I flashed both, same issue, no sound when dialing *228. If I try to turn on the speaker, it snaps and restarts. If I leave it going it will connect and about 30 seconds later it restarts.
Any suggestions?
More info please...... what were you running before? Have you unlocked the phone and upgraded the bootloader and radio?
I was running the stock rom before. I using the 3.27 radio and olipro 2.4 I did the bootloader, the rom then the radio. I unlocked the phone with Hard SPL 240. Do I need to relock?
You need to upgrade your radio to atleast 3.35.
yea get 3.35 or 3.37 radio
WAstarita said:
I was running the stock rom before. I using the 3.27 radio and olipro 2.4 I did the bootloader, the rom then the radio. I unlocked the phone with Hard SPL 240. Do I need to relock?
Click to expand...
Click to collapse
You need to read the ENTIRE section that DCD wrote in the 3.0.4 kitchen POST.... He clearly states you NEED the 3.35 or higher radio.... there are known issues with the "leaked, beta 3.27 radio" one of them is an audio issue....
You will only need to flash the SPINT or ALLTEL update. WITHOUT letting the customizations run..... Then DCD 3.0.4 will run fine for you....
Related
edit: as a result of a few people possibly bricking their devices, i have removed the standalone radio update.
at this time the best method of obtaining radio 3.35.04 is to flash the entire sprint 3.35 rom update.
Whoa. What are changes?
will this work on a Verizon one? or is it just Sprint?
DCD,
Getting an error on installation. RUU hangs at 9% then gives me Error[328] INvalid command, The update utility cannot be used for your PDA phone. Please check your update utility. I am running Olipro-2.40. Vz user. No issues in the past with upgrading rom or radio. Have been running leaked radio and both yours and No2Chem's roms.
Thoughts
okay so im seeing all kinds of misc threads around about this radio but everything is specific to Sprint...
no one can verify if this works with Verizon?
Anyone even know what the difference in the radio is from 3.27?
please excuse my ignorance, but I just want to make sure that if I'm already running one of your roms (2.3.1) that all I need to do is flash this radio. Is that right, or do I need to reflash the rom as well?
I am also getting the error at 9%. I have tried flashing about 5 times all with the same result.
Downloading the RADIO now... I've got DCD's 2.3.2 (modified a bit) ROM... will report once I get the Radio installed.... I am very excited.
weird, i had dcd 1.7.1 / radio 1.59.10a / spl-1.20-olipro
flash went fine
if you guys keep getting errors ill investigate further
vossco32 said:
I am also getting the error at 9%. I have tried flashing about 5 times all with the same result.
Click to expand...
Click to collapse
So you're just doing the radio and not the main ROM, correct? And are you just launching the updater or manually putting the phone into bootloader mode first?
I have your 2.3.2 release, 3.16 radio, and SPL-2.40.0lipro and I am getting the error. I will try a few more times. I did notice that the led flashes red right after it fails and reboots.
I am doing just the radio, and I have tried it both ways with the phone in bootloader and without.
Yep. Also getting the error here... I'm using DCD 2.3.2 ROM.
Still no luck either, running No2Chem 5049, 3.16 radio and 2.40. Extracted your radio and it is no different on 3 different RUU's, the same for the radio straight from the Sprint release.
rajuabju said:
Yep. Also getting the error here... I'm using DCD 2.3.2 ROM.
Click to expand...
Click to collapse
Me three, on my VZW 6800 with latest DCD and test Radio ROM.
Is the first post saying that I can use the New rom (released today) with olipro 2.40?
Yes I am getting the error at 9% also. Bummer.
dcd1182 said:
weird, i had dcd 1.7.1 / radio 1.59.10a / spl-1.20-olipro
flash went fine
if you guys keep getting errors ill investigate further
Click to expand...
Click to collapse
I flashed from 1.7.0 / radio 1.40 / spl-1.20
did spl 2.40 -> radio -> dcd 2.3.2 rom
no problems... except data is throwing invalid username again.. which is typical after a radio change.. just need to call verizon again
Same on 9%
I am also getting the error at 9%
VZW user with Olipro 2.40 and DCD 2.3.2 ROM
Edit: I have tried from both bootloader and with phone completely booted up.
l33tlinuxh4x0r said:
Is the first post saying that I can use the New rom (released today) with olipro 2.40?
