Related
ok, now I am totaly screwed.... imate stuck in loading screen with version numbers etc... Not going further and bootloader not available.... Is there any way to communicate with unit while it's in this mode?
what you are saying is unclear. Does your device say "Serial" (or "USB") on top with "V 1.06" on the bottom?
If so, you ARE in bootloader mode. If not, then please specify what it actually says on the screen
no, it's not in bootlader mode. it's in Tmobile screen at the bottom it says R 1.12.00
G blah
D blah
it stuck there. and I can't enter bootloader mode. looks like it's totaly dead
What happens when you try to enter bootloader (Power - Action - stylus)?
What happens when you try to press (Camera - Record - Stylus)?
GO TO HELL ROM 1.72.104
F%@#&!?G FREAK ROM!! :evil:
Please calm down... in a day or two, this problem will be solved and everyone will probably be back to where they were
((and a lot smarter than they were too))
Victor said:
What happens when you try to enter bootloader (Power - Action - stylus)?
What happens when you try to press (Camera - Record - Stylus)?
Click to expand...
Click to collapse
It both cases it still sits in this screen
Try removing the battery and waiting for a period of time (20 Mins ??)
Then try the two things again (first without the battery -- for the heck of it -- and then replace the battery and try them)
...obviously, you need to remove it from the charger too :wink:
to be clear... nothing is expected to happen when you try to do these without the battery in, except perhaps (??) clear out any remaining charge held in capacitance, if any.
Kinda like removing the batteries in the remote control of a TV and then pushing a button on it (there is always enough charge in the capacitors for a single push/command to the TV
that once happent to me
and softreset dident help
so i did a hardreset and that fixed it
fixed my data too though :/
Rudegar said:
that once happent to me
and softreset dident help
so i did a hardreset and that fixed it
fixed my data too though :/
Click to expand...
Click to collapse
nothing happenes Sent email to imate tech support. I am not sure if they going to warranty unit with Tmobile betta screen stuck on IMATE. looks like i am short 700 USD........
Is there any way to communicate with XDA2 when it stuck in this loading screen? Terminal via serial cable doesn't work. anyother low level programs are out there? please, help.
Have figured out that the problem is in the Bootloader. If there is a way to (and I know there is) revert to an older Bootloader version, then the problems will all be solved.
Problem Solved : Dead devices due to tmob 1.72 + Downgrade
OK Guys. Problem Solved : Dead devices due to tmob 1.72 + Downgrade
http://forum.xda-developers.com/viewtopic.php?t=8606
That's great, but unfortunately my device is one step more screwed that others - no bootloader not even working Windows now.
Is there any way to boot directly from SD card?
victor,
can you upgrade or downgrade the bootloader ? If you can, HOW? please post the way to upgrade or to downgrade the bootloader. :shock:
ID64,
I had an XDA I and wiped the bootloader by accident. As far as I know, you have only two options. The first one is JTAG [http://www.xda-developers.com/jtag/] but I don't think the boards have been documented yet for XDA II. The other option is to bring it back to where you bought it from. Tell them there's something wrong with it and play dumb. If you're lucky they might replace it for you, if they assume that you are still within warranty.
Yes, there is a way to upgrade/downgrade the Bootloader. I just don't know how.
The bootloader is locked, that is the problem you have (except for those who cannot access the bootloader).
If you know the right syntax and use the password to the bootloader (it is BOOTLOADER), you can load the proper ROM back using the "LNB" command. However, they have changed the syntax since ITSME's doc on the subject, or he mis-documented the syntax to the bootloader. Or at least his syntax was wrong with 1.06 version.
I got mine fixed, but I have means available that 99.9% of the people out there do not have. If I knew more, I would tell you about the percise syntax in the bootloader -- but alas, I am not a developer.
Victor said:
Yes, there is a way to upgrade/downgrade the Bootloader. I just don't know how.
The bootloader is locked, that is the problem you have (except for those who cannot access the bootloader).
If you know the right syntax and use the password to the bootloader (it is BOOTLOADER), you can load the proper ROM back using the "LNB" command. However, they have changed the syntax since ITSME's doc on the subject, or he mis-documented the syntax to the bootloader. Or at least his syntax was wrong with 1.06 version.
