i installed a new rings rom. it worked fine, then my phone froze up, now it won load pass the opening page. it just says analyzing device component..... and its frozen there. please help, i run my company thru my phone and its very important...
what type of phone do you have? if its a G1 as i have then its easy to un-brick or un-lock...just plug your phone to your PC and format your sdcard again which will erase all of its data then ya good to go or you can remove the battery place it back then hold down your home plus power button at the same time till youir phone boots to the next screen then press alt+L then altW then reboot your phone and sign back in...
if this is a post about the g1 take it to the other forum because this is about the hermes
its a herm 100. htc 8525
have you tried to do a hard reset? If not give that a try.
I hope you installed Hard SPL V3 on it first... to check - hold power, OK button above the flywheel and reset with stylus, hold in until the tri-colour screen appears. Will show IPL - 1.04 and SPL - 2.10oli (if you've installed hard SPL V7).
If so, and you tried to Hard Reset 1st with no success, try the sd card method. If thats not working, on the pc, if using XP, go to activesync's connection settings and untick "Allow USB Connections". Connect your Hermes to the pc with usb after going to bootloader. Run the RUU_Wrapper.exe file again. This should re-install the rom.
You're gonna have a heap of trouble if you haven't Hard SPLed your Hermes.
Good Luck....
I dont have hard spl v3 on my phone. when i try to load another rom or anything i get error 270 the image file is corrupted. please check your update utility. what does that mean? and how can i work thru that?
Related
i can't do kitl mode, after presing com + power +ok buton nothing happen, also com + power + reset, it just reset the unit, can someone help, thanks
AFAIK not all roms have KITL enabled.
Okay a dumb question since I couldn't find the info from the forums.. What is this KITL and since it's not enabled in all ROMs, are there a way to enable it or are there any original shipped roms with this KITL enabled?
I think i've a serious problem.
My Tytn has been stuck in tri-colored boot screen and shows
Herm200
IPL-1.04
Herm200
SPL-2.03
I've looked at the wiki and found this
http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
because of SPL 2.03 i should try this
http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
But when i try to come in PB_KITL_MODE nothing happens.
i guess the comm-manager key is the middle key on the right side.
Any ideas what i could do ?
Thanks for your help
CGill
cgill said:
...
But when i try to come in PB_KITL_MODE nothing happens.
i guess the comm-manager key is the middle key on the right side.
...
Click to expand...
Click to collapse
Yes, this is the comm-manager key, but I think you are just here:
pof said:
AFAIK not all roms have KITL enabled.
Click to expand...
Click to collapse
So i guess there is really no other way than to send the device to the repair center ... :-(
I only wanted to update to the WM6 official firmware. I will phone with the repair center tomorrow morning and here what they will say.
If anyone else has any idea what i could to to unbrick my device i would appriciate any help. But i think all what i could try has already be done.
I also have a SPL-2.03 Bricked Hermes... but I cannot get to the KITL mode, nothing happens and I stil lget the tri-color screen.. is there any updates on how to get to KITL, or how to unbrick without getting to KITL? And by the way, what KILT stands for?? Thanks
and by the way, when I try to get to KITL pressing the suggested buttons I get a flash of a white screen saying "no image file" it´s just a flash, then it gets to the tri-color screen. It seems to recognize the USB, as when I connect the phone, it says USB underneath the PDA screen... Pls Help!
I had the same problem a few months ago. My lil sis cell (TyTn aka 8525) just crashed on her and when I got it to do a soft reset it, booted up to the tricolor. Here's what i did:
1. Disable ActiveSync: connections -- settings -- uncheck "Allow USB Connections"
2. Remove the battery, put it back in, connect the USB cable, power on the unit (this should allow the USB port to be opened again)
3. Wait a minute or two, if you get a message that device cannot be recognized just close and ignore it
4. Open mtty.exe and select "USB" from the dialog box, then hit Ok.
5. You should see a white screen, hit enter and you should see a prompt like this: "USB>" (for some reason, I got Cmd>)
6. Type set 14 0 (do not copy and paste!!!) and hit enter
7. Soft reset with stylus
8. OS ROM and radio version should be back and OS functional, the unit isn't a BRICK anymore! (after the "set 16 0" I got it to boot but "No GSM" cell is non-functional but PDA functions work)
9. if it doesn't unbrick, repeat all the steps but with the command set 16 0
Source link: http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems#problem4 will allow you to download the mtty.exe
Hope this helps.
i have an ameo and it went dead. i can get it in the bootscreen or connect with usb. how can i get to the usb bootscreen. hard reset doesnt work then it says press action to restore factory default. but it doesnt do anything. i just want to get the rainbow screen with usb, just sop i can connect with sync or something else
please help me
Allready tried to put out your micro SD? And thenn do a reset?
