home screen what did i do wrong?

adriancox said:
I have a htc 6800, last night i flashed a new radio 3.35.04 and a custom kitchen rom with windows 6.1 everything seemed to go ok with the flashing but now when i turn the phone on just before it gets to the home screen it reboots on its own, and it keeps doing it. last night i could use the phone for 2-3 minutes before it rebooted on its own. and now it dosent even get to the home screen what did i do wrong?
Click to expand...
Click to collapse
Did you un-lock the phone prior to flashing.....what hardspl is showing now?

adriancox said:
I have a htc 6800, last night i flashed a new radio 3.35.04 and a custom kitchen rom with windows 6.1 everything seemed to go ok with the flashing but now when i turn the phone on just before it gets to the home screen it reboots on its own, and it keeps doing it. last night i could use the phone for 2-3 minutes before it rebooted on its own. and now it dosent even get to the home screen what did i do wrong?
Click to expand...
Click to collapse
This has happened to a few people. Do a Hard Reset. If that doesn't help. Then reflash the Bootloader with Hard_SPL 2.40 and reflash the radio and rom.

You must flash 3 things which must be compatible versions of each other in order for your phone to work:
Bootloader (aka SPL's)
Radio
ROM
You only mentioned the Radio and ROM, with no mention of a bootloader. You also don't mention which custom ROM you flashed.
See this thread for a list of compatible Bootlaoders / Radios / ROMs:
http://forum.xda-developers.com/showthread.php?t=392133
Assuming you flashed a DCD v3 custom ROM the bootloader you need is called
SPL 2.47 (2.47No2Chem Titan SPL EVT) (Recommended) or
SPL 2.40 (Hard-SPL 2.40-olipro)
You can find both on this forum.
Make sure you do lots of reading at this blog:
http://wiki.xda-developers.com/index.php?pagename=HTC_Titan

I seen your post over at PPCGeeks.....I posted this there for you....
Wrong hardspl......flash back to a stock pre-gps rom and then un-lock with either 2.4Olipro or 2.47 in my sig....flash radio and then flash custom rom....also I would suggest reading the tutorial in my sig....or use the Wiki here both are helpful...

thanks for your help. i will retry. if my device keeps rebooting how can i change the bootloader? my bootloader is spl 1.20.01 olipro

adriancox said:
thanks for your help. i will retry. if my device keeps rebooting how can i change the bootloader? my bootloader is spl 1.20.01 olipro
Click to expand...
Click to collapse
Enter BL and it should stop......hold simultaneously power, camera, and soft reset hole....tri-color screen will show....(hence BL) then flash pre-gps stock.....you can also try hooking it up to the computer and it will stop the reboot....I have never tried the latter so I cannot confirm...

thanks guys it worked. everything works except syncing my device and everytime i push the "settings" button to access the settings the device freezes up.

adriancox said:
thanks guys it worked. everything works except syncing my device and everytime i push the "settings" button to access the settings the device freezes up.
Click to expand...
Click to collapse
I posted a fix for the settings issue over at PPCgeeks for ya......take a look...

