hello to all
need some help in jasjam now in bootloader mood (3 cloure screen)
when flash any wam stop in (10 - 11 - 12%) and need recovery and stay in same situation
what steps can i do to repaire my phone
need help plz
thx in advance
regards melmel
Ipl 1.04
Spl-1.40.0lipro
My Device Not Start Just Boot Loader Mood Need Help Plz
Thx
You must provide more information about your device:
what is ur previous ROM?
what is the ROM that u tried to upgrade with?
did you CID Unlocked ur device before upgrading (Hardspl)?
What is your current IPL & SPL?
do u have NO GSM error?
BTW, you should read the WIKI first!!!!!!
the proplem was that phone had no gsm
i tried alot to write radio or any wam contain radio but always failed
error and not start
it make hard spl v7 and it maked succefuly in 1 second and now phone open only boot loader not done any thing more
just boot loader mood
plz any steps
thx to all
why no one posting help plz
i wanna revive my phone
DUDE!
you cannot hardspl via bootloader.
DID you read the wiki on how to unbrick ur hermes : http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
Please follow the following steps to revive your Hermes:
1- Close the USB port on the activesync.
2- open the program MTTY (you can find it within this forum) and connect your Hermes using USB.
3- inside MTTY give this command:
task 32
if the answer is FF this means your Hermes is locked and you can go on with the steps.
now give this command in MTTY
set 16 0
the answer will be (NAND WRITE SUCCESS).
4- Disconnect your Hermes from the PC.
5- Format your micro SD card with FAT16.
6- Download the official JASJAM ROM (JASJAM_WWE_1.20.305.104.zip) and extract the file hermimg_wwe_1.20.305.104.nbh and rename it to hermimg.nbh
7-Put the file hermimg.nbh on your micro SD card and inser the card into your Hermes.
8- Reboot your Hermes and it will start the command Download, in this case press the power button to continue.
The operation will take about 20 mints to finish, if it hangs do a reset and repeat step 8.
keep repeating step 8 until the operation ends with a success.
Regards.
i open active sync
from file/connection setting/(unmark) allow usb connection
and mark on allow the connection from com 1
then opem mtty.exe
but i can't write any liter
sory cause it's the firist time to use mtty.exe and can't write commands
thx to all for replies
but need to done this plz help
Related
I'm new to the whole Hermes upgrading scene - but have read just about every forum thread and post on upgrading. I'm trying to follow this process:
http://forum.xda-developers.com/showthread.php?t=312943&highlight=vista
I chose to upgrade via SD card, since my windows box is a vista machine and I primarily use my mac day to day. Here's the problem I'm having - when I try to flash HardSPL V7 via the SD card (using the filename hermimg.nbh in the root of the SD card), it starts to say "loading" in bootloader mode, but then flashes up "00068002" in red at the top of the screen, and then continues into normal 3 color bootloader mode.
When I try to do the flash from vista with RUU (after following the guides showing how to downgrade to the XP drivers), I get a 262 error, and when I look in RUU.log, I see the following:
00:24:27:674 [msg] : Version : [5.10 - 20060412].
00:24:30:851 [msg] : Current Not in CE Mode or in CE Mode but ActiveSync Not Connected.
00:24:34:879 [msg] : Disconnect ActiveSync .... [0]
00:24:34:880 [msg] : Start Get Connect Port.
00:24:35:025 [msg] : Current in BL Mode. Open Port : [\\.\WCEUSBSH001] OK.
00:24:43:512 [msg] : Device BL VER : [1.04] [].
00:24:43:522 [msg] : =============================================
00:24:43:524 [msg] : START GetNBHInfo !
00:24:43:525 [msg] : END GetNBHInfo !
00:24:47:310 [msg] : Check Ac in BL mode. AC : [1]
00:24:47:314 [msg] : IsBL. BL : [1]
00:24:49:363 [msg] : =============================================
00:24:49:384 [msg] : START UpdateNBH !
00:24:50:577 [msg] : Upgrade 2 : 0 Start.
00:24:51:310 [err] : Receive Data Error : 0x713, 0x00068002.
00:24:52:040 [err] : Receive Data Error : 0x708, 0x00018002.
00:24:52:790 [err] : Receive Data Error : 0x708, 0x00018002.
00:24:52:791 [err] : Write NBH Data Error.
00:24:52:793 [err] : BL UpdateNBH Error.
