Just tryed to update my Nike Rom. Now my Nike is stuck in Bootloader Mode.
It displays:
NIKI100
SPL-1.22 hard
CPLD-4
Flash stops at 73%. Please help me!!!
Need more info...
What error does it give? (If any)
Try using mtty to boot the device.
Wezternator said:
Need more info...
What error does it give? (If any)
Try using mtty to boot the device.
Click to expand...
Click to collapse
All the time error 262. tried several rom's - error 262 (stops at 89%, 98%). tired official rom - same.(stop at 73%). Tired flash with sd card-same
In bootloader it displays:
NIKI100
SPL-1.22.Hard
CPLD-4
Upgrade ROM code error. Please try again.
Please help!
Try this: Clicky!
Ignore the lower bits of that post, just grab a copy for MTTY and type 'boot' see if there is enough info on he ROM to boot he device, then try again
The problem is that I have cooked own rom, rom bad(promblem with xip), I did boot
Cmd>boot
InitDisplay: Display_Chip=1
Fill RSVD information for block 288 to 309
Storage start sector=0x8400, total sector=0x127C0
Storage start block=549, total block=1183
Total Bad Block in CE: 0
Erase physical block from 839 to 2004
si backup: Erase physical block from 2032 to 2048
No card inserted
OSSIPreLoad ++
But now stuck in first splash screen.
How to backup from hardspl to original SPL on the dead phone??
use mtty:
Fill RSVD information for block 288 to 309
Storage start sector=0x9E00, total sector=0x114C0
Storage start block=653, total block=1107
Total Bad Block in CE: 0
Erase physical block from 943 to 2032
si backup: Erase physical block from 2032 to 2048
No card inserted
OEMIPLInit clear 10MB ext RAM
OEMGetUpdateMode
IPLMSG:0x4:ERROR: Failed to retrieve stored image information.
Any idea? PLZ!
dmx_nigga said:
Any idea? PLZ!
Click to expand...
Click to collapse
Double posting puts people off wanting to help dude. Don't bump.
Tired other rom. yes!! 100%, but stuck in first bootscreen.
brothers, how to back up original spl from bootloader?
Many times I happened to cook ROM that do not work (especially with the 6.5 in Italian) but is not a problem!
probably yuor Hrdspl is not ok, try to flash it again and then flash the official rom
Link to Hard SPL 1.22
Link to Official WM 6.1 WWE with ROM 1.65.29.25
how can i flash hard spl 1.22 from bootloader?
• power off yuor niki (Remove for a couple of seconds the battery)
• press and hold power and camera buttons,you must have (tree color) bootloader
• connect usb cable
• run ROMUpdateUtility.exe (or Nike CustomRUU.exe) in a folther with hardspl-1.22-nike.nbh
salvy.c.83,I can't flash hardspl, it's stop at 0%..help please..
salvy.c.83 said:
• power off yuor niki (Remove for a couple of seconds the battery)
• press and hold power and camera buttons,you must have (tree color) bootloader
• connect usb cable
• run ROMUpdateUtility.exe (or Nike CustomRUU.exe) in a folther with hardspl-1.22-nike.nbh
Click to expand...
Click to collapse
Don't you need an SPL Jump running to upgrade the SPL? But, if you can't get into an OS you can't run the jump exe.
You need to find a really old ROM hat only requires the HardSPL you have then flash that. Or try an official one? Or have you already tried that
Related
I flashed HardSPL 2.30olipro and it wont boot the OS when I reset, the screen stays black like its still off and the green light at the top stays on, I can still access the bootloader and use MTTY, I have tried flashing various ROMs and the "set 14 0" but nothing works, At the moment I have :
IPL-1.00
SPL-2.30.Olipro
Anyone have any ideas?
Well, it appears you can get to mtty...
Try Task 28 (this usually works when stuck in boot screen - not sure exactly where you are stuck)
or...
Try flashing a new ROM.
todd_jg said:
Well, it appears you can get to mtty...
Click to expand...
Click to collapse
Yea no problems getting into the bootloader and using MTTY
todd_jg said:
not sure exactly where you are stuck
Click to expand...
Click to collapse
I'm stuck as soon as I turn it on, blank screen like its still off and green light at the top is on the whole time, but not when i go to the bootloader.