I got mine fixed, but I have means available that 99.9% of the people out there do not have. If I knew more, I would tell you about the percise syntax in the bootloader -- but alas, I am not a developer.
Click to expand...
Click to collapse
Thanks for the reply, Victor. When you talking about commands for bootloder what connection to PC you are talking about? Serial or jtag?
I am referring to the device in the cradle, in bootloader mode. The screen in this mode should read "USB" on top and "V.1.06" (or whatever version) on the bottom. Very hard to read, as there is no backlight.
Anyhow, just for fun.... why don't you try the following:
Uncheck the USB option in Active Sync Connection Settings
Cold boot your system (hard reset)
place the device in the cradle
run the communications software (found on this forum)
When asked which COM port to use, click on the down arrow and see if there is a USB port listed (should be top entry in list).
If so... click it. (if not, you are basically done)
After clicked, then hit return (enter) on the pc a few times.
Anything happen?
Hello.
I have a problem I hope someone here can help me to solve..
I have an Orange SPV M3100 that hangs on the Windows Mobile screen when I try to start it.
I'm able to go into bootloader mode, and i have tried using mtty142.exe with the set 14 0 command. It still won't boot. I've also tried to hard reset it.. still won't boot..
What I did was trying to unluck the SIM-lock with the Universal unlocker (HTC_Uni_Unlock_v1) from buzz. At the time I thought universal meant that it worked on all HTC devices (stupid, I know)... And I also thought it was harmless to just try and see if it worked. But I got an error around 92-93% and after that my device won't start. So my radio ROM might be screwed.
I'd like to flash my ROM with the i-mate one (JASJAM_WWE_1.20.305.3_1.20.305.104_1.07.03.10_ship.exe) and then add the ext-rom. But how do I do that when I can just access the bootloader screen? And do you think it will boot again if I'm able to flash it?
Here's some more info about my device:
HERM100
IPL-1.01
SPL-1.04
Thank you very much in advance. Help will be highly appreciated.
No your rom *is* screwed. You can get into bootloader, you can even get to 11% of a dopod etc rom upgrade if you try, but you will not flash a new radio.
You CAN boot the device.
Do a hard reset, but do not press spacebar to reboot after. Instead, do a soft reset. The unit should boot but as you've screwed the radio you will not get a gsm signal and the phone will say unknown sim status.
I know this as I bought one cheap after the owner had done exactly the same as you.
IMEI-check's unlock solution is the only one that works IIRC, and in some cases this re-writes the security area of the phone and repairs similar issues, but in this case I could not get the prog to read.
You need to return the device to HTC - you'll need to pay approx £35 for reflashing back to the orange rom. This is what I had to do.
Currently you cannot book the m3100 in through the web as it's too new, instead email / call them.
http://service.htceurope.com/
edit - or if you're an orange customer ring 150 and act dumb saying it ' won't work'.... :wink:
Richard
What happens if you just leave the phone in bootloader mode and then try to flash any ROM (imate, dopod, htc...)? run 2 times the RomUpgradeUt.exe if you get an error on the 1st try.
If you get an error while running the rom upgrade utility you can monitor the USB port while upgrading (you will see the real error from the bootloader then), there's some more info on this wiki page:
http://wiki.xda-developers.com/index.php?pagename=Hermes_BootLoader
good luck
pof said:
What happens if you just leave the phone in bootloader mode and then try to flash any ROM (imate, dopod, htc...)? run 2 times the RomUpgradeUt.exe if you get an error on the 1st try.
If you get an error while running the rom upgrade utility you can monitor the USB port while upgrading (you will see the real error from the bootloader then), there's some more info on this wiki page:
http://wiki.xda-developers.com/index.php?pagename=Hermes_BootLoader
good luck
Click to expand...
Click to collapse
No, if you want to send it back under warranty do not try to run a rom update as there are no orange rom packages. As described in my post above, it will get to 11% and stop. The device will be in the same state as before, with the same ext rom, but the splash screen and bootloader will have changed.
i.e: it will be bloomin obvious you tried flashing it and failed. Not what you want if you try for a warranty repair....
