Related
i installed a new rings rom. it worked fine, then my phone froze up, now it won load pass the opening page. it just says analyzing device component..... and its frozen there. please help, i run my company thru my phone and its very important...
what type of phone do you have? if its a G1 as i have then its easy to un-brick or un-lock...just plug your phone to your PC and format your sdcard again which will erase all of its data then ya good to go or you can remove the battery place it back then hold down your home plus power button at the same time till youir phone boots to the next screen then press alt+L then altW then reboot your phone and sign back in...
if this is a post about the g1 take it to the other forum because this is about the hermes
its a herm 100. htc 8525
have you tried to do a hard reset? If not give that a try.
I hope you installed Hard SPL V3 on it first... to check - hold power, OK button above the flywheel and reset with stylus, hold in until the tri-colour screen appears. Will show IPL - 1.04 and SPL - 2.10oli (if you've installed hard SPL V7).
If so, and you tried to Hard Reset 1st with no success, try the sd card method. If thats not working, on the pc, if using XP, go to activesync's connection settings and untick "Allow USB Connections". Connect your Hermes to the pc with usb after going to bootloader. Run the RUU_Wrapper.exe file again. This should re-install the rom.
You're gonna have a heap of trouble if you haven't Hard SPLed your Hermes.
Good Luck....
I dont have hard spl v3 on my phone. when i try to load another rom or anything i get error 270 the image file is corrupted. please check your update utility. what does that mean? and how can i work thru that?
Hopefully someone can help me here
I have an HTC Mogul that I am trying to flash over to a custom ROM. Unfortunately I got a little too gung ho and didnt flash the radio over, so now the phone freezes at the HTC splash screen on start up. I have tried flashing it back to a carrier rom or even another custom rom but it gets to the loading bar and then fails out. Have tried flashing from the SD card but every image i put on there says that there is no valid image on the card.
I have looked high and low for an answer to my problem but have had little to no luck anywhere.
Rawk02 said:
Hopefully someone can help me here
I have an HTC Mogul that I am trying to flash over to a custom ROM. Unfortunately I got a little too gung ho and didnt flash the radio over, so now the phone freezes at the HTC splash screen on start up. I have tried flashing it back to a carrier rom or even another custom rom but it gets to the loading bar and then fails out. Have tried flashing from the SD card but every image i put on there says that there is no valid image on the card.
I have looked high and low for an answer to my problem but have had little to no luck anywhere.
Click to expand...
Click to collapse
Unlocked bootloader -> Custom ROM -> GPS Radio -> Boot
So as long as your bootloader is unlocked (olipro 2.40, no2chem 2.47) then go ahead and flash the Custom GPS ROM you want to use on there. Then flash a GPS Radio I use 3.42.40 and yes I have tested all the others. Then to be totally sure might as well hard reset and pull the battery for a few.
Edit: Tip I figure everyone needs to read. If flashing using RUU method (exe, or utility through usb cable) make sure you dont have a Memory card in the phone. That ensures no problems will arise like bad flashes.
If using microSD card then make sure its not plugged in while flashing. Card must be 2gb and under and be formatted fat 32, image must be named TITAIMG.nbh and be the only thing on the card, no files or folders but the .nbh
Also check in your Computers files and folders settings and make sure you have it selected to Show File Extensions. That way you know the files are getting named and assigned correctly.
The problem I am having right now is the bootloader seems borked. It will not load any files. any that i put on the card it flashes up quick and says no image file found and then back to the bootloader screen and if i try usb it goes to the point where the progress bar comes up and then errors out. Is there a way to flash the bootloader without loading into WM?
Rawk02 said:
The problem I am having right now is the bootloader seems borked. It will not load any files. any that i put on the card it flashes up quick and says no image file found and then back to the bootloader screen and if i try usb it goes to the point where the progress bar comes up and then errors out. Is there a way to flash the bootloader without loading into WM?
Click to expand...
Click to collapse
What bootloader is on there now? You should of already mentioned this in your first post, let alone your second..
Also what size memory card are you using, I hinted at that already too.