Related

Bricked my phone i think

Hey everyone,
i am so upset and lost; words cannot describe it.
So i installed WM6 black shadow and everything was working except for SMS and MMS. So i am like ok i can live with that for a day till custel' rom will come out. SO i decided to upgrade the radio to 1.43 and boom here is where the problem started, No GSM on boot up. Phone doesn't boot up. I tried install 1.40 over again, still nothing. No i tried upgrade the the rom itself, i tired custel 2.5 and nothing and i tried the new Cingular rom, still same problem. the roms flash all the way. I read the wiki, and saw the mtty.exe thing but that doesn't work for me either. I am really lost and don't know what to do.
Specs
cingular 8525
hardspl v7 cid and sim unlocked.
PLEASE HELP
4.13?? 4.10??
Where did you download these radios from??
or do you mean 1.41 or 1.43??
Yeah thats what i meant, 1.40 and 1.43 sorry. You can see how upset i am.
Thanks Again
Well, if your phone turnes on .. it's not a brick.. lol .. it IS fixable... When you turn the phone on does it go RIGHT to the 3 colored screen?
@dan5.5
You need to read the unbricking thread about this, all the info you need is there.
http://forum.xda-developers.com/showthread.php?t=286755
If you are superCID I don't see how flashing a radio could have messed up your phone.. that's weird.
mrvanx said:
@dan5.5
You need to read the unbricking thread about this, all the info you need is there.
http://forum.xda-developers.com/showthread.php?t=286755
Click to expand...
Click to collapse
I read everything there and nothing seems to be working for me. I woudnt post for nothing. i dont want to be annoying.
OK im going to repost what ive said on 4wm:
We need to check if your Radio BL is functional, firstly leave HardSPL v7 on there and connect to the bootloader via mtty (il assume you know how to do this).
Issue the following commands and tell us the results please:
1) checkimage (this shows the CRC checksums of each component...id expect the radio image to show a timeout....
2) info 2 (This will verify that your CID is intact)
3) info 8 (does a bad block check)
Once youve done this, flash SPL 1.10.oli to the device and once again connect up to mtty.
4) 'rtask a' this will enter the radio bootloader you will see "Enter Radio Bootloader" or something to that effect
from now on when you type the text does NOT appear on the mtty screen.
5) 'rversion' this should return your radio bootloader version...now unfortunatly if you see nothing...you radio BL is dead and sorry your device is royally bricked. If you get something returned back onto the screen (most probably containing the text '0108') then your radio BL is fine.
Click to expand...
Click to collapse
do as instructed in that text, post your results here.
I cant falsh spl 1.10 oli. it gives me the 260 error.
the 260 error is not connected via USB right? .. weird... have you tried taking your battery out for a couple minutes, then booting into BL mode? sounds weird but this worked for me when I didnt flash hardSPL firsl..
hey mrvanx's
I can't downgrade the hardspl to 1.10, anyhelp.
I cant active sync, the phone doesnt boot up.
Is there anyway to aviod having to respond on the phone.
hey,
i can get the phone to boot up into windows and then it freezes within a couple min. what should i do. Still no gsm message and no phone. thanks
Dan
OK, so let's try and get you to a working state - I've bricked mine a couple of times and it can be quite heart-stopping, eh?
The first thing I would do is re-download radio 1.43, just incase your current one is damaged somehow.
Secondly, download Black Shadow - I know it's not the ROM you ultimately want but the aim here is to get you working again and we can move forward from there.
First, boot up into BootLoader mode (hold down the OK button on the left side of the phone and the power button and then press the reset button on the bottom, just in case you didn't know
You should come to the three colour screen and it should be reading IPL-1.04 and SPL-2.10.Olipro. If it isn't, stop here and post what it does say.
If it everything is OK at this point, when you plug your phone into your computer, it should change to USB at the bottom. Just wait for the Found New Hardware prompts to clear on your PC and then flash the black rom - choose the hardspl option in the flash program.
Once that has finished and it is at the "tap screen to set up windows..." bit, put it back into bootloader mode as above and flash the radio.
This should hopefully give you a running phone again as I know this combination works OK as I am currently using it.
Fingers crossed, don't panic, and let us know what the results are
Cheers,
Smiffy.
Nothing is working, can some please help me. Is there anyt way i can restore the spl to the original one so i can send the phone back, i just got it like 2 weeks ago. thanks
Also i have a bad block thats what i think makes the phone freeze after i boot it up.
How can i get around this, thats seems to be the biggest problem.
Hey everyone, let me give you more info.
I can fully flash any rom and and radio,
phone will boot up like 1 out of 10 times and then freezes and thats it.
i have a bad block number 6. I have hard spl v7 installed before the phone got screwed up. I cant downgrader the spl to a lower one to check if radio stack is screwed up. Can someone please help me, if you need to ask me more info feel free.