00:24:52:821 [msg] : START UnInitialization !
00:24:52:843 [msg] : END UnInitialization !
Notice the line "00:24:51:310 [err] : Receive Data Error : 0x713, 0x00068002." - that 00068002 is the same number that pops up when trying to flash from the SD card.
Same exact thing happens when I try to flash anything else (like a radio rom, or an OS rom).
Any help would be greatly appreciated!
PS: my TyTN shows as a HERM200, IPL 1.00, SPL 1.04
Did you format your SD Card in Fat32?
The most common problem when flashing from card is a wrong formated card.
yes, i formatted it Fat32 and also did a chkdsk on it.
Did someone get the solution for this?
Why you people do not search before making posts?????!!!!!!
Here is what u asking for :
1. Format your SD card with FAT32.
2. Download Hermes SIM CID Unlock v3a.
3. Copy SSPL-HERM to your SD card.
4. Extract the RUU_HERM_Unlock_v3a.
5. copy HermesUnlocker_HardSPL.nbh to SD card.
6. Rename it to HERMIMG.nbh.
7. put the SD card into the device and run sspl.exe.
8. the device enters the bootloader and ...
I have problem flashing using Sandisk 1GB, formatted FAT32, .nbh in place, after tri color bootloader nothing happen, no 'Loading'. Anybody experience this problem?
When I use micro SD 256 MB (from Nokia), no problem at all, flashing process Completed.
Is SD capacity (too big) become an issue or is this bad SD card..?
some sd cards cant be used to flash roms, i dont know why, maybe someone else can explain why
argupas, did you rename the .nbh file to "hermimg.nbh? It MUST be renamed to this for sd method to work. cheers.....
ultramag69 said:
argupas, did you rename the .nbh file to "hermimg.nbh? It MUST be renamed to this for sd method to work. cheers.....
Click to expand...
Click to collapse
I already rename .nbh to HERMIMG.nbh.
I think it was SD card problem (1 GB Sandisk, I suspect a fake one), because I am now using 512 MB V-gen, no problem for flashing.
Thx.
koorosh_bsboys said:
Why you people do not search before making posts?????!!!!!!
Here is what u asking for :
1. Format your SD card with FAT32.
2. Download Hermes SIM CID Unlock v3a.
3. Copy SSPL-HERM to your SD card.
4. Extract the RUU_HERM_Unlock_v3a.
5. copy HermesUnlocker_HardSPL.nbh to SD card.
6. Rename it to HERMIMG.nbh.
7. put the SD card into the device and run sspl.exe.
8. the device enters the bootloader and ...
Click to expand...
Click to collapse
I dont understand 7th step. Now my device hang in "Windows Mobile" screen, so how can I run sspl.exe. And also if enter the bootloader, I can press Power+OK+soft reset. Is this right for enter bootloader or i must run sspl.exe?
you have to run SSPL.exe from the file explorer. It has to be run from the PHONE memory, NOT the sd card.
Try a hard reset, both soft keys and reset with stylus. Hold all buttons until it asks if you wish to reset to factory (or something like that, you get the idea). Push "r" on slideout keyboard then "space"key. you now have to go through the alignment and everything again.
Even if you use this method, make sure you install Hard SPL V7. It is safer than anything else. You should also have checked what radio rom you were using as it has now been downgraded to 1.116.x.x, this may cause you some trouble later too.
Use the sd card method to fix this as it appears safer than using the pc. Just make sure you have got Hard SPL installed and have a charged battery. DON'T just think you can put it on the charger while flashing AS IT DOESN'T CHARGE...
Cheers...
Sorry to replay this thread but i had a situation like that.
I have a Hermes, with the pin of the USB that makes connection to PC broken... So my only Shot to update the ppc is from SD. The rom i have is one of 1st realeses of hermes wm6.5, so that stucks all the time, even i hard reset it...
When i try to update something from SD i cant because gives me that error 000602... Any idea? So i have to unlock the cid, but if i cant access to the windows what i must do?
If i hard reset it, it enter in windows, but 2 ou 3 seconds that stuck :S
If you can't get into windows to run SSPL.exe to install Hard SPL & your USB is stuffed so you can't connect to PC then you have a brick... If you had Hard SPL installed 1st then you wouldn't be in this situation.
