I try to flash rom ENG to my NIKi
my version is 1.31.406
I read post "Nike SSPL, USPL and HardSPL" by jockyw2001
1. download the attached files
2. REMOVE SIM and SD CARDS !!
3. connect usb cable
4. copy sspl-1.16-nike.exe to your device and run it (usb cable must be connected!)
5. after a few seconds "USB" appears on the display
6. unplug and replug the usb cable
8. you can now flash the hardspl-1.15mfg-nike.nbh by running ROMUpdateUtility.exe from flash-uspl-niki
******* but it's still 0% and still boot loader screen*****
I Hard reset my NIKI but still bootloader and show
NIKI100
SPL-1.16.0000
CPLD-4
I try to flash this rom "RUU_Nike_HTC_WWE_1[1].13.405.01_Radio_Nike_1.58.11.07_signed_Test.exe"
It's 1% only and report error 262
"ERROR [262, 276, 284, 302] : UPDATE ERROR
This error occurs during the CE ROM code upgrade process.
Solution: If this happens, you can just soft-reset the device and run RUU again. The update process will then continue."
How to repair this
in post "http://forum.xda-developers.com/showthread.php?t=387217" by NetrunnerAT
"1. Download MTTY and connect via USB (dont forget do disable Activ Sync!!) us command Boot, to force a OS Boot!
2. After OS is Started ... Download SSPL and Copy it to your Phone ... please remove SD Card and SIM ... Start this Program!
3. Now you are in the Bootloader but it tells something about SPL 1.16Jump ... now you can Flash Hard SPL!!! If you doesnt see 1.16Jump you CAN'T Flash HardSPL!!
4. Now you can Flash my Dumped TIM Rom!!! "
I try this It show log
"boot
Fill RSVD information for block 288 to 309
Storage start sector=0xAF00, total sector=0x103C0
Storage start block=721, total block=1039
Total Bad Block in CE: 0
Erase physical block from 1011 to 2032
si backup: Erase physical block from 2032 to 2048
Card inserted
SDHW_EnablePowerOn
SDHW_ConfigGPIO
Cmd5 CMD_TIMEOUT
Cmd8 CMD_TIMEOUT
SD Init OK
SDFATChkConf: RhOpenFile() failed NIKECONF.txt
OEMGetUpdateMode
OEMTranslateBaseAddress 23 80000000 80000000
IPLMSG:0x8:INFO: Loading image ...
IPLMSG:0x9:INFO: Jumping to image...
OEMLaunchImage 80000000
Jump to Physical Address 10300000"
and still boot loader
how to fix it's
Thank' for reply
Please tell us ... what you have done before ... step by step!!!!
If you stay in the Bootloader and MTTY "boot" doesnt work, try the oemsbl with the command "cego"
NEXT ... what NIKI you have? German? UK? TIM? Vodovone branded?
You tell us not enough, too help you!
NetrunnerAT said:
Please tell us ... what you have done before ... step by step!!!!
If you stay in the Bootloader and MTTY "boot" doesnt work, try the oemsbl with the command "cego"
NEXT ... what NIKI you have? German? UK? TIM? Vodovone branded?
You tell us not enough, too help you!
Click to expand...
Click to collapse
Sorry For My Eng = =' I'm Thai girl.
I can't Remember lang before flash becouse I don't Know ^ ^ GER or Italy or Rus Lang
It's Not Eng Lang not Vodafone Brand
I'm new bie for this model . I have Dopod 818 pro It's Easy to flash I think Niki Is same
command "cego" notwork
Can I reflash any Office Rom?
What is SPL-1.16.0000 mean It's Hard SPL,SSPL or USPL
I Try to Put camera button and power button
and Use Mtty
boot
InitDisplay: Display_Chip=1
Card inserted
SDHW_EnablePowerOn
SDHW_ConfigGPIO
Cmd5 CMD_TIMEOUT
Cmd8 CMD_TIMEOUT
SD Init OK
SDFATChkConf: RhOpenFile() failed NIKECONF.txt
OSSIReadBack ++
Read SI data from flash success
tail signature match
Checksum match
UserStorageSIPreload ++
My NIKI Can boot and Use Now
I don't Know what Lang
" A Propos de
Windows Mobile 6 Profesional
Processeur : MSM7200-400Mhz
Memorie :101.67 Mo
Conecteur d'ext. :En cours d'utilisation
Informations de L'appareil
Version de Rom :1.31.406.09
Date de Rom :10/30/07
Version de Radio 1.58.16.27
Version de prot.. 25.61.30.03w
Is lang France?
