Hi,
i have a very big problem with my XDA (HTC Prophet).
I already had a WM6.1 Rom on my device but wanted to change to a different rom.
Now my Device is showing me the RGB screen after upgrading. The UpdateUtility works fine and i get "update successful" after the updating.
Now i can just install the original rom from O2 (WM 5).
Does anybody know a solution for my Problem?
Thanks and Greetings
MrDCA
Can you get the device to start up after installing the WM5 ROM?
What you will need to do is follow this to recover it: http://wiki.xda-developers.com/index.php?pagename=Prophet_recovery
And then HardSPL before flashing a new WM6.1 ROM.
Thanks a lot l3v5y.
But there is still a problem. If i want to HardSPL my device i get an error.
Error 208: File Open
The update Utilite can not open the requested file. Please Check your update utility.
My SPL is 2.15.0001 so i have G4.
Sometimes i get this weired message:
Error 300: Invalid Update Tool
This update tool cannot be used for your PDA Phone.
Please get newer Update Utility.
mrdca said:
Thanks a lot l3v5y.
But there is still a problem. If i want to HardSPL my device i get an error.
Error 208: File Open
The update Utilite can not open the requested file. Please Check your update utility.
My SPL is 2.15.0001 so i have G4.
Sometimes i get this weired message:
Error 300: Invalid Update Tool
This update tool cannot be used for your PDA Phone.
Please get newer Update Utility.
Click to expand...
Click to collapse
Would you like to try my tool? (@ my signature~~, hope it works for your situation... )
You're using prophet tools? I think there is a slight issue with that, but I've fixed it and shall upload it now...
I tried both utilities.
none of them works for me.
Let me know if you uploaded the fixed version and i will test it!
Thank you guys!
The fixed version is now uploaded in the Prophet Tools thread. If that fails, you can use the HardSPL utilities from the New WM6 Upgrade guide.
Related
I'm hoping you folks can help me out. I have tried to upgrade my XDA2 using the Himalaya_WM2003SE_Upgrade but it keeps coming up with:
"Error 150:ROM UPGRADE UTILITY ERROR.
This ROM upgrade utility does not design for your device.
Please get the proper ROM upgrade utility and try again!"
I've got:
FCC ID: NM8HIMALAYAS
IMEI : 351938002885560
Now the unit just gets to the bootloader "SERIAL, v1.06" until I put it in the cradle and it goes to "USB, v1.06". I ran the upgrade following the instructions to the letter but no joy! Am I using the incorrect upgrade utility as the error message says or am I missing something? Any help to restore my XDA2 will be gratefully received!!!
Thanks again!!
which rom are you tryin to upgrade to and provided by who ???
regards
jeetz
I'm basically trying to upgrade my O2 PH10B XDA2 to anything that works! It seems whatever I try, it stays on the bootloader screen with either "Serial or USB" on the display depending whether it's in the cradle or not. I can't do anything with it. I've tried to use the "Himalaya_WM2003SE_Upgrade" utility but as I said, it just tells me that this is not corrrect for my device.
HELP!!
Thanks :roll:
try to reset your device and run himalaya upgrade again
I tried it soooo many times but I still get:
"Error 150:ROM UPGRADE UTILITY ERROR.
This ROM upgrade utility does not design for your device.
Please get the proper ROM upgrade utility and try again!"
I've even tried the O2 Xda_II_172181_Final utility but I still get the same thing. Why does it say it is not designed for my device when I have an O2 Himalaya? If anyone can help I will pledge my undying admiration and possibly even lay down my life for them if required! (sorry, that should have read "wife", not life!) :lol:
glt56 said:
I tried it soooo many times but I still get:
"Error 150:ROM UPGRADE UTILITY ERROR.
This ROM upgrade utility does not design for your device.
Please get the proper ROM upgrade utility and try again!"