There is no error from the bootloader - as there is no radio rom present and no security area the upgrade process just hangs.
Richard
fluffcat1 said:
No, if you want to send it back under warranty do not try to run a rom update as there are no orange rom packages.
[...]
i.e: it will be bloomin obvious you tried flashing it and failed. Not what you want if you try for a warranty repair....
Click to expand...
Click to collapse
That's true, do not try to flash any other roms if you want to use the warranty or send the device back...
Thank you very very much for your help guys.
As I'm the administrator of these devices in the company I work for I just grabbed a new SPV and will send this thing back to Orange. It sounded like I'm getting a new one..
Well, I think I've learnt my lession.
Oh, and I have another question. Is there a reg editor I can install on this one so I can remove the app lock? I know I can install java apps, but it's a bit grumpy about apps that needs installation (the developer must be certificated).
Cheers guys.
Hi,
Try to flash a new rom using the SD card method described here:
http://forum.xda-developers.com/viewtopic.php?t=62596
The rom must match your CID. Let us know if it works
pof said:
Hi,
Try to flash a new rom using the SD card method described here:
http://forum.xda-developers.com/viewtopic.php?t=62596
The rom must match your CID. Let us know if it works
Click to expand...
Click to collapse
Errr, did you read the last post? He sent it back......
Richard
I just wanted to let him know there's a possible solution, it just in case he still has the unit
pof said:
I just wanted to let him know there's a possible solution, it just in case he still has the unit
Click to expand...
Click to collapse
Maybe his search is broken as well as his old phone eh?.... :roll:
fluffcat1 said:
You need to return the device to HTC - you'll need to pay approx £35 for reflashing back to the orange rom. This is what I had to do.
Click to expand...
Click to collapse
Sorry to take the thread a bit OT, but just wanted to confirm this again.
So, if I flashed my M3100 with a different ROM, and then had to return the phone to Orange for repair for a different reason, I can send it back to HTC just to have the ROM reflashed, and then send the phone to Orange to get the repairs done?
I've been hesitating on whether to flash the phone with a non-Orange ROM because I didn't want to give up the ability to obtain warranty repair (as there is no ROM upgrade yet). If it's just a matter of £35 and then everything else as normal, maybe it's not so bad...
Thanks!
My SPV M3100 won't start!!!
I also did this, so if anyone can find a solution it would be greatly appreciated.
Also tried this and it didn't work for me:
Try to flash a new rom using the SD card method described here:
http://forum.xda-developers.com/viewtopic.php?t=62596
"I have a problem I hope someone here can help me to solve..
I have an Orange SPV M3100 that hangs on the Windows Mobile screen when I try to start it.
I'm able to go into bootloader mode, and i have tried using mtty142.exe with the set 14 0 command. It still won't boot. I've also tried to hard reset it.. still won't boot..
What I did was trying to unluck the SIM-lock with the Universal unlocker (HTC_Uni_Unlock_v1) from buzz. At the time I thought universal meant that it worked on all HTC devices (stupid, I know)... "
rachelm700 said:
I also did this, so if anyone can find a solution it would be greatly appreciated.
Also tried this and it didn't work for me:
Try to flash a new rom using the SD card method described here:
http://forum.xda-developers.com/viewtopic.php?t=62596
"I have a problem I hope someone here can help me to solve..
I have an Orange SPV M3100 that hangs on the Windows Mobile screen when I try to start it.
I'm able to go into bootloader mode, and i have tried using mtty142.exe with the set 14 0 command. It still won't boot. I've also tried to hard reset it.. still won't boot..
What I did was trying to unluck the SIM-lock with the Universal unlocker (HTC_Uni_Unlock_v1) from buzz. At the time I thought universal meant that it worked on all HTC devices (stupid, I know)... "
Click to expand...
Click to collapse
the above link doesnt work?
zohaer21 said:
the above link doesnt work?
Click to expand...