@^ ^@
Hoorayyyyyyy
My phone is back
many thank's for NetrunnerAT
1. Download MTTY and connect via USB (dont forget do disable Activ Sync!!) us command Boot, to force a OS Boot!
2. After OS is Started ... Download SSPL and Copy it to your Phone ... please remove SD Card and SIM ... Start this Program!
3. Now you are in the Bootloader but it tells something about SPL 1.16Jump ... now you can Flash Hard SPL!!! If you doesnt see 1.16Jump you CAN'T Flash HardSPL!!
4. Now you can Flash my Dumped TIM Rom!!! "
and Now I Use rom TOM_Niki-Project_WM6[1].1_WWE_16keys_signed_Ship.exe
Many many Thank For XDA - Developers
http://www.pdamobiz.com/ <- its a Thai PDA Board!
The most errors on HTC Niki are simulare with HTC Polaris and HTC Kaiser!!!
I hope this helps!
my touch dual is lock at 3 color mode
Sorry for my english....
My niki is locked afther flash for unlock it (supercid)
I've tried to install a sspl and hardspl, but all have crashed at 95%
I've tried to install hardspl renaming the file nbh in NIKEIMG.nbh from sd, but this procedure have only send me message: loading......... and nothing all.....
At this moment my niki is stopped at 3 colors mode
Have you any idea for help me?
Many thanks to all
don't have any idea for help me?
i can use my niki for stop my door?
thanks
Works very well
This really helps me out!!!! Thanks to NetrunnerAT.
but the site is in thai language
Related
I'm new to the whole Hermes upgrading scene - but have read just about every forum thread and post on upgrading. I'm trying to follow this process:
http://forum.xda-developers.com/showthread.php?t=312943&highlight=vista
I chose to upgrade via SD card, since my windows box is a vista machine and I primarily use my mac day to day. Here's the problem I'm having - when I try to flash HardSPL V7 via the SD card (using the filename hermimg.nbh in the root of the SD card), it starts to say "loading" in bootloader mode, but then flashes up "00068002" in red at the top of the screen, and then continues into normal 3 color bootloader mode.
When I try to do the flash from vista with RUU (after following the guides showing how to downgrade to the XP drivers), I get a 262 error, and when I look in RUU.log, I see the following:
00:24:27:674 [msg] : Version : [5.10 - 20060412].
00:24:30:851 [msg] : Current Not in CE Mode or in CE Mode but ActiveSync Not Connected.
00:24:34:879 [msg] : Disconnect ActiveSync .... [0]
00:24:34:880 [msg] : Start Get Connect Port.
00:24:35:025 [msg] : Current in BL Mode. Open Port : [\\.\WCEUSBSH001] OK.
00:24:43:512 [msg] : Device BL VER : [1.04] [].
00:24:43:522 [msg] : =============================================
00:24:43:524 [msg] : START GetNBHInfo !
00:24:43:525 [msg] : END GetNBHInfo !
00:24:47:310 [msg] : Check Ac in BL mode. AC : [1]
00:24:47:314 [msg] : IsBL. BL : [1]
00:24:49:363 [msg] : =============================================
00:24:49:384 [msg] : START UpdateNBH !
00:24:50:577 [msg] : Upgrade 2 : 0 Start.
00:24:51:310 [err] : Receive Data Error : 0x713, 0x00068002.
00:24:52:040 [err] : Receive Data Error : 0x708, 0x00018002.
00:24:52:790 [err] : Receive Data Error : 0x708, 0x00018002.
00:24:52:791 [err] : Write NBH Data Error.
00:24:52:793 [err] : BL UpdateNBH Error.
00:24:52:821 [msg] : START UnInitialization !
00:24:52:843 [msg] : END UnInitialization !
Notice the line "00:24:51:310 [err] : Receive Data Error : 0x713, 0x00068002." - that 00068002 is the same number that pops up when trying to flash from the SD card.
Same exact thing happens when I try to flash anything else (like a radio rom, or an OS rom).