Help!!! 24 hours

I'v been up for 24 hours. I have searched, read eveything, DL every tool, rom I could find and I am tired and upset. I have followed every post to the line.
I have a G4. I used the shelltool and flashed the TNT_5.0_Wizard_Professional to it. It booted once and worked great but has never booted since. It gets to the HTC screen. and shows the IPL 2.28.0001 and the SPL 2.28.0001 the GSM 02.25.11 and the OS 6.0.0.0
At this point I don't know what to do to unbrick my phone. I tried to go into bootloader and reflash the ROM but it always gives me a no communication error. Any advice or any one having this problem and had any luck fixing this would be super helpful.
Thanks...
mixpro said:
I'v been up for 24 hours. I have searched, read eveything, DL every tool, rom I could find and I am tired and upset. I have followed every post to the line.
I have a G4. I used the shelltool and flashed the TNT_5.0_Wizard_Professional to it. It booted once and worked great but has never booted since. It gets to the HTC screen. and shows the IPL 2.28.0001 and the SPL 2.28.0001 the GSM 02.25.11 and the OS 6.0.0.0
At this point I don't know what to do to unbrick my phone. I tried to go into bootloader and reflash the ROM but it always gives me a no communication error. Any advice or any one having this problem and had any luck fixing this would be super helpful.
Thanks...
Click to expand...
Click to collapse
You don't have a brick
Load the wizard into bootmode (start and keep voicecommand button pressed until you see a three colored screen)
Then kill active sync (wcescomm.exe in taskmanager).
Connect your device
Load the original rom and flash.
After that you can reflash almost any rom to your G4 with Soft SPL.
Its faster than shelltool
Or you can CID unlock it using hard SPL, and run the Ruu from the ROM itself.
Before using Soft SPL or Hard SPL read the threads first.
Good luck,
EquinoXe
mixpro said:
I'v been up for 24 hours. I have searched, read eveything, DL every tool, rom I could find and I am tired and upset. I have followed every post to the line.
I have a G4. I used the shelltool and flashed the TNT_5.0_Wizard_Professional to it. It booted once and worked great but has never booted since. It gets to the HTC screen. and shows the IPL 2.28.0001 and the SPL 2.28.0001 the GSM 02.25.11 and the OS 6.0.0.0
At this point I don't know what to do to unbrick my phone. I tried to go into bootloader and reflash the ROM but it always gives me a no communication error. Any advice or any one having this problem and had any luck fixing this would be super helpful.
Thanks...
Click to expand...
Click to collapse
Two things:
1- 'No communication' can come from low voltage battery. Be sure to have it more than 60% before changing ROMs
2-The TNT 5.0 is a cooked ROM and is smaller than the Official ROMs.
TNT5.0 - 0x3800000
Official - 0x3900000
Which means that ShellTools can hang because of the size difference.
You don't have a brick
Load the wizard into bootmode (start and keep voicecommand button pressed until you see a three colored screen)
Then kill active sync (wcescomm.exe in taskmanager).
Connect your device
Load the original rom and flash.
After that you can reflash almost any rom to your G4 with Soft SPL.
Its faster than shelltool
Or you can CID unlock it using hard SPL, and run the Ruu from the ROM itself.
Before using Soft SPL or Hard SPL read the threads first.
Good luck,
Click to expand...
Click to collapse
I'v done all that. No matter what I do it just wont load any rom. Just keep getting the message unable to connect.
I am ready to throw this thing across the parking lot.
mixpro said:
I'v done all that. No matter what I do it just wont load any rom. Just keep getting the message unable to connect.
I am ready to throw this thing across the parking lot.
Click to expand...
Click to collapse
It's not a brick yet.
Have you tried Mestrini's tip, regarding fully charging the device?
You can also try to use another usb port and better yet, another computer, even if the initial flashing was from the computer you are using now.
Good luck,
EquinoXe
not yet..
mixpro said:
I'v done all that. No matter what I do it just wont load any rom. Just keep getting the message unable to connect.
I am ready to throw this thing across the parking lot.
Click to expand...
Click to collapse
hey,
i have been from that state already..
just use the wizard_love ROM..
yea, they are right.. you have to be in that 3 color screen..
then kill the active sync or uncheck usb connection in connections settings.
then flash the wizard love ROM..
after that, u cud flash any WM6 again..
rizortiz

