So here is my situation:
I had a 3.27 radio with a 3.xx rom (one of the DCD roms). I wanted to get the 3.35 radio so i decided to flash to the SPRINT 3.35 rom, to do so i had to relock the phone so i used Titan Re-locker (which may have caused the whole problem) and now I am stuck at the SPL 1.06 screen.
I tried flashing older roms and still no luck.
I am currently with Telus and only flashed the SPRINT 3.35 rom to get the 3.35 radio off it. WHat do i do? I haven't bricked my phone right?
I have tried to flash Sprint 2.09 and SPRINT 2.17 roms and have failed. The bar goes up to 1% and then restarts the phone back to the SPL 1.06 screen for any flashes i try to do.
So here is my situation:
I had a 3.27 radio with a 3.xx rom (one of the DCD roms). I wanted to get the 3.35 radio so i decided to flash to the SPRINT 3.35 rom, to do so i had to relock the phone so i used Titan Re-locker (which may have caused the whole problem) and now I am stuck at the SPL 1.06 screen.
I tried flashing older roms and still no luck.
I am currently with Telus and only flashed the SPRINT 3.35 rom to get the 3.35 radio off it. WHat do i do? I haven't bricked my phone right?
Click to expand...
Click to collapse
Ok there's a WHOLE mess of problems with this post. First of all, if you read correctly in the kitchen thread, radio 3.35.04 is REQUIRED for any 3.x.x rom. 3.27 WILL not work. Second of all, you do not need to relock your phone when installing the 3.35 sprint rom, in fact, that's what caused it to break as the 1.06 bootloader will not flash or boot a 3.35 rom or radio. The only way to fix your problem right now is to flash the stock telus rom and radio using the microsd flashing method. Once that is complete, you need to unlock again with Olipro 2.40, and then run the sprint 3.35 update.
sux 2 B U. I highly doubt it is bt\ricked, you just dont know what U R doing.
This it what I did...
I did not need to relock. I started the sprint update with the phone booted up to the titan in Hard-SPL mode(miltucolor flash screen) . It reboots to the Hard-SPL several times to finish it and may pause several times. I just let it run. Keep an eye on it, it is done when it boots to a regular boot screen. Dont let it finish booting and then manually boot into Hard-SPL (PWR + Camera + reset with stylus) and flash DCD 3.0.4. I did the same process with the alltel update to get 3.37. You will be left with the bootscreens from the Sprint or Altel rom, but booting to DCD rom with 3.37 radio, GPS, exct....
Related
Ok here goes,
I have been using DCD rom and everything has been great.
olipro 2.40
3.27 radio
DCD 2.3.2 Rom
The problem started this morning after I ran the titan relocker to try and go back to a VZW rom/radio etc.
The relocker seemed to work fine, I am at the boot loader screen which states the following...
TITA100 ruunbh
spl-1.06.0000
cpld9
Looks normal to me, so I try to continue loading the vzw radio and then rom. When I run RUU after dropping the nbh file in the folder, I go through the motions and get a percentage screen on both my pc and the phone. It never goes above 0%. I get a communication error and have an option for recovery, which I tried and it didn't work. I dont have a microSD Card to flash from. Any Ideas?
Resolved
Found a util that would get me out of the boot loader cycle called titan_exitbl.exe. Re-Unlocked bootloader, reflashed dcd 2.3.2 rom, and reflashed radio 3.27 .
I have the same problem! There Are any ways of the decision?
I flashed both, same issue, no sound when dialing *228. If I try to turn on the speaker, it snaps and restarts. If I leave it going it will connect and about 30 seconds later it restarts.
Any suggestions?
More info please...... what were you running before? Have you unlocked the phone and upgraded the bootloader and radio?
I was running the stock rom before. I using the 3.27 radio and olipro 2.4 I did the bootloader, the rom then the radio. I unlocked the phone with Hard SPL 240. Do I need to relock?
You need to upgrade your radio to atleast 3.35.
yea get 3.35 or 3.37 radio
WAstarita said:
I was running the stock rom before. I using the 3.27 radio and olipro 2.4 I did the bootloader, the rom then the radio. I unlocked the phone with Hard SPL 240. Do I need to relock?
Click to expand...
Click to collapse
You need to read the ENTIRE section that DCD wrote in the 3.0.4 kitchen POST.... He clearly states you NEED the 3.35 or higher radio.... there are known issues with the "leaked, beta 3.27 radio" one of them is an audio issue....