Yeah that would help
Here is what is at the top of the Bootloader:
TITA100
SPL-1.07.0000
CPLD-9
I am using a 2 gig card, tried with a 1 gig it would get the to loading screen and freeze
Rawk02 said:
Yeah that would help
Here is what is at the top of the Bootloader:
TITA100
SPL-1.07.0000
CPLD-9
I am using a 2 gig card, tried with a 1 gig it would get the to loading screen and freeze
Click to expand...
Click to collapse
Yea you messed up, you need to flash an unlocked bootloader from a functioning WM. There are ways around it and to get out of your jam.
Tell me what the phone does after unplugging it, removing the memory card, taking the battery out and letting it sit for a couple minutes. Put only the battery in and turn it on.
I need to know if it tries to boot the OS and gets stuck or if it goes to bootloader automatically.
it tries to boot to WM, goes to the HTC logo and then freezes, i still have to hold down the camera button to boot into the bootloader
Rawk02 said:
it tries to boot to WM, goes to the HTC logo and then freezes, i still have to hold down the camera button to boot into the bootloader
Click to expand...
Click to collapse
Thats not how you get into bootloader on a Titan.
Manual Bootloader mode on a Titan = Power Button + Camera Button + Reset Button (hole next to memory card slot) for a couple seconds then release.
Ok now next information that you forgot to post. What HTC Mogul is it P4000, VX6800, PPC6800, or other variant. What carrier branding is it, like what stock ROM was originally on there. Sprint, Verizon, Qwest. Exe.
I need to know this as well so we are not just trying things to you get it. I want to write you a walkthrough that hits the nail on the head.
PPC6800
Old Carrier was USCC
and it may just be this version but to get into bootloader I have just been holding down camera then at the same time holding down power holding it for a few seconds then releasing the power and it goes into BL
1: Download the following files from my HTC to Windows Unlock Tools directory. Download the Titan_Relocker.exe, a GPS radio of your choosing, and the titan_spl_olipro240.exe.
2. Now make sure you have Active Sync 4.5 installed first then the HTC windows drivers installed second (from my HTC unlock directory on my share site). Now install both of those and restart the computer, start from a fresh PC. Now disable the Active Sync usb connections just right click the Active sync icon on your PC's taskbar. Pick connection settings and then look for the Box with Allow USB connections. Clear the box (disable) the usb connections.
3. Take out the storage card and now manually put the phone into bootloader "power camera reset" and then plug the phone into the PC using a MAIN port built into the Motherboard (no hub, no front usb panel). Now use Winrar, or 7zip to extract the contents of the Titanrelocker.exe into a folder. You will then see the ROMupdateutility.exe and ExitBL.exe with a bunch of other files. Ok now Run the ROM update utitlity.exe from the extracted folder and let it flash The Stock SPL. When it is done follow the prompts on screen. Now if it reboots back to olipro bootloader then run the Exitbl.exe and soon as it reboots wait till after the first splash screen and Unplug the phone.
4. Now manually put the phone into bootloader "power camera reset" (so it restarts and goes back to bootloader). Now we are going to flash the Olipro 2.40. Use Winrar, or 7zip to extract the contents of Olipro 2.40.exe into a folder. You will then see the ROMupdateutility.exe and ExitBL.exe with a bunch of other files. Ok now Run the ROM update utitlity.exe from the extracted folder and let it flash Olipro 2.40 When it is done follow the prompts on screen. Now if it reboots back to olipro bootloader then run the Exitbl.exe and soon as it reboots wait till after the first splash screen and Unplug the phone.
5. Now manually put the phone into bootloader "power camera reset" (so it restarts and goes back to bootloader). Now you can flash a Custom ROM using RUU method or go ahead and use the microSD method.
a. You can use an RUU utility to flash the custom ROM while its still plugged in and in bootloader.
b. You can flash the custom ROM with a Micro SD card, just unplug the phone and put the card in and manually put the phone in bootloader again using power + camera + reset all at the same time for a second or two.
6: When the ROM is done installing you MUST flash a GPS radio version 3.35 and up if you are using a GPS ROM. If you use RUU method you have to perform a hard reset after flashing the radio. If you use the Micro SD method you do not have to Hard Reset.