I've even tried the O2 Xda_II_172181_Final utility but I still get the same thing. Why does it say it is not designed for my device when I have an O2 Himalaya? If anyone can help I will pledge my undying admiration and possibly even lay down my life for them if required! (sorry, that should have read "wife", not life!) :lol:
Click to expand...
Click to collapse
http://forum.xda-developers.com/viewtopic.php?t=15382&highlight=
try mysterman rom from here dont go for himaupgrade and stuff try to run the setup direct with default radio ....
Success!!!!!
Finally managed to get my XDA2 back to life after some severe CPR & Mouth-to-mouth, and WM2003SEO2UKv2.rar. Thanks for all the suggestions and help.
I also now have a dead M1000.
Where did you get your rom that worked from?
Can you post it please?
Thanks
R
plsssssss help me i also have same problem plsss tell me how u get that pls
Dear friends
I was tring to upgrade my iMate Pocket PC also know as Himalaya with windows2003 SE , while upgrading I faced problems, the upgarde failed and now I am just getting no display and OS too. The only message displayed is
Serial
v1.03
nothing is working please help
bye with regrads,
your unit is still okay; even better that the usb version is showing on the screen. it's simply stuck on bootloader mode. what kind of problems did you encounter resulting in the failed upgrade?
one suggestion i can give before you downgrade is to try and proceed with the upgrade to se. put your unit back on the cradle but don't expect activesync to "recognize" the device. just put it back on the cradle and rerun the upgrade to se.
same thing happened when i upgraded but to wm2005. the screen showed error and the only thing on the screen was the usb version. i simply cradled back the unit and ran the upgrade. worked.
cheers
Hi
Thanks a lot, i tired those steps before and even now I did but its not upgarding I am gettig following error as show i the attachment. Please let me know what to do
thanks a lot
yas
oh, it appears that you have the "wrong country" id issue. i'm not entirely sure as to how to avoid this but i believe it has something to do with the correct rom version (guys, correct me if i'm wrong). where did you get the rom you used for upgrading to se? downgrading might be the only trick if there is no rom for saudi-based users...but if any chaps presently living there and were successful in upgrading their units perhaps you could share the rom version/s you used?
cheers
yasirirfan said:
Hi
Thanks a lot, i tired those steps before and even now I did but its not upgarding I am gettig following error as show i the attachment. Please let me know what to do
thanks a lot
yas
Click to expand...
Click to collapse
To overcome the Country ID Error, first you need to install this tool...
ftp://xda:[email protected]/Tools/ER2003Edit_1_4_26.zip
Open the ROM file you want to upgrade, then change the appropriate 'Operator ID' code, after this click 'Save ROM image'.
Upgrade ur device. You will no longer face the error message.
I have a tmobile g4 wizard.
when I tried flashing it either:
a. gives me a old utility error
then i get the newer italian 2.5.2 utility to flash with.
b. no matter what rom i use (I tried molski's 3.3 and crossbow reloaded 1.7 = both are without ipl/spl)
the utility seems to update, and then gives me an error at 99%. it doesnt crash, it gives an error
then i have to flash it back to tmobile or wizard love to get this working.
any idea guys ?
yeah, put your device into bootloader mode before you start the RUU.
doesnt help.
again meter progresses to 99% where it turns red and then the application on the pc gives me an error.
firewalls / antivirus are turned off too.
Hello i had the same problem while updating to wm6 my qtek 9100, here is the solution: downnoad the Wizard_Love rom, t is already patched so it works on your g4, Read g4.3 Here http://forum.xda-developers.com/showthread.php?t=310831&highlight=Wizard_Love
First off have you CIDunlocked your device before you flashed?
I was having the same problem with my phone yesterday. I thought i actually bricked it when trying to flash it. Eventually i had to use the rom from the htc website and then use ShellTool from the sticky in this forum. Finally i got wm6 loaded with its help.
Good luck!