Thanks for the help
My problem of noot being able to see any splashes and not being able to turn on for that matter is weird, Who knows a way that I can erase all of the phone totally except for the bits that cant be likle the SPL and IPL, Is there any way possible to flash someones dumped rom, and use the wlan fixing method to set yourself a new Mac adress etc.
In the memory map it says the Radio and bootloader are at "0x????????" does anyone know whats under the mysterious question marks?
deleted post
Korpse said:
My problem of noot being able to see any splashes and not being able to turn on for that matter is weird, Who knows a way that I can erase all of the phone totally except for the bits that cant be likle the SPL and IPL, Is there any way possible to flash someones dumped rom, and use the wlan fixing method to set yourself a new Mac adress etc.
In the memory map it says the Radio and bootloader are at "0x????????" does anyone know whats under the mysterious question marks?
Click to expand...
Click to collapse
Have you tried to reflash the HARDSPL?
binky11 said:
Have you tried to reflash the HARDSPL?
Click to expand...
Click to collapse
Thanks for helping me
It wont actually let me write over it because it has that protection on it to stop roms overwriting it with an older version, would it work (and be safe) to delete the SPL using the erase command then reset the hermes and write the SPL again?
Hi! i also got same problem, can still access bootloader and mtty only
Any solution that i can do? the mtty command " erase [StartAddr [Len]] " can it?
Cmd>task 28
Storage format start
Write Nand Success
dwBlockToWrite = 13
Storage start block: 610
Storage Total block: 326
Total Bad Block in CE: 0
NeedToEraseBlockStart: 623
NeedToEraseBlockEnd: 936
Storage format success
Cmd>checkimage
IPL CRC checksum = 0x856C952E
SPL CRC checksum = 0x738D6562
CE CRC checksum = 0x92C76E00
ExtROM CRC checksum = 0x2F8830F2
Radio Image CRC checksum = 0xB3F22A62
Thanks first.....
Korpse said:
Thanks for helping me
It wont actually let me write over it because it has that protection on it to stop roms overwriting it with an older version, would it work (and be safe) to delete the SPL using the erase command then reset the hermes and write the SPL again?
Click to expand...
Click to collapse
The SPL area is touchy. If you were to erase the Bootloader, I am not sure you would ever be able to flash anything, since it uses bootloader commands to do it. Check the MrVanx downgrade guides. There are instructions for overwriting the latest HardSPL. It is a two step process, first using SSPL. Give it a shot.
Im having to same problem,
IPL 1.04
SPL 2.30 Olipro
Cmd>task 28
Storage format start
Write Nand Success
dwBlockToWrite = 13
Storage start block: 462
Storage Total block: 474
Total Bad Block in CE: 0
NeedToEraseBlockStart: 475
Storage format success
Cmd>checkimage
IPL CRC checksum = 0xC1AC9D2F
SPL CRC checksum = 0x327DEB48
CE CRC checksum = 0x4E705577
ExtROM CRC checksum = 0x85083D45
Radio Image CRC checksum = Checksum: Wait interpreter timeout
0x0
Cmd>
when I try to reflash any rom I get an error, usually hangs around 12%
Hey guys,
Anyone got a resolution to this problem yet?
Heres whats happening:
When I turn on the device I get the green led light but nothing shows on the screen at all, I can still access the boot loader the normal way.
- Tried Task 28
- Can flash any ROM but doesn't fix issue at all
- Happened after i updated to HardSPL 2.30, but cant downgrade because I need access to the OS to use SSPL.
Thank you for any help
Same problem.
Hi,
don't know if this will work for you, but it did for me. the difference is that mine wasn't hardspl.
I had the same problem when i was trying to upgrade to WM6 a friends JasJam (i had a USB connection problem). i tried alot of flashing, and the only one that seemed to work for me was the Official I-Mate ROM i got from this thread:
http://forum.xda-developers.com/showthread.php?t=348436
and flashed it after going into the bootloader.
after flashing this, i loaded the hardspl v7 from this one.
http://forum.xda-developers.com/showthread.php?t=296722
and after that, flashing any ROM works perfectly.
Hope this helps.
I'm going to try that but I'm not sure if it will work.