Still it is a good idea to hard reset and then pull battery for a minute to make sure the page pool is set.
on #3 flashing it back to the stock SPL i get the same error as I have been getting, it goes to the progress bar on both the computer and phone, sits at 0% for about 30 seconds then the computer gives error 262
ok finally got it to respond to the SD card, but it has been sitting on a grey screen saying loading for a good 6 hours now, i have a feeling that this is going to take some low-level editing with mtty
PLease can anyone let me know the process to load a rom onto a HD2 that will not boot up....? Windows mobile device center will not detect it either. Bootlogger screen says I have SPL-2.08.HSPL 8G XE, and underneath it says CotullaHSPL if that is any help. I would really appreciate any help!
lisah456 said:
PLease can anyone let me know the process to load a rom onto a HD2 that will not boot up....? Windows mobile device center will not detect it either. Bootlogger screen says I have SPL-2.08.HSPL 8G XE, and underneath it says CotullaHSPL if that is any help. I would really appreciate any help!
Click to expand...
Click to collapse
After task 29 you have to flash a ROM. Task 29 wipes your device so if you don't hold down the volume down key at the end of task 29 it will not have any operating system. Just remove the battery and hold down the volume down key till you see the bootloader screen. Then flash your ROM and all is ok.
after task29,when your device reboot
press botton "volume down" and will go in bootloader mode
now if you have your device stuck in white screen,remove battery cover
press red botton for softrest and press "Volume down" botton
bobsbbq said:
After task 29 you have to flash a ROM. Task 29 wipes your device so if you don't hold down the volume down key at the end of task 29 it will not have any operating system. Just remove the battery and hold down the volume down key till you see the bootloader screen. Then flash your ROM and all is ok.
Click to expand...
Click to collapse
opsss..sorry bob
i have look now your post
My problem is that the windows mobile says that the phone is not connected?
What do I do now?
Thanking you in advanced,
Henry
kikimax said:
My problem is that the windows mobile says that the phone is not connected?
What do I do now?
Thanking you in advanced,
Henry
Click to expand...
Click to collapse
It won't because you're in the bootloader. Does it say USB at the bottom of the bootloader screen? As long as it says USB when the phone is plugged into your computer, flash a ROM and be happy
Hello!
And what if my hd2 not entering into the boot loader?
Thanx in advance
There is only one way to get into the bootloader.
Hold down volume and keep it down....
After that press the start button and your phone will boot up.
Now you will see the tree colored screen and you're in the bootloader.
Goodluck.
same problem..connected to pc but wmdc doesn't discover it so i can't flash anything.and sd card flash doesn't help.what can i do now?
wopin80 said:
same problem..connected to pc but wmdc doesn't discover it so i can't flash anything.and sd card flash doesn't help.what can i do now?
Click to expand...
Click to collapse
When you are in the bootloader screen, connect the phone to the computer /with the usb cable/ on the same bootloader screen it will change to USB - look at the bottom of the screen:
Open the folder - on your computer - where the ROM you want to flash is:
find the "RomUpdate*.exe" or "Install.exe" /if Android it will most likely say "DAF.exe" - run it as Administrator/ file and run it. Do as it says on the screen.
Do not disconnect the cable, do not touch the device. When it is finnished it will restart the device, disconnect the cable and enjoy your new OS.
wopin80 said:
same problem..connected to pc but wmdc doesn't discover it so i can't flash anything.and sd card flash doesn't help.what can i do now?
Click to expand...
Click to collapse
use a <4gb or preferably <2gb sd card - class 4 or 2 with LEOIMG.nbh.
HSPL3_pkg after that - make sure .nbh (as above on sd root) is your stock and you CLEAN-reinstall bootloader.
ps:
Then hspl, then radio, then magldr, then windows 7, the hacks, then call M$= LIVE!