So i wanted to flash my cingular 8125 to windows mobile 6, so i downloaded this:
(BIG MISTAKE)
http://www.tradebit.com/filedetail.php/2559279-Software-Programs-Cell-Phone-Programs
and i followed the instructions and after i hard reseted my phone, it booted to a white screen. I have tryed reflashing, going into bootloader mode and reflashing, and i nothing helps.
can one of the experts on this forum please help me???!!!
thanks
i need help assap!! lol
i dont care even if i flash back to winmo5, I JUST WANNA UNBRICK
dahdout said:
So i wanted to flash my cingular 8125 to windows mobile 6, so i downloaded this:
(BIG MISTAKE)
http://www.tradebit.com/filedetail.php/2559279-Software-Programs-Cell-Phone-Programs
and i followed the instructions and after i hard reseted my phone, it booted to a white screen. I have tryed reflashing, going into bootloader mode and reflashing, and i nothing helps.
can one of the experts on this forum please help me???!!!
thanks
i need help assap!! lol
i dont care even if i flash back to winmo5, I JUST WANNA UNBRICK
Click to expand...
Click to collapse
What IPL/SPL it displays now ? ,Does it get into Bootloaders ? if it still does than download and flash 'wizard_love_rom' hope it'll recover back.
RE:
It just boots into a white screen. If i hold the camera and power buttons together it boots into bootloader mode, and says USB in the bottom corner. (when i am conncected via usb) but the problem is that active sync doesnt recognize it in bootloader mode. I have tried flashing it in many different ways and i have had no success.
When i go home i will try wizard_love_rom.
and as for the IPL/SPL, i will also check that when i get home.
Where can i download the wizard_love_rom?
Thanks for the help !
RE:2
Hello,
Mr IPL and SPL are both 2.25.0001
My GSM: 02.25.11
My OS: 2.18.0.0
Good News
So, I flashed my phone with the "Wizard_Love_2.26.10.2_WWE_Novii_CF2.rar"
which i found the download for over a quick google search, and now i want to update to winmo6 or 6.1.
Can you send me the link for the easiest way to do it on a G4 cingular 8125 (HTC Wizard.)
I have never CID unlocked, which was probably why i got the white screen earlier. but do i need to do it know that i am on the wizard love rom?
please help,
thanks
dahdout said:
So, I flashed my phone with the "Wizard_Love_2.26.10.2_WWE_Novii_CF2.rar"
which i found the download for over a quick google search, and now i want to update to winmo6 or 6.1.
Can you send me the link for the easiest way to do it on a G4 cingular 8125 (HTC Wizard.)
I have never CID unlocked, which was probably why i got the white screen earlier. but do i need to do it know that i am on the wizard love rom?
please help,
thanks
Click to expand...
Click to collapse
Glade its working again !
You got a G4 device,it cannot be CID unlocked,but however,it can be upgraded to wm6 or 6.1,read the methods 'HardSPL' or 'SoftSPL' posted as stickies in the G4 forum for upgrading to wm6 or 6.1.
re:3
thanks, you really saved me with your help!
dahdout said:
thanks, you really saved me with your help!
Click to expand...
Click to collapse
Thanks !
Glade you got it working
sorry, but i need help... again
Ok,
I know that this may be getting a little annoying for you and im sorry for that, but i need your help on this. I am currently running the wizard love rom. And I have Hard SCP'd.
I have to problems:
1. My EDGE doesn't work, i only get GPRS speed data.
2. I can't upgrade to any new rom..... i always get "ERROR [300] Get a newer update utility!"
How can I fix both of these problems?
I have searched forums and google and nothing has come up.
dahdout said:
Ok,
I know that this may be getting a little annoying for you and im sorry for that, but i need your help on this. I am currently running the wizard love rom. And I have Hard SCP'd.
I have to problems:
1. My EDGE doesn't work, i only get GPRS speed data.
2. I can't upgrade to any new rom..... i always get "ERROR [300] Get a newer update utility!"
How can I fix both of these problems?
