I'm stuck at the "GO GO GO!" screen with MAGLDR 1.10. I understand that 1.11 fixes this issue, but have not seen any clear instructions for getting 1.11 once you're stuck at the GO GO GO! screen with 1.11.
Every time I turn the phone on it just goes back to the GO GO GO! screen and sits there.
1. I tried doing a hard reset (holding down the volume button and booting). It says factory settings restored but it really doesn't do anything, still gets stuck at "GO GO GO!".
2. Neither HSPL3_PKG.exe or ROMUpdateUtility.exe for 1.11 can connect to the phone when it's stuck at the GO GO GO! screen.
EDIT (fixed):
Looks like I figured it out.
Turn the phone off (pop the battery out), and turn it back on with the volume-down button held down. Then, with it plugged into the USB, run ROMUpdateUtility.exe for 1.11.
Hopefully this saves others time who were in my situation.
ssmk said:
I'm stuck at the "GO GO GO!" screen with MAGLDR 1.10. I understand that 1.11 fixes this issue, but have not seen any clear instructions for getting 1.11 once you're stuck at the GO GO GO! screen with 1.11.
Every time I turn the phone on it just goes back to the GO GO GO! screen and sits there.
1. I tried doing a hard reset (holding down the volume button and booting). It says factory settings restored but it really doesn't do anything, still gets stuck at "GO GO GO!".
2. Neither HSPL3_PKG.exe or ROMUpdateUtility.exe for 1.11 can connect to the phone when it's stuck at the GO GO GO! screen.
Click to expand...
Click to collapse
You need to make a clean install of an official WM ROM from SD which replaces both hspl and magldr. Load Android and via HTCSync copy the LEOIMG.nbh to your SD card root. Then do the steps again but this time install magldr 1.11..
Hope I helped.. Have a nice new year..
ssmk said:
Looks like I figured it out.
Turn the phone off (pop the battery out), and turn it back on with the volume-down button held down. Then, with it plugged into the USB, run ROMUpdateUtility.exe for 1.11.
Hopefully this saves others time who were in my situation.
Click to expand...
Click to collapse
It really did save me time from flashing it to official rom, i used your method and it worked for me, direct upgrade from 1.10 to 1.11.
I am using windows 7, when i gets into tri color screen (boot with volume down button held down) then connect to window7, then my pc start to regonized the device, just wait for the pc to install the driver from the internet, then after the pc has regonized it as "something" (i forgot the name), run the ROMUpdateUtility.exe for 1.11.
Thanks
Related
I hate to say this but after flashing I got stuck and can't get past the 2nd splash screen.
Anyone got any ideas?
I'm Supercid and Unlocked with
Herm200
IPL - 1.01
SPL - 1.40 Olipro
flashing a WM6 rom
which rom were you flashing?
Have you tried re-flashing an original rom?
if I knew how to boot up I could flash but it stays on the 2nd splash screen so I can't connect via ActivSync and I can't read my SD card.
Just thinking now, if I can get a card reader, couldn't I do the 'Herming' thing?
allan1 said:
if I knew how to boot up I could flash but it stays on the 2nd splash screen so I can't connect via ActivSync and I can't read my SD card.
Just thinking now, if I can get a card reader, couldn't I do the 'Herming' thing?
Click to expand...
Click to collapse
Tried this yet?
Hold the right side power and left side OK buttons in while hitting the reset switch on the bottom. This should put you into the boot loader and you can re-flash from here.
Just put the device to bootloader mode by yourself and reflash a rom. Press at the same time the leftside "ok" button + the rightside "power" button + soft reset with stylus.You should see the tricolor display.Plug cable and run RUUwrapper again.
thanks mate, I forgot all about that
Ok so heres an update of what I have managed to do so far:
1.) I ran a file called titan_SPL_2.40-olipro.exe
~This seemed to kick me into a "Rainbow" screen. So at this point the program told me it was done, but not matter how many time I reset it I came back to the rainbow screen. So at this point I
2.) Ran a file called titan_radio_3.27.00.exe
~This file was required for the DCD2.3.2-Alltell.exe file, so I ran the radio file. All went well till it tried to reboot. Now all I get to is a splash screen that says Alltel. The first screen that says HTC does recognize the radio as being 3.27.
So I search and search and I then tried to famous MicroSD bootloader trick. So I take the nbh file out of the firmware installer that I was going to install, rename it to TITAIMG.nbh, I format my SD card as Fat32, I copy the file over to the SD card. I put the SD card in, I hold the record and power button down and press reset... then nothing. Just a black screen. I would like to note that while its at this black screen and I plug in the USB cable to my computer, the computer sees it as a data connection.
I'm so lost on this. All I want to have in the end of this is a working Alltel phone with GPS, so that I can use Tomtom 6 to use this $549 PPC as a GPS device.
Thank you ahead of time.