Any help would be greatly appreciated!
PS: my TyTN shows as a HERM200, IPL 1.00, SPL 1.04
Did you format your SD Card in Fat32?
The most common problem when flashing from card is a wrong formated card.
yes, i formatted it Fat32 and also did a chkdsk on it.
Did someone get the solution for this?
Why you people do not search before making posts?????!!!!!!
Here is what u asking for :
1. Format your SD card with FAT32.
2. Download Hermes SIM CID Unlock v3a.
3. Copy SSPL-HERM to your SD card.
4. Extract the RUU_HERM_Unlock_v3a.
5. copy HermesUnlocker_HardSPL.nbh to SD card.
6. Rename it to HERMIMG.nbh.
7. put the SD card into the device and run sspl.exe.
8. the device enters the bootloader and ...
I have problem flashing using Sandisk 1GB, formatted FAT32, .nbh in place, after tri color bootloader nothing happen, no 'Loading'. Anybody experience this problem?
When I use micro SD 256 MB (from Nokia), no problem at all, flashing process Completed.
Is SD capacity (too big) become an issue or is this bad SD card..?
some sd cards cant be used to flash roms, i dont know why, maybe someone else can explain why
argupas, did you rename the .nbh file to "hermimg.nbh? It MUST be renamed to this for sd method to work. cheers.....
ultramag69 said:
argupas, did you rename the .nbh file to "hermimg.nbh? It MUST be renamed to this for sd method to work. cheers.....
Click to expand...
Click to collapse
I already rename .nbh to HERMIMG.nbh.
I think it was SD card problem (1 GB Sandisk, I suspect a fake one), because I am now using 512 MB V-gen, no problem for flashing.
Thx.
koorosh_bsboys said:
Why you people do not search before making posts?????!!!!!!
Here is what u asking for :
1. Format your SD card with FAT32.
2. Download Hermes SIM CID Unlock v3a.
3. Copy SSPL-HERM to your SD card.
4. Extract the RUU_HERM_Unlock_v3a.
5. copy HermesUnlocker_HardSPL.nbh to SD card.
6. Rename it to HERMIMG.nbh.
7. put the SD card into the device and run sspl.exe.
8. the device enters the bootloader and ...
Click to expand...
Click to collapse
I dont understand 7th step. Now my device hang in "Windows Mobile" screen, so how can I run sspl.exe. And also if enter the bootloader, I can press Power+OK+soft reset. Is this right for enter bootloader or i must run sspl.exe?
you have to run SSPL.exe from the file explorer. It has to be run from the PHONE memory, NOT the sd card.
Try a hard reset, both soft keys and reset with stylus. Hold all buttons until it asks if you wish to reset to factory (or something like that, you get the idea). Push "r" on slideout keyboard then "space"key. you now have to go through the alignment and everything again.
Even if you use this method, make sure you install Hard SPL V7. It is safer than anything else. You should also have checked what radio rom you were using as it has now been downgraded to 1.116.x.x, this may cause you some trouble later too.
Use the sd card method to fix this as it appears safer than using the pc. Just make sure you have got Hard SPL installed and have a charged battery. DON'T just think you can put it on the charger while flashing AS IT DOESN'T CHARGE...
Cheers...
Sorry to replay this thread but i had a situation like that.
I have a Hermes, with the pin of the USB that makes connection to PC broken... So my only Shot to update the ppc is from SD. The rom i have is one of 1st realeses of hermes wm6.5, so that stucks all the time, even i hard reset it...
When i try to update something from SD i cant because gives me that error 000602... Any idea? So i have to unlock the cid, but if i cant access to the windows what i must do?
If i hard reset it, it enter in windows, but 2 ou 3 seconds that stuck :S
If you can't get into windows to run SSPL.exe to install Hard SPL & your USB is stuffed so you can't connect to PC then you have a brick... If you had Hard SPL installed 1st then you wouldn't be in this situation.
Sorry, you have a brick unless you fix the USB connector.
ultramag69 said:
If you can't get into windows to run SSPL.exe to install Hard SPL & your USB is stuffed so you can't connect to PC then you have a brick... If you had Hard SPL installed 1st then you wouldn't be in this situation.
Sorry, you have a brick unless you fix the USB connector.
Click to expand...