Does your computer recognise your device when you plug it in?
What does the bootloader say your SPL is?
If the answer to the first question is yes then you should be able to flash one of the WM6 ROMS onto your device regardless of activesync. If your bootloader says you have Olipro's SPL then you can flash ANY ROM. Only found this out yesterday. If your device is a different spl then you'll have to install one which matches your CID.
Ameo Fix
Hold the Camera and Comm Manager button and press reset to load into Bootloader, then install ROM image
05mehmet said:
Hold the Camera and Comm Manager button and press reset to load into Bootloader, then install ROM image
Click to expand...
Click to collapse
make it and flashing sopp bei 1 %
ERROR(294): INVALID SELLER -ID
felix999
ATHE100
AOL-v1.00
ATHE100
SPL-v1.10.RP00
I have WM5.0
runing AthenaUnlocker
STEP1>>>all OK
STEP2>>>stop by 60 % and now can do nothing
only have bootloader and now corect rom...
please help???
felix999
I need to upgrade the SPL on my SPV C550 now that I have unlocked it (trying to install WM6)
Do I have to buy a mini SD card reader or can I use tools to do this from my PC.
If so which tools please and briefly how.
Cheers
John
john72821 said:
I need to upgrade the SPL on my SPV C550 now that I have unlocked it (trying to install WM6)
Do I have to buy a mini SD card reader or can I use tools to do this from my PC.
If so which tools please and briefly how.
Cheers
John
Click to expand...
Click to collapse
Although a search would solve your problem here is a mini how to:
- you need to have ParchedRUU (this includes these files: EnterBootLoader.exe, Patched_RUU.exe, ROMUpdateUtility.exe, RUUGetInfo.exe and finaly your_bootloader_name.nbf) all in the same directory. The files are availabe on the net just google it.
- establish an activesync connection with USB, to do so have the phone in standby mode (no bootloader mode)
- when connected in activesync (green icon on taskbar) run the Patched_RUU.exe
- make sure you tick the boxes and the next button and that phone battery is greater than 50%
- in the final screen hit the update button, if the .nbf is in the same directory as the Patched_RUU it will load it automatically
- wait for 3 minutes, during this time you phone will enter bootloader mode, and a red bar will show the progress on the phone and the computer
you are all done
- mike
Cheers mate that did the job.
Next I guess I get into boot loader mode and then use mmty.exe?
Any clues please on how to get into boot loader mode.
john72821 said:
Cheers mate that did the job.
Next I guess I get into boot loader mode and then use mmty.exe?
Any clues please on how to get into boot loader mode.
Click to expand...
Click to collapse
again search m8!
anw here it goes:
- go to active sync -> settngs -> disable USB connections
- switch off your phone, and while holding the camera button connect it to the USB, on the screen it will appear "Need UI upgrade? (0)" or something like that.. bottom line is press 0
- then phone enters bootloader mode. if on the lower bar i think it is the green bar it says hurricane and on the right UI then it is all good, if it says something like XIP or something then you have to switch it off and do the proccess from the begining with the camera button REMEMBER TO PRESS THE 0
- fire up the mtty.exe, remember put mtty.exe AND the bin in the C:\ directory. The only thing you need to change in the startup screen of mtty is the connection port change from com1 or something to usb and press ok
- press enter so the Cmd> shows on the blank terminal
- write without quotes "l c:\name_of_your_rom.bin" and hit enter. l is a small L short for load
- hopefully it will do the update, wait for ~10 mins and it will say that it is all done... depending on your rom you may have to change language and so...
hope this helped
- mike
Sorry to carry on a bit but I get this when I do what you suggested.
Cmd>l C:\wm6.bin
clean up the image temp buffer at 0x8C080000 Length 0x01C40000
MTTYDownloadImageNot allow operation!
Error : DownloadImage return error (code = 0xFFFFFFFF)
Ive Googled this and im sure ive unlocked my phone - but is that the same as unlocking the super CID?
i dont remember man, are we allowed to post links to other sites? anw follow this guy's tutorial it is allmost the same
http://karhoe.byethost33.com/content/view/35/1/
- mike
help..
need to flash phone from boot loader mode..no standby mode..how do i do that???
HELP!!!!!!!!!!!