Hi guys i have a similar problem. After task 29 i went into the bootloader but can't install any rom whatsoever. I have SPL 3.03 on my devide, mind no not hard spl but SPL. Can anyone please help me solve this issue? I also tried to flash using sd card but it doesn't work. Please help me save my hd2. Thanks in advance.
tmo-hd2 wont go into bootloader after task29
Hi guys, i am facing exact same thing which dannytgt faced (http://forum.xda-developers.com/show...count=1)...but with no luck what so ever.....was running a stock rom in my hd2 3.14....wanted to try wp7 and did a task29....after that...hd2 doesnt go into bootloader screen....tried all possible combinations with/without sd,sim, holding vol down, vol up, both with power tapped...power holded etc etc...hd2 always goes into stick together screen and doesnt progress as there is os to load....opened up the mobile and tried with a pin to push the vol down switch directly also....all hardware keys were working gr8 (including vol down and up and power keys) whn win 6.5/android was running.
i know for the fact that this is reversable....if only my hd2 can get to bootloader...i will hv os running in a jiffy....
any ideas ppl? my hd2 is 3 months old ...no warrenty cos i bought it in US and using it in india..
bootloader dont load
some more details...tried to task29 (doloop) with 100% success and then my tmo hd2 wont go into bootscreen what ever i do...its stuck for ever in "stick together"...i know there is no os to load...but i dont understand y cant my hd2 go intobootloader
so far i tried
with holding volume down and power key with a single tap
with holding volume down and holding power key
with holding volume down, volume up and power key with a single tap
with holding volume down and reset button
with/without sim
with/without SD
with/without plug in wall charger
with/without plug to pc via usb cable
observations...when i pull out the battery and put it back in and then connect to computer when the phone is still off....the charging indicator LED glows in orange.
when in this mode if i switch the phone on with power/end key....it doent start...i have to pull the usb out, the orange LED still glows...and if i tap the power/end key nothing happenes...i have to pullout the battery to get it to start and eventually get stuck in "stick together"..
would really appriciate if any1 can help me get my hd2 into bootloader screen...
gdsbalaji said:
some more details...tried to task29 (doloop) with 100% success and then my tmo hd2 wont go into bootscreen what ever i do...its stuck for ever in "stick together"...i know there is no os to load...but i dont understand y cant my hd2 go intobootloader
so far i tried
with holding volume down and power key with a single tap
with holding volume down and holding power key
with holding volume down, volume up and power key with a single tap
with holding volume down and reset button
with/without sim
with/without SD
with/without plug in wall charger
with/without plug to pc via usb cable
observations...when i pull out the battery and put it back in and then connect to computer when the phone is still off....the charging indicator LED glows in orange.
when in this mode if i switch the phone on with power/end key....it doent start...i have to pull the usb out, the orange LED still glows...and if i tap the power/end key nothing happenes...i have to pullout the battery to get it to start and eventually get stuck in "stick together"..
would really appriciate if any1 can help me get my hd2 into bootloader screen...
Click to expand...
Click to collapse
Isn't it ironic: Stick together!...
There is a guide on How to get back from WP7 here on the forum.
First i would sugest to reformat the card from WP7 bul...
If i understand correctly, you can't get into bootloader or magldr!?
So you can't do nothing?
You can try this sollution and if it doesn't work, go to the service center to reset it totaly.
There was a guy with the same problem here:
Originally Posted by splinters69 View Post
This (or something similar) happened to me. I powered down my phone but did not take out the battery and it restarted the part that loads the win 7 rom while I still got the screen with the coloured bands on.
Try, taking out the battery for 10 seconds or so then put it in while holding the volume down key and powering up.
Got stock ROM back in first time but kiss goodbye to the data on your SD card. I had to use a Canon camera to reformat the card to get back the 14GB it was hiding.
This WORKED. Thanks a TON splinters69.
For future uses, this is what I did.
1. Took out the battery for about 30 seconds.
2. Put one of the LEOIMG.NBH on storage card
3. After putting the battery held the volume down button and pressed power button.
4. It went into HSPL mode straight away and started loading the win 6.5 OS.
You saved the day Splinters69. Thanks to Clydeb1 too for that modelIDcheckbypass.
http://forum.xda-developers.com/showthread.php?t=913081
lms1407 said:
Isn't it ironic: Stick together!...
There is a guide on How to get back from WP7 here on the forum.
First i would sugest to reformat the card from WP7 bul...
If i understand correctly, you can't get into bootloader or magldr!?