[SOLVED]
Wow I am so stupid... I was holding the Voice Command button and the power button, when I should have been pressing the Camera and Power button. LOL
Heres where I found my solution: http://forum.ppcgeeks.com/showthread.php?t=17909&page=2
and in case it gets taken down:
Found a solution. This is needs to be done once you load the DcD rom 2.3. Your phone will freeze at the splash scree. Follow the steps below to get the boot loader screen back up. Your computer will then see your phone. DONT RUN HARD-SPL... Run the RRU radio instead. Windows mobile should start right up after the auto soft reset.
Steps For Install:
1. put phone in boot loader mode can do so by holding in power button and camera button at the same time while pressing in soft rest button
2. run the unlocker and follow the on screen instructions
3. then flash phone with rom of your choice, phone will reboot and be stuck at splash screen put phone back into boot loader mode
4. then run the radio upgrade and follow on screen instructions and you should be all set
Deleted, seen that you solved it.
i installed a new rings rom. it worked fine, then my phone froze up, now it won load pass the opening page. it just says analyzing device component..... and its frozen there. please help, i run my company thru my phone and its very important...
what type of phone do you have? if its a G1 as i have then its easy to un-brick or un-lock...just plug your phone to your PC and format your sdcard again which will erase all of its data then ya good to go or you can remove the battery place it back then hold down your home plus power button at the same time till youir phone boots to the next screen then press alt+L then altW then reboot your phone and sign back in...
if this is a post about the g1 take it to the other forum because this is about the hermes
its a herm 100. htc 8525
have you tried to do a hard reset? If not give that a try.
I hope you installed Hard SPL V3 on it first... to check - hold power, OK button above the flywheel and reset with stylus, hold in until the tri-colour screen appears. Will show IPL - 1.04 and SPL - 2.10oli (if you've installed hard SPL V7).
If so, and you tried to Hard Reset 1st with no success, try the sd card method. If thats not working, on the pc, if using XP, go to activesync's connection settings and untick "Allow USB Connections". Connect your Hermes to the pc with usb after going to bootloader. Run the RUU_Wrapper.exe file again. This should re-install the rom.
You're gonna have a heap of trouble if you haven't Hard SPLed your Hermes.
Good Luck....
I dont have hard spl v3 on my phone. when i try to load another rom or anything i get error 270 the image file is corrupted. please check your update utility. what does that mean? and how can i work thru that?
Hi.
Just tryed to inst. Android in my HD2 and now it stuck with a white screen with the HTC logo.
Is it any way to fix this or do i just trach it?
I am not an expert but this happened to me once while installing SD android.
I reinstalled the original ROM from the HTC site and restored my phone to factory settings.
I tried another version of android and it worked well (since last September).
Only observation is that lately (last two month) my phone hangs a lot on both systems (droid & win) and overheats a lot and when this happens I need to wait for it to cool down (at least 20 minutes) then it accepts rebooting (I am stating this although I am not sure is it from the droid or just my HW is faulty for other reasons).
I hope this helps
I tryed a NAND install. Now I cant get conection with usb and computer
Maybe you can perform a hard reset with buttons
1. With the phone turned off, press and hold the VOLUME UP and VOLUME DOWN buttons, then press the END/POWER button shortly and release it.
2. Release the VOLUME UP and VOLUME DOWN buttons.
3. Press the VOLUME UP button to perform the hard reset, or press any other button to cancel the reset.
I hope it works
3mo said:
Maybe you can perform a hard reset with buttons
1. With the phone turned off, press and hold the VOLUME UP and VOLUME DOWN buttons, then press the END/POWER button shortly and release it.
2. Release the VOLUME UP and VOLUME DOWN buttons.
3. Press the VOLUME UP button to perform the hard reset, or press any other button to cancel the reset.
I hope it works
Click to expand...
Click to collapse
didnt work hehe still at the white htc logo screen. I migth installed the files the wrong way round?
Can you get to bootloader (3 coloured screen) by turning on the phone whilst holding vol down?
conantroutman said:
Can you get to bootloader (3 coloured screen) by turning on the phone whilst holding vol down?
Click to expand...
Click to collapse
Yes that's about the only thing i can do
Go-Fast said:
Yes that's about the only thing i can do
Click to expand...
Click to collapse
As long as you can get to bootloader its ok
I would start over from the begining.....
Does it still show that you have HSPL installed on bootloader?
If so, reflash the windows 6.5 ROM that you were using before the android flash.
Then follow the steps in this thread.
Hope that helps....
conantroutman said:
As long as you can get to bootloader its ok
I would start over from the begining.....
Does it still show that you have HSPL installed on bootloader?
If so, reflash the windows 6.5 ROM that you were using before the android flash.
Then follow the steps in this thread.
Hope that helps....
Click to expand...
Click to collapse
Thnx I'll try it later and report back
Still cant get my coputer to connect to the phone.