Click to expand...
Click to collapse
No. That's already discussed in the thread on the new ROM (and in the ppcgeeks.com thread on the same topic). Here, we're talking about success (or lack thereof) in flashing just the extracted radio so that it can be used with custom ROMs and/or with non-Sprint phones.
David
Ditto
Thanks dcd, but getting same error at 9%...running NexVisions Hybrid, 2.40 etc.
So here is my situation:
I had a 3.27 radio with a 3.xx rom (one of the DCD roms). I wanted to get the 3.35 radio so i decided to flash to the SPRINT 3.35 rom, to do so i had to relock the phone so i used Titan Re-locker (which may have caused the whole problem) and now I am stuck at the SPL 1.06 screen.
I tried flashing older roms and still no luck.
I am currently with Telus and only flashed the SPRINT 3.35 rom to get the 3.35 radio off it. WHat do i do? I haven't bricked my phone right?
I have tried to flash Sprint 2.09 and SPRINT 2.17 roms and have failed. The bar goes up to 1% and then restarts the phone back to the SPL 1.06 screen for any flashes i try to do.
So here is my situation:
I had a 3.27 radio with a 3.xx rom (one of the DCD roms). I wanted to get the 3.35 radio so i decided to flash to the SPRINT 3.35 rom, to do so i had to relock the phone so i used Titan Re-locker (which may have caused the whole problem) and now I am stuck at the SPL 1.06 screen.
I tried flashing older roms and still no luck.
I am currently with Telus and only flashed the SPRINT 3.35 rom to get the 3.35 radio off it. WHat do i do? I haven't bricked my phone right?
Click to expand...
Click to collapse
Ok there's a WHOLE mess of problems with this post. First of all, if you read correctly in the kitchen thread, radio 3.35.04 is REQUIRED for any 3.x.x rom. 3.27 WILL not work. Second of all, you do not need to relock your phone when installing the 3.35 sprint rom, in fact, that's what caused it to break as the 1.06 bootloader will not flash or boot a 3.35 rom or radio. The only way to fix your problem right now is to flash the stock telus rom and radio using the microsd flashing method. Once that is complete, you need to unlock again with Olipro 2.40, and then run the sprint 3.35 update.
sux 2 B U. I highly doubt it is bt\ricked, you just dont know what U R doing.
This it what I did...
I did not need to relock. I started the sprint update with the phone booted up to the titan in Hard-SPL mode(miltucolor flash screen) . It reboots to the Hard-SPL several times to finish it and may pause several times. I just let it run. Keep an eye on it, it is done when it boots to a regular boot screen. Dont let it finish booting and then manually boot into Hard-SPL (PWR + Camera + reset with stylus) and flash DCD 3.0.4. I did the same process with the alltel update to get 3.37. You will be left with the bootscreens from the Sprint or Altel rom, but booting to DCD rom with 3.37 radio, GPS, exct....
Has anyone here SUCCESSFULLY downgraded the PRL on their XV6800 when using NueSPL 2.47 ?
I remember in the past people, including no2chem himself saying that downgrading SPL is a huge risk and may brick your device, so I thought I'd ask around.
I've been unable to remove the PRI from my device after doing the MR1 update.
Using tools like HTC GPS Tool, I see output from the GPS, but it never sees any satellite.
I did the Verizon AGPS fix that GC14 posted and I had some thoughts on the issue.
I was wondering if it is making it worse to have done the AGPS fix because of not having a data plan (I use Wi-Fi only).
Current Setup:
OS ROM: DCD 3.2.6 (Kitchen'd)
RADIO: 3.42.40
PRL: 2.03_002
SPL: NueSPL 2.47
Any ideas, input, comments, suggestions, etc?
scrawnyb said:
Has anyone here SUCCESSFULLY downgraded the PRL on their XV6800 when using NueSPL 2.47 ?
I remember in the past people, including no2chem himself saying that downgrading SPL is a huge risk and may brick your device, so I thought I'd ask around.
I've been unable to remove the PRI from my device after doing the MR1 update.
Using tools like HTC GPS Tool, I see output from the GPS, but it never sees any satellite.
I did the Verizon AGPS fix that GC14 posted and I had some thoughts on the issue.
