Hi guys,
Today I tried to upgade my prohet to wm6. I used crystal v4 rom and followed the instructions from the sticky topic:
http://forum.xda-developers.com/showthread.php?t=350033
Everything went well and the process ended with 100% upload. However after flashing the screed went red,green blue and the only things on the display are:
"IPL 2.10.001
SPL 2.10.001"
I tried to restart the phone and to hard reset it but the screen is always the same.
What can I do about it?
I managed to upload RUU_Prophet_220734_2207114_024721_NVID rom and my prophet works again. Subject to be closed.
kordi666 said:
I managed to upload RUU_Prophet_220734_2207114_024721_NVID rom and my prophet works again. Subject to be closed.
Click to expand...
Click to collapse
If you flash using the "NEW" method, be sure that your SPL is 2.GX.4PDA before flashing the ROM (you have a G4 device, so 2.G4.4PDA.).
kordi666 said:
Hi guys,
Today I tried to upgade my prohet to wm6. I used crystal v4 rom and followed the instructions from the sticky topic:
http://forum.xda-developers.com/showthread.php?t=350033
Everything went well and the process ended with 100% upload. However after flashing the screed went red,green blue and the only things on the display are:
"IPL 2.10.001
SPL 2.10.001"
I tried to restart the phone and to hard reset it but the screen is always the same.
What can I do about it?
Click to expand...
Click to collapse
it normal. i suppose everyone has done the same.
but there is the solution but at first it is suggested:
DON'T PANIC
give a look to my old post here.
http://forum.xda-developers.com/showthread.php?p=1739879#post1739879
i found useful the guide of gullum that i'll never stop to thank.
don't warry you can restore everything.
jork
jork said:
it normal. i suppose everyone has done the same.
but there is the solution but at first it is suggested:
DON'T PANIC
..
Click to expand...
Click to collapse
also you can have a look to the link @ my signature ^_^, simple and helpful .....
Related
ok guys......i am sure there is a post some where bout this....but i did search alot before postin a new thread here.....basically the problem i have is just obvious ERROR 101 : CONNECTION ERROR, ive got a XDA II with wm2003se by mysteryman......as i am selling this XDA II in a day or two i wanted to downgrade to the official rom thats been released by o2 thats 1.7 something so i started the downgrade process....but i didnt notice and realize.....that i was not suppose to take out the adaptor's cable from the cradle......as i did that the process failed and now after tryin many times to downgrade after resetting hard resetting.....i have only been unsuccessful.....
just to let you guys know after alllll this i tried hard reset no use......screen is stuck at bootloader, where the bootloader is sayin version 1.72.00WWE (thats the official rom release)......
same result after a soft reset toooo
NEEEEEED HELP ASAP......URGENT !!
regards
jeetz
mate,
did you try reinstalling the upgrade / downgrade after the reset?
cheers
I am sure the "launch rom" was posted by O2 for this purpose, I cant remember the link for it but O2 hosts it. It was posted to give a recovery solution when an upgrade go's awry.
Robson said:
mate,
did you try reinstalling the upgrade / downgrade after the reset?
cheers
Click to expand...
Click to collapse
yeppp
tried reinstalllllin the upgrade thats wm2003se also tried the official released v1.7 but no luck....tried both.....soft and hard resets.....
any other suggestions...?
cruisin-thru said:
I am sure the "launch rom" was posted by O2 for this purpose, I cant remember the link for it but O2 hosts it. It was posted to give a recovery solution when an upgrade go's awry.
Click to expand...
Click to collapse
can you plz try to get the link for me
or is this the link you are talkin bout http://www.my-xda.com/xda2_soft3.html
http://www.my-xda.com/xda2_soft3rom.html
http://music.o2.co.uk/xrange/download.asp?f=Xda_II_172181_Final.exe
if these are the links then ive tried the final release of an official rom from here and its givin same error 101......and cant find any page or link where it says if the upgrade process goes wacko follow these links.....
regards
jeetz
O2
Ensure that your battery has juice. Remove it and charge separately via cradle battery slot. Once full pop it back in and confirm that the red limit switch is properly closed.
Hit Green+DPad+Red+Power+Reset to get into BootLoader mode. Shove it back into the cradle and flash with the ROM linked below. In case after flashing soft reset does not work attempt hard reset that should do the trick.
After that you can flash your Xda II to your heart's content.
:arrow: Default
Re: O2
[Krueger said:
Dr.Stein]Ensure that your battery has juice. Remove it and charge separately via cradle battery slot. Once full pop it back in and confirm that the red limit switch is properly closed.
Hit Green+DPad+Red+Power+Reset to get into BootLoader mode. Shove it back into the cradle and flash with the ROM linked below. In case after flashing soft reset does not work attempt hard reset that should do the trick.
After that you can flash your Xda II to your heart's content.
