Related
Hey i'm new to here....but i will get straight to the problem..
i been having problems with my mic, the one in the top. I thought it was a software issue but it was not because i tried flashing lots of stock roms but still didn't work...my other mike is working fine...but when i turn the speaker on the phone uses the mic in the top, and when video catting also the phone uses the top mic, so i cant do anything so my question is that is there any way to set my second mic to be used for everything...like for video chatting on skype and tango, instead of using the mic on top, can the mic in the bottom be used?? is it possible to set the lower mic to be used for everything?? hope someone will help me thank you!
please somebody help me please
I don't know the answer to your question, but dude, you gotta wait longer than a couple hours before whining.
This is a development forum, not a tech support forum. No one is paid to sit around watching for support request posts. People answer posts of their own free will, on their own time.
EDIT: actually, I'm curious now. You say you're having issue with your top mic. Do you have a case on the phone? If so, does the case have an opening for the top mic? If so, are you sure the mic opening is clear of debris?
i'm sorry.... no its doesn't have any case or anything...and its clear...i even tried to put a small pin into it to see if there is anything stuck inside it, but their was nothing
sugith said:
i'm sorry.... no its doesn't have any case or anything...and its clear...i even tried to put a small pin into it to see if there is anything stuck inside it, but their was nothing
Click to expand...
Click to collapse
Exactly what is the problem you are having with the upper mic anyways? You never say.
I don't know of any mods that will re-route all mic functions of the upper mic to the lower one... So if the upper mic is simply not functioning, it sounds like it could be hardware fault.
Your only option may be to send it for repair. Since you say you tried flashing a bunch of ROMs, you'll have to flash back to stock and reset your flash counter if you want any hope of warranty coverage. Otherwise you'll be paying for the repair job.
ctomgee said:
Exactly what is the problem you are having with the upper mic anyways? You never say.
I don't know of any mods that will re-route all mic functions of the upper mic to the lower one... So if the upper mic is simply not functioning, it sounds like it could be hardware fault.
Your only option may be to send it for repair. Since you say you tried flashing a bunch of ROMs, you'll have to flash back to stock and reset your flash counter if you want any hope of warranty coverage. Otherwise you'll be paying for the repair job.
Click to expand...
Click to collapse
the problem is that the sound is very low that i have to scream in it, even after that they could only hear a little sound
came across this long time ago... no idea if this still works.. but i heard its only temp fix
http://forum.xda-developers.com/showthread.php?t=1127103
warrez said:
came across this long time ago... no idea if this still works.. but i heard its only temp fix
http://forum.xda-developers.com/showthread.php?t=1127103
Click to expand...
Click to collapse
May or may not work, and will only work until a reboot, at which point he'd have to do it again.
If he has warranty, he should send it in. Otherwise, he could crack the case open and inspect the top mic to see if the rubber housing is seated properly. It might be partially blocking the mic.
thanks for trying to help guyss....i did try that before but it didnt help at all
sugith said:
thanks for trying to help guyss....i did try that before but it didnt help at all
Click to expand...
Click to collapse
So send it in for repair (hopefully warranty covered), or try to do phone surgery yourself. Those are really your only options.
I have exactly the same issue. Top mic is not working and even replacement of the board with mic, vibro-motor and mini-jack did't helped. I've realised that the problem is with a condensator or a chip on the main board. I also would like to find the modification wich can change top mic to the lower one. Please, if anyone knows how to do it, let me know.
Hello,
I have a major problem with my lower microphone (on the USB flex board), the microphone does not register much sound at all (very faint sounds are possible if you scream as loud as possible into the microphone directly).
I have replaced the USB flex board (properly, everything is connected correctly and the USB port works perfectly), but the microphone is exactly the same...
Anyone have any ideas? It seems a couple of people have similar issues, has anyone found a fix yet?
Also, does anyone perhaps have any ideas about how to force the top microphone (speaker phone mic) to engage as the active microphone during regular voice calls? I am 100% sick of using speaker phone for every voice call, especially considering I need to make private/confidential calls for work :\
and yes, I have removed the rubber housing as well and tested it without it, it makes zero difference.
Youve tried to repair it on rhe cheap and failed.Maybe take it to a repair shop and get it done properly.
And from your other thread,the spare one I have here has part no gt-i9100 rev2.2(so maybe the one you bought is still faulty )
Sent from my GT-I9100
So you've followed me to my thread because I made a post you didn't like in another thread, and offered complete shinfo.
Please, do not post again.
I am a fourth year EE student, I know how to replace a minor circuit board correctly.
Anyone who has any real advice, specifically about whether or not this may be some form of software issue, and with regards to my question about using the other microphone in voice calls, please let me know.
My mistake-I thought I was replying to a poster named Bodurr as he made a couple of threads about mic problems aswell.
He replaced the board and its still not working.
And I see what you mean about the other thread-I can assure you I never twigged it was you.