So you can't do nothing?
You can try this sollution and if it doesn't work, go to the service center to reset it totaly.
There was a guy with the same problem here:
Originally Posted by splinters69 View Post
This (or something similar) happened to me. I powered down my phone but did not take out the battery and it restarted the part that loads the win 7 rom while I still got the screen with the coloured bands on.
Try, taking out the battery for 10 seconds or so then put it in while holding the volume down key and powering up.
Got stock ROM back in first time but kiss goodbye to the data on your SD card. I had to use a Canon camera to reformat the card to get back the 14GB it was hiding.
This WORKED. Thanks a TON splinters69.
For future uses, this is what I did.
1. Took out the battery for about 30 seconds.
2. Put one of the LEOIMG.NBH on storage card
3. After putting the battery held the volume down button and pressed power button.
4. It went into HSPL mode straight away and started loading the win 6.5 OS.
You saved the day Splinters69. Thanks to Clydeb1 too for that modelIDcheckbypass.
http://forum.xda-developers.com/showthread.php?t=913081
Click to expand...
Click to collapse
I hvnt even instaled MGALDR yet....task29 and hd2 went into trouble...need to get to bootloader to save it now
Tried this as well before posting....hv a 2gb sd card>formatted to fat 32> stock rrunbh to leoimg.nbh > moved to root of sd card....but this can only work if bootloader can be initiated right? i cant get to boot loader
resolved the problem myself.....hd2 is working like a charm....thanks for all your support.
SOLVED {bootloader dont load}
checkout the solution for my problem here....might help u as well.
http://forum.xda-developers.com/showpost.php?p=10644926&postcount=4
______________________________
if you feel this helped...thank me
hi there i have realy big problem i have done that task 29 trick with the blackstone advangeruu and there was something wrong after restart so i pulled the battery out.
now my phone wont do any thing when i hold nowd the start button en volume down i know it has no os. but is there any way to get in the bootloader screen hope some one can help me beceasue i need my phone.
DeAdMaNwa said:
hi there i have realy big problem i have done that task 29 trick with the blackstone advangeruu and there was something wrong after restart so i pulled the battery out.
now my phone wont do any thing when i hold nowd the start button en volume down i know it has no os. but is there any way to get in the bootloader screen hope some one can help me beceasue i need my phone.
Click to expand...
Click to collapse
Man, did you say blackstone? You should go into Blackstone forum
To go into bootloader, turn off the phone. Press volume down button and the POWER ON button (not start button) at the same time until the screen appear. It works on both Leo and Black Stone
Goodluck
I'm stuck at the "GO GO GO!" screen with MAGLDR 1.10. I understand that 1.11 fixes this issue, but have not seen any clear instructions for getting 1.11 once you're stuck at the GO GO GO! screen with 1.11.
Every time I turn the phone on it just goes back to the GO GO GO! screen and sits there.
1. I tried doing a hard reset (holding down the volume button and booting). It says factory settings restored but it really doesn't do anything, still gets stuck at "GO GO GO!".
2. Neither HSPL3_PKG.exe or ROMUpdateUtility.exe for 1.11 can connect to the phone when it's stuck at the GO GO GO! screen.
EDIT (fixed):
Looks like I figured it out.
Turn the phone off (pop the battery out), and turn it back on with the volume-down button held down. Then, with it plugged into the USB, run ROMUpdateUtility.exe for 1.11.
Hopefully this saves others time who were in my situation.
ssmk said:
I'm stuck at the "GO GO GO!" screen with MAGLDR 1.10. I understand that 1.11 fixes this issue, but have not seen any clear instructions for getting 1.11 once you're stuck at the GO GO GO! screen with 1.11.
Every time I turn the phone on it just goes back to the GO GO GO! screen and sits there.
1. I tried doing a hard reset (holding down the volume button and booting). It says factory settings restored but it really doesn't do anything, still gets stuck at "GO GO GO!".
2. Neither HSPL3_PKG.exe or ROMUpdateUtility.exe for 1.11 can connect to the phone when it's stuck at the GO GO GO! screen.
Click to expand...
