Ok, I know there are a LOT of posts already. I have read through a lot of them but I'm struggling a little so I'd appreciate any help anyone is willing to give.
I have upgraded my SPV M1000 to WM5 1.60c WWE. I used Buzz's install, in case you were wondering.
At first I had an issue with Activesync but then I found that I needed Activesync 4 for it to work. I have now installed that and it has sync'd fine.
I'm having trouble with the camera and record buttons but from what I've seen on here most people are and (for me anyway) it's not the end of the world.
My questions are:
1. I previously had 2003se on my device. When I installed it (or whenever it hard reset) an auto-install kicked in and installed some very handy apps (including MMS which is missing) and basically everything was configured for me. I've noticed that this isn't on this particular update. PLEASE correct me if I'm wrong but is that called the extrom? If so, can I get one for WM5? (A link would be nice! :wink: )
2. As I mentioned above, the camera button doesn't work but the camera does. However I'm really not impressed by the camera app. Why does this version only use a window on the screen when the old one used the whole screen?!? I know it makes no difference to the quality of picture taken but I'd much rather have the full screen view finder. is there an alternative for this?
If anyone can advise on this I'd really appreciate it.
Now I'm off home to re-install my fave apps!
Right, I'm on the verge of downgrading back to 2003SE and restoring back to where I was.
Why?
Well, I must say I do like the interface. It's nice. The new screens in the phone app are nice, it all works nice.
Now the problems.
First, my 'must have' app doesn't work. SPB Pocket Plus. I can't remember the exact error message but it was something about the version. I'm using SPB Pocket plus 2 by the way.
Second, I tried installing Tomtom 5. Didn't work. It failed on the PC, after clicking next on the verification screen. I've read through some posts and found possible ways around but it looks like it could take a little while and, to be honest, if I'm going to have trouble with other apps too I'd rather just downgrade without spending hours trying pointlessly to get it working.
Obviously the side buttons don't work but like I said before, that's not too important to me.
Now that I've written this all down it just looks like little niggles and why am I moaning but I still feel inclined to downgrade all the same.
If anyone can help me out then I'd really appreciate it.
Don't worry about this. I've decided to downgrade until I can guatantee that everything will work properly.
Having read a lot of posts... both potentially apropos and perhaps diverse... from this August company of Ameo sages and mages, I have been moved to write to you to ask if there is something you can advise with respect to WM6 on our Ameo.
We have two such similar devices, both in T-Moble livery... with the nice leather book binding and the peculiarly useful pen pointer.
One arrived well-used with HTC Windoze mobile 2.21.405.2 on it, and the accompanying larger sized HTC home module, apparently of that period.
The other arrived practically new and boxed, with Windoze Mobile 2.35.110.4 on it, and the HTC Home characteristically implemented in the task bar area.
Being housebound disabled, the Tom Tom which came with it is virtually useles to me as well... so if anyone is desperately seeking one then we might arrange something.
The new unit came in and came up from cold. Not having a method whereby you can stop the branding process, as we do on our XDAIIs units, we were forced to permit that to continue... which was our first surprise. However that seems to bring in some benefits... in the shape of Opera and Tru-Flo... as well as a bit of T-Mobile dross too.
The HTC unit functions pretty well as far as I can see, and takes more or less everything you can give it to try. And it also starts on keyboard contact too.
The T-Mobile does not, and also needs to be re-set fairly often.
Too often for my money.
The HTC unit is unlocked as far as I know. The T-Mobile is awaiting a Pay-As-You-Go Card from me, and the use of the unlock code, which was obtained for us by the person who sold it to us.
The real tell for us (as mere users rather than mavens) was oddly enough, not with a performance tool kit or with any kind of enhancer, but with Hidden Expedition Titanic... of all things.
It works fine on HTC, but appears to glitch on the sound on the T-Mobile, and then hangs. Other similar softwares appear to do the same immediately after install, and then sometimes seem to operate as they should after a re-set. Astraware Solitaire WE and Robo, to name but two.