Anyway,if you require help,its advised to state what rom etc your running.That way someone could say "if your rooted make a nandroid backup then flash stock rom and see if problem persist".
Sent from my GT-I9100
I'm using rootbox ICS rom version 1.7, android 4.0.4 with siyah kernel v3.4.
Have made a nandroid backup and reflashed to stock a couple of times (including stock kernel and then CF root kernel) and nothing makes any difference.
The issue started whilst on gingerbread and has now carried on to ICS...
I'm seriously completely stumped and have no idea what is causing it :\
I've had a quick look and its advised to test using voice recorder to eliminate a hardware issue.
Other thing mentioned was to change audio values(but maybe need to be on GB to access and change values in the *#197328640# menu.
I don't know if you've done this already.
Sent from my GT-I9100
Just tested again with voice recorder (first time I have done this since swapping the USB flex board) and it's exactly the same issue.
There is SOME sound, but you need to have the volume on full with your ear right against the speaker to hear it, and it's still very faint like that.
What a bizarre issue, it seems no-one knows how to fix it either :\
GT-i9100 mic flex problem
lolthrash said:
Just tested again with voice recorder (first time I have done this since swapping the USB flex board) and it's exactly the same issue.
There is SOME sound, but you need to have the volume on full with your ear right against the speaker to hear it, and it's still very faint like that.
What a bizarre issue, it seems no-one knows how to fix it either :\
Click to expand...
Click to collapse
Did you ever find a solution to this? I too had usb/battery problems so changed my flex to very simalar rev2.2 but only to have the same mic problems
BigSilver said:
Did you ever find a solution to this? I too had usb/battery problems so changed my flex to very simalar rev2.2 but only to have the same mic problems
Click to expand...
Click to collapse
experiencing exactly the same issue, replaced the USB flex and now have no microphone pickup on voice calls / voice recorder apps.
using ICS so not got the service mode audio options available (says BLOCKED)
don't know where I've gone wrong? maybe the part wasn't exactly right? I got it from here > http://pages.ebay.com/link/?nav=item.view&id=251069751004
Heres someone that lists a seller and he says he has no problems.
Same here
lolthrash said:
Hello,
I have a major problem with my lower microphone (on the USB flex board), the microphone does not register much sound at all (very faint sounds are possible if you scream as loud as possible into the microphone directly).
I have replaced the USB flex board (properly, everything is connected correctly and the USB port works perfectly), but the microphone is exactly the same...
Anyone have any ideas? It seems a couple of people have similar issues, has anyone found a fix yet?
Also, does anyone perhaps have any ideas about how to force the top microphone (speaker phone mic) to engage as the active microphone during regular voice calls? I am 100% sick of using speaker phone for every voice call, especially considering I need to make private/confidential calls for work :\
Click to expand...
Click to collapse
Up here, anyone found solution for this issue? I'm experimenting now the same problem with microphone after replacing the USB flex board...
Thanks
Yeah, got the solution. It's actually the board/flex cable itself. Took me three boards to find that out. There is a lot of b-ware boards on eBay that were actually thrown out by Samsung because they did not pass QC. Just get a genuine spare part and your mic will be fine.
Gesendet von meinem GT-I9100 mit Tapatalk 2
confusy said:
Yeah, got the solution. It's actually the board/flex cable itself. Took me three boards to find that out. There is a lot of b-ware boards on eBay that were actually thrown out by Samsung because they did not pass QC. Just get a genuine spare part and your mic will be fine.
Gesendet von meinem GT-I9100 mit Tapatalk 2
Click to expand...
Click to collapse
damn, i got the same then... its gonna be hard to get a proper board... I was thinking maybe, it had some kind of security by solder like lasers...
There's a little difference between 2.2 and 2.3, a single resistor, could it be?
Also, can't connect USB in Mass storage...
confusy said:
Yeah, got the solution. It's actually the board/flex cable itself. Took me three boards to find that out. There is a lot of b-ware boards on eBay that were actually thrown out by Samsung because they did not pass QC. Just get a genuine spare part and your mic will be fine.
Gesendet von meinem GT-I9100 mit Tapatalk 2
Click to expand...
Click to collapse
Did you get the Rev 2.2 or 2.3?
RoRo1990 said:
Did you get the Rev 2.2 or 2.3?
Click to expand...
Click to collapse
R2.3
Tapatalked from my SGS2!
confusy said:
R2.3
Tapatalked from my SGS2!
Click to expand...
Click to collapse
Hmm some people are saying 2.3 won't be compatible. Was your phone originally 2.2 or 2.3? Also how do I tell if it is genuine? If it says oem?
Why wouldn't it be compatible. A higher revision number usually suggests that something has been improved. BTW I initially had a 2.2 sub circuit board, now it's 2.3.
Well the new board should look like the old one. I think I took a picture the day I switched my board out. I'll try too find it later.
Tapatalked from my SGS2!
confusy