Roms restart right after I tap the the Welcome screen

I got the mogul, and when I run any dcd rom Its loops to the welcome then restarts. Tried relocking, then unlocking (with olp 2.40)
I tried to install the rom first (dcd 2.2.0) then 3.27 Radio(off SD card cause wouldnt reboot)
Then I tried The 3.27 radio first, then 2.2.0 rom same thing(restarts at welcome screen)
SD card flashed back to 2.17 Sprint official, with 1.47 radio(works fine every time)
also tried it on dcd 2.1.0, and 1.6.8 all restarted in a loop,
Anyone have any suggestions on how to fix?
Or does anyone else have a good stable wm6.1 with htc touch UI rom maybe with 3.27 radio included?
I am a noob but im am starting to get this thanks for your help
do you happen to have ftouchflo cooked in somehow? if you have ftouchflo running, it wont let you calibrate the screen (for me at least).
JonnyBoy313 said:
I got the mogul, and when I run any dcd rom Its loops to the welcome then restarts. Tried relocking, then unlocking (with olp 2.40)
I tried to install the rom first (dcd 2.2.0) then 3.27 Radio(off SD card cause wouldnt reboot)
Then I tried The 3.27 radio first, then 2.2.0 rom same thing(restarts at welcome screen)
SD card flashed back to 2.17 Sprint official, with 1.47 radio(works fine every time)
also tried it on dcd 2.1.0, and 1.6.8 all restarted in a loop,
Anyone have any suggestions on how to fix?
Or does anyone else have a good stable wm6.1 with htc touch UI rom maybe with 3.27 radio included?
I am a noob but im am starting to get this thanks for your help
Click to expand...
Click to collapse
The same thing happened to me. The only way that I could get past that issue was to wait about 5 minutes until I started to calibrate the screen. It then worked..... but it would then reboot in a loop when i tried to open Activsync to configure my exchange server. (And no, I didn't have touchflo enabled).
I went back to 3.16 and it works fine.
Make sure your Olipro 2.40 unlocker took correctly. If it did not, then you will get reboots exactly as you described.
Also, did you do a hard reset after installing your latest ROM?
Hard-SPL did not install correctly... This happened to my phone as well.
Rom restarts right after welcome screen
Ill i am about to try that again, but the flash made me lose the ESPT settings.
Now I cant make any calls. I wrote all settings down , but I do not have the Unlock code, And I cant find it, (ITS NOT 000000)Running a mogul.
the reboots are because you didnt unlock correctly.
i had the same problem, i had the new rom flashed but the phone wasnt unlocked right.
you have to run titanunlocker.bat first, follow the instructions then your boot loader should show 2.40.
as for the ESPT settings, you can get the unlock code by using the attached.
your ESN hex is what you need to input to the keygen.
should be under your device information, in your settings.
Roms restart right after I tap the the Welcome
Ok I locked it again, Loaded a fresh official 2.17. Connected to activesync unlocked again, loaded a DCD 2.2.0, then 3.27 radio, restarded,set it all up,
got to page with start tab(home screen) Then starts to restart( at the same point). Maybe I dont Have the right unlocker it says 2.40(when i open with winrar)
Thanks, im very new at this but you guys have help me all the way through.
I have successfully recovered my phone in every way possible. I mean every way. But still havent seen a rom work yet. I feel like IM close though
Roms restart right after I tap the the Welcome
The Spf unlocker that ive been running does not show 2.40 in bootloader after unlock, only 1.10. But when I open it with winrar I can see the olp2.40
should i look for a different one
When I load this spf on phone, from home pc the unlocker says if you see 1.10 unhook usb then reconnect
Roms restart right after I tap the the Welcome
maybe Im not understanding how to do a hard reset a hard reset
thanks for the spc getter worked perfectely