Click to collapse
Ok, but if i fix the usb... updating by bootloader mode and usb, i will not get the error 00068002?
Not if you install Hard SPL 1st...
I dont understand 7th step. Now my device hang in "Windows Mobile" screen, so how can I run sspl.exe
Click to expand...
Click to collapse
same me too,
My device Stuck on bootloader, Why can I run sspl.exe?
Need Help
SOLVED:::::: sorry
aladin said:
same me too,
My device Stuck on bootloader, Why can I run sspl.exe?
Need Help
SOLVED:::::: sorry
Click to expand...
Click to collapse
First off, reflash your device with your phones original carriers ROM. Your phone will accept it. It sounds like you didn't SUPERCID your phone first, and didn't HARDSPL your phone.
Make sure you HARDSPL then SUPERCID your phone FIRST!
Download your phone's original carriers ROM and flash that via SD card to your device. That should return it back to "factory" state, and get it so that you can once again try to HARDSPL and SUPERCID your phone.
Hope this helps,
Cheers
Supercid then Hard SPL... If you run the V3a unlocker it flashes your SPL to 1.40... Hard SPl V7 is the latest and greatest. Technically you shouldn't need to supercid your Hermes after Hard SPLing it.
Hi
your instruction are really complete and clear but . . .
but my TyTn to day has a problem (better I have a problem!!)
After breaking the flash of a new ROM (it was corrupted) it either stays in bootloader mode (IPL 1.01 SPL 2.03) or,after few seconds from booting and displaying all data like
M 05 R 1.56.70.11
S 04 G 32.89.7020.20H
B 06 D 3.57
turns the display full white, make a "ding" and never enter into W.M. 6.5. Hence, how can I launch HERMES-SPL.exe ???
Other attempts to flash from PC through:
- RUUWrapper provide up-date error for missed USB connection
- <ROM>. exe the flash starts but stops after few second when the status bar, on the PDA reach 1%.
So, it became a brick?? There is any chance to retrive it?
3351405372 said:
Hi
your instruction are really complete and clear but . . .
but my TyTn to day has a problem (better I have a problem!!)
After breaking the flash of a new ROM (it was corrupted) it either stays in bootloader mode (IPL 1.01 SPL 2.03) or,after few seconds from booting and displaying all data like
M 05 R 1.56.70.11
S 04 G 32.89.7020.20H
B 06 D 3.57
turns the display full white, make a "ding" and never enter into W.M. 6.5. Hence, how can I launch HERMES-SPL.exe ???
Other attempts to flash from PC through:
- RUUWrapper provide up-date error for missed USB connection
- <ROM>. exe the flash starts but stops after few second when the status bar, on the PDA reach 1%.
So, it became a brick?? There is any chance to retrive it?
Click to expand...
Click to collapse
Hey bud, if you hold the POWER BUTTON and the CAMERA button down and hit the RESET button, do you get a tricolour screen?
If so, then your phone is not bricked, just has a failed ROM on it.
You can flash via SD card onto your phone, and to do so, download the rom for your network, the one that originally came with your phone, onto your phone. when you put it on the SD card, make sure you name it HERMIMG.nbh. This'll allow you to flash via SD. put the card in, reset to the tricolour screen, and then follow the instructions for flashing.
Once this is done, you can then attempt again to SuperCID your phone.
Cheers!
hello to all
need some help in jasjam now in bootloader mood (3 cloure screen)
when flash any wam stop in (10 - 11 - 12%) and need recovery and stay in same situation
what steps can i do to repaire my phone
need help plz
thx in advance
regards melmel
Ipl 1.04
Spl-1.40.0lipro
My Device Not Start Just Boot Loader Mood Need Help Plz
Thx
You must provide more information about your device:
what is ur previous ROM?
what is the ROM that u tried to upgrade with?
did you CID Unlocked ur device before upgrading (Hardspl)?
What is your current IPL & SPL?
do u have NO GSM error?
BTW, you should read the WIKI first!!!!!!
the proplem was that phone had no gsm
i tried alot to write radio or any wam contain radio but always failed
error and not start
it make hard spl v7 and it maked succefuly in 1 second and now phone open only boot loader not done any thing more
just boot loader mood
plz any steps
thx to all
why no one posting help plz
i wanna revive my phone
DUDE!
you cannot hardspl via bootloader.