:arrow: Default
Click to expand...
Click to collapse
you da man (Y)......
entered bootloader mode.....but didnt download the link (rom you posted) directly goin for the official rom......and so far so good...its upgrading rom image......says 2% thanks alot mate.....
regards
jeetz
Hi,
I have a G3 Prophet, I did flash it with WM6 before & it worked but now every time i try to flash with [pdaviet] 4.0.0.0.4s_pv or other WM6 roms i get the same freakin error " Could not update itsutils.dll to the current version, maybe its in use?"
I tried restarting my activesync & rebooted the pc (winxp), The funny thing is when i try to flash with the NOID WM5 flash it works great.
I also flashed a G4 Prophet & it worked.
Before reflashing...
U need to downgrade to WM5 OEM with e.g : RUU_Prophet_220734_2207114_024721_NVID
(Look for on this board )
I had the same problem.
+
0pal said:
U need to downgrade to WM5 OEM with e.g : RUU_Prophet_220734_2207114_024721_NVID
(Look for on this board )
I had the same problem.
+
Click to expand...
Click to collapse
I did that already using the same file "sharebigfile.com_RUU_Prophet_220734_2207114_024721_NVID" & i understand that once i get to the boot screen, i need to flash to WM6 but it just doesnt work.
Any other suggestions ??
naser404 said:
I did that already using the same file "sharebigfile.com_RUU_Prophet_220734_2207114_024721_NVID" & i understand that once i get to the boot screen, i need to flash to WM6 but it just doesnt work.
Any other suggestions ??
Click to expand...
Click to collapse
1.When you get to the boot screen, let WM5 start, tap once and do a hard reset.
2.Load WM6.
I just tried that, still no go. ANy other suggestions ?
naser404 said:
Hi,
I have a G3 Prophet, I did flash it with WM6 before & it worked but now every time i try to flash with [pdaviet] 4.0.0.0.4s_pv or other WM6 roms i get the same freakin error " Could not update itsutils.dll to the current version, maybe its in use?"
I tried restarting my activesync & rebooted the pc (winxp), The funny thing is when i try to flash with the NOID WM5 flash it works great.
I also flashed a G4 Prophet & it worked.
Click to expand...
Click to collapse
If you followed exactly what others suggested, it should be okay. Read the Sticky notes on top of the forum and follow EXACTLY word by word.
If you think you have done so but still failed, there is another way to get around the "itsutils.dll in use" problem -- just copy the 2 .cabs (Cert_SPCS.cab and EnableRapi.cab) in the folder of the new ROM, into the PPC phone any directory and run them. then repeat the 2nd step. It will go away. But that is not a clean method.
Hope it helps. Good luck.
SeaPea said:
If you followed exactly what others suggested, it should be okay. Read the Sticky notes on top of the forum and follow EXACTLY word by word.
If you think you have done so but still failed, there is another way to get around the "itsutils.dll in use" problem -- just copy the 2 .cabs (Cert_SPCS.cab and EnableRapi.cab) in the folder of the new ROM, into the PPC phone any directory and run them. then repeat the 2nd step. It will go away. But that is not a clean method.
Hope it helps. Good luck.
Click to expand...
Click to collapse
and remember to use the correct G3 ROMUpdateUtility.exe file in the first step!
SeaPea said:
If you think you have done so but still failed, there is another way to get around the "itsutils.dll in use" problem -- just copy the 2 .cabs (Cert_SPCS.cab and EnableRapi.cab) in the folder of the new ROM, into the PPC phone any directory and run them. then repeat the 2nd step. It will go away. But that is not a clean method.
Hope it helps. Good luck.
Click to expand...
Click to collapse
Just wanted to thank you SeaPea, it "Finally" worked & i hope i can pay you back.
1 question though, what do you mean by not a clean method ?
Thanx again
hi naser404,
i also got same problem when upgrading wm6
1.Finished step1 (downgrade to wm5nvid)
2.Restart ppc, show welcome screen and .....
3.Windows will inform you to do setting (activesync)<---don't do this part
4.click cancel and windows will use "Guest" to link with ppc
5.run upgrade.bat
hope it can help you
P.S.my english is not good, just try to give you some advise
Hang83 said:
hi naser404,
i also got same problem when upgrading wm6
1.Finished step1 (downgrade to wm5nvid)
2.Restart ppc, show welcome screen and .....
3.Windows will inform you to do setting (activesync)<---don't do this part
4.click cancel and windows will use "Guest" to link with ppc
5.run upgrade.bat
hope it can help you
P.S.my english is not good, just try to give you some advise
Click to expand...
Click to collapse
Thanx a lot Hang83, I'll give that also a go & see how things work. I am greatfull to all you guys for the help.
Naser
Hi.
During upgrade to Crystal V3, I get this error at the end:
Please look at attached image...
Anyone knows what the fault is?