I am already running:
IPL-1.00
SPL-2.30.Olipro
so it will not let me override it with HardSPLv7
Not sure if I can be of much help but I had the exact same problem after a flash, then just booted into the bootloader and loaded a ROM from my MiniSD card (CRCs Rom) and that seemed to fix my problem. I also have HardSPL 2.30 installed
try
cmd>set 16 0
Hope it works, normally when i get stuck in the bootloader its what i do, soft reset, plug it to usb run mty and do that comand. after it says write nand soft reset the device, it should load the os with no problems ^^
I have the same problem too. I ran the hermes unlocker v3a and after 100% it won't boot, but the green light turns on at the top. I can get into bootloader and MMTY. IPL 1.01 and SPL 1.4 Olipro
I'm a total noob so please somebody help!
He Guys,
Just my luck I have bought an HTC Tytn with the original Dutch rom and sim unlocked second hand.
I wanted to put a new Dutch rom from HTC on it but I keep on getting the ERROR [244] : INVALID MODEL ID but what I don`t understand is I have used the original Dutch rom from HTC. So I checked the device information and under the tab identity it says;
Model No.: H
Platform: PocketPC
IMEI: xxxxxxxxxxxxxxxxxxx
Shouldn’t the Model No. be HERM200?
Has anyone any suggestions in how I can solve this problem so I can flash any rom I wish.
I have tried al the cid unlock programs I could find and in bootloader it says;
H
IPL-1.01
H
SPL-1.40.Olipro
Thanks in advanced.
Use RAR to unpack the Original Dutch ROM.
Take the NBH file that you get when you unpack the ROM.
Put it in a folder with CUSTOM_RUU from Olipro.
Run CUSTOM_RUU and it will load up the ROM from the NBH file, bypassing the CID check. Should work
Thanks for the reply,
I have tried what you suggested but I still get ERROR [244] : INVALID MODEL ID I have also read these posts http://forum.xda-developers.com/showthread.php?t=322231&highlight=CUSTOM_RUU+from+Olipro and http://forum.xda-developers.com/showthread.php?t=322119&highlight=CUSTOM_RUU+from+Olipro and http://forum.xda-developers.com/showthread.php?t=309707&highlight=CUSTOM_RUU+from+Olipro and tried these suggestions but every time I get the error message. The radio update process was the same for me it will go to 7% and then give the message ERROR [244] : INVALID MODEL ID.
I have also tried the HTC_Hermes_SIM_CID_Unlock_v3a and Hard-SPL-V7 but still get the error message.
I hope I’m doing something wrong if not then I hope you have a new suggestion.
Thanks in advance.
Please set your device in BOOTLOADER MODE and post here your IPL / SPL versions.
Junner2003 said:
Please set your device in BOOTLOADER MODE and post here your IPL / SPL versions.
Click to expand...
Click to collapse
Did you read first post?
VivaErBetis said:
Did you read first post?
Click to expand...
Click to collapse
Ups, missed the bottom - thought it is the signature already! Sorry, haven't had my coffee yet!
Well, looks like the device is CID unlocked!
How about trying to flash an entire cooked ROM?
i would suggest the following:
flash a cooked rom (any)
see if that makes any difference to your model id
then try and flash the native dutch rom
good luck
Hi Guys,
As you suggested I tried a cooked rom the Hermes_WM6_vanilla still get the same error message when I put my device manually in boot loader it shows;
H
IPL-1.01
H
SPL-1.40.Olipro
But as soon as I try an official or cooked rom it shows;
H
IPL-SSPL by des
H
SPL-1.09.ds
I’m now trying Schaps_WM6Pro_WWE_4.00_Full_Beta3.exe and choose for auto detect and it said 1.40 Olipro and in boot loader it shows;
H
IPL-1.01
H
SPL-1.40.Olipro
And after 1% I got the ERROR [244] : INVALID MODEL ID message again.
I think my options are getting slim.
Your ModelID is stored on NAND and can be edited quite trivially (mostly).
how it got corrupted I don't know, however, the important question is; can you get into the OS?
He Olipro,
The device it zelf works perfect I can go anywhere I want even in the OS.
Just lead the way.
Changing Model ID
I have a similar problem in that my Model ID got corrupted during a radio upgrade. I now get the same error (244) and am stuck on SPL2.10 and can't downgrade to fix it. Can anyone tell us how to manually change the model ID in the NAND?