DID you read the wiki on how to unbrick ur hermes : http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
Please follow the following steps to revive your Hermes:
1- Close the USB port on the activesync.
2- open the program MTTY (you can find it within this forum) and connect your Hermes using USB.
3- inside MTTY give this command:
task 32
if the answer is FF this means your Hermes is locked and you can go on with the steps.
now give this command in MTTY
set 16 0
the answer will be (NAND WRITE SUCCESS).
4- Disconnect your Hermes from the PC.
5- Format your micro SD card with FAT16.
6- Download the official JASJAM ROM (JASJAM_WWE_1.20.305.104.zip) and extract the file hermimg_wwe_1.20.305.104.nbh and rename it to hermimg.nbh
7-Put the file hermimg.nbh on your micro SD card and inser the card into your Hermes.
8- Reboot your Hermes and it will start the command Download, in this case press the power button to continue.
The operation will take about 20 mints to finish, if it hangs do a reset and repeat step 8.
keep repeating step 8 until the operation ends with a success.
Regards.
i open active sync
from file/connection setting/(unmark) allow usb connection
and mark on allow the connection from com 1
then opem mtty.exe
but i can't write any liter
sory cause it's the firist time to use mtty.exe and can't write commands
thx to all for replies
but need to done this plz help
well...
that didnt work :|
running vista ultimate sp1, following all the guides, trying to update to RUU Nike Radio 1.58.21.23,
had the RUU Nike Radio 1.58.16.27 installed...
everything went fine untill it came to 99%... it stalled and the install program told me to follow some
recovery steps, i did, but vista cant recognize the usb device... henche, i cant connect to the phone...
is there a place for drivers or so...??
please help out a noob...
anyone...??
when i start my phone i only get the different color screen, and it says:
Niki100
SPL-1.6.0000
CPLD-4
in the top right corner it says: RUUNBH
Ah easy ... Download MTTY disable Activsync USB Connection and start MTTY -> set Connection to USB -> if you see CMD> use the commando "boot"
Have you a Windows XP PC? Vista make some troubles!
Your device boot now! if your device make troubles ... flash a full rom with SPL, Radio and OS! Have you CID Unlock your device? HardSPL, USPL or SSPL? I want know to cross check!
Your SPL is very low ... i havent this version to test it with all radio roms.
will try this asap...
i used sspl, dont know if it is CID unlocked, think so...
ok...
did what you said, but what is suposed to happen...??
i get this in the log window of mtty:
boot
Fill RSVD information for block 288 to 309
Storage start sector=0x8940, total sector=0x12980
Storage start block=570, total block=1190
Total Bad Block in CE: 0
Erase physical block from 860 to 2032
si backup: Erase physical block from 2032 to 2048
No card inserted
OEMGetUpdateMode
OEMTranslateBaseAddress 23 80000000 80000000
IPLMSG:0x8:INFO: Loading image ...
IPLMSG:0x9:INFO: Jumping to image...
OEMLaunchImage 80000000
Jump to Physical Address 10300000
you say my spl is low, any way to update this...?
uhm ... realy bad!
what nike device is yours? can you say me your country and original os your device are?
i got it working again...
tried the mtty thing again and i booted, i flash with the hardspl thingy, and updating the rom now to the: RUU_Nike_HTCASIA_AUS_1.31.710.12_Radio_Nike_1.58.21.23_signed_Ship_PA
i bought mine in norway, december 2007
its alive
thank you for your help, you serously saved my day
^_^
try to flash radio again and tell me if you get the same problem again or not! its for debuging! i think ... some flash problems come from vista.
i used a wxp laptop, and flashed with the RUU_Nike_HTCASIA_AUS_1.31.710.12_Radio_Nike_1.58.2 1.23_signed_Ship_PA rom and radio, and it all works just fine
will try again with the updated radio as soon as i get home...
Just tryed to update my Nike Rom. Now my Nike is stuck in Bootloader Mode.
It displays:
NIKI100
SPL-1.22 hard
CPLD-4
Flash stops at 73%. Please help me!!!
Need more info...
What error does it give? (If any)
Try using mtty to boot the device.
Wezternator said:
Need more info...
What error does it give? (If any)
Try using mtty to boot the device.