Sorry, you have a brick unless you fix the USB connector.
ultramag69 said:
If you can't get into windows to run SSPL.exe to install Hard SPL & your USB is stuffed so you can't connect to PC then you have a brick... If you had Hard SPL installed 1st then you wouldn't be in this situation.
Sorry, you have a brick unless you fix the USB connector.
Click to expand...
Click to collapse
Ok, but if i fix the usb... updating by bootloader mode and usb, i will not get the error 00068002?
Not if you install Hard SPL 1st...
I dont understand 7th step. Now my device hang in "Windows Mobile" screen, so how can I run sspl.exe
Click to expand...
Click to collapse
same me too,
My device Stuck on bootloader, Why can I run sspl.exe?
Need Help
SOLVED:::::: sorry
aladin said:
same me too,
My device Stuck on bootloader, Why can I run sspl.exe?
Need Help
SOLVED:::::: sorry
Click to expand...
Click to collapse
First off, reflash your device with your phones original carriers ROM. Your phone will accept it. It sounds like you didn't SUPERCID your phone first, and didn't HARDSPL your phone.
Make sure you HARDSPL then SUPERCID your phone FIRST!
Download your phone's original carriers ROM and flash that via SD card to your device. That should return it back to "factory" state, and get it so that you can once again try to HARDSPL and SUPERCID your phone.
Hope this helps,
Cheers
Supercid then Hard SPL... If you run the V3a unlocker it flashes your SPL to 1.40... Hard SPl V7 is the latest and greatest. Technically you shouldn't need to supercid your Hermes after Hard SPLing it.
Hi
your instruction are really complete and clear but . . .
but my TyTn to day has a problem (better I have a problem!!)
After breaking the flash of a new ROM (it was corrupted) it either stays in bootloader mode (IPL 1.01 SPL 2.03) or,after few seconds from booting and displaying all data like
M 05 R 1.56.70.11
S 04 G 32.89.7020.20H
B 06 D 3.57
turns the display full white, make a "ding" and never enter into W.M. 6.5. Hence, how can I launch HERMES-SPL.exe ???
Other attempts to flash from PC through:
- RUUWrapper provide up-date error for missed USB connection
- <ROM>. exe the flash starts but stops after few second when the status bar, on the PDA reach 1%.
So, it became a brick?? There is any chance to retrive it?
3351405372 said:
Hi
your instruction are really complete and clear but . . .
but my TyTn to day has a problem (better I have a problem!!)
After breaking the flash of a new ROM (it was corrupted) it either stays in bootloader mode (IPL 1.01 SPL 2.03) or,after few seconds from booting and displaying all data like
M 05 R 1.56.70.11
S 04 G 32.89.7020.20H
B 06 D 3.57
turns the display full white, make a "ding" and never enter into W.M. 6.5. Hence, how can I launch HERMES-SPL.exe ???
Other attempts to flash from PC through:
- RUUWrapper provide up-date error for missed USB connection
- <ROM>. exe the flash starts but stops after few second when the status bar, on the PDA reach 1%.
So, it became a brick?? There is any chance to retrive it?
Click to expand...
Click to collapse
Hey bud, if you hold the POWER BUTTON and the CAMERA button down and hit the RESET button, do you get a tricolour screen?
If so, then your phone is not bricked, just has a failed ROM on it.
You can flash via SD card onto your phone, and to do so, download the rom for your network, the one that originally came with your phone, onto your phone. when you put it on the SD card, make sure you name it HERMIMG.nbh. This'll allow you to flash via SD. put the card in, reset to the tricolour screen, and then follow the instructions for flashing.
Once this is done, you can then attempt again to SuperCID your phone.
Cheers!
hi
I need your help to fix my O2 Atom Exec.
i wanted to upgrade my ROM in to the WM6, at the bigining i copied the "diskimage_Ver.nb0" & "EBOOT.nb0" on my memory card. and got my Atom Exec into the bootloader , after download complited the LCD got dark, i got it on bootloader and start the "Device Software Update Utility" and clicked on "Next" until "Upgrad" was shown.When I clicked on "upgrade" this error was shown:"CONNECTION ERROR" . What should i do to fix it?
Thanks.
I'm looking for your answer.
donot ever try thru SD card.. there is a chance that you may brick your device.
Goto bootloader mode first then u run DSUU.