Click to collapse
IIRC it is this link on the new forum:
http://forum.xda-developers.com/showthread.php?t=277281
spv m3100 don't start
hello guys
I have the same problem about spv m3100. I used "universal unlock tool" to unlock my device and now it don't start,don't boot...I tried the Hermes SD Card flashing methods with qtek001 rom and, a white screen with "loading...." appears for 2 second and then nothing else appened. I think that the method is right but I need to use a different software. what do you think about?
please help me
thankksssss
My SPV M3100 won't start
SD card method is no good as there is no upgrade from Orange until January.
Tried to do a radio upgrade explained here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms
But it didn't work just came up with connection error, tried to monitor USB but nothing showed up to find out why, althouth mtty commands always do show up in USB Monitor.
Still have a brick and looking for a solution, hopefully, someday, please someone help me I am loosing my mind.
Hello
How to enter boot mode on HTC 200 ?
My htc hangs on HTC screen.
I'm trying to reflash it.
Thanx
Chris
@chrisro, Please read the wiki:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
http://wiki.xda-developers.com/index.php?pagename=Hermes_Resets
Thank you very much.
Greets form Poland !
Chris
Hi
I was given an Orange SPV M600 running WM5.0 I foolishly thought I would be able to unlock it to work with my T-Mobile sim (the only network I can get coverage at home) I ran an unlock tool from en.pdamobiz.com
http://files.pdamobiz.com/c/PDAMobiz.com_ProphetAKU2_unlockCID.rar
I managed to get to through to the completion of the Downgrade.bat process. I was then asked to sofdt boot the M600 but it now cannot be found by Activesync. I was unable to successfully run Unlockcid.bat and now it just boots to either the 'Orange' screen (displaying IPL 2.10.0001, SPL 2.10.0001, GSM 02.07.20 & OS 1.0.13.21 - the new OS I believe) or the 3 colour screen (displaying IPL 2.10.0001, SPL 2.10.0001) if I hold down the camera button.
Windows 5.0 has gone or is unreachable but I am assuming it can't be completely dead as I get a noise when connecting/disconnecting the USB lead....
Is this false hope? Have i killed it after 2 days of ownership??? Should I have attempted this process with very little tech knowledge - me thinks YES!
I would be eternally greatful to anyone who can help me out of this black hole..... I just need pointing in the direection of what stage the M600 is at and how to get it running on my T-Mobile sim.....
Thanks in advance
hi there, try going into the bootloader screen, when you connect the usb cable it should show on the bottom off your screen. then try uploading the orange rom you can find on the wiki page. if this works then try using the loki unlocker which you should also be able to find on the wiki page. i used the loki tool and it unlocked first time. hope this helps. let me know how you go.
The GOOD news is No you haven't killed it. It seems you have wiped the operating system from it. I would sugest searching for RUU-Prophet-G4-AKU2.2-2.20-2.47.21-Jester-r1.exe down load it and then get your phone to the multi colour screen before running the download. This should then update your phone
when I tried to unlock my phone, I couldn't get it to unloack at all till I put a orange pay as you go sim in the phone and registered the sim with orange then it unlocked first time.
Killed prophet reborn!!
Fingers666 said:
hi there, try going into the bootloader screen, when you connect the usb cable it should show on the bottom off your screen. then try uploading the orange rom you can find on the wiki page. if this works then try using the loki unlocker which you should also be able to find on the wiki page. i used the loki tool and it unlocked first time. hope this helps. let me know how you go.
Click to expand...
Click to collapse
Spot on. Thanks so much for the advice. Fingers666 & jazpa !! I'm back on track. M6000 is now communicating again. WM5 is resident. Just need to unlock the sim and I'm away. [email protected] tried loki 3.0 amd 3.0a with both Activesync 4.2 and 4.5 respectively without any luck so I've just spent £5 a http://www.unlocking.org.uk/ as they say they can unlock a G4 ver. We shall see!! Great help though and THANKS again to both of you
Please Help Meee!!
Hello i was wondering if anybody could help me.
I want to unlock my orange SPV M600 for free.
If there are any safe and free websites that anybody knows of could u please tell me.
Thank Youu!!