Much appreciated.
Dumping NAND
Ok, I'm a relative newbie so appologies before I get flamed. Thanks Olipro for giving me a clue.
I have now got spl 2.60 on my device but am unsure how to dump the NAND. I've worked out how to dump the 3 partitions from the device to dump the OS but am still unclear which part of the device is the NAND. I've read the Wiki on the memory map but am still not too sure.
Anyone able to give me simple instructions to dump the NAND and once I've done that where abouts is the ModelID stored? Do I do this using mtty?
Thanks in advance.
http://forum.xda-developers.com/showthread.php?t=322225
NAND Dump
Thanks Drummer for pointing me in the right direction.
Ive done this bit:
BTW, if you want to do a full backup of you FULL eeprom nand at any time, connect as before and type these commands:
plink HERMES > full.nb (hit ENTER twice)
task 32 (hit ENTER once and only once from now on after every command)
password 0000000000000000 - My device password is BsaD5SeoA which I used instead.
set 1e 1
rbmc me.txt 50000000 7fff800
watch your file grow to 128 MB.
It creates a full.nb file but it stays at 1k!!
** Note I have copied the bootloader file for spl 2.60 on my Hermes and ran that so I can now use that versino instead of the 2.10 thats on my device if that makes a difference and have tried with no joy with either version. Yes I know it says to use 2.30 but I can't work out how to get that on my device due to the ModelID error.
The Model number is contained within the herm1.nb file that was posted by BusStop in that thread. No need for complete NAND reflashing, only that section. You'll see it using a Hex Editor. You should write down your WiFi MAC addess, so you can edit it before flashing the file with the corrected Model number. Now you just have to figure out how to get SPL 1.01 MFG on your device...
Thanks Drummer. I did try flashing the herm1.nb file but of course as I do not have SPL 1.01 MFG it gievs an error. I'll keep trawling through the site and see if I can work out how to get SPL 1.01 onto my device. I'm not going to let this damn device beat me.
Ok so I worked out how to get the ModelID using getdevicedata. Used nbhtool to create a vaild nbh using the ModelID I'd just got and used the spl from 2.30 and it updated that fine.
Excellent.
However did the same with the MFG1.01 and flashed it and......
I now have a dead brick, no power and no response form usb. Time to get a replacement device.
Thanks for all the help I've had. I'm sure it should have worked.
1.) Remove battery
2.) Connect Hermes to charger or USB
3.) Insert the battery while Hermes is connected to charger
4.) Red light should turn Amber
5.) Soft Reset
Thanks for the advice Drummer however:
1.) Remove battery
2.) Connect Hermes to charger or USB
3.) Insert the battery while Hermes is connected to charger
4.) Red light should turn Amber - Nope red light goes out!
Mne shows HHHHHHH
Hi all, i've upgraded my radio and after my model id changed to H.
So, reading some posts i've used NBHTOOL.
1.I've decompiled an original Italian ROM
2.i've obtained a custom nbh selecting only OS and EXTROM and changing my Model number.
3. after that i've flashed the nbh resulting into a write error at 84% and a bricked htc.
Luckily i was able to reflash roms and i processed to second experiment.
I've made a custom rom with only the os, and it WORKED!
so my questions are:
1. can i use my htc even if my external rom isn't flashed (it cames from an old Schaps 4.0 succesful flash)
2. It is safe to proceed installing bootloader SPL using the nbhtool like i did with the os?
In that case i will be able to fix the model id problem by flashinh spl 1.01 and using the wireless fixing method you posted..
Thanks in advance for your reply!
Hi
From my understanding the Ext rom is mainly used for carriers to install there specific addons and customizations so it shouldn't be a problem.
As you can see I did flash spl 2.30 using this method and it worked fine ti was only when something whent wrong flashing 1.01 that my problem happened but I think that may be that I used an nbs file instead of an nb file from what I've read since.
Good luck.