Now after i did that, it dosent work with DSUU .it show "error connection".and my divice shows the upgrade fail
How many files you have in the upgrade directory? Normally it should contain 6 files:
- Device Software Update Utility.exe
- diskimage_Ver.nb0
- EBOOT.nb0
- ExtendedRom.img
- nova_pda_033105.mot
- vl1d_pda_Ver.mot
It will always shown connection error if one of these files is missing
I have all of them,
It seems feasiable to full downloadig the Rom from SD(memory card), but i need mor files:
"diskimg.nb0 , eboot.nb0 , dm.nbo , flash.img , agent.mot , mot.mot , CPLD.img , assetInf.img , extended.img , Mdoc.img"
If it's possible to upgrading with them how can i rech them ?
hello...!!!?
can enybody help me with this case? I need Your Help. Please. . . .
shaemna said:
hi
I need your help to fix my O2 Atom Exec.
i wanted to upgrade my ROM in to the WM6, at the bigining i copied the "diskimage_Ver.nb0" & "EBOOT.nb0" on my memory card. and got my Atom Exec into the bootloader , after download complited the LCD got dark, i got it on bootloader and start the "Device Software Update Utility" and clicked on "Next" until "Upgrad" was shown.When I clicked on "upgrade" this error was shown:"CONNECTION ERROR" . What should i do to fix it?
Thanks.
I'm looking for your answer.
Click to expand...
Click to collapse
Why did you do this?! No one gave out instructions to flash anything using SD CARD in the first place! Of course you will get connection error because bootloader is not functioning. Remove your SDCard, start bootloader mode, and flash the normal way.
I did that but it's not worked. and got me "error connection", i saw some where that if i do it in the that way (with sd) it's worke and beacuse of that i did it in that wey, now what should i do? how can upgrad my ROM or downgrad it, my divice is alredy ded, how can i get it alive? help me
shaemna said:
I did that but it's not worked. and got me "error connection", i saw some where that if i do it in the that way (with sd) it's worke and beacuse of that i did it in that wey, now what should i do? how can upgrad my ROM or downgrad it, my divice is alredy ded, how can i get it alive? help me
Click to expand...
Click to collapse
can you go into bootloader mode?
yes it's go to the bootloader but when run DSUU plase of the last version of the rom and radio is empty, when i click on UPGRAD it get me ERROR CONNECTION
shaemna said:
yes it's go to the bootloader but when run DSUU plase of the last version of the rom and radio is empty, when i click on UPGRAD it get me ERROR CONNECTION
Click to expand...
Click to collapse
I'm sorry. I don't get you. You can go to bootloader, but you get an error. Can you post a screen shot of the error? so, I will know what to do.
How can I uplod picturs?
server is busy it get me Network Error (tcp_error) and cant upload it
the doucument of it is:
(the upgrade page)
Your Divice software is about to be update from:
divice CE image version:0
divice Radio image version:
to:
CE image version: 7210621
Radio image version: R060711N-MN2ARC-RS00011
.......
PLEAS CLICK update to continue
when i click upgrade it show me the fowloeeng error
ERROR:CONNECTION ERROR
THE DIVICE SOFTWAR UPDATE IS HAVING TROUBLE CONECTING TO YOUR DIVICE
PLEAS CHEKE
1)YUOR DIVICE IS PROPLY CONNECTED TO THE USB CABLE OR ...
.
.
.
now what should i do?
do you have any other USB to mini-USB cable? try changing it... The ones used for SD Card readers or Digital Cameras are the same, and do it again.
i do that in all of my USB ports and they are same and get me error conection again
Is there any wey else to inistall a ROM on my divice?
1) Is windows recognizing your device?.. (Do you have activesync installed?)
2) Did u try using different USB cable ?
3) Are you logged on as administrator?
4) Did you remove SD card before going to bootloader mode
5) What is the screen content when you go to boot loader mode
6) Before connecting the device go to bootloader first, then connect the device and then run DSUU
7) Activesync may install device drivers for your device so try installing activesync?
Thanks
when i get my divice in to the bootloader it's display:
===========MN2 Bootloader=
Jun 13 2006 20:41:44
copyright (c) 2006 Quanta cor
poration
CPLD Ver: A0060109
***********************
*Using '<-','->', 'Enter' *
*to choose what you want *
***********************
(1)debug module through UART
(2)jump to DM
enter your selection:
when i conect it to pc( as administrator user) the fallowing line was shown:
USB connected , waiting for download command...
and my computer beeping and found new hardware but not connected to activesync(4.5) , then i start DSUU and when start to upgrade computer show me "ERROR CONECTION" and my divice show me this note:
! ! ! Please use DSUU in OS mode and sync with pc first ! ! !