I was wondering if it is making it worse to have done the AGPS fix because of not having a data plan (I use Wi-Fi only).
Current Setup:
OS ROM: DCD 3.2.6 (Kitchen'd)
RADIO: 3.42.40
PRL: 2.03_002
SPL: NueSPL 2.47
Any ideas, input, comments, suggestions, etc?
Click to expand...
Click to collapse
Downgrading SPL? You can do that without any problem. PRL? That's a different story. But yes. You can do that as well. The setup you have, I have successfully got GPS working. Have you followed the thread on this?
nitro66215 said:
Downgrading SPL? You can do that without any problem. PRL? That's a different story. But yes. You can do that as well. The setup you have, I have successfully got GPS working. Have you followed the thread on this?
Click to expand...
Click to collapse
I've been following a few threads in here on the issue.
Which one(s) are you specifically talking about?
None of them have truly helped me yet. I can't get GPS locks using the official verizon radio (3.37.71 or whatever) nor 3.42.40 with the new PRI, but I had it working with the same setup on the OLD PRI using Olipro 2.40.
If you have already updated to MR1 and locked down the GPS hardware on your device, you could try this out instead of trying to unlock the GPS hardware:
http://forum.xda-developers.com/showthread.php?t=424387
Currently, this needs you to be on MR1 to work. Including the MR1 GPS driver may allow it to work on a custom ROM if you want to try building your own, though that has yet to be tested.
Skywing said:
If you have already updated to MR1 and locked down the GPS hardware on your device, you could try this out instead of trying to unlock the GPS hardware:
http://forum.xda-developers.com/showthread.php?t=424387
Currently, this needs you to be on MR1 to work. Including the MR1 GPS driver may allow it to work on a custom ROM if you want to try building your own, though that has yet to be tested.
Click to expand...
Click to collapse
still not what I'm looking for.
I'm going to try unlocking my device and flashing the stock ROM, letting customizations run, then unlocking + then flashing the new VZW update and not running customizations, then going to DCD 3.2.6 again
sorry for the double-post, but I decided to do what I said in the last post.
I downgraded my SPL just fine using the Titan Relocker (not the one that puts you at 2.07 SPL, the one that puts you at 1.xx) then flashed on Stock VZW, then Olipro 2.40, then my kitchened DCD 3.2.6 ROM.
No bricked device.
I did notice my phone went into ROAMING when I flashed on the Stock ROM, but I didn't bother trying to call out, I was a man on a mission, and just kept going.
I did *228 option #1 when I got into 3.2.6 again, didn't need a new A-Key or anything.
GPS is STILL not working, as the PRI version stuck somehow.
*sigh* Problem not resolved... and I wasn't having any luck with doing the RadioRefurbish method either.
Any ideas?
Hello guys, I have a little bit of a problem, and I am hoping that you guys can help me out. About 10 months ago I upgraded from my stock ROM to dcd's 2.3.2. rom and 3.27.00 radio. Every thing went fine, loaded up 2.40 olipro and the installation went perfect. Now last month I saw that dcd came out with 3.2.6 and wanted to upgrade my rom and radio, but this is were i'm running into problems. I was able to flash the 3.2.6. rom, but I am unable to flash the radio. I have searched up and down these forums and checked out the wiki's and havn't been able to find a solution. So now all i'm left with is a phone that can't make a phone call but is still able to send sms messages. If anyone has any helpful tips or even a solution to my problem it would be much appricated.
I thought the 3.27 radio works with 3.2.6. What is happening when you try to flash the radio? and what method are you using to flash it (SD card or pc)? Also when you bootup the phone does it say 3.27 radio still? I believe all the newer DCD roms need a carrier cab have you installed the cab? I'm pretty sure the phone won't be able to make calls without the cab installed. 1 more Q what service do you have?
shield001 said:
I thought the 3.27 radio works with 3.2.6. What is happening when you try to flash the radio? and what method are you using to flash it (SD card or pc)? Also when you bootup the phone does it say 3.27 radio still? I believe all the newer DCD roms need a carrier cab have you installed the cab? I'm pretty sure the phone won't be able to make calls without the cab installed. 1 more Q what service do you have?
Click to expand...
Click to collapse
When I flash the radio it goes to 8% flashes a red light and then resets. I have also tried both methods of flashing but none works. When I bootup the phone it does still say 3.27 as the radio. I have also tried to install a carrier cab but have had no luck.