I have searched forums and google and nothing has come up.
Click to expand...
Click to collapse
ok,for error (300)you can use the RUU MUNS already posted in the 'HardSPL' thread,download the RUU_MUNS application extract it to a folder and copy and paste all the files of this extracted to the folder of the Rom replacing all the RUU files in that folder or copy the nk.nbf folder in the Rom to the extracted folder of the RUU_MUNS and then run the RUU,it will start to flash and complete and hopefully fully boot up.
For edge or gprs,you'll have to get network settings of your network carrier or check out the thread from where you downloaded the rom,its uaually posted there or check out the 'Network' thread.
Aquestion to Zabardast_1 ?
294 error , invalid vender ID
what does that means & asolution to it during rom update
ERROR [294] : INVALID VENDER ID
One of these error messages will appear when you use the wrong RUU to do the upgrade. RUU will check if the Model ID and Language ID are compatible with the device. Make sure you use the appropriate RUU tool to upgrade.
HI THERE,
I AM USING WM 6.0 WITH SPL 1.1. THE PROBLEM IS THE ERROR 270.
WHENEVER I TRY TO UPGRADE MY ROM TO WM6.1 OR WM6.5 OR EVEN WHEN I TRY TO UPGRADE MY RADIO TO VERSION 1.57, THE MOBILE SIMPLY GOES TO BOOTLOADER AND AFTER COMPLETING JUST 1% , IT RESTARTS AND THE PC SHOWS "ERROR 270 [UPDATE ERROR]- THE IMAGE FILE IS CORRUPTED. PLEASE CHECK YOUR UPDATE UTILITY".
I HAVE TRIED DOING HARD RESET BUT OF NO USE.
EVERYTHING ELSE (LIKE CALLS, GPRS, GPS) IS WORKING FINE. BUT I CANNOT UPGRADE THE ROM.
ANY SUGGESTION TO PREVIOUS POSTS OR NEW SOLUTIONS IS NEEDED.
ERMANO.ESTE said:
HI THERE,
I AM USING WM 6.0 WITH SPL 1.1. THE PROBLEM IS THE ERROR 270.
WHENEVER I TRY TO UPGRADE MY ROM TO WM6.1 OR WM6.5 OR EVEN WHEN I TRY TO UPGRADE MY RADIO TO VERSION 1.57, THE MOBILE SIMPLY GOES TO BOOTLOADER AND AFTER COMPLETING JUST 1% , IT RESTARTS AND THE PC SHOWS "ERROR 270 [UPDATE ERROR]- THE IMAGE FILE IS CORRUPTED. PLEASE CHECK YOUR UPDATE UTILITY".
I HAVE TRIED DOING HARD RESET BUT OF NO USE.
EVERYTHING ELSE (LIKE CALLS, GPRS, GPS) IS WORKING FINE. BUT I CANNOT UPGRADE THE ROM.
ANY SUGGESTION TO PREVIOUS POSTS OR NEW SOLUTIONS IS NEEDED.
Click to expand...
Click to collapse
Hi you need to unlock the phone
read the beginners guide in the sticky for WM6 section
Read first then flash
How to get mac address
lakeman said:
Hi you need to unlock the phone
read the beginners guide in the sticky for WM6 section
Read first then flash
Click to expand...
Click to collapse
Thanks alot lakeman for ur help.
SOLVED OUT THAT ISSUE, BUT FACED A NEW ONE.
I M STUCK AT BOOTLOADER SCREEN WHILE TRYING TO INSTALL WM6.5.
BUT I FIGURED OUT A WAY BY USING MAC AND MTTY FORMAT.
BUT I DONT KNOW HOW TO GET MY MAC ADDRESS WHILE THE ONLY THING I CAN ACCESS IS THE BOOTLOADER SCREEN?
IS IT PRINTED SOMEWHERE ON MY DEVICE OR MANUALS OR IS THERE ANY SPECIFIC COMMAND FOR THAT?