Going on from there, we got hold of Syberia. As big a test as you might want for this type of device I thought. That works pretty well again on the HTC, but inexplicably stalls on the T-Mobile far too frequently... necessitating a re-set. It is my impression that it does so if run from a previously closed session involving more or less any other task or purpose but can sometimes function adequately from a warm boot. (There are occasions with this unit when I'd like to implement the old MSDOS computer users saw... and give it a warm boot... AND also a HOT Wellie.)
Again, it is only my impression, but it seems that if I run Pocket Mechanic Ram Reclaimer on this unit, and then run Syberia, we seem to get a longer run without a freeze... sometimes to where I have to close in the normal course of events.
The same sort of thing... system hangs... happens now I have tried it... in Word. Especially when using Transcriber.
I have to say that I had perhaps unreasonably high hopes of that, having had a Toshiba Portege Tablet for a while now also, and having been quite surprised at how good the Tablet version of Windoze is at handwriting recognition on that. Most unlike Microshaft...
Then I thought that problems we had (and still do occasionally, albeit not requiring a re-set however) with the Tosh might be similar on the Ameo.
On the Tosh, as it arrived, we found the startup to be inundated with little Toshiba software modules... many of which were uneccessary. We improved boot times no end by taking a lot of them out... although live processing sometimes still has slow periods.
Notwithstanding however I tried to look at the Ameo in the same way.
In the startup there are around a half dozen files, aside from the obvious... Magic Button and X-Scalar that are there due to my efforts. And there seems to be little or no information as to what these are, or what they actually do... or more importantly... if they can be safely left out.
I've no doubt, from my reading here, that a simple answer from you all would be to install the unlocker and the forthcoming cooked ROM.
End of problem... perhaps.
However I tend to be a little more conservative (or timid perhaps?) with this concept... also noting those poor folks who have "bricked" their units too.
We have had excellent service from our XDAIIs units over the years, and they have been good companions when we needed them, as well as just phones. They are still operating with WM2002SE and still most software that I "find" seems to work on them... including the Ameo-Glitching Hidden Expedition Titanic I might add.
This week the chap next-door-but-one also got an Ameo... having seen ours and liked it.
His came out of the box with WM5 on it... possibly old stock?
However it set me thinking again and this has finally moved me to ask the assembled wise old Ameo-ers... if perhaps we would be as well reverting our new Ameo to WM5 too... for the time being at least... or if we might be better employed seeking something like the HTC version on our HTC unit?
Or perhaps some other solution presents itself to you from my description?
I'd like to get the new unit starting from keyboard connect also, if anyone has the fix.
The HTC unit came with a restore CD with WM5 on it... and not the HTC version which is presently installed on it's ROM. So I cannot just mirror it to the new unit.
There must be a concensus surely?
The units are manufactured similarly, by the same processes, and using basically the same internals.
We need a windoze version for these which settles down and does what it is supposed to with most of the software that is available.
At the present moment I have "ancient-egyptian" XDAIIs, which seriously outperform at least one new Ameo... in most respects... and that can't be right.
QF
Ameo
XDAIIs
HP Jornada 720
Atari Portfolio
Cliff Notes version? In 5 sentences or less, what are you asking?
Cliff Notes?? Who he??
I want the second to run as well as the first... and I'd like to know why it doesn't.
QF
techntrek said:
Cliff Notes version? In 5 sentences or less, what are you asking?
Click to expand...
Click to collapse
quinbus_flestrin said:
Cliff Notes?? Who he??
I want the second to run as well as the first... and I'd like to know why it doesn't.
QF
Click to expand...
Click to collapse
Hi
I feel you have lots of time to write on here. therefore you must have time to read about these threads before you try to mirror anything. If you do not understand fully you may brick your ameo.
To unlock the CID: http://forum.xda-developers.com/showthread.php?t=315831
Read the above thread fully
upgrade the radio: http://forum.xda-developers.com/showthread.php?t=372904&highlight=radio
Upgrade to AP3 DUAL Rom: http://forum.xda-developers.com/showthread.php?t=346221
Both of your devices need to be unlocked if you want to upgrade another rom other than original ones. If you do not understand clearly please do not do any changes and read everything about athena.