James Thomas
Download Lokiwz, it is quite easy to locate. Inside the folder you will find 1 or 2 cab files, copy these to your storage card and run them on your M600. Now run Lokiwiz from your PC, after around 12 minutes, it will display your sim unlock code. Switch off your M600 and insert the sim you want to use, at the prompt, enter your code lokiwiz generated. For around 2 minutes the phone will seem to have no signal, then it will connect.
Worked first time for me, my M600 was locked to Orange, now it works great with O2.
wonderful works great with G4
thanks
mike
i saw lot of people have dead prophet problem, so i am here now to make a new thread to all this people and i hope to make it useful.
now we start
** FIRST : lets know names of prophet :
I mate Jamin, O2 XDA Neo, Qtek S200, Dopod 818 pro, Dopod 830, SPV M600, VPA Compact S.
** SECOND : we must know that before we trying to do any updating or change roms on my prophet i just need to do which called unlock for the prophet and then we after that been able to change any rom on my ( jamin ) and of course u need to be careful about Your device is it G4 or G3 ,
# and how we know its G4 Or G3 ?
# when u start Your Device u will see some numbers on left,
---------------------
IPL: 1.00.000
SPL: 2.20.000
GSM: 02.61.21
OS: 3.0.0.0
--------------------
and may be changed and that goes to the rom which You have, now we look for the last number on ( IPL and SPL ) , if we found it ( 0 ) it means You r G3 and if it ( 1 ) so You r G4 .
** THIRD : lets go to unlock , i will put programs in this thread it will help u in unlock.
-- Sync your device with computer and open the file u download it called HardSpl you will find two files one one foe G3 and G4 open your kind then you'll find a file called (( hardspl.bat )) okay, be sure your device is connected to computer then open the file and follow instruction and it will reset your device ,
now u ready to change rom.
TO BE CONTINUED
hey guys
i tried to attachment the file now put it gives me database problem, so i will be after it to attach don't worry pals. see you later.
hey guys
i tried to attachment the file now put it gives me database problem, so i will be after it to attach don't worry pals. see you later.
if any one can help please contact me.
hello
my device is jamin g4
it stopsat the boot loader and dono thing
can u help me please?
my e-mail is [email protected]
and suddenly after trying to update the spl been 1.01
please help me
can i fix it?
waiting for ur help
What is the IPL and SPL?
If the wiki where up, I'd suggest looking at that, but as it is I'll explain it now...
What ROM where you attempting to upgrade to?
To get the device back, I would say "Read the wiki" but it's down!!!
Download this ROM.
In ActiveSync, disable "connect through USB" (File->Connection Settings).
Put the device into bootloader (the three coloured screen) and connect it to the computer using the USB cable.
Run the file you downloaded earlier. This should then install a new ROM.
From there, just wait for it to finish.
Now, it should work!
From there, you could re install the Orange WM5 ROM, or try upgrading to WM6. Make sure you read all the relevant guides first!
thanks alot i did as u said but it stops at 80% or 88%
then show this message (error 326 invalid command )
please help me
i'm feeling bad
my mail is [email protected]
What brand the device? Has it been SIM unlocked?
hi again brothers, pal zerocool. first u must unlock ur device to be able to accept any rom after that and solve pproblems.
first flash this rom its offecial and it solve dead prophet problems.
then make hard spl by program open file called hardspl.bat.
make hard reset.
flash ur rom u want.
make hard reset again.
then enjoy.
i uploaded the hardspl program but i couldnt upload the rom its so big so u can look in ur mail u will find the solution.
u can extract file by any program for zip.and tell me the news
dont forget to look to ur mail. see all of u later
Dead prophet
Hi guys,
I have been using a sh... Nokia sine I broke my prophet G4 in december by upgrading the OS.
I had downgraded first to NVID and then I tried to upgrade and it fails at 95%.
Sine this day, my prophet seem totally dead, no light when plug on both charger or computer, windows do not recognize at all the device because it is turned off. And it really do not seem to charge...
I am living in China now and a guy told me I had to change the PB board...The ost is 100Euros, but I am almost sure I an find another solution...
The weird thing is I cannot charge it at all ( I mean no lights but does it charge a little?).