Usb transfer Fail
please help me
1. We get the most first sewing of Xda-atomexec-eng-20060614_r060428n_ex0028.exe (only by this sewing restore was able)
2. We drag out the files of eboot.nb0
3. We copy on miniSD in a root directory.
4. We insert miniSD in Pocket, enter in bootloader (Camera+SR)
5. We wait inundated while.
6. We take out a miniSD, enter in bootloader, start sewing on PC, connect to USB (it is needed to put to death in the processes of AS)
We are sewn!!!
Is Any Solution That Sspl-herm.EXE Can Start With Windows Command?? I MEAN I CAN ONLY PUT PUT MY BRICKED TYTN IN BOOTLOADER BAT CAN NOT START SSPL-HERM.EXE BECAUSE NOT WANT TO LOAD ....IS ANY CHANCE TU START Sspl-herm.EXE WITH WINDOWS COMMAND TO CHANGE BOOTLOADER TYTN IN SSPL HERM THEN WE CAN FLASH BRICKED DEVICE!!!??
SO I HOPE THAT SOMEBODY CAN CREATE PATCH FOR THIS THAT SSPL-HERM.EXE CAN START IN WINDOWS THEN CHENGE BOOTLOADER IN HERMES WHEN HERMES CONNECTED WITH USB AND ONLY CAN LOAD BOOTLOADER.....
I MEAN
THAT Sspl-herm.EXE CAN RUN IN WINDOWS AND CHENGE AUTOMATICALY BOOTLOADER IN PHONE WHEN PHONE ONLY CAN RUN BOOTLOADER AND CAN NOT RUN OS...I HOPE THAT YOU UNDERSTAND WHAT I MEAN SORY FOR MY BAD ENGLISH.
When you put your hermes to bootloader, and you plug in usb cable, if the text changes to usb then you should be able to be able to flash any ROM. If you try flashing with SD card, it will work if you can get it to boot loader.
you not read all my post why i ask this because:
I WANT TO UnBrick the Bricked Hermes with "SPL 2.03 - IPL 1.04 - NO GSM - KITL Disabled"
There are many people have this kind of brick but still no solution for it.
I want to ask the mods to make this thread sticky so if anyone find a sulotion for this type of brick would post it Here.
Summary :
IPL: 1.04
SPL: 2.03
CID: NO SUPER CID LEVEL=FFF
NO GSM
KITL Disabled
I have tested all the possible sulotions available in the wiki but none of the could help me unbrick my hermes.
P.S. : Please just post your sulotions here NOT your comments like "you CAN TRY THIS I TRY ALL IN XDA DEVELOPERS", "It's your fault to use telstra wm6"
mbsshop1302gsm said:
Is Any Solution That Sspl-herm.EXE Can Start With Windows Command?? I MEAN I CAN ONLY PUT PUT MY BRICKED TYTN IN BOOTLOADER BAT CAN NOT START SSPL-HERM.EXE BECAUSE NOT WANT TO LOAD ....IS ANY CHANCE TU START Sspl-herm.EXE WITH WINDOWS COMMAND TO CHANGE BOOTLOADER TYTN IN SSPL HERM THEN WE CAN FLASH BRICKED DEVICE!!!??
SO I HOPE THAT SOMEBODY CAN CREATE PATCH FOR THIS THAT SSPL-HERM.EXE CAN START IN WINDOWS THEN CHENGE BOOTLOADER IN HERMES WHEN HERMES CONNECTED WITH USB AND ONLY CAN LOAD BOOTLOADER.....
I MEAN
THAT Sspl-herm.EXE CAN RUN IN WINDOWS AND CHENGE AUTOMATICALY BOOTLOADER IN PHONE WHEN PHONE ONLY CAN RUN BOOTLOADER AND CAN NOT RUN OS...I HOPE THAT YOU UNDERSTAND WHAT I MEAN SORY FOR MY BAD ENGLISH.
Click to expand...
Click to collapse
...you might get more help if you don't use caps lock... as it is, I have no interest past reading the first 3 words.
Hi all,
i've found an alternative approach to flash any firmware on HERMES 200.