Good luck
Microshaft Windoze,that's great.
Hi.
The mic on my phone has stopped working so no one can here me now during a phone call. I've tried a factory reset and re-installing my current rom checkrom v6. Still the problem is there.
It seems to me to be a hardware problem. My niece dropped my phone onto a dinner plate and got tomato sauce on it. Not a lot but some of it got into the speaker and micro usb port. I cleaned it immediately but looks like it's caused some damage.
Can anyone offer me a solution to this problem.
I'm thinking I'll need to replace the mic on the phone. Can anyone link me to a guide on how to do this? I'll probably replace the usb port as I've had issues with that for ages now.
Thanks
If you are not a person who is able to fix phones and such then I'd advise you to simply send the phone back to your carrier and tell them to fix it. (if you've still got your warranty)
Unlucky :/ Maybe next time don't let your niece near the phone within a 5 mile radius?
Have a good day and good luck with the phone :]
beston94 said:
If you are not a person who is able to fix phones and such then I'd advise you to simply send the phone back to your carrier and tell them to fix it. (if you've still got your warranty)
Unlucky :/ Maybe next time don't let your niece near the phone within a 5 mile radius?
Have a good day and good luck with the phone :]
Click to expand...
Click to collapse
I'm on pay as you go and I bought the phone second hand about 7 month ago so sending it back not really an option.
Just to update, when I turn on the speaker function when in call the mic works fine.
johnbhoyc said:
Can anyone offer me a solution to this problem.
I'm thinking I'll need to replace the mic on the phone. Can anyone link me to a guide on how to do this? I'll probably replace the usb port as I've had issues with that for ages now.
Thanks
Click to expand...
Click to collapse
I believe the part for the USB port will have the lower mic attached anyways. I think you're looking for part number GH59-10949A. You can find service manuals for various Samsung phones on www.samfirmware.com. But you'll need to register on that site (it's free) to download them. Passwords on the archive files are "samfirmware.com".
johnbhoyc said:
I'm on pay as you go and I bought the phone second hand about 7 month ago so sending it back not really an option.
Just to update, when I turn on the speaker function when in call the mic works fine.
Click to expand...
Click to collapse
That's because the speakerphone function uses the top mic, not the bottom mic.
ctomgee said:
I believe the part for the USB port will have the lower mic attached anyways. I think you're looking for part number GH59-10949A. You can find service manuals for various Samsung phones on www.samfirmware.com. But you'll need to register on that site (it's free) to download them. Passwords on the archive files are "samfirmware.com".
That's because the speakerphone function uses the top mic, not the bottom mic.
Click to expand...
Click to collapse
Thanks for your reply Very helpfull.
Can anyone recommend somewhere to buy the usb port. Preferably UK based for speedy delivery.
Thanks
Got part delivered and fitted it today. Everything working fine now. USB problem I've
Got part delivered and fitted it today. Everything working fine now. USB problem I've been having for a while fixed as well.
Only problem I encountered was one of the screw heads was worn away. Had to drill it out but got their in the end.
Thanks for your help folks
johnbhoyc said:
Got part delivered and fitted it today. Everything working fine now. USB problem I've been having for a while fixed as well.
Only problem I encountered was one of the screw heads was worn away. Had to drill it out but got their in the end.
Thanks for your help folks
Click to expand...
Click to collapse
Glad you got it worked out.
If you're interested, to help with protecting my USB port, I ordered some of these. They come 3 covers per order.
(I am in no way affiliated with this company...)
I decided it was prudent after reading all the horror stories on the forums about USB ports failing/overvoltage warnings/computers not detecting/chargers not registering.
Hi, I have a couple of HD2's ready for use within the business I work for.
These HD2's were purchased as replacements for older HD2's that had been used and were getting tempramental and old.
I have recieved the new HD2's and heres my problem:
The touch screen seems to decide when, and IF it works. The first time I EVER got it out of the box, unwrapped it etc the touch didn't work.
