I read all the posts on upgrading the titan, and I think I might have been confused with posts for the mogul and the vx6800. I loaded the 3.35.04Radio Rom from the following post http://forum.xda-developers.com/showthread.php?t=376012, I let the entire installation go through, it actually setup sprint settings on the phone, then I loaded DCD 3.0.4.
Now everything says sprint I can make and recieve calls, but I can't get online. If I access anything online it says it can't Dail #777. I tried IOTA and that just errors out, I think thats for sprint too. I tried to flash the old radio back 3.27.00 but it only goes to 9% and spits out an error. I figured I could flash the stock back on, and then go back to DCD but I can't seem to flash backwards.
I'm not sure how to proceed from here? I felt confident, because I have used kitchens for my kaiser, and lots of different roms on my kaiser, but the TITAN is kicking my a$$. Any Ideas? I could really use some help.
you werent supposed to run customization on the sprint rom... I believe you have to flash to orginal rom then start over again. When you flash the spring 3.35 radio stop when you get to the (tap the screen) page when you first boot... then flash to dcd rom.
I just remember reading that flashing to orginal rom is easiest way to reset your phone settings to what they are supposed to be, When you ran the sprint customizations you changed phone settings you werent supposed to. You may want to search the forum a little to find another easier way to fix
robrest said:
I read all the posts on upgrading the titan, and I think I might have been confused with posts for the mogul and the vx6800. I loaded the 3.35.04Radio Rom from the following post http://forum.xda-developers.com/showthread.php?t=376012, I let the entire installation go through, it actually setup sprint settings on the phone, then I loaded DCD 3.0.4.
Now everything says sprint I can make and recieve calls, but I can't get online. If I access anything online it says it can't Dail #777. I tried IOTA and that just errors out, I think thats for sprint too. I tried to flash the old radio back 3.27.00 but it only goes to 9% and spits out an error. I figured I could flash the stock back on, and then go back to DCD but I can't seem to flash backwards.
I'm not sure how to proceed from here? I felt confident, because I have used kitchens for my kaiser, and lots of different roms on my kaiser, but the TITAN is kicking my a$$. Any Ideas? I could really use some help.
Click to expand...
Click to collapse
Here is the thread you need my friend.... XV6800 back to Verizon Stock ROM
hope that helps ya....
That should get you on the right track....
azclown said:
Here is the thread you need my friend.... XV6800 back to Verizon Stock ROM
hope that helps ya....
That should get you on the right track....
Click to expand...
Click to collapse
AZCLOWN, that sounds like a plan!!! I like it. I'm downloading the the revert ROM now. Wish me luck. I'll fill you guys in later.
Got it.... Kinda
i folowed all the posts and got the original verizon rom installed then re did the radio skipping customization, reloaded dcds latest rom. booted up great! BUT there always a but... i cant get data, i get a PPP authenticATion error. its looking for a password. i read a couple of posts that said i should load the VZW rom again and place the phone in airplane mode. i dont know now.
Do you have your username and password entered in the network settings? All Verizon customers who upgraded to this radio and rom have had to re-enter that info.
Not sure if you have or not so I will included this just incase.
Goto settings/connections/edit existing connections
Keep hitting next until you come to the screen for the user and pass.
User.... xxxxxxxxxx(your phone number)@vzw3g.com
Pass.... vzw
He went back to stock radio, then went back up to 3.35.04 which usually clears out all settings. He can try manually editing the settings such as MDN and MSID in EPST, or he may have to call Verizon if he needs an A-Key.
no good so far....
I tried the ID and password from lllboredlll, then I went back to stock rom, which contains the old radio still the same thing, even if I try the ID again. I'm gonna call verizon. I gotta call them when I have a spare couple of hours.
Any other ideas? I tried #228 still no good! o well
You are going to need to call vz and tell them you did a hrd reset and need a new a-key.