Edit: Just noticed someone on this thread has managed it by going straight ot 2.60 http://forum.xda-developers.com/showthread.php?t=322225
well...
that didnt work :|
running vista ultimate sp1, following all the guides, trying to update to RUU Nike Radio 1.58.21.23,
had the RUU Nike Radio 1.58.16.27 installed...
everything went fine untill it came to 99%... it stalled and the install program told me to follow some
recovery steps, i did, but vista cant recognize the usb device... henche, i cant connect to the phone...
is there a place for drivers or so...??
please help out a noob...
anyone...??
when i start my phone i only get the different color screen, and it says:
Niki100
SPL-1.6.0000
CPLD-4
in the top right corner it says: RUUNBH
Ah easy ... Download MTTY disable Activsync USB Connection and start MTTY -> set Connection to USB -> if you see CMD> use the commando "boot"
Have you a Windows XP PC? Vista make some troubles!
Your device boot now! if your device make troubles ... flash a full rom with SPL, Radio and OS! Have you CID Unlock your device? HardSPL, USPL or SSPL? I want know to cross check!
Your SPL is very low ... i havent this version to test it with all radio roms.
will try this asap...
i used sspl, dont know if it is CID unlocked, think so...
ok...
did what you said, but what is suposed to happen...??
i get this in the log window of mtty:
boot
Fill RSVD information for block 288 to 309
Storage start sector=0x8940, total sector=0x12980
Storage start block=570, total block=1190
Total Bad Block in CE: 0
Erase physical block from 860 to 2032
si backup: Erase physical block from 2032 to 2048
No card inserted
OEMGetUpdateMode
OEMTranslateBaseAddress 23 80000000 80000000
IPLMSG:0x8:INFO: Loading image ...
IPLMSG:0x9:INFO: Jumping to image...
OEMLaunchImage 80000000
Jump to Physical Address 10300000
you say my spl is low, any way to update this...?
uhm ... realy bad!
what nike device is yours? can you say me your country and original os your device are?
i got it working again...
tried the mtty thing again and i booted, i flash with the hardspl thingy, and updating the rom now to the: RUU_Nike_HTCASIA_AUS_1.31.710.12_Radio_Nike_1.58.21.23_signed_Ship_PA
i bought mine in norway, december 2007
its alive
thank you for your help, you serously saved my day
^_^
try to flash radio again and tell me if you get the same problem again or not! its for debuging! i think ... some flash problems come from vista.
i used a wxp laptop, and flashed with the RUU_Nike_HTCASIA_AUS_1.31.710.12_Radio_Nike_1.58.2 1.23_signed_Ship_PA rom and radio, and it all works just fine
will try again with the updated radio as soon as i get home...
Hi Guys,
I'm from Germany and I have the following problem:
I wanted to flash a WM6-Rom onto my SDA 2 / HTC Hurricane.
I did everything that was described in the tutorial but at one point I have got a problem:
When it comes to opening mtty, I can't flash the Rom.
It says:
Download Fails !!!
OEMFlashWrite error(12)
Error : DownloadImage return error (code = 0xFFFFFFFF)
Click to expand...
Click to collapse
What to do now?
I have absolutely no idea.
And I would be very glad if somebody could help me to get ANY Rom onto my device.
I'm kind of frustrated right now.
See you.
Timops
it's to small information to say anything.
you must past whole communicates from Mtty (everything)
than we can say something about it
Alright.
Then I will try it again today and post the whole mtty log.
Perhaps you can do sth. with it.
But now I've got the T-Mobile-UK-Rom (WM2003) on my device.
But I really want WM6.
1- do you unlock phone from application lock?
2- do you change CID to 11111 ?
3- do you upgrade phone with latest SPL for hurricane (for hurricane WM6)
4- do you writing commands in mtty yourself? or copy/past? (copying doesn't work)
lazaj007 said:
1- do you unlock phone from application lock?
2- do you change CID to 11111 ?
3- do you upgrade phone with latest SPL for hurricane (for hurricane WM6)
4- do you writing commands in mtty yourself? or copy/past? (copying doesn't work)
Click to expand...
Click to collapse
1- I used the cert.cab. I think this is application unlocking
2- yes I did by using SPV-Services
3- I don't know, but I used PatchedRuu.exe (I think this is that)
4- yes I write them myself
I'll try in a few minutes and post the log if it doesn't work.
But don't hesitate to post any suggestions or information.
BTW: Is my English understandable?