Click to expand...
Click to collapse
All the time error 262. tried several rom's - error 262 (stops at 89%, 98%). tired official rom - same.(stop at 73%). Tired flash with sd card-same
In bootloader it displays:
NIKI100
SPL-1.22.Hard
CPLD-4
Upgrade ROM code error. Please try again.
Please help!
Try this: Clicky!
Ignore the lower bits of that post, just grab a copy for MTTY and type 'boot' see if there is enough info on he ROM to boot he device, then try again
The problem is that I have cooked own rom, rom bad(promblem with xip), I did boot
Cmd>boot
InitDisplay: Display_Chip=1
Fill RSVD information for block 288 to 309
Storage start sector=0x8400, total sector=0x127C0
Storage start block=549, total block=1183
Total Bad Block in CE: 0
Erase physical block from 839 to 2004
si backup: Erase physical block from 2032 to 2048
No card inserted
OSSIPreLoad ++
But now stuck in first splash screen.
How to backup from hardspl to original SPL on the dead phone??
use mtty:
Fill RSVD information for block 288 to 309
Storage start sector=0x9E00, total sector=0x114C0
Storage start block=653, total block=1107
Total Bad Block in CE: 0
Erase physical block from 943 to 2032
si backup: Erase physical block from 2032 to 2048
No card inserted
OEMIPLInit clear 10MB ext RAM
OEMGetUpdateMode
IPLMSG:0x4:ERROR: Failed to retrieve stored image information.
Any idea? PLZ!
dmx_nigga said:
Any idea? PLZ!
Click to expand...
Click to collapse
Double posting puts people off wanting to help dude. Don't bump.
Tired other rom. yes!! 100%, but stuck in first bootscreen.
brothers, how to back up original spl from bootloader?
Many times I happened to cook ROM that do not work (especially with the 6.5 in Italian) but is not a problem!
probably yuor Hrdspl is not ok, try to flash it again and then flash the official rom
Link to Hard SPL 1.22
Link to Official WM 6.1 WWE with ROM 1.65.29.25
how can i flash hard spl 1.22 from bootloader?
• power off yuor niki (Remove for a couple of seconds the battery)
• press and hold power and camera buttons,you must have (tree color) bootloader
• connect usb cable
• run ROMUpdateUtility.exe (or Nike CustomRUU.exe) in a folther with hardspl-1.22-nike.nbh
salvy.c.83,I can't flash hardspl, it's stop at 0%..help please..
salvy.c.83 said:
• power off yuor niki (Remove for a couple of seconds the battery)
• press and hold power and camera buttons,you must have (tree color) bootloader
• connect usb cable
• run ROMUpdateUtility.exe (or Nike CustomRUU.exe) in a folther with hardspl-1.22-nike.nbh
Click to expand...
Click to collapse
Don't you need an SPL Jump running to upgrade the SPL? But, if you can't get into an OS you can't run the jump exe.
You need to find a really old ROM hat only requires the HardSPL you have then flash that. Or try an official one? Or have you already tried that
after unlock my athena is dead, go only in bootloader mode with this write:
ATHE100
IPL-1.00
ATHE100
SPL-v1.10.RP00
ALL ROM NOT RUN, CAN NOT CHANGE SPL,
I HAVE TRIED AND ORIGINAL ROM version hangs 1% WITH THE WRITTEN "INVALID ID .."
PLEASE HELP ME
GORGOMED
Don't worry, it happens all the time. Just follow the procedure of "How to fix the invalid model ID after bad flashing" step by step as described in the following page:
http://forum.xda-developers.com/showthread.php?t=405814
Good luck!
hi,i make this procedure ,but replay of the athena is this:
Cmd>task 32
Wait interpreter timeout
Level = FF
have read in some post ,when reply is FF is because SPL is original ,in fact my SPL is 1.10.RP00 not 1.12 olinex or olipro ,i needed how do I change only SPL and make open to Athena for upgrade rom.
tnx
RE HELP
I'm trying to put the original ROM, 1% BUT STOPS AND WRITE ERROR VENDOR ID "mtty DO THE PROCEDURE, BUT I DO NOT TO" LEVEL 0 "MA" LEVEL FF "AND I CAN NOT PUT THE MAC LIKE GOING FORWARD?