reverting to AP3 after failed AP4 upgrade --> customization reset loop

My first attempt to upgrade to AP4 did not succeed unfortunately (SPL to 3.50 upgrade went OK though), my power light stayed green and the display wouldn't come on.
So I took the Athena into bootloader and re-flashed back to AP3.
All seemed fine, the "Tap the screen to set up your device" screen appeared, I set it up and let the customization program run.
Unfortunately after the automatic reset at the end of the customization program, the device returned to the "Tap the screen to set up your device" and the customization program started again...
I tried interrupting the customization by soft resetting before it started executing itself, soft resetted during customization, let customization finish again (and again), but the device seems to be in an endless loop....
Any suggestions/help?
Thanks a lot in advance!
this happen because the spl and the kernel, AKA nk.exe, do not match. not sure what to do except try the new ap3 the cmonex posted **not sure if you tried that**
try the 3.0 cmonex posted and enjoy.
solved!
Thanks irus & Pawel062 (and cmonex!), that did the trick!
Probably not a bad idea to advise anybody who needs downgrading from AP4 to AP3 to use that rom. Download it from http://htc-hackers.com/uploads/ap3newspl.zip
See cmonex' thread at http://forum.xda-developers.com/showthread.php?t=386604
***great Information!***
HEY ALL,
I WAS ALSO HAVING SOME ISSUES VERY SIMILAR TO THESE WHILE TRYING TO "DOWNGRADE" TO ANY ROM FROM AP 4.0. THIS IS GREAT INFO AS I BUILD MY OWN ROMS CONSTANTLY, SO I WAS A BIT WORRIED WHEN I COULDNT SWITCH AFTER TRYING AP 4.O, BUT THANKS TO CMONEX, IRUS, & PAWEL062, WE CAN DOWNGRADE A BIT EASIER!
THANKS AGAIN!
M E G
I downloaded the http://htc-hackers.com/uploads/ap3newspl.zip
can anyone tell me the steps
note i'm stuck into the bootloader
mgozamy said:
I downloaded the http://htc-hackers.com/uploads/ap3newspl.zip
can anyone tell me the steps
note i'm stuck into the bootloader
Click to expand...
Click to collapse
just flash it with normal RUU
I have this problem of the "looping" with the customizations. My problem is that I can't get the device to a state where it is "talking" to activesync and from what I see, I need that to push this ap3spl new file.
When you say "just flash it with normal RUU" can you tell me what that means please? (sorry, noob here...) I've spent hours on the forums, wiki etc and I'm a bit lost.
I'm "trying" to get AP4 w/WM6.1 onto the device.
Purchased unlocked (new) and used on AT&T for 6 months.
Went to update the radio to 1.57 and used the unlocker first. (took out SIM/SD first of course).
Got past step one and then got a black screen on reboot...
I got AP3 to load but now I get this fun looping.. Setup device, load customizations, reboot, and start over.
Sounds like this file in this thread is my fix to at least get AP3 working but not sure how to apply. Can I do it from the bootloader?
thanks in advance for putting up with me
Oh yeah:
My current state:
ATHE100
IPL - v2.02
ATHE100 MFG
SPL -v3.50 OliNex
Eureka!
Ok, I'm not a COMPLETE noob.. (close). I'm up and running. AP3 (new spl) loaded, then loaded AP4. Woo Hoo!
No GPS
Well, I guess I'm "Almost" back up and running.
Since step three never got kicked off, it looks like my GPS rom/radio never was rewritten back to the device.
Any help on how to get just the GPS portion back?
Endless loop after flashing AP4
I have a similar problem. My Dopod U1000 was running WM6 and I upgraded to
radio version 1.58.00 no problem. After flashing AP4 I am in a cycle where my initial boot screen has black and white lines at the top and black at the bottom
Then get the Windows Mobile 6.1 screen and after automatic customizing the
PDA resets itself. I have tried to flash the AP3newspl file but it cant communicate successfully with the synced PDA. Any help?
Johnatara said:
I have a similar problem. My Dopod U1000 was running WM6 and I upgraded to
radio version 1.58.00 no problem. After flashing AP4 I am in a cycle where my initial boot screen has black and white lines at the top and black at the bottom
Then get the Windows Mobile 6.1 screen and after automatic customizing the
PDA resets itself. I have tried to flash the AP3newspl file but it cant communicate successfully with the synced PDA. Any help?
Click to expand...
Click to collapse
get into bootloader by pressing camera+reset and check your spl
you can flash a rom from here
also read this
http://forum.xda-developers.com/showthread.php?t=429013
Thanks lakeman. I reinstalled WM6 ROM from the boot loader.
My IPL v1.00 and SPL v1.20. Olipro and Radio 1.58
I have transferred enblerapi.cab to PDA and run it each time but when I flash
AP4 ROM or AP3newspl ROM I get an endless loop and my SPL stays v1.20
I cant seem to get a flash of SPL3.5 which I suspect is the problem.
Am I missing something?
Il download non funziona.