I had a problem while i was trying to upgrade my WM5 Vodafone 1605 to WM6.
My bootloader is SPL-1.09, and i've tried in many ways to install Hard-spl v7 but here is what was keeping happening:
- I try to flash my Hermes with hardSPL v7 and each time:
- Hermes switch to bootloader mode and display
HERM200
IPL-SSPL by Des
HERM200
SPL-1.09.ds
- Activesync lose the connection
- Windows XP send popup with new USB device and ask me to install the new device (no idea of driver not found by default)
- RUUWrapper display error 260
Click to expand...
Click to collapse
Here is the solution:
- Download the firmware u wish to install on your device
- Unpack the firmware (right-click and Extract)
- copy the .nbh file into you microSD card and rename it as: HERMIMG.nbh
- put SSPL-HERM.exe into you device (you can get this app in this site too)
- now put you microSD card into you device and run SSPL-HERM.exe
- enjoy
I'm just an unexpert user that has tried many times to upgrade his device reading other posts on this forum. So pls correct me if i've said something wrong!
I wrote this post just cause i was going crazy and i wasn't able to find a solution like this around the sites
Hope this help somebody!
PS: I'm sorry for my bad english!
RUUWrapper display error 260? try to disable your firewall, flash again, and you will see it works.
regards chief
i've got the same problem with my hermes...
i don't know how to fix...when i start the flashing process the device switches in the bootloader mode and then nothing else is happening, there is no connection to the pc. i tried to switch off the firewall, i changed the cable, i changed usb port but nothing happens...
does anybody know what i shall do?
its the same fault as anvillani describes, the only thing different is that i dont get herm200 but herm300
Do you guys do ANY research before trying this???
Go to this thread - http://forum.xda-developers.com/showthread.php?t=296722
Go to page 116, post 1160 and READ it step by step, juymp ahead and this WON'T work. Just make sure you use a 2Gb or less sd card. INSTALL HARD SPL 1st.... Then you can use the sd card method (just skip the steps using sspl.exe as you should now have Hard SPL) to update your roms....
Cheers...
i really dont know what you want to say with this...
i tried the normal procedure to flash hard spl to my device and i tried the method anvillani suggested and both didn't funtion.
so my question is what i should do...
Follow the link and instructions in my previous post. It will allow you to install Hard SPL using the sd card method. You do need to be able to get to the today screen though.
After reading anvillani's post I'll add that the sd card MUST be 2Gb or less and has to be formatted FAT32. You have to name the .nbh file hermimg.nbh with NO speeling (sorry, spelling :b) errors or it won't work.
Cheers...
I try to flash rom ENG to my NIKi
my version is 1.31.406
I read post "Nike SSPL, USPL and HardSPL" by jockyw2001
1. download the attached files
2. REMOVE SIM and SD CARDS !!
3. connect usb cable
4. copy sspl-1.16-nike.exe to your device and run it (usb cable must be connected!)
5. after a few seconds "USB" appears on the display
6. unplug and replug the usb cable
8. you can now flash the hardspl-1.15mfg-nike.nbh by running ROMUpdateUtility.exe from flash-uspl-niki
******* but it's still 0% and still boot loader screen*****
I Hard reset my NIKI but still bootloader and show
NIKI100
SPL-1.16.0000
CPLD-4
I try to flash this rom "RUU_Nike_HTC_WWE_1[1].13.405.01_Radio_Nike_1.58.11.07_signed_Test.exe"
It's 1% only and report error 262
"ERROR [262, 276, 284, 302] : UPDATE ERROR
This error occurs during the CE ROM code upgrade process.
Solution: If this happens, you can just soft-reset the device and run RUU again. The update process will then continue."
How to repair this
in post "http://forum.xda-developers.com/showthread.php?t=387217" by NetrunnerAT
"1. Download MTTY and connect via USB (dont forget do disable Activ Sync!!) us command Boot, to force a OS Boot!
2. After OS is Started ... Download SSPL and Copy it to your Phone ... please remove SD Card and SIM ... Start this Program!
3. Now you are in the Bootloader but it tells something about SPL 1.16Jump ... now you can Flash Hard SPL!!! If you doesnt see 1.16Jump you CAN'T Flash HardSPL!!