Now this is my log from mtty:
info 2
GetDeviceInfo=0x00000002
+ SD Controller init
- SD Controller init
+StorageInit
CMD55 failed
+ SD Controller init
- SD Controller init
+StorageInit
CMD55 failed
HTCSSuperCID ' HTCE
Cmd>format BINFS
Format BinFS partition.
Format is completed!!
Cmd>l c:\ROM.bin
clean up the image temp buffer at 0x8C080000 Length 0x01C40000
MTTYDownloadImage "c:\ROM.bin"
:F=c:\ROM.bin
start download
SAddress 82040000Hh Length 02C00000h
Before flashing new image , formatting old OS is completed!!
Start flashing new image!!!
*checksum = 0, skip checking
OEMFlashWrite(82040000h,8C080000h,01C00000h)
Update BINFS offset 0x00000000 length 0x01C00000 ...
Update BINFS success.
*checksum = 0, skip checking
Image Download Finish
OEMFlashWrite(83C40000h,8C080000h,01000000h)
Update BINFS offset 0x01C00000 length 0x01000000 ...
Flash BINFS failed.
Download Fails !!!
OEMFlashWrite error(12)
Error : DownloadImage return error (code = 0xFFFFFFFF)
Click to expand...
Click to collapse
I think I know where the problem is:
I can't get into the bootloader correctly.
When the phone asks me if I want a IU (0) and I press the Zero-Button on the phone, nothing happens.
What to do now?
you must trying to success. maybes SPL was upgrade incorrect, go to bootloader and try to upgrade SPL by patched ruu again
I tried this so often but I don't give up!
I'll try again, maybe I'm lucky.
Who knows?
Where can i get this PatchedRUU ? I have the NBF File but i think a need the RUU program it self, but where to get it ?
here is PatcedRUU http://www.spv-developers.com/forum/attachment.php?attachmentid=65
wrong RUU!!! RUU from above will KILL your Hurricane!!
Above RUU will kill your Hurricane because it for Typhoon.
BTW: I had "CMD55 failed" error when using bad USB-cable... trying another cable made it disappear.
lazaj007 said:
you must trying to success. maybes SPL was upgrade incorrect, go to bootloader and try to upgrade SPL by patched ruu again
Click to expand...
Click to collapse
I have the same problem like Timops...Download Fails !!!
OEMFlashWrite error(12)
Error : DownloadImage return error (code = 0xFFFFFFFF)
I decide to try upgrade SPL..............but nothing...I get the "white background"
now what can I do....? USB connect not working...bootloader not working...maybe jtag?
I try to flash rom ENG to my NIKi
my version is 1.31.406
I read post "Nike SSPL, USPL and HardSPL" by jockyw2001
1. download the attached files
2. REMOVE SIM and SD CARDS !!
3. connect usb cable
4. copy sspl-1.16-nike.exe to your device and run it (usb cable must be connected!)
5. after a few seconds "USB" appears on the display
6. unplug and replug the usb cable
8. you can now flash the hardspl-1.15mfg-nike.nbh by running ROMUpdateUtility.exe from flash-uspl-niki
******* but it's still 0% and still boot loader screen*****
I Hard reset my NIKI but still bootloader and show
NIKI100
SPL-1.16.0000
CPLD-4
I try to flash this rom "RUU_Nike_HTC_WWE_1[1].13.405.01_Radio_Nike_1.58.11.07_signed_Test.exe"
It's 1% only and report error 262
"ERROR [262, 276, 284, 302] : UPDATE ERROR
This error occurs during the CE ROM code upgrade process.
Solution: If this happens, you can just soft-reset the device and run RUU again. The update process will then continue."
How to repair this
in post "http://forum.xda-developers.com/showthread.php?t=387217" by NetrunnerAT
"1. Download MTTY and connect via USB (dont forget do disable Activ Sync!!) us command Boot, to force a OS Boot!
2. After OS is Started ... Download SSPL and Copy it to your Phone ... please remove SD Card and SIM ... Start this Program!
3. Now you are in the Bootloader but it tells something about SPL 1.16Jump ... now you can Flash Hard SPL!!! If you doesnt see 1.16Jump you CAN'T Flash HardSPL!!