HOW to go to the begining?

First of all, Hi!
Now, how do I clear my nike to the point where it has nothing on it?
I need to do this because I got stuck in the process of flashing it with HARDSPL 1.22 that I need in order to flash a new rom!
I tried everything, I followed the guide on how to do HardSpl, but got stuck at step 8 of the tutorial, the process bar is constantly at 0%, and followed by recovery steps!
I do not need them because everything works just fine, only with the original rom still on!
So I want to flash a rom, but am unable to!
Please help me!
Even if my solution is deleting everything ( I do not mean a Hard Reset- Did that 10 times ) and starting from 0!
But this is one thing I never did, and do not know where to start or what to do!
So any good soul out there willing to help, please do so!
Thanks in advance!
Ok let's try to help, can you tell us more details about your phone, model 16 or 20 keys, rom and radio.
If this is not clear just send me a pm
Regards Rataplan
Thanks, mine is a 16 key version.
Radio 1.65.28.25
Rom: 2.09.405.1
Rom date: 30.08.2008.
Protocol version: 25.98.40.07H
And I did the first few steps of flashing the HardSpl
and now it says SPL 1.22
and further more, on start up screen it says "TEST ONLY NOT FOR SALE"
BTW: I was looking of flashing your ROM but as I said, no can do!
HELP
Ok from what I see it looks to me that you already flashed a rom, just one question is it telling SPL 1.22 or SPL 1.22 Hard
just SPL
That is my problem!
Any solution!?
You need to start all over again, do you have a Niki, you can see that under the battery
Okay just read your post in the other thread, that cleared a lot of things, just do it all over again and use 1.15 instead of 1.22 maybe that will work for you, btw from what I can see you didn't do anything wrong, I also flashed directly the 1.22 and from me that works.
Just keep me informed how it goes.
Regards
The phone is niki100
There is no simlock!
What do I need to do?
Refer me to a tutorial, or just tell me everything here?
And thank you for the help so far!
Edit:
OK, I did what you said, and so far works!
But, could you please explain to me a couple of things!
1. download the attached files DONE
2. REMOVE SIM and SD CARDS !! DONE
3. connect usb cable DONE
4. copy sspl-1.16-nike.exe to your device and run it (usb cable must be connected!) DONE
5. after a few seconds "USB" appears on the display DONE
6. unplug and replug the usb cable DONE
(OPTIONAL, better to skip it! step 7. if you only want to test the sspl try flashing the attached splash screen by running ROMUpdateUtility.exe from flash-splash-niki) SKIPPED
8. you can now flash the hardspl-1.15mfg-nike.nbh by running ROMUpdateUtility.exe from flash-uspl-niki
AND NOW here is my question, in the file FLASH-USPL-NIKI there is a uspl-1.16-nike.nbh file, but here in this step it says to flesh the 1.15mfg(wich I downloaded), so do
i have to delete the 1.16 and replace it with the 1.15mfg or what?
9. after installing the hardspl you can flash any rom (rom cook project here)
Okay I think I kow what you mean, you must flash the 1.15mfg, do not copy it to your phone, you don't have to delete the 1.16.
EUREKA, it worked!
Flashed your F01-10 rom!
Now I only did the 1.15 HARD Spl
Please suggest to me a radio?
I tried flashing the Radio_1.71.09.01_25.75.40.02K and it got to 100% and then said FLASH WRITE ERROR, so I was stuck wit the old radio!
AND OMG, THE ROM IS WONDERFUL
Thank you so very very much!
I need help, i have flashed a rom but now my niki stops at the radio details. It doesn't boot to windows mobile.
How do i reflash a working rom now?