PS. This is the new Prophet that I got as a replacement for the old, bricked one...
Regards.
Try to move the install folder to C:/
I'm not sure if it is the same error message, but months ago I had the same prob and after this it worked.
Good luck
Tried, no luck...
hifiasylum said:
Tried, no luck...
Click to expand...
Click to collapse
reset phone and restart PC.. after that install aku 2.2 and retry..
Done, no luck...
Will try with another PC. Maybe this phone is locked?
Will go on a search in the forum later tonight.
Thanks for all help.
Will make it in the end!
Regards, Lars
hifiasylum said:
Done, no luck...
Will try with another PC. Maybe this phone is locked?
Will go on a search in the forum later tonight.
Thanks for all help.
Will make it in the end!
Regards, Lars
Click to expand...
Click to collapse
In the WM6 install folder ou will find 2 .cab files.
Bring them to the mobile and install them.
After that try again.
Should work.
Did you perform step1 before running Crystal upgrade?
I had the same problem... It worked successfully on a different computer.
panda88 said:
Did you perform step1 before running Crystal upgrade?
Click to expand...
Click to collapse
Yes, I allways downgrade before I upgrade.
Really, I do.
l3v5y said:
I had the same problem... It worked successfully on a different computer.
Click to expand...
Click to collapse
I have now tried 6 different computers, no luck. Believe that the fault is that I must unlock the phone or something. Donno, maybe the easiest thing is to sell the whole phone and get one a little more "programming friendly"?
dkleuven said:
In the WM6 install folder ou will find 2 .cab files.
Bring them to the mobile and install them.
After that try again.
Should work.
Click to expand...
Click to collapse
You dont think this will in some way or the other f_ _k up my Prophet?
hifiasylum said:
You dont think this will in some way or the other f_ _k up my Prophet?
Click to expand...
Click to collapse
It shouln't!
I saw from one of the thread, somebody also has the same exact problem, this is caused by the path is too long. It is suggested to put it in C:\, which you said you have done. The other person reported that it's working after he moved the installation file. I dun understand why it wouldn't work with yours.
Here is the post, finally found it:
http://forum.xda-developers.com/showthread.php?p=1549150#post1549150
User reported the problem was solved in #318
did u unlock CID yet?
Hi again. Found the problem. It seems that I was using a somewhat corrupt downloaded rom. The rom was ok, but it must have been destroyed during the downloadprocess.
Now the phone has Gullum Touch IX installed and works like a charm.
Thank for all your help, great forum!
Regards, Lars
818pro problem during upgrade to wm6
hai..
during upgrade my dopod 818pro to wm6, suddenly blackout and my upgrading was disrupted.. i reset back my dopod 818pro to continue back my upgrading..
but, I'm facing a problem which it's just hanging at start up screen..
i already try hard reset many time, but still can't to operate..
i just want to synchronize back to my pc to continue back my upgrading...
could somebody help me to this matter.. i don't know what to do now..
if it can enter bootloader, check the wiki for recovery, and follow it through.
Hello guys, i own a stock vodafone TP. I've tried several rom updates however all of them stuck at the beginning where it shows the % bar, it starts and stuck at 0 %.
the latest rom i've tried was "EnergyROM 2.0 40509" i did it through the "EnergyROM Upgrade.exe".
is there anything i'm missing here??
help me please..
if u can extract the *.nbh file (assuming it is inside the EnergyROM Upgrade.exe), then u can try flash using microSD. And u should post in EnergyROM thread.
krot84 said:
Hello guys, i own a stock vodafone TP. I've tried several rom updates however all of them stuck at the beginning where it shows the % bar, it starts and stuck at 0 %.
the latest rom i've tried was "EnergyROM 2.0 40509" i did it through the "EnergyROM Upgrade.exe".
is there anything i'm missing here??
help me please..
Click to expand...
Click to collapse
Hard SPL maybe
Shazad.K said:
Hard SPL maybe
Click to expand...
Click to collapse
Oh yeah, he said he did several rom updates but didnt mention custom or stock rom
monx® said:
Oh yeah, he said he did several rom updates but didnt mention custom or stock rom
Click to expand...
Click to collapse
indeed they were custom rom
ok i'll try the flash trough my SDHC. hopefully
krot84 said:
indeed they were custom rom
ok i'll try the flash trough my SDHC. hopefully
Click to expand...
Click to collapse
if i am reading your post correctly, you've never been able to flash a custom rom. If this is the case, have you "hard spl" your phone as yet?
Yes you're right. maybe i mixed up with the whole process of the hard spl even though i had read the guide several times .
First HSPL your phone...
Then Flash the ROM of your choice...
And READ, READ, READ, READ a lot, before...
thanks man!!! i'll try
pbmestre said:
First HSPL your phone...
Then Flash the ROM of your choice...
And READ, READ, READ, READ a lot, before...