4. Now you can Flash my Dumped TIM Rom!!! "
I try this It show log
"boot
Fill RSVD information for block 288 to 309
Storage start sector=0xAF00, total sector=0x103C0
Storage start block=721, total block=1039
Total Bad Block in CE: 0
Erase physical block from 1011 to 2032
si backup: Erase physical block from 2032 to 2048
Card inserted
SDHW_EnablePowerOn
SDHW_ConfigGPIO
Cmd5 CMD_TIMEOUT
Cmd8 CMD_TIMEOUT
SD Init OK
SDFATChkConf: RhOpenFile() failed NIKECONF.txt
OEMGetUpdateMode
OEMTranslateBaseAddress 23 80000000 80000000
IPLMSG:0x8:INFO: Loading image ...
IPLMSG:0x9:INFO: Jumping to image...
OEMLaunchImage 80000000
Jump to Physical Address 10300000"
and still boot loader
how to fix it's
Thank' for reply
Please tell us ... what you have done before ... step by step!!!!
If you stay in the Bootloader and MTTY "boot" doesnt work, try the oemsbl with the command "cego"
NEXT ... what NIKI you have? German? UK? TIM? Vodovone branded?
You tell us not enough, too help you!
NetrunnerAT said:
Please tell us ... what you have done before ... step by step!!!!
If you stay in the Bootloader and MTTY "boot" doesnt work, try the oemsbl with the command "cego"
NEXT ... what NIKI you have? German? UK? TIM? Vodovone branded?
You tell us not enough, too help you!
Click to expand...
Click to collapse
Sorry For My Eng = =' I'm Thai girl.
I can't Remember lang before flash becouse I don't Know ^ ^ GER or Italy or Rus Lang
It's Not Eng Lang not Vodafone Brand
I'm new bie for this model . I have Dopod 818 pro It's Easy to flash I think Niki Is same
command "cego" notwork
Can I reflash any Office Rom?
What is SPL-1.16.0000 mean It's Hard SPL,SSPL or USPL
I Try to Put camera button and power button
and Use Mtty
boot
InitDisplay: Display_Chip=1
Card inserted
SDHW_EnablePowerOn
SDHW_ConfigGPIO
Cmd5 CMD_TIMEOUT
Cmd8 CMD_TIMEOUT
SD Init OK
SDFATChkConf: RhOpenFile() failed NIKECONF.txt
OSSIReadBack ++
Read SI data from flash success
tail signature match
Checksum match
UserStorageSIPreload ++
My NIKI Can boot and Use Now
I don't Know what Lang
" A Propos de
Windows Mobile 6 Profesional
Processeur : MSM7200-400Mhz
Memorie :101.67 Mo
Conecteur d'ext. :En cours d'utilisation
Informations de L'appareil
Version de Rom :1.31.406.09
Date de Rom :10/30/07
Version de Radio 1.58.16.27
Version de prot.. 25.61.30.03w
Is lang France?
@^ ^@
Hoorayyyyyyy
My phone is back
many thank's for NetrunnerAT
1. Download MTTY and connect via USB (dont forget do disable Activ Sync!!) us command Boot, to force a OS Boot!
2. After OS is Started ... Download SSPL and Copy it to your Phone ... please remove SD Card and SIM ... Start this Program!
3. Now you are in the Bootloader but it tells something about SPL 1.16Jump ... now you can Flash Hard SPL!!! If you doesnt see 1.16Jump you CAN'T Flash HardSPL!!
4. Now you can Flash my Dumped TIM Rom!!! "
and Now I Use rom TOM_Niki-Project_WM6[1].1_WWE_16keys_signed_Ship.exe
Many many Thank For XDA - Developers
http://www.pdamobiz.com/ <- its a Thai PDA Board!
The most errors on HTC Niki are simulare with HTC Polaris and HTC Kaiser!!!
I hope this helps!
my touch dual is lock at 3 color mode
Sorry for my english....
My niki is locked afther flash for unlock it (supercid)
I've tried to install a sspl and hardspl, but all have crashed at 95%
I've tried to install hardspl renaming the file nbh in NIKEIMG.nbh from sd, but this procedure have only send me message: loading......... and nothing all.....
At this moment my niki is stopped at 3 colors mode
Have you any idea for help me?
Many thanks to all
don't have any idea for help me?
i can use my niki for stop my door?
thanks
Works very well
This really helps me out!!!! Thanks to NetrunnerAT.
but the site is in thai language