After a couple of restarts the touch works, then after a bit it will then decide not to work.
This happens constantly, it will work, then wont work, then work, then wont work.
When it works it is fine, just like the HD2 should be, it just seems to be like a moody teenager who decides when and if it want's to work.
Any one know what could cause this? Why it is happening and why it works and then doesn't?
Thanks !
the touch has always been a weak point of this phone, and your issue doesn't sound all that uncommon.
if they still have older version, rom then you should certainly update that.
if there's any warranty you should definitely go that route immediately,, because you almost certainly aren't gonna fix it.
Hi mate
Yes I have updated the ROM's which went from 1.4 (ish) to the current ROM listed on the HTC website. That seemed to fix it, but then I realised the phone was in a good mood, and 10 minutes later it started its hissy fit again.
And about warranty I don't know as I didn't buy them, we may have to attempt to send them back but thats gonna take weeks, as it took weeks for them to arrive. And we need them out and about tbh.
Do you have any idea what the cause is?
Hardware/Software?
Thanks !
sorry no clue why, and I'd say it's most likely hardware,,, a failing digitizer by the sound.
Sounds like the common digitizer issue, just had same with my personal TMOUS HD2.
Our local supplier said he had units 100% new but old that had failed in the box, reckons digi ribbon bonding to digi is bad on both solder & socket types.
From 20+ HD2 handsets we have running in our company I would conclude similar myself.
My personal handset has had extremely light & sympathetic use & hardly minimal use of end key but it still failed.
Hardware durability of digi/micro USB port & mainboard thermal control/BGA solder quality is very poor to be polite ...
Hi, I have the Galaxy Note i717 and had to replace my charging port as it had stopped charging reliably. I bought one of the many on ebay for around 8 bucks. I proceeded to put it in when I received it but to my dismay I no longer could get service at all, just wifi. So just to verify it was nothing I broke I put the old pcb back in and service returned. At that time I believed it was just a defective unit, so second try at it same thing no service old one works fine. Is this a problem anyone has ran into before? Any help I would appreciate.
jpeeler said:
Hi, I have the Galaxy Note i717 and had to replace my charging port as it had stopped charging reliably. I bought one of the many on ebay for around 8 bucks. I proceeded to put it in when I received it but to my dismay I no longer could get service at all, just wifi. So just to verify it was nothing I broke I put the old pcb back in and service returned. At that time I believed it was just a defective unit, so second try at it same thing no service old one works fine. Is this a problem anyone has ran into before? Any help I would appreciate.
Click to expand...
Click to collapse
It is quite possible that either your new port is the wrong part, or is damaged.
The port wiring is different between models ...I.E. SGH-I717, N7000, and other note models.
Even the charge cables are different part numbers between models, but visually look identical.
It just sounds like the port wiring is different to me ..
I suggest getting the port directly from samsung...even though it will cost a bit more.
At least then you have a fall back if the port won't function.
Or perhaps have the port repaired by Samsung directly ....
I'm sorry I can't offer more help .g
gregsarg said:
It is quite possible that either your new port is the wrong part, or is damaged.
The port wiring is different between models ...I.E. SGH-I717, N7000, and other note models.
Even the charge cables are different part numbers between models, but visually look identical.
It just sounds like the port wiring is different to me ..
I suggest getting the port directly from samsung...even though it will cost a bit more.
At least then you have a fall back if the port won't function.
Or perhaps have the port repaired by Samsung directly ....
I'm sorry I can't offer more help .g
Click to expand...
Click to collapse
Well both pcb boards that they sent me have the same markings as the one I removed. They also say on them SGH_I717_SUB_REV1.0_1107
So I do believe it to be the correct part. Just to clarify the new boards do charge the phone just cellular service stops. Maybe by some crazy luck I got two faulty boards. I wasn't sure they were going to send me a replacement so I ordered from another company as well so I guess I will have to see if that one works,
Interesting ....
The part seems okay ...
And the odds of two bad ports in a row is remote at best ....