You didn't have to flash back the second time, get the rom you want set up, *then* call them. They won't give you a hard time as long as they think you did a hard reset.
Good luck,your almost there!
IM BACK
nuguy said:
You are going to need to call vz and tell them you did a hrd reset and need a new a-key.
You didn't have to flash back the second time, get the rom you want set up, *then* call them. They won't give you a hard time as long as they think you did a hard reset.
Good luck,your almost there!
Click to expand...
Click to collapse
I called VZW and I was on the phone with them for exactly 2 hours, after getting hung up on twice.... Thay actually had to ask me where I was located, and reset a switch where my connection was "stuck" After that I reloaded the radion, without customization, and then loaded DCDs rom....ITs all good now!!!! YUP YUP
Related
So I did the HardSPL when I redid the phone a couple of months ago and lately it hasn't been getting service and just stopped altogether. So I looked to see what radio version I had and it said none.
So I proceeded to update the radio but I did not do the HARDSPL again as I already did it before. Well as I went through the whole process it said there was an error and told me to remove the batter. I did all this and now it won't boot up its just at the ROM screen or whatever with the three different colors.
How do I get it to boot up so I can get it to activesync and reimage it? I'm stuck and it just won't boot so I don't know what to do. Thanks
Oh and I've tried all the steps in getting by the bootloader by disabling usb and all that and it still doesn't work
I had the exact same problem yesterday ... connect it to your USB cable, and flash it with a STANDARD ROM, ie one downloaded from your phone's provider's site.
ie. We get our TyTNs through a local HTC distributor called Leaf Wireless. I downloaded the AKU3 rom from their site, and ran it. Reflashed my TyTN to their original AKU3 ROM, and after that I could reflash with whatever I wanted to
How do I reflash if I can't get it to activsync with mycomputer or don't you need to with a standard rom flash?
So I tried to do it with an original ROM and it gets to 12% done and fails everytime. How do I get this to boot back up normally?
If you go to the wiki it tells you how to do a rom upgrade off an SD card. I would try that route and re flash a ROM and radio that you know works, then take it from there.
Is all in the wiki.
Good luck.
WB
Can you post a link to that wiki? I couldn't find the one you were referring to. Thanks
I have had the same issue and even though I still have gotten it to somewhat work I'm almost sure something is wrong and I will have to send it in for a warranty repair. Here are the steps I followed using the official 8525 rom download. http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=41&Itemid=27
After that Windows worked fine but still no radio (no gsm error). I downloaded the new radio only file off of the forums which didn't seem to work. I took my phone into the att wireless store and the lady reset my sim, somehow the radio started showing up and working.
I literally spent all day on this yesterday and it is hell. If you have any questions let me know I can guide you through it.
Check your pm's
JaredYng said:
Can you post a link to that wiki? I couldn't find the one you were referring to. Thanks
Click to expand...
Click to collapse
Not sure how you couldn't find it. Anyway here you go>> http://wiki.xda-developers.com/index.php?pagename=Hermes_SDCardFlashing
i have had many problems since i upgraded my phone. sometimes if i do a soft reset, my phone gets stuck in the rainbow screen and sometimes takes a while to get back to normal. i want to just update my phone back to normal since i actually want to send it into sprint. Can someone please let me know what i need to do in order to do this, thanks
either go to htc website or sprint website and down load latest released rom and install. It should be a complete install back to original radio and rom.
Does anyone know how to return my verizon xv6800 back to factory, I unlocked/flashed to get gps to work and it updated to windows 6.1 which i dont like and I want it back to factory. Verizon cant do anything and neither can htc. has anyone done this?
kapkanimd said:
Does anyone know how to return my verizon xv6800 back to factory, I unlocked/flashed to get gps to work and it updated to windows 6.1 which i dont like and I want it back to factory. Verizon cant do anything and neither can htc. has anyone done this?
Click to expand...