I get to the "red green and blue" screen, and it says
PB01100 HX-BC
SPL-2.00.HSPL 8G XE
0x85
CotullaHSPL 0x40
I'm on win7 SP1
Ok when you enter bootloader (red green blue screen) you should see "Serial" at the bottom..
When you connect to the computer it should change to "USB"
You might not see anything happen on your computer but the word at the bottom of the bootloader should change.
I might be mistaken here but Im pretty sure you need "2.08 HSPL" although your bootloader shows you have HSPL installed its not 2.08. This might be the cause of your original problem.
Once it says "USB" your ready to flash a ROM via USB as usual...
If it stays on "Serial" after a few minutes then try another USB port or computer if possible.
Enter bootloader and run the HSPL tool and choose 2.08HSPL......
Then start the process from the beggining.
Hope that helps.
conantroutman said:
Ok when you enter bootloader (red green blue screen) you should see "Serial" at the bottom..
When you connect to the computer it should change to "USB"
You might not see anything happen on your computer but the word at the bottom of the bootloader should change.
I might be mistaken here but Im pretty sure you need "2.08 HSPL" although your bootloader shows you have HSPL installed its not 2.08. This might be the cause of your original problem.
Once it says "USB" your ready to flash a ROM via USB as usual...
If it stays on "Serial" after a few minutes then try another USB port or computer if possible.
Enter bootloader and run the HSPL tool and choose 2.08HSPL......
Then start the process from the beggining.
Hope that helps.
Click to expand...
Click to collapse
Hah your a babe conantroutman lol thnx
Is this the rigth SPL ?
Not to intrude on conantroutman here but yes you have to have HSPL 2.08 and a 2.15.50.14 or 2.10.50.02 radio for MAGLDR to work. Without the HSPL 2.08 you can not flash MAGLDR and without the proper radio version MAGLDR will not even boot up.
So to answer your question yes the HSPL you have in the picture you posted is the correct HSPL.
Yep as T said, hspl is good, radio is good. Your all set.
That guide for installing android at the top of the thread is pretty damn good and will have you up and running in no time. Let us know how you get on
Sent From My Fingers To Your Face.....
thnx to both of you. I'll post here when done
Crap my call button dont work when I'm in bootloader
When your in the MAGLDR menu?
You may have to flash WM again to test the call button. Or try reflashing MAGLDR, that may help...
Sent From My Fingers To Your Face.....
I guesse it's a lost case so I just installed winmo and runing android from SD card
thnx for the help.
btw!
is there a way to get htc sense to work on a huawei u8800 or x5?
Hmmm its very weird because if your call button works in WM then it should work in MAGLDR....
Hey i have the t mobile htc hd2, and i had it for quite a while. for the past year i had a windows 6.5 energy rom installed and from the last month a had battery issues. the phone whould be locked and die in 4-5 hours. i thought it was the energy rom and i decided to install magldr so i can install android on my htc phone. i have no idea whats the hspl or radio because i haven't flashed my htc in a long time.... i just installed magldr from the energy rom.... once i did that my htc would get stuck on ad recovery go go go and now i am only able to launch windows 7. when i try to nand android it gets stuck at boot. i want to change my phone back to its original state but i cant get to the tri color screen. i tried vol down then pressing power and i tried turning phone off and hold vol down and pressing the reset button, but my phone doesn't turn on when i press the yellow reset button.
mrflasha said:
Hey i have the t mobile htc hd2, and i had it for quite a while. for the past year i had a windows 6.5 energy rom installed and from the last month a had battery issues. the phone whould be locked and die in 4-5 hours. i thought it was the energy rom and i decided to install magldr so i can install android on my htc phone. i have no idea whats the hspl or radio because i haven't flashed my htc in a long time.... i just installed magldr from the energy rom.... once i did that my htc would get stuck on ad recovery go go go and now i am only able to launch windows 7. when i try to nand android it gets stuck at boot. i want to change my phone back to its original state but i cant get to the tri color screen. i tried vol down then pressing power and i tried turning phone off and hold vol down and pressing the reset button, but my phone doesn't turn on when i press the yellow reset button.[
1.First,download a stock t-mobile rom
2.Hold down volume down key while pressing the power key.
3.Connect cable to the phone and wait for usb to connect.
4.Run your rom and wait for it to finish, done.
Click to expand...
Click to collapse
First boot into magldr menu by pressing and holding the power key and scroll to usb flasher( 5 )
Connect the usb cable and wait for drivers to install,now flash your RUU,that's it. Good luck.
Click to expand...
Click to collapse
Sorry, wrong, thats for flashing android / wp7, it doesnt work for ruu's.
samsamuel said:
Sorry, wrong, thats for flashing android / wp7, it doesnt work for ruu's.
Click to expand...
Click to collapse
Thank you very much for pointing it out to me,really appreciate it boss.