Just follow my guide in the signature, but use huricane ROM instead, you need to get into the bootloader and enable AS USB mode, then run the RUU
i hv made a mistake while upgrading my spv c550(HTC Hurricane) to wm6.
i have flashed the wrong spl SPL 1.01.0109 on my fone. that spl was of htc typhoon.
now my phone is not booting up.
when i press the power button the fone gives the white disply and nothing else happens.
i cannot even get into bootloader.
the charging function works when the fone is turned off.
when i turn on the fone it dos nothing not even chaging.
is there any way to get my old fone back...
help plz
i shall be very thankfull to you.
DEAD SPV
i hv made a mistake while upgrading my spv c550(HTC Hurricane) to wm6.
i have flashed the wrong spl SPL 1.01.0109 on my fone. that spl was of htc typhoon.
now my phone is not booting up.
when i press the power button the fone gives the white disply and nothing else happens.
i cannot even get into bootloader.
the charging function works when the fone is turned off.
when i turn on the fone it dos nothing not even chaging.
is there any way to get my old fone back...
help plz
i shall be very thankfull to you.
Where I can find the latest SPL for C550?
My 8525 is stuck trying to update at 11%.....any help?
Looks like your Radio ROM may have been stuffed.
About the ONLY thing you can try is to re-install the SHIPPED STOCK ROM. WM06 updates will also be OK as they have the same CID but DON"T try any other stock rom.
Also, make sure Hard SPL is installed and try the sd card method. May have more success than with the PC.
1. Format sd card (2Gb or less) FAT32.
2. Copy .nbh file of the rom you want onto sd card and rename to hermimg.nbh .Insert back into Hermes.
3 Put Hermes into bootloader - hold power, OK button above flywheel and reset with stylus, hold ALL buttons in until you get to ttri-colour screen. If you have done everything right, follow the prompts.
If this doesn't work then you no longer have a phone. Will work as a PDA but NOT a phone ever again....
Good Luck...
ill try it again when i get home.... but as to get it out of bl screen?
ultramag69 has explained how to upgrade it, just reset the phone then enter bootloader again by doing as he said
3 Put Hermes into bootloader - hold power, OK button above flywheel and reset with stylus, hold ALL buttons in until you get to ttri-colour screen. If you have done everything right, follow the prompts.
then try flashing your carriers original rom
I'm stuck at the "GO GO GO!" screen with MAGLDR 1.10. I understand that 1.11 fixes this issue, but have not seen any clear instructions for getting 1.11 once you're stuck at the GO GO GO! screen with 1.11.
Every time I turn the phone on it just goes back to the GO GO GO! screen and sits there.
1. I tried doing a hard reset (holding down the volume button and booting). It says factory settings restored but it really doesn't do anything, still gets stuck at "GO GO GO!".
2. Neither HSPL3_PKG.exe or ROMUpdateUtility.exe for 1.11 can connect to the phone when it's stuck at the GO GO GO! screen.
EDIT (fixed):
Looks like I figured it out.
Turn the phone off (pop the battery out), and turn it back on with the volume-down button held down. Then, with it plugged into the USB, run ROMUpdateUtility.exe for 1.11.
Hopefully this saves others time who were in my situation.
ssmk said:
I'm stuck at the "GO GO GO!" screen with MAGLDR 1.10. I understand that 1.11 fixes this issue, but have not seen any clear instructions for getting 1.11 once you're stuck at the GO GO GO! screen with 1.11.
Every time I turn the phone on it just goes back to the GO GO GO! screen and sits there.
1. I tried doing a hard reset (holding down the volume button and booting). It says factory settings restored but it really doesn't do anything, still gets stuck at "GO GO GO!".
2. Neither HSPL3_PKG.exe or ROMUpdateUtility.exe for 1.11 can connect to the phone when it's stuck at the GO GO GO! screen.
Click to expand...
Click to collapse
You need to make a clean install of an official WM ROM from SD which replaces both hspl and magldr. Load Android and via HTCSync copy the LEOIMG.nbh to your SD card root. Then do the steps again but this time install magldr 1.11..
Hope I helped.. Have a nice new year..
ssmk said:
Looks like I figured it out.
Turn the phone off (pop the battery out), and turn it back on with the volume-down button held down. Then, with it plugged into the USB, run ROMUpdateUtility.exe for 1.11.
Hopefully this saves others time who were in my situation.
Click to expand...
Click to collapse
It really did save me time from flashing it to official rom, i used your method and it worked for me, direct upgrade from 1.10 to 1.11.
I am using windows 7, when i gets into tri color screen (boot with volume down button held down) then connect to window7, then my pc start to regonized the device, just wait for the pc to install the driver from the internet, then after the pc has regonized it as "something" (i forgot the name), run the ROMUpdateUtility.exe for 1.11.
Thanks