Some time ago I saw a thread about an extra wire that traveled down from the antenna to the charging port....
And users were reporting that this very small wire was being damaged or missed when the port was serviced.
I've never seen this wire or connection ......but I figured I'd bring it up ..
Try a general search on the topic ...and see if it yields a result.....
I just remember it being a big deal ....g
Just wanted to update the post in case this happens to anyone else. After getting the free replacement for the first part I believed to be defective I also ordered from another company as it took more than a month for my replacement, so I believed them to had stood me up. Well the one from the other company arrived today, and worked. Maybe the others were for different networks or something. I don't know if that is possible Rogers vs ATT frequencies and what not but it worked and all is well.
jpeeler said:
Just wanted to update the post in case this happens to anyone else. After getting the free replacement for the first part I believed to be defective I also ordered from another company as it took more than a month for my replacement, so I believed them to had stood me up. Well the one from the other company arrived today, and worked. Maybe the others were for different networks or something. I don't know if that is possible Rogers vs ATT frequencies and what not but it worked and all is well.
Click to expand...
Click to collapse
I am having issues as well...
My phone has a Rev1.0_1107 part, and I cannot charge unless I play with the cable, so i decided to replace this port.
1st was from China (ebay) and received no signal, only wifi. Rev1.0_1107
2nd was a replacement from the same company, same issue. Rev1.0_1107
3rd was from a place in CA (ebay) and is Rev2.0_1206 and same issues.
I can put my original part in there, and I get signal just fine... anybody have any ideas on this matter? It's frustrating to have to keep battery swapping and would like to get this fixed.
MisterLas said:
I am having issues as well...
My phone has a Rev1.0_1107 part, and I cannot charge unless I play with the cable, so i decided to replace this port.
1st was from China (ebay) and received no signal, only wifi. Rev1.0_1107
2nd was a replacement from the same company, same issue. Rev1.0_1107
3rd was from a place in CA (ebay) and is Rev2.0_1206 and same issues.
I can put my original part in there, and I get signal just fine... anybody have any ideas on this matter? It's frustrating to have to keep battery swapping and would like to get this fixed.
Click to expand...
Click to collapse
The one that finally worked for me was from ebay company (no.1-tech) also china but has been operating flawlessly for sometime now.
jpeeler said:
The one that finally worked for me was from ebay company (no.1-tech) also china but has been operating flawlessly for sometime now.
Click to expand...
Click to collapse
Noted... thanks. I have searched them out and they only appear to have the cable for the N7000. Can anyone else recommend a place to buy these from?
Just noticed that when it's near my window, I get 1 bar of service... So it's like my signal strength is uber weak. I have a microcell in my home, and it is functioning properly (other ATT phones are connecting just fine) and works again as soon I put the original cable back.
Hi,I have a samsung Note N7000.
I'm have a similar issue,start with high power charging issue every 5seconds.I bought a replacement from ebay company in New Jerse it fixed that problem.but it created a problem when I make a call the other end can not hear me.I email the company and they sent #2 replacement.after
the charging port board was installed now I dont have any signal for service.the pcb# N7000/i9220_sub_Rev1.0.
I'm going try different company.what should I be looking for?I'm wasting too much time on this.
johnson1828 said:
Hi,I have a samsung Note N7000.
I'm have a similar issue,start with high power charging issue every 5seconds.I bought a replacement from ebay company in New Jerse it fixed that problem.but it created a problem when I make a call the other end can not hear me.I email the company and they sent #2 replacement.after
the charging port board was installed now I dont have any signal for service.the pcb# N7000/i9220_sub_Rev1.0.
I'm going try different company.what should I be looking for?I'm wasting too much time on this.
Click to expand...
Click to collapse
Having exact the same problem.. just a moment ago I tried the third board and still hacing exact same problem, no signal or one bar only when I have one bar I can make a call but the other end can not hear me
gregsarg said:
Interesting ....
The part seems okay ...
And the odds of two bad ports in a row is remote at best ....