Click to collapse
You need to make a clean install of an official WM ROM from SD which replaces both hspl and magldr. Load Android and via HTCSync copy the LEOIMG.nbh to your SD card root. Then do the steps again but this time install magldr 1.11..
Hope I helped.. Have a nice new year..
ssmk said:
Looks like I figured it out.
Turn the phone off (pop the battery out), and turn it back on with the volume-down button held down. Then, with it plugged into the USB, run ROMUpdateUtility.exe for 1.11.
Hopefully this saves others time who were in my situation.
Click to expand...
Click to collapse
It really did save me time from flashing it to official rom, i used your method and it worked for me, direct upgrade from 1.10 to 1.11.
I am using windows 7, when i gets into tri color screen (boot with volume down button held down) then connect to window7, then my pc start to regonized the device, just wait for the pc to install the driver from the internet, then after the pc has regonized it as "something" (i forgot the name), run the ROMUpdateUtility.exe for 1.11.
Thanks
I installed clockworkmod per instructions.
When I press the on and volume up buttons I get the appropriate message and then the system boots with the tap n tap (ugh) rom.
I never see a clockworkmod menu
What am I doing wrong?
I am having the same issue!!! I am beyond frustrated right now. I have downgraded to 1.1 and had success during one try and from now on trying to boot into Clockwork it won't let me. All it does is say booting from kernal image and then goes to the splash screen then to the box with the down arrow and continues until it goes right back to the viewsonic birds and boots to the normal rom again.
What the He!! am I doing wrong here? I have already done a factory reset with data wipe...
Instructional video
See if this helps.
How to install Clockwork mid and tnt lite - Pensacola computers
http://www.youtube.com/watch?v=27oDBi-x760
argusvision said:
See if this helps.
How to install Clockwork mid and tnt lite - Pensacola computers
http://www.youtube.com/watch?v=27oDBi-x760
Click to expand...
Click to collapse
That is exactly what I was watching and following when this happened to me. Any other ideas? I did however just return the other one after clearing the data and got another one so I am going to try and avoid doing that again.. I am going to try and tread slowly here so I can get things right....
I've had 100% success using the instructions here:
http://forum.xda-developers.com/showthread.php?t=861950
Go to the first link (Dropbox) and, if Windows, download the 2 zipped files. I will say I bought a Viewsonic G tablet back in December and I had to used the older zipped file in the DEPRECATED folder. My latest Viewsonic G tablet works with the latest files.
Unzip the 2 files, combine into one folder, plug in the USB cable, and reboot by holding the POWER button *and* the Vol- button. You should see the initial boot screen but should quickly see a black screen. Run the .bat file (nvflash_gtablet.bat). If the computer doesn't see the tablet, read the above link on how to make sure you've installed the drivers for the tablet. Once the batch file ends, your tablet will automatically reboot. I would suggest powering off the tablet before it reboots as you can install CW_Mod via NVFlash, which is what I do. Grab CW_Mod 1.1 (not 1.2). Unzip the UPDATE.ZIP file and copy RECOVERY.IMG to the folder where you combined the 2 zipped files from Dropbox. Connect your tablet to your PC via the USB cable. Reboot the tablet again by pressing the POWER button while holding the Vol- button. Same thing--i.e. initial boot screen, then a black screen. Either create a batch file or run the following command (sorry cannot remember the thread where I found this, so I take no credit for this):
nvflash.exe --bl bootloader.bin --download 9 recovery.img
This is a quick process. Once the command finishes. Unplug your USB cable from your tablet and hold down the POWER button to turn off your tablet. You can either power it back on or power it back on and check to make sure CW_Mod is installed (recommended). For this, press the POWER button while holding down the Vol+ key until you see the line of text appear in the upper left hand corner of the screen.
Again, on one of my Viewsonic G tablets, I had to use the zipped file contained in the DEPRECATED folder on the Dropbox. I can't remember what the current files did (think soft-brick).
Good luck. As I've said, I've used these steps so many times as I went through every 1.1 ROM and 1.2 ROM trying to find the one I liked and the steps were perfect. At this point, though, while in CW_Mod, I would go through the process of partitioning your system and formatting stuff.