You will only need to flash the SPINT or ALLTEL update. WITHOUT letting the customizations run..... Then DCD 3.0.4 will run fine for you....
I'd like to upgrade my VZW XV6800 to DCD's Titan 3.1.2 with radio 3.39.10, but have some questions. I've read the Wiki and FAQ several times through, but am having a hard time understanding the correct order of upgrading the radio and ROM.
I've successfully upgraded bootloader to 2.40 using Hard-SPL-MFG.exe
Do I next upgrade the radio? Or do I load DCD's 3.1.2 and then upgrade the radio? (After writing that out I think I would upgrade the radio...looking for confirmation.)
Radio or you will be screwed. I speak from experience. Get a SD card and use that method.
good advice on both accounts.
did the radio first, but was then unable to get past the bootloader and unable to connect w/ ActiveSync. followed the SD directions and now i'm running everything i wanted!
I Flashed ROM Then Radio
Tonight I just finished successfully flashing my phone for the first time. I updated the boot loader using titan_SPL_2.40-olipro.exe, then I attempted to update the radio but actually did not due to a mistake on my part, then I successfully updated the ROM to dcd_titan_3.1.2.exe. Upon a restart, I realized the radio was not updated based upon the Verizon splash screen so I re-entered the bootloader and eventually flashed the radio. Once I finished flashing the radio I restarted and was presented with WM 6.1 and a usable phone.
Easy Way
The easiest way i found was after the new bootloader to go and use the Alltel Stock ROM with the 3.39 radio. This will upgrade your radio without you having to call Verizon. Then load DCD's ROM. Again you should not have to call Verizon or mess with SD cards or anything.
The easiest way i found was after the new bootloader to go and use the Alltel Stock ROM with the 3.39 radio. This will upgrade your radio without you having to call Verizon. Then load DCD's ROM. Again you should not have to call Verizon or mess with SD cards or anything.
Click to expand...
Click to collapse
The Alltel rom has Radio 3.37.20, not 3.39.10.
schwillyd530 said:
The easiest way i found was after the new bootloader to go and use the Alltel Stock ROM with the 3.39 radio. This will upgrade your radio without you having to call Verizon. Then load DCD's ROM. Again you should not have to call Verizon or mess with SD cards or anything.
Click to expand...
Click to collapse
Also not everyone has to call Verizon. I have flashed once to stock, DCD 3.0.4 and DCD 3.1.20 and have yet to call or reenter anything.
Hey All,
i've been doing alot of reading here on xda and have played with and updated several WM devices. didnt want to start a thread but it was my last resort for help.
I've got an HTC 6800 - TITA100 , from Bell mobility. i'd like to upgrade it to DCD's most recent ROM. here's what i've been able to do:
-installed SPL 2.47 bootloader successfully.
-grabbed the 'RUU_signed.nbh' from DCD's 3.2.5 ROM & renamed it to TITAIMG.nbh, placed on properly formatted sd card.
-sent the phone into bootloader (power,camera,reset buttons), it sees the img on the card, press the button to install, and it installs successfully.
this is where the problem comes up. after installation, i reboot the phone, goes to the first splash screen which still shows the Bell logo, and at the bottom i notice D: 3.2.5 , then it goes to a bell splash screen with no other writing, and just sits there.. doesnt get past this splash screen.
what i can do at this point is put the phone back into bootloader, and install the one of the htc/bell ROMs, reboot, and get into the OS without any problem.
is there some steps i'm missing? besides installing the SPL 2.xx bootloader, should something else happen before putting the cooked ROM ?
any help is appreciated !! thanks
What radio are you using?
i downloaded this radio to use: 3.42.50
should the radio be installed before trying to install DCDs OS? i may have tried that but dont remember 100%.
to get it functioning again (OS) i use the bell/HTC official rom, which i notice before the bootloader installs it, it shows that it will update bootloader, 2 splashscreens, radio, OS, etc...
incredible.. had tried so many things. flashed the radio, then tried flashing DCD and it boots fine now.. thought i had tried that already..
profets said:
incredible.. had tried so many things. flashed the radio, then tried flashing DCD and it boots fine now.. thought i had tried that already..
Click to expand...