Click to expand...
Click to collapse
So i have tried to Hspl my phone using http://forum.xda-developers.com/showthread.php?t=448008 guide, but no luck.
first i tried to run the RaphaelHardSPL-Unsigned_190_1_3.exe but it said that there was an error, then i used the SSPLManual.exe the phone turned black and an icon appeared on my pc's task bar saying there's a new "something" - (can't remember the actual name) found. And that was it.
what should i do next because i saw at the bootloader that the spl remained the same..
krot84 said:
So i have tried to Hspl my phone using http://forum.xda-developers.com/showthread.php?t=448008 guide, but no luck.
first i tried to run the RaphaelHardSPL-Unsigned_190_1_3.exe but it said that there was an error, then i used the SSPLManual.exe the phone turned black and an icon appeared on my pc's task bar saying there's a new "something" - (can't remember the actual name) found. And that was it.
what should i do next because i saw at the bootloader that the spl remained the same..
Click to expand...
Click to collapse
leave the phone plugged in when it says installing "something." even if it takes 5 minutes...let it sit until the computer installs the driver.
then run the spl again. this happens to me every now and then. just give it time to install the driver.
you ment to run the RaphaelHardSPL-Unsigned_190_1_3.exe from my computer ??
yes...
it needs to install the driver for flashing the device.. on the pc.. when it done the hardwarewizard tell you that it works.. after that start the hardspl prog
thanks, i'll give it a try later on this day 'cause i'm at work now
that would be the best option
i doubt ur systemcommander let you install anything like drivers and tools to withstand his authority lol
LOL i don't think anybody minds what i do on my computer here at work..
then whats the wait ? hehe
mmm the data cable i guess... don't have it here
lmao
oke oke u got me there
(they're like 3 bucks in most local stores (not that im an addict or anything (a)))
not at all )
by the way, i've tried yesterday to do exactly as you told but no luck.
after i used the SSPLManual and pressed the RaphaelHardSPL-Unsigned_190_1_3.exe it said " error - there's a problem operating or something like that"
hello together,
i have been reading a lot in this forum but i did not find a solution. This is my problem:
My HTC TD2 shows a pixel error, therefor i should sent it back to the provider. Because i have had ERG-ROM with hard-spl on the phone i have tried flashing first sspl. After that i have tried to flash the original HTC-ROM, but at 9% it fails.
After the recovery the device boots to this 9%-Screen and that´s all. If i am booting to the bootloader, the Bootloader-Modus (Tricolour-Screen) appears, but in the upper right corner stands:"ruunbh"
What can i do next?
schHTC said:
hello together,
i have been reading a lot in this forum but i did not find a solution. This is my problem:
My HTC TD2 shows a pixel error, therefor i should sent it back to the provider. Because i have had ERG-ROM with hard-spl on the phone i have tried flashing first sspl. After that i have tried to flash the original HTC-ROM, but at 9% it fails.
After the recovery the device boots to this 9%-Screen and that´s all. If i am booting to the bootloader, the Bootloader-Modus (Tricolour-Screen) appears, but in the upper right corner stands:"ruunbh"
What can i do next?
Click to expand...
Click to collapse
well, it has stock SPL now, yes? the custom OS is also erased by now... if not, then do a task 29 to make sure it is erased.
and then you can send the phone back no problem.
PS: I pressed thanks accidentally heh.
actually you should first flash the stock rom and then flash back the stock SPL (that's what i did, at least).
so, my advise would be to install the HARDSPL, then flash the stock rom and finally flash the stock SPL. this worked for me
good luck
cmonex said:
well, it has stock SPL now, yes? the custom OS is also erased by now... if not, then do a task 29 to make sure it is erased.
and then you can send the phone back no problem.
PS: I pressed thanks accidentally heh.
Click to expand...
Click to collapse
cmonex, do you think that a phone without any OS/ROM will not be suspicious?
tuniel said:
cmonex, do you think that a phone without any OS/ROM will not be suspicious?
Click to expand...
Click to collapse
afaik, as long as SPL is stock it should be okay... better than if it was booting to a cooked rom.
OP did have the original shipped ROM for the device, it seems. so he can say it got stuck when flashing, which is true.
cmonex said:
well, it has stock SPL now, yes? the custom OS is also erased by now... if not, then do a task 29 to make sure it is erased.
and then you can send the phone back no problem.
PS: I pressed thanks accidentally heh.
Click to expand...
Click to collapse
Can you explain to me please, I have this same problem, I tried the ROM update and it failed also to 9% and is now just the home screen, I need the steps to recover the phone, thanks.
oSanto- said:
Can you explain to me please, I have this same problem, I tried the ROM update and it failed also to 9% and is now just the home screen, I need the steps to recover the phone, thanks.
Click to expand...
Click to collapse
SPL version?
which ROM did you try?