TNX
please help me
who is help me!!
tnx
nessuno parla italiano e mi fa capire che devo fare
giusto ,chi sa che devo fare?
Maybe this?
gorgomed said:
after unlock my athena is dead, go only in bootloader mode with this write:
ATHE100
IPL-1.00
ATHE100
SPL-v1.10.RP00
ALL ROM NOT RUN, CAN NOT CHANGE SPL,
I HAVE TRIED AND ORIGINAL ROM version hangs 1% WITH THE WRITTEN "INVALID ID .."
PLEASE HELP ME
GORGOMED
Click to expand...
Click to collapse
Try this...I do not know if you need to reset your MAC address...
http://forum.xda-developers.com/showthread.php?t=387454&highlight=mtty&page=4
I had this once and I needed a new MAC address....you can get it from any unused wireless device.
i make this procedure 100 times,but also write up :
STEP BY STEP:
1. download attachment at the end of the post for mac1.exe (requires .net 2.0 installed on the PC)
2. you will also need to download the other attachment in this post for the mtty program.
3. enter bootloader (tricolour screen) manually by pressing and holding camera button all the way in (yes I mean that, press it in as hard as you can!!), while doing a reset, then keep the camera button held until you see the tricolour screen.
4. disable USB in activesync (wmdc if you have vista - in this case, do not kill wmdc, just disable usb in it!!!)
5. run mtty and select USB option from the dropdown box!
6. then press enter in main window that comes up, see if that gives you Cmd>
7. now you should have Cmd>, if not, re-check if you did the above steps right until you get Cmd>
8. now run the mac1.exe, type in your MAC address you want to use for the Athena, if you have SPL 3.xx reported on the tricolour screen, then use the button for SPL 3.xx, otherwise if you have SPL 1.xx reported, use button for 1.xx.
9. this should have generated a .bin file for you, copy that bin file in the folder of mtty.
10. now, in mtty, type (do not copypaste!) this command: task 32
11. this should return Level = 0 - MY RETURN NOT LEVEL 00 BUT LEVEL FF
BECAUSE I DO NOT SPL 1.20 OR 3.XX NOT PACHED,THIS MY PROBLEM
I DO NOT CHANGE SPL ,SAY YOU MAKE A SOLUTION?
12. now, you must only do one of the two following commands:
- if you have SPL 3.xx, then type (do not copypaste!!) this command: lnb filename.bin 76508000
(there filename is the name of the .bin file you generated - don't forget to put .bin after filename, as the full name is needed).
- OR, if you have SPL 1.xx, then the command is different (do not copypaste!!): lnbs filename.bin 75108000
(there filename is the name of the .bin file you generated - don't forget to put .bin after filename, as the full name is needed).
When you try to unlock did you use HARDSPL from cmonex? Is the SPL SPL-v1.10.RP00 the ORIGINAL spl of the phone?
** If you DID NOT use HARDSPL YOU WILL GET Level=FF.
** HARDSPL is available here: http://forum.xda-developers.com/showthread.php?t=316846
Just retry HARDSPL. When you gst to boot loader you should see olipro SPL.
If I understand correctly, you made a mistake by not changing SPL in first case. It is not clear what you did to 'unlock" the phone...like you said in the first post what did you do for unlocking? How did you unlock?
The best unlock is HARDSPL>>>
yes,i make procedure but in the end athena is blocked,with up writing,now not run ,only reset and bootloader,do not have SPL 1.20 olipro ,not have MAC ,if i writing new ROM also original ,reply "invalid vendor".
Now i make AthenaWrapper but end write this"
ERROR 300 INVALID UPDATE TOOL.
tnx
What ROM are you trying to flash? I think since it still has the ORIGINAL SPL it will take only the original HTC ROM? Did you try that?
Try this other unlocker also ....it is here: http://forum.xda-developers.com/showthread.php?t=315831
Also, I need some way to text you better than this .....otherwise I can only give one suggestion per day !!!!
x7500
please i have the same problem.
but when a type this Inbs filename.bin 75108000 what must i do after that?
my athena caracteristic are:
ATHE100
IPL-v2.02
ATHE100
SPL-v1.20.Olipro
thank you
try flashing an spl 1.2 rom
readthe guide
http://forum.xda-developers.com/showthread.php?t=429013