4. Now you can Flash my Dumped TIM Rom!!! "
I try this It show log
"boot
Fill RSVD information for block 288 to 309
Storage start sector=0xAF00, total sector=0x103C0
Storage start block=721, total block=1039
Total Bad Block in CE: 0
Erase physical block from 1011 to 2032
si backup: Erase physical block from 2032 to 2048
Card inserted
SDHW_EnablePowerOn
SDHW_ConfigGPIO
Cmd5 CMD_TIMEOUT
Cmd8 CMD_TIMEOUT
SD Init OK
SDFATChkConf: RhOpenFile() failed NIKECONF.txt
OEMGetUpdateMode
OEMTranslateBaseAddress 23 80000000 80000000
IPLMSG:0x8:INFO: Loading image ...
IPLMSG:0x9:INFO: Jumping to image...
OEMLaunchImage 80000000
Jump to Physical Address 10300000"
and still boot loader
how to fix it's
Thank' for reply
Please tell us ... what you have done before ... step by step!!!!
If you stay in the Bootloader and MTTY "boot" doesnt work, try the oemsbl with the command "cego"
NEXT ... what NIKI you have? German? UK? TIM? Vodovone branded?
You tell us not enough, too help you!
NetrunnerAT said:
Please tell us ... what you have done before ... step by step!!!!
If you stay in the Bootloader and MTTY "boot" doesnt work, try the oemsbl with the command "cego"
NEXT ... what NIKI you have? German? UK? TIM? Vodovone branded?
You tell us not enough, too help you!
Click to expand...
Click to collapse
Sorry For My Eng = =' I'm Thai girl.
I can't Remember lang before flash becouse I don't Know ^ ^ GER or Italy or Rus Lang
It's Not Eng Lang not Vodafone Brand
I'm new bie for this model . I have Dopod 818 pro It's Easy to flash I think Niki Is same
command "cego" notwork
Can I reflash any Office Rom?
What is SPL-1.16.0000 mean It's Hard SPL,SSPL or USPL
I Try to Put camera button and power button
and Use Mtty
boot
InitDisplay: Display_Chip=1
Card inserted
SDHW_EnablePowerOn
SDHW_ConfigGPIO
Cmd5 CMD_TIMEOUT
Cmd8 CMD_TIMEOUT
SD Init OK
SDFATChkConf: RhOpenFile() failed NIKECONF.txt
OSSIReadBack ++
Read SI data from flash success
tail signature match
Checksum match
UserStorageSIPreload ++
My NIKI Can boot and Use Now
I don't Know what Lang
" A Propos de
Windows Mobile 6 Profesional
Processeur : MSM7200-400Mhz
Memorie :101.67 Mo
Conecteur d'ext. :En cours d'utilisation
Informations de L'appareil
Version de Rom :1.31.406.09
Date de Rom :10/30/07
Version de Radio 1.58.16.27
Version de prot.. 25.61.30.03w
Is lang France?
@^ ^@
Hoorayyyyyyy
My phone is back
many thank's for NetrunnerAT
1. Download MTTY and connect via USB (dont forget do disable Activ Sync!!) us command Boot, to force a OS Boot!
2. After OS is Started ... Download SSPL and Copy it to your Phone ... please remove SD Card and SIM ... Start this Program!
3. Now you are in the Bootloader but it tells something about SPL 1.16Jump ... now you can Flash Hard SPL!!! If you doesnt see 1.16Jump you CAN'T Flash HardSPL!!
4. Now you can Flash my Dumped TIM Rom!!! "
and Now I Use rom TOM_Niki-Project_WM6[1].1_WWE_16keys_signed_Ship.exe
Many many Thank For XDA - Developers
http://www.pdamobiz.com/ <- its a Thai PDA Board!
The most errors on HTC Niki are simulare with HTC Polaris and HTC Kaiser!!!
I hope this helps!
my touch dual is lock at 3 color mode
Sorry for my english....
My niki is locked afther flash for unlock it (supercid)
I've tried to install a sspl and hardspl, but all have crashed at 95%
I've tried to install hardspl renaming the file nbh in NIKEIMG.nbh from sd, but this procedure have only send me message: loading......... and nothing all.....
At this moment my niki is stopped at 3 colors mode
Have you any idea for help me?
Many thanks to all
don't have any idea for help me?
i can use my niki for stop my door?
thanks
Works very well
This really helps me out!!!! Thanks to NetrunnerAT.
but the site is in thai language