Some time ago I saw a thread about an extra wire that traveled down from the antenna to the charging port....
And users were reporting that this very small wire was being damaged or missed when the port was serviced.
I've never seen this wire or connection ......but I figured I'd bring it up ..
Try a general search on the topic ...and see if it yields a result.....
I just remember it being a big deal ....g
Click to expand...
Click to collapse
Sorry to bring up an old thread but I wanted to bring this to others attention. What Gregsarg said about a white wire running down from the antenna is correct, or at least it is on an i717. It runs down from the right hand side of the board, behind where the flex board connects and onto the little round connector on the flex board, it's probably that that's been missed off of some phones as would be noticed by only getting 1 bar of signal! I've also noticed that the UK version of the note only has 4 brass connectors on the flex board 2 for the antenna and 2 for the speaker whereas the i717 has 5, 3 for the antenna and 2 for the speaker. I'm not sure what the difference is between a white or black i717 to be honest, i'd have thought it would only be the outer casing that had changed, I can't see them changing parts too, that just sounds stupid!
Anyway, the reason I'm posting is not just because of the above, it's because i'm in the middle of fixing an i717 for someone and was searching to see if a N7000 part would fit and although it looks as though it would I'm not willing to test that theory! I will say though that the missing brass connector is also connected to brass connector 2 on the Ariel/speaker module but on the flex board that connector also has a resistor above it which would likely cause an issue!
The part that i'm ordering is from a company in the UK but is a Rev 2.0 board and not the rev 1.0 that is in it already so i'm hoping that's not an issue else i'm gonna have to buy from China which is cheaper but will likely take an age to get here and the customer wants it done ASAP so what they want they get! I will update this thread once i've fitted the part and got it running along with a link to where I got it from.
h4x0rm1k3 said:
Sorry to bring up an old thread but I wanted to bring this to others attention. What Gregsarg said about a white wire running down from the antenna is correct, or at least it is on an i717. It runs down from the right hand side of the board, behind where the flex board connects and onto the little round connector on the flex board, it's probably that that's been missed off of some phones as would be noticed by only getting 1 bar of signal! I've also noticed that the UK version of the note only has 4 brass connectors on the flex board 2 for the antenna and 2 for the speaker whereas the i717 has 5, 3 for the antenna and 2 for the speaker. I'm not sure what the difference is between a white or black i717 to be honest, i'd have thought it would only be the outer casing that had changed, I can't see them changing parts too, that just sounds stupid!
Anyway, the reason I'm posting is not just because of the above, it's because i'm in the middle of fixing an i717 for someone and was searching to see if a N7000 part would fit and although it looks as though it would I'm not willing to test that theory! I will say though that the missing brass connector is also connected to brass connector 2 on the Ariel/speaker module but on the flex board that connector also has a resistor above it which would likely cause an issue!
The part that i'm ordering is from a company in the UK but is a Rev 2.0 board and not the rev 1.0 that is in it already so i'm hoping that's not an issue else i'm gonna have to buy from China which is cheaper but will likely take an age to get here and the customer wants it done ASAP so what they want they get! I will update this thread once i've fitted the part and got it running along with a link to where I got it from.
Click to expand...
Click to collapse
When getting the part, Revision usually does matter. Also the serial number under the revision number (Usually starting with DRC or DRG) can also matter. Getting the identical one is usually the best bet (albeit not the easiest considering people on ebay use stock images and don't show you the ACTUAL part you're getting.)
KaboodleMoon said:
When getting the part, Revision usually does matter. Also the serial number under the revision number (Usually starting with DRC or DRG) can also matter. Getting the identical one is usually the best bet (albeit not the easiest considering people on ebay use stock images and don't show you the ACTUAL part you're getting.)
Click to expand...
Click to collapse
I got the new part this morning, it was a REV 2.0 board and after putting it all back together including the white/grey ariel wire I can report that it's working perfectly, as good a signal as it had before and is now charging properly. The link to the UK based seller is here for anyone interested that needs a replacement in the UK - http://www.ebay.co.uk/itm/300819833823?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649 The part is £19.99 with no P&P and arrived in 1 day. Just in case the link doesn't work then the name of the supplier is gravedigga1.