Click to collapse
Yes. It's always good to load the Radio first. I currently cooked my own NBH file that includes the splash screens, 3.42.50 radio, and DCD 3.2.5 rom. That way I can do it all in one easy flash.
nitro66215 said:
Yes. It's always good to load the Radio first. I currently cooked my own NBH file that includes the splash screens, 3.42.50 radio, and DCD 3.2.5 rom. That way I can do it all in one easy flash.
Click to expand...
Click to collapse
interesting idea.. care to share that nbh? i guess it shouldnt be hard for someone to cook it up themselves if they have all the needed components
Bump!
I'm having the same issue. I'm with Bell Mobility.
I updated the bootloader with nueSPL Titan 2.47 pack and successfully installed the radio.
Then the device remains stuck on the blue bell loading screen. I've tried radio versions 3.35.04, 3.42.40 and 3.42.50.
I'm totally stumped on how to resolve this. Where do I find the RUU_signed.nbh?
Any advice would be greatly appreciated.
Thank you!!
Press and hold Power and Camera and then press the reset button.
This puts it in Bootloader mode, then run the DCD's rom or Kitchen, when the Rom Update Utility starts, it will detect your phone and flash the rom.
Once the flash is finished, the phone should boot normal, and you can flash any other custom rom to the phone. It's just important to do the first 3 flashes correctly, then afterwards the rest is easy.
BTC
Anyone encountered this error before? It gets to 8% and then phone reboots and I get this on my PC screen. It says Error [328] (see attached image)
I am using Radio 3.37.75 (verizon), and my bootloader shows 2.40 Olipro
Any ideas?
Try this RUU it is version 3.16.4.3.
Yes, thats the version that I am using. I think... when I run it, it says 3.16.4.3 in the window title bar. (see screen shot)
EDIT: I tried it anyways, and I got the same thing. Do I have the right bootloader? Would a different one help?
what are you trying to flash
trying to flash my verizon xv6800 (which has an old dcd rom on it, radio 3.27 i think) to the new radio: 3.37.75.
Then i will flash with a newer dcd or ryan mogul rom.
wildcard said:
trying to flash my verizon xv6800 (which has an old dcd rom on it, radio 3.27 i think) to the new radio: 3.37.75.
Then i will flash with a newer dcd or ryan mogul rom.
Click to expand...
Click to collapse
Just follow my post here and only use the files and Radios that I provide. Make sure you read a few times so you understand, and dont skip anything. Most important based on what I have read in this thread. Use only the radios I provide on my share site and take your time paying close attention.
http://forum.xda-developers.com/showpost.php?p=3687027&postcount=144
Thanks, I'll do it exactly like that. I will keep you posted. I have to get a new micro SD card, I only have an SDHC 8 GB
The radio can be updated via usb. I do it all the time. But it does hard reset the phone in the process.
I would try a newer radio like 3.42.40. http://wiki.xda-developers.com/index.php?pagename=TitanRadioROMs
I got my radio from there and have no problems updating the radio with ruu.
I followed the directions exactly like in Ryan's post mentioned above, (used USB instead of SD card), and it works!
Fully functional. I used Radio 3.42.02 (somewhere I saw that it was recommended over the others, went with it to be safe). Then Flashed Ryan Mogul Rom 2.2 Heavy.
Thanks everyone!
drewcam888 said:
I would try a newer radio like 3.42.40. http://wiki.xda-developers.com/index.php?pagename=TitanRadioROMs
I got my radio from there and have no problems updating the radio with ruu.
Click to expand...
Click to collapse
i have spl olipro-2.40, rom dcd 3.2.6 and want to upgrade radio to 3.42.50 using usb. should i downgrade spl to 1.20 before upgrade the radio? or i stick with current config and update the radio using RUU?
Still cant load radio
Obtained 6800 originally Alltel, not sure which radio, Had Olipro 2.40 installed, would hang on Alltel splash screen.
Could not get any RUU loads to complete (from USB or SD card), usually would fail around 50%.
Eventually was able to get RyanMogul 3.1 Cricket (lite) to load, but shows no radio and eventually screen goes blank. Never goes into active Sync mode.
We force boot loader mode and try and load several radios including Titan_Radio_ROM_3.42.50.Alltel.rar, Titan_Radio_ROM_3.35.04,
but keep Getting error 328 from RUU when I try to load a radio..
tried RyanMoguls "Here is a fix for GPS for all you VX6800 users that gps will not function!!", but cant run relocker because no active sync connection.
Stock Verizon ROM RUU also gets error 328.
Any ideas.