Try updating to Hard SPL 2.47
The 3.27 Radio is NOT compatible with ANY DCD version 3.X and higher..... Have you read the Wiki? Can you flash the radio using the SD card method? All of your questions have answers in the Wiki.....
You should flash back to 2.3.2. Go into the bootloader(tri-color screen) and then flash 2.3.2 to the phone..... reboot it.... it should load up ok.... If this works for you to this point, you have several options to upgrade the radio ..... Read the Wiki....
azclown said:
The 3.27 Radio is NOT compatible with ANY DCD version 3.X and higher..... Have you read the Wiki? Can you flash the radio using the SD card method? All of your questions have answers in the Wiki.....
You should flash back to 2.3.2. Go into the bootloader(tri-color screen) and then flash 2.3.2 to the phone..... reboot it.... it should load up ok.... If this works for you to this point, you have several options to upgrade the radio ..... Read the Wiki....
Click to expand...
Click to collapse
I looked over the wiki again and was able to re-flash to 2.3.2. Thanks for your help guys.
Anyone encountered this error before? It gets to 8% and then phone reboots and I get this on my PC screen. It says Error [328] (see attached image)
I am using Radio 3.37.75 (verizon), and my bootloader shows 2.40 Olipro
Any ideas?
Try this RUU it is version 3.16.4.3.
Yes, thats the version that I am using. I think... when I run it, it says 3.16.4.3 in the window title bar. (see screen shot)
EDIT: I tried it anyways, and I got the same thing. Do I have the right bootloader? Would a different one help?
what are you trying to flash
trying to flash my verizon xv6800 (which has an old dcd rom on it, radio 3.27 i think) to the new radio: 3.37.75.
Then i will flash with a newer dcd or ryan mogul rom.
wildcard said:
trying to flash my verizon xv6800 (which has an old dcd rom on it, radio 3.27 i think) to the new radio: 3.37.75.
Then i will flash with a newer dcd or ryan mogul rom.
Click to expand...
Click to collapse
Just follow my post here and only use the files and Radios that I provide. Make sure you read a few times so you understand, and dont skip anything. Most important based on what I have read in this thread. Use only the radios I provide on my share site and take your time paying close attention.
http://forum.xda-developers.com/showpost.php?p=3687027&postcount=144
Thanks, I'll do it exactly like that. I will keep you posted. I have to get a new micro SD card, I only have an SDHC 8 GB
The radio can be updated via usb. I do it all the time. But it does hard reset the phone in the process.
I would try a newer radio like 3.42.40. http://wiki.xda-developers.com/index.php?pagename=TitanRadioROMs
I got my radio from there and have no problems updating the radio with ruu.
I followed the directions exactly like in Ryan's post mentioned above, (used USB instead of SD card), and it works!
Fully functional. I used Radio 3.42.02 (somewhere I saw that it was recommended over the others, went with it to be safe). Then Flashed Ryan Mogul Rom 2.2 Heavy.
Thanks everyone!
drewcam888 said:
I would try a newer radio like 3.42.40. http://wiki.xda-developers.com/index.php?pagename=TitanRadioROMs
I got my radio from there and have no problems updating the radio with ruu.
Click to expand...
Click to collapse
i have spl olipro-2.40, rom dcd 3.2.6 and want to upgrade radio to 3.42.50 using usb. should i downgrade spl to 1.20 before upgrade the radio? or i stick with current config and update the radio using RUU?
Still cant load radio
Obtained 6800 originally Alltel, not sure which radio, Had Olipro 2.40 installed, would hang on Alltel splash screen.
Could not get any RUU loads to complete (from USB or SD card), usually would fail around 50%.
Eventually was able to get RyanMogul 3.1 Cricket (lite) to load, but shows no radio and eventually screen goes blank. Never goes into active Sync mode.
We force boot loader mode and try and load several radios including Titan_Radio_ROM_3.42.50.Alltel.rar, Titan_Radio_ROM_3.35.04,
but keep Getting error 328 from RUU when I try to load a radio..
tried RyanMoguls "Here is a fix for GPS for all you VX6800 users that gps will not function!!", but cant run relocker because no active sync connection.
Stock Verizon ROM RUU also gets error 328.
Any ideas.