The guy tested my prophet with another battery and in that ase, it is stuck on the bootloader.
We tried several roms and it always fails at 95% and the error is 200 something, maybe 245 or 243, I do not remember sorry...
Is my phone hardware is dead? or it is just a software problem and I did not see the right guy?
Do I need to buy a new battery? I have read that sometimes the device is not able to recognize it even if it the offiial one and even if it is working on another device...
PLease help me I don't want to loose this phone that I've been using for almost 3 years...
Otherwise I will switch to an iphone but I am not sure to be as happy than I was with my prophet.
Xie Xie for your advice and answers.
Guilh1
Can it enter bootloader at all?
If yes, what are the IPL and SPL?
If not, it will be a hardware problem (may just be connectors to the battery but may be something more).
the only way of recovery is using jtag
but 1st we must discover the location of jtag pins on motherboard
I just do not know because with my actual battery, anything is possible....
when I tried with the guy and a new battery it was blocked on the bootloader, but don't remember the IPL and SPL...sorry
I may be right about the battery onnectors though, but the problems seem to be from the phone connectors or the battery it self???
Thank you anyway for your very quick reply
when I tried with the guy and a new battery it was blocked on the bootloader, but don't remember the IPL and SPL...sorry
Click to expand...
Click to collapse
If it can enter bootloader, it is almost certainly your battery at fault!
Ok so i burnt my battery during the upgrade...
But why is it still blocking at 95% when he tried to put a rom?
With his battery, it was stuck on the bootloader and not possible to install a rom, even a NVID WM5...
I really do not know what to do...
Thanks again for your help
My iMate JAMin is dead; I was in the middle of flashing it when it froze, now when I turn it on, I get the Tri-color screen with the following ...
IPL: 2.13.0001
SPL: 2.13.0001
No [BUSB[/B] is detected. So now I need a way to flash it from the SD Card. I can not even see the HTC startup screen anymore, it just jumps directly into the tri-color screen.
Ok so i burnt my battery during the upgrade...
But why is it still blocking at 95% when he tried to put a rom?
With his battery, it was stuck on the bootloader and not possible to install a rom, even a NVID WM5...
I really do not know what to do...
Thanks again for your help
Click to expand...
Click to collapse
Do you know which ROM? Is your device branded, and is it SIM locked?
Do you know the IPL/SPL? Did they end with the same numbers?
My iMate JAMin is dead; I was in the middle of flashing it when it froze, now when I turn it on, I get the Tri-color screen with the following ...
IPL: 2.13.0001
SPL: 2.13.0001
No [BUSB[/b] is detected. So now I need a way to flash it from the SD Card. I can not even see the HTC startup screen anymore, it just jumps directly into the tri-color screen.
Click to expand...
Click to collapse
Please look at this if you want more help, post here...
thanks alot dear samuraititio
but i can't flash it
it writes (no vender id)
help me please i tried another tool with the same nbf file it stops at 80%
and it automatically enter the boot loader
and i can't do ant thing
its information
jamin/g4
ipl 2.13.0001
spl 1.01
i think my problem is in the spl coz it was 2.13.0001
and now it's 1.01
how can i fix it please i still starter in this way so i'm trying;
help soon please
You now have a G3 SPL on a G4 Device.
What did you flash exactly?
l3v5y said:
Do you know which ROM? Is your device branded, and is it SIM locked?
Do you know the IPL/SPL? Did they end with the same numbers?
Please look at this if you want more help, post here...
Click to expand...
Click to collapse
hello pal i3v5y
i have the same problem
idid what u said the flashing stops at 80%
i need ur help please
i'm online at the moment and u too help me soon if u can please
my e-mail is [email protected]
waiting for u i don't have any other device to use and i need it
l3v5y said:
You now have a G3 SPL on a G4 Device.
What did you flash exactly?
Click to expand...
Click to collapse
now i flashed the official rom of jamin but it stopped at 80%
Hello Everybody,
My mobile at&t 8525 alias HTC 8525 is stuck in windows operator logo.It would not boot further. It happened while I tried to upgrade it from Windows 5.0 to Windows 6.0.First I got a tri-colour screen,but in a hurry I tried to backgrade to windows 5.0 again.