Click to collapse
You will need the Relocker found here:
http://forum.ppcgeeks.com/showthread.php?p=125160
And the original Verizon ROM and Radio found here:
http://forum.xda-developers.com/showpost.php?p=1845171&postcount=13
Geckotek said:
You will need the Relocker found here:
http://forum.ppcgeeks.com/showthread.php?p=125160
And the original Verizon ROM and Radio found here:
http://forum.xda-developers.com/showpost.php?p=1845171&postcount=13
Click to expand...
Click to collapse
and you think that will restore it completely back to normal and give me back my games, my adobe, wireless sync, voice command, etc..
is this verizon rom or something someone made?
kapkanimd said:
and you think that will restore it completely back to normal and give me back my games, my adobe, wireless sync, voice command, etc..
is this verizon rom or something someone made?
Click to expand...
Click to collapse
Geckotek said:
And the original Verizon ROM and Radio found here
Click to expand...
Click to collapse
...........
lound and clear, ok then what is the order I run these in, the locker first -> radio or rom???
kapkanimd said:
lound and clear, ok then what is the order I run these in, the locker first -> radio or rom???
Click to expand...
Click to collapse
Yes, relocker then the ROM and Radio are actually both included in the same file this time.
So run the relocker, unpack the ROM file and place the .nbh file in the RUU folder and run the ROMUpdateUtility.exe.
ok not so good luck so far, have ran the reLocker and went to your links to d/l and there is no program to run them, Im relativerly new to this and need help quick what is my next step????
lol sorry i posted before i refreshed
kapkanimd said:
ok not so good luck so far, have ran the reLocker and went to your links to d/l and there is no program to run them, Im relativerly new to this and need help quick what is my next step????
Click to expand...
Click to collapse
Did you get the RUU?
Geckotek said:
Yes, relocker then the ROM and Radio are actually both included in the same file this time.
So run the relocker, unpack the ROM file and place the .nbh file in the RUU folder and run the ROMUpdateUtility.exe.
Click to expand...
Click to collapse
ok so you are saying i dont have to flash the factory radio one??
This ROM file is the full thing that includes the radio as well, so no need for a separate radio flash.
So, just to recap here for anyone still curious...
Once you run the Relocker (which will restore your bootloader to factory - also disallowing any new custom roms) then you're ready to run the Rom Update Utility (RUU) from the ROM you downloaded from Verizon or HTC's website.
the ROM update will flash both your radio as well as your ROM. good luck!
Annoyed with all of my issues....can't get data to work w/o prompting for a login every few minutes.
Flashing back...getting everything up and working, then starting all over.
Let us know what happens
Geckotek said:
Annoyed with all of my issues....can't get data to work w/o prompting for a login every few minutes.
Flashing back...getting everything up and working, then starting all over.
Click to expand...
Click to collapse
I am curious because I have all of the files and know what to do, but so far I have not had any of the problems that everyone else has had so have not needed to try it yet, so let us know that all is well just for comfort. Thanks.
In fact, all is well.
I flashed back to the stock VZW ROM (third time I think), I made sure all of my provisioning issues with Verizon were worked out (finally had the tech "kick the switch").
1) Then I proceeded to load the 2.4 bootloader,
2) then the 3.16 Unauthorized Sprint ROM w/ radio,
3) then finally installed a cooked DCD 2.3.2 ROM.
Things to note:
1) I never let the Sprint ROM boot up
2) I had no signal so ran *22802 then hit End as soon as it connected
3) Still no signal after reboot
4) No A key, MSID, or MDN issues, but I did re-enter the MSID and MDN as discussed in other threads
5) After re-entering MSID and MDN then after reboot I had signal
6) never had to run *228 to OTA program (in the past programming with *228 has reversed the effect of re-entering the MSID and MDN)
In general, I feel that the OTA from VZW sends down some programming that conflicts with the 3.27 radio...but I have nothing to prove that.
GPS is running great (I just loaded the AstroGPSLauncher)
Not sure about Rev A. It does seem snappy. What's a good site to test from the phone?
I'm happy and not re-flashing until a solid radio for Verizon arrives.
just to let everyone know i ran the factory rom and it worked perfectly, phone is back to normal, thanks !!l
This ROM file is the full thing that includes the radio as well, so no need for a separate radio flash.
Click to expand...
Click to collapse
This is a bit off-topic so apologies...
But I am left wondering that if you can include the Radio into the rom,
Has DCD or No2Chem tried to integrate the radio flash into the rom and see if some of the issues with the radio goes away?
I doubt separate install could be a cause of anything but it might be worth looking into.
Great and wonderful gurus...I think I dug myself into it. I was hoping my first post here would one with better news...but alas I am calling on your help.
I own a Telus P4000 (TITA100) and was keen on trying out dcd's new ROM. I did the following in the following order and now I have some unfortunate results.
1. Upgraded bootloader to 2.40 using USB instructions here:
http://wiki.xda-developers.com/index.php?pagename=TitanRecentHome
2. Thought 'what the heck' and tried upgrading to bootloader 2.47 using the microSD instructions at the same address.
3. Upgraded the Radio to 3.42.50.
4. A reboot brought me to the Telus screen so I thought I had done something wrong.
5. I reverted back to Radio version 1.40
6. I reverted the bootloader to 2.07 using the instructions here: http://wiki.xda-developers.com/index.php?pagename=TitanStockHome
7. I reflashed the stock Telus ROM.
8. Results are now that I cannot make any outgoing calls or data connections
(automated voice says I need to activate my phone) and my power key does not turn the device back on once it goes into 'hibernate' mode.
I am really hoping someone can help me out. I've been searching for hours to find the original Radio (1.32) and the original bootloader (1.04) so I can put things back to the way they were but I can't find anything.
Any help is well appreciated,
Ry
PS - Update - I tried the other method of reverting back to stock (via USB) and now the bootloader is 1.04 and the Radio is 1.32. BIG Steps in the right direction....
Okay...so most of the issues seem to have been resolved and I'll call Telus to re-activate my phone tomorrow but there is one remaining question:
Did I do anything wrong here and how can I continue on my quest to give this another whirl?
(I debated not posting at all...but I figure my conundrums may help someone else later)
Extra info
For you Telus users...found the last link...programming. I completely forgot about this and thank goodness I stumbled across this link thus making me feel completely stupid but nonetheless satisfied....
http://taiu.wordpress.com/2008/02/06/updating-my-telus-p4000/
I think I'm going to bed now...
I'm glad you got it to work. I just had to mention that I thought your title was vey clever
Inescapbl said:
(automated voice says I need to activate my phone)
Click to expand...
Click to collapse
Keep in mind, at least on Verizon, when upgrading your radio from a non-GPS radio to a GPS radio, the phone will require re-authentication. The A-Key will have to be given by your provider. When I called, I basically told them I had to do a hard reset. The tech on the other end said that every time I do a hard reset, I need a new A-key. NOT!(idiot)...
nitro66215 said:
Keep in mind, at least on Verizon, when upgrading your radio from a non-GPS radio to a GPS radio, the phone will require re-authentication. The A-Key will have to be given by your provider. When I called, I basically told them I had to do a hard reset. The tech on the other end said that every time I do a hard reset, I need a new A-key. NOT!(idiot)...
Click to expand...
Click to collapse
Actually, I've only needed a new A-Key once, and that was when I hard reset my device. However, when I got my phone, I upgraded the stuff before activating.
So yes, hard-resetting does (sometimes/always?) causes you to need a new A-Key.
And even then, I didn't call in; I did the whole online "activate another phone, then reactivate the 6800" trick to avoid dealing with terrible CS
nitro66215 said:
Keep in mind, at least on Verizon, when upgrading your radio from a non-GPS radio to a GPS radio, the phone will require re-authentication. The A-Key will have to be given by your provider. When I called, I basically told them I had to do a hard reset. The tech on the other end said that every time I do a hard reset, I need a new A-key. NOT!(idiot)...
Click to expand...
Click to collapse
I don't know if this A-key thing is true anymore. On my original phone I had to do an A-Key update twice. And both times was when I upgraded the Radio. After a while I stopped having to do them.
Yesterday I got a replacement 6800 (old one had bad charging port). I activated it got it working, and immediately put on SPL 2.47, radio 3.5.42 and DCD 3.2.5 (in that order)
I DID NOT have to call verizon for an A-key update.
Inescapbl said:
For you Telus users...found the last link...programming. I completely forgot about this and thank goodness I stumbled across this link thus making me feel completely stupid but nonetheless satisfied....
http://taiu.wordpress.com/2008/02/06/updating-my-telus-p4000/
I think I'm going to bed now...
Click to expand...
Click to collapse
Also take a look at some P4000 instructions I posted here.
http://www.howardforums.com/showthread.php?t=1413430&page=1&pp=15
I have never had a problem flashing my P4000 except for when I used a Sprint ROM to get an updated radio and let the customizations run. This made it so that I could not send text messages but everything else worked fine.
Here's how I fixed it:
- used the relocker to relock the phone and restore the original bootloader
- flash with stock Telus ROM
- change to 2.40 bootloader
- flash radio (didn't use the Sprint ROM this time, used SD card method instead)
- flash DCD ROM
- run Telus carrier cab
Since then I have updated to 2.47 bootloader, updated to DCD3.2.5, went to a lower version of the radio because I was having signal issues, and then just recently went to the latest radio version. I haven't had any problems other than that one I just mentioned above.
Even when you flash with DCD's ROMs the Telus splash screen will still come up as this is not overwritten by the ROM. This will only change if you use a flasher to change it or flash with another carrier's ROM (like Sprint for example).
Without a major scew-up, you should not have had to activate your phone on Telus after unlocking and a ROM update. I've never such an issue nor anyone else I know.
1. Upgraded bootloader to 2.40 using USB instructions here:
http://wiki.xda-developers.com/index...itanRecentHome
2. Thought 'what the heck' and tried upgrading to bootloader 2.47 using the microSD instructions at the same address.
3. Upgraded the Radio to 3.42.50.
4. A reboot brought me to the Telus screen so I thought I had done something wrong.
5. I reverted back to Radio version 1.40
6. I reverted the bootloader to 2.07 using the instructions here: http://wiki.xda-developers.com/index...TitanStockHome
7. I reflashed the stock Telus ROM.
8. Results are now that I cannot make any outgoing calls or data connections
(automated voice says I need to activate my phone) and my power key does not turn the device back on once it goes into 'hibernate' mode.
Click to expand...
Click to collapse
Inescabl, in all of those steps you failed to say when and where you upgraded to a third party ROM.... Within the first two I already see a point of concern where you stated you unlocked to 2.40 and then your next step being, ''what the heck' and tried upgrading to bootloader 2.47 using the microSD instructions. How did you get into the OS? Were you still on the stock radio and ROM?? You then stated that you flashed to the latest radio, but of course a reboot would only bring you to be stuck on the Telus screen if you'd not bothered to also flash to an appropriate ROM.
From what you've described, you decided to go a bit your own way, and did not pay close enough attention to the stated steps and problem solving that I wrote in the Wiki.
I'm glad that it all worked out for you, but this should be a warning to others to not rush into things without first being clear upon what the Wiki's guides and troubleshooting offer.
Keystone,
Correct. I should have used the phrase 'reprogram' by dialing *22803 for Telus users after you reflash your phone. 'Re-activate' was the wrong term.
Second, you are also correct in that my steps failed to say that I upgraded to a third party ROM and that was what I missed. On my second attempt I did upgrade to the third party ROM and all systems are now 'go'.