EDIT:- I heard back from my customer today who has reported having problems with wifi, signal and loudspeaker! Therefore the Rev 2.0 part won't act as a decent replacement for the Rev 1.0 unfortunately. I wasn't able to fully test as the customer didn't leave his sim card in and he uses 1 of those weird networks which I don't have a sim for. I have managed to source another UK supplier on ebay for an even cheaper price of £12 and they verified that it is a Rev 1.0 board they have in stock and have put 1 aside for me. Once I know that one works for definite i'll report back again just to update the thread but this time the customer is bringing the phone when the new part is here so it can be tested fully before it goes back to him!
I just find it strange that even though the Rev 2.0 is exactly the same in every way as the Rev 1.0 board that it has these issues although i've not heard of the loudspeaker problem before so I think there's a fault with it anyway.
Yeah these notes are getting really dodgy in their old age. We've decided to basically not fix abutting except the screens anymore because getting the right parts is a nightmare.
Sent from my DROID BIONIC using xda app-developers app
This may be a little off key here and if I'm in the wrong thread I apologize but...
I have the i717, bought the charging port off of eBay and replaced it. After plugging in the phone the touch keys at the bottom lit up like I was in business. After allowing the phone to "charge" for about 2 hours, the touch keys were the only thing to work and light up on the phone. I could press the lock key on the side and the touch keys would come off and on like it was on the lock screen but the screen was black. Has anyone encountered this before? If so, please help!
Thank you
Btw, it seemed like the phone was charged/charging bc those touch keys were on...
samsung sgh-i717 usb port
Well I have tried three different suppliers and I have not found a board that works correctly . Some boards that network strength is weak , some boards the microphone doesn't work , some boards that speaker won't play . I have reinstalled my original board back in my phone and every time it returns back to working properly. I just need the USB /charge port to work . Please if you have any ideas let me know ib6469 @ yahoo . com . Thank you very much for or help
Pease Help..i717..charge port
Hello ,
My name is Russ and I have a Samsung Galaxy Note SGH-i717 ( AT&T ) which I love . About two months ago the charge port quit working , so I ordered one from Ebay ( Flex cable , Mic/USB board ) , installed it and my signal was weak after installing it so I reinstalled the original board and it went back to full power . I thought it was a bad board , so they sent me another , I installed board #2 and the speaker on the back had no sound , put my board back in and the speaker went back working . So I had the supplier send me another board #3 . I got it installed , and the Mic wouldn't pick up , I put my board back in everything goes back to normal . So I thought it might be the supplier , so I tried a different supplier , same thing . In total I have tried three different suppliers and I lost count on how many boards I have installed .. Every time I can reinstall the original board and it will stop whatever it's doing wrong . My board Number is SGH_I717_SUB_REV1.0_1107 , DRBL12IN BF , 69 . I am at a lost , I don't know if there's something I'm doing wrong . Thank You for your time ib6469 ( Russ )
same issu
Please let me know if anyone has had any luck finding a board that works... i am in the exact same boat... email me at bnanda0827 at yahoo.com
ib6469 said:
Well I have tried three different suppliers and I have not found a board that works correctly . Some boards that network strength is weak , some boards the microphone doesn't work , some boards that speaker won't play . I have reinstalled my original board back in my phone and every time it returns back to working properly. I just need the USB /charge port to work . Please if you have any ideas let me know ib6469 @ yahoo . com . Thank you very much for or help
Click to expand...
Click to collapse
note charching port
hi
i purchase this part from 6 different company but same problem no signal charging port works ok.
any boby have solution please let me know.its very annoing.
joe
zia_uddin said:
hi
i purchase this part from 6 different company but same problem no signal charging port works ok.
any boby have solution please let me know.its very annoing.
joe
Click to expand...
Click to collapse
So it looks like basically fixing the charge port on a galaxy note just isn't going to hapen if you want service. Nobody has found a solution?