How long have you waited before taking out the battery?
It takes a while to load!
It takes a while to load yes, but 5-10 minutes is to long for it to start to boot.
It has passed 1 hour now.
Anyone knows how can i fix my niki?
2 die 4 said:
EUREKA, it worked!
Flashed your F01-10 rom!
Now I only did the 1.15 HARD Spl
Please suggest to me a radio?
I tried flashing the Radio_1.71.09.01_25.75.40.02K and it got to 100% and then said FLASH WRITE ERROR, so I was stuck wit the old radio!
AND OMG, THE ROM IS WONDERFUL
Thank you so very very much!
Click to expand...
Click to collapse
You're welcome for the rom, about the radio if you want to try the 1.71 radio you have to go back to an older radio before you flash the 1.71.
I suggest to use a 1.5.. radio, that will do the trick.
For now you can always put Hardspl 1.22 on your phone, some people are recommended that if you flash a wm 6.5 rom, personally I don't see any difference.
Btw The radio I use is 1.65.29.22
Regards
masterxiter said:
It has passed 1 hour now.
Anyone knows how can i fix my niki?
Click to expand...
Click to collapse
Hmm, that's a long time without a phone , did you already try a hardreset, just turn the phone off, and turn it on by pressing the power and the send and end key on the dame time, I think that will do it.
Just keep me informed.
Regards
Rataplan said:
Hmm, that's a long time without a phone , did you already try a hardreset, just turn the phone off, and turn it on by pressing the power and the send and end key on the dame time, I think that will do it.
Just keep me informed.
Regards
Click to expand...
Click to collapse
Yes it enters restore mode. If i have the usb cable, when the restore finishes, on the pc it says "unrecognized usb" / Unknown device. I reboot the phone and its the same.
masterxiter said:
Yes it enters restore mode. If i have the usb cable, when the restore finishes, on the pc it says "unrecognized usb" / Unknown device. I reboot the phone and its the same.
Click to expand...
Click to collapse
Hmm, okay this will be diffucult, I've read you flashed a rom and after that you get this issue, just a few questions did you cid unlock your phone, and is the bootloader still there. (that is the 4 coloured screen with the spl info)
masterxiter said:
Yes it enters restore mode. If i have the usb cable, when the restore finishes, on the pc it says "unrecognized usb" / Unknown device. I reboot the phone and its the same.
Click to expand...
Click to collapse
hey dude
y dont u flash the original rom of htc nike once and then retry?
Rataplan said:
Hmm, okay this will be diffucult, I've read you flashed a rom and after that you get this issue, just a few questions did you cid unlock your phone, and is the bootloader still there. (that is the 4 coloured screen with the spl info)
Click to expand...
Click to collapse
Yes i have both.
I allready change those 4 colors for an image, lol but ok i have the spl info:
M 04
B 04
R 1.65.28.25
G 25.98.40.07W
D 2.12
What happened was, i had an working cooked rom flashed in my phone. I was working with it for about a month.
yesterday i flashed with another one. It got me 100% rebooted and voilla doesn't pass the spl boot.
masterxiter said:
Yes i have both.
I allready change those 4 colors for an image, lol but ok i have the spl info:
M 04 R 1.65.28.25
B 04 G 25.98.40.07W
D 2.12
Click to expand...
Click to collapse
Ha ha yeah that would be nice if we could replace that for an image.
Okay, connect it to your computer when you're on the 4 coloured screen and see if it connect then, in the phone you see serial changing in usb, if yes just flash your original rom.

Categories

Resources