Third, when I said 'what the heck' I meant that since I had successfully upgraded the bootloader to 2.40 using USB I thought I'd try upgrading to 2.47 using the MicroSD method. You don't need to go into the OS to do that but merely need to get back into the bootloader screen by pressing POWER-CAMERA-SOFT RESET.
The difficulty I had resulted from the fact that the wiki is not clear that in order to install the latest ROM you need to be connected to the phone via USB and on the bootloader screen on your phone. This is where I was slightly confused and didn't understand where to go next. Perhaps you could update your instructions a little? It's funny how one person can read something and think one thing and another can read it and not see what you were thinking!
One final note. With respect to these statement: "You then stated that you flashed to the latest radio, but of course a reboot would only bring you to be stuck on the Telus screen if you'd not bothered to also flash to an appropriate ROM.From what you've described, you decided to go a bit your own way, and did not pay close enough attention to the stated steps and problem solving that I wrote in the Wiki.I'm glad that it all worked out for you, but this should be a warning to others to not rush into things without first being clear upon what the Wiki's guides and troubleshooting offer.
Though I appreciate your response I didn't really care for this final note where you took the opportunity to jab at my personal character. I did take the time and did pay attention and did not 'go my own way'. There was just that one step that I mentioned that was confusing. My post was not a personal affront to your wiki and I do appreciate it as do many others. Instead this is perhaps an opportunity to make your wiki even better!
Thanks,
Ry
_____
unL33T,
Thanks! That's a great nutshell version for the upgrade.
Ry
Inescapbl said:
Though I appreciate your response I didn't really care for this final note where you took the opportunity to jab at my personal character.
Click to expand...
Click to collapse
I never did anything of the sort! Please, have better respect for other members here and take better care in what you read:
Keystone said:
From what you've described, you decided to go a bit your own way, and did not pay close enough attention to the stated steps and problem solving that I wrote in the Wiki.
Click to expand...
Click to collapse
I was not sure what you had presented in the OP and was trying to clarify what had occurred to cause your problems. In many such threads newer people will read and get confused, and that is why I prefer to get to the bottom and then use that information to help prevent such mishaps occurring again. As what I concluded was apparently spot on, then, dude, politely recognising what was - was certainly no comment in-any-shape-nor form upon your character. Smile.
The Wiki instructions are attempting to cover nearly all of the bases to best serve the most people and likely problems. There is no single way to flash and there are numerous roadblocks that may occur. Having a simple and linear guide may be nice, but I strongly feel that it leads to rushed and relatively uninformed short-cuts where one error or another problem can leave one stuck and confused.
Keystone,
Glad to know it was just a misunderstanding. And to clarify, at no time have I disrespected you or the other fine members of this forum who use their spare time to have some fun with their hobby.
Also for the record, you did not conclude spot on unfortunately as it was not my rushing through the instructions that caused the issue but rather the fact that there is a certain amount of extrapolation required from your instructions to get everything working correctly.
Thanks again for all your help as I do appreciate it.
You're, welcome.
, I've been tryin to update my Mogul's ROM to the newest DCD ROM(3.2.6 i think) and I ran into some issues that I can't seem to find on the wiki. The first thing I did was upgrade the SPL using nueSPL-2.47 by putting onto a FAT32 Sd card(1gb). That worked out fine it looks like. When I go into the bootloader it says what it should.
So then I moved on to upgrading the radio ROM. For this I used Titan Radio ROM 3.42.50. Inside the RAR file it came in was TITAIMG.nbh. The wiki said thats what I need so I loaded that onto my Sd card and entered bootloader. It found it and asked me to press the power button and then did the update and said it was a sucess. From there... nothing happens. it stays at the gray screen. I figured I need to reset it myself so I pressed reset and now it hangs at the big yellow screen that says SPRINT and doesnt load into the OS.