Other problem the mobile cannot be synced. I have installed Microsoft Active sync 4.5. Even then it could not be synced.
I tried to read all the posts ,but could not understand anything.
So please help me in getting my mobile repaired
Don't worie.
I had somewhat the same issue with a bad ROM flash.
Just disconnect the USB and boot to the bootloader screen (the tricolour screen) and you should be able to reflash the phone again.
Problem in syncing the mobile
I am not able to sync the mobile to the laptop.I have installed Microsoft Active sync 4.5. Even then it is not syncing.So how could I run the hermes upgrade if the mobile is not helping.
Please help
In Activesync on PC - Untick "Allow USB Connections".
Put the Hermes into bootloader (tri-colour screen) and connect by usb. Run the RUU_Wrapper.exe file you want. Follow onscreen instructions.
You need to have installed Hard SPL V7 for this to work...
did not work
Hello Boss
I tried to follow the procedure you suggested me. but it did not work. I tried with Hard SPl 7.0.
Please give me some suggestion
you dont need an active sync connection to flash it. Enter bootloader(tri colour screen) as you were told in the previous posts and Just click on the boxes that you do have a connection(even though you dont) and then flash the rom.
@ultramag69 i hve never had to untick allow usb connections and i have cocked up loads of rom flashes, saying that i have never had a problem flashing in vista either so maybe i am lucky
If you still cant flash doing it this way, then maybe you should try flashing from sd card instead, just make sure the battery is fully charged. Full instructions of how to do this are found in the hermes wiki, which i advise you to read anyway.
Oh and good luck anyway, you should be able to recover the phone from this ,so i wouldnt fret too much
Guess he isnt hardspl'ed... then his batt is death... must to flash a shipped rom.
correct me if im wrong.
Problem with upgrade At&T 8525 mobile
Hi!
I'm having problems with my Cingular 8525, after I made the upgrade to WM6.1 (FARIA-R32-XDA2_WM6.1.rar) for WM 6.5 (FCWs_stock_like_6.5_v3.rar), and slowed my device does not work anymore. He died.
I need help please. How resurrect it?
Excuse my English.
english is not the problem here cause we need more info... device info SPL IPL hardSPL? you go from 6.5 to 6.1?
Do you try to flash first the Stripped?
Does your batt has charge enough to boot?
There are many many things to say so... start to tell us all your history!
Hi
I tried to Hard spl with Hard Splv7. But I got a error. I even tried the Sd Card method.Its says loading and I get the tricolour mode. If I press the Power button its not showing the status of upgradation.
Where can I get a shipped rom. Actually my Spl is 1.11.
Hi
I tried to Hard spl with Hard Splv7. But I got a error. I even tried the Sd Card method.Its says loading and I get the tricolour mode. If I press the Power button its not showing the status of upgradation.
Where can I get a shipped rom. Actually my Spl is 1.11.
check the wiki pages for your device in the upper bar of this web forums
there are many official roms.
I also am currently using an 8525 (Herm100). It was received from an Ebay deal with WM5. I flashed it with the ATT OEM WM6pro (aka shipped wm6). Once it hit the three color boot screen, it sat on that for a couple of minutes then started cooking. Once it showed a progress bar, it took about 3 minutes to cook the WM6 over the WM5. It also showed a popup that stated going back to WM5 was not an option.
I would suggest running the installer again and going down to 7-11 for a refreshment. You may not have let it percolate long enough to set itself up for the actual ROM overwriting.
gorkalraghavendra said:
Hello Everybody,
My mobile at&t 8525 alias HTC 8525 is stuck in windows operator logo.It would not boot further. It happened while I tried to upgrade it from Windows 5.0 to Windows 6.0.First I got a tri-colour screen,but in a hurry I tried to backgrade to windows 5.0 again.
Other problem the mobile cannot be synced. I have installed Microsoft Active sync 4.5. Even then it could not be synced.
I tried to read all the posts ,but could not understand anything.
So please help me in getting my mobile repaired
Click to expand...
Click to collapse