The wiki says this is because I didn't load the right rom for my phone, but I'm almost positive this is the right radio for the mogul, no? I don't know what went wrong, so I'm at a complete loss.
Anyone have any ideas on how I'm messing this up?
you need to read this: http://forum.xda-developers.com/showthread.php?t=392133
your radio has to be matched with a compatible rom, since you're on radio 3.42.50, you need a gps/reva rom, any of the ones listed at the bottom.
you can flash a rom via microsd as well, but it wont load the stock os, which is what im assuming u are still on, with a newer radio.
good luck
donpedfodelruvo said:
The wiki says this is because I didn't load the right rom for my phone, but I'm almost positive this is the right radio for the mogul, no? I don't know what went wrong, so I'm at a complete loss.
Click to expand...
Click to collapse
You've mentioned installing an appropriate bootloader and radio for DCD's 3.2.6, but you have failed to state what OS ROM is loaded or if you did attempt to flash to 3.2.6.
Hmm.. Yeah I am still on the stock Os Rom. I didn't realize the newer radio would make it incompatible. I suppose the dumb mistakes are the easiest to make.
So now, I need to update the OS Rom and I should be fine. Only problem is... I can't figure out now how to update to dcd 3.2.6. I need to flash via the SD card but I can't find the .nbh file in the RUU directory. What else am I missing?
*edit* Figured all this out, see post below.
Okay... I spoke too soon, cause I'm not out of the woods yet. i upgraded the Rom and have it working on the phone. Cept', I guess my account is no longer tied to the phone anymore, cause I can't make calls or do anything related. Is the simple way to fix this just calling sprint up and just saying I want to switch my account over to this 'new' phone? I've done that plenty to switch back and forth between the two phones I own, but I'm wondering if there's something else wrong.
I did install the sprint carrier .cab, so I know that's not an issue.
donpedfodelruvo said:
Okay... I spoke too soon, cause I'm not out of the woods yet. i upgraded the Rom and have it working on the phone. Cept', I guess my account is no longer tied to the phone anymore, cause I can't make calls or do anything related. Is the simple way to fix this just calling sprint up and just saying I want to switch my account over to this 'new' phone? I've done that plenty to switch back and forth between the two phones I own, but I'm wondering if there's something else wrong.
I did install the sprint carrier .cab, so I know that's not an issue.
Click to expand...
Click to collapse
don't tell them you want to switch or anything... Just tell them you hard reset your phone and now your having this problem.
depending on the issue.. I know with verizon I either cant make calls (needs an Akey reset) or I cant get data (needs a DMU reset). I just call them and tell them I performed a hard reset because I had an issue and now I need (one of those things) reset. I'm sure it's the same for you.. this will happen when going from non GPS to GPS radio.
i usually flash the rom first then the radio both from sd. plus i dont think the card can be a sdhc
I attempted to update my ppc after attempting to fix mms, and everything went wrong. I started this thread yesterday on ppcgeeks: http://forum.ppcgeeks.com/showthread.php?t=51416 & then http://forum.ppcgeeks.com/showthread.php?t=51461
I tried to update to vetvitos black pill rom, not realizing it was a gps rom, and now when I start my phone, it has a PPCGeeks and PPCKitchen splash screen. At the bottom it says "No Radio"
I have an Alltel 6800 flashed to cricket. I have been looking for the answer for almost 24 hours straight now, and have not found one.
From what I've been reading, this is what I think ive learned:
The only way to get these roms working is with the Olipro 2.4 SPL on my phone, but the only way to get the Hard SPL on my phone is through activesync, which can't be done if i can't get into my phone. I don't think my phone is bricked, but I don't know where to go from here.
I think I need to reflash the phone to the stock rom (i think its 1.4) but I can't find it anywhere.
Can someone please help me?
just reflash with any stock one ... go to htc's site and you can download them there... the new one stock ones for alltel have GPS enabled on the radio too ... just dont let the customizations run when flashing to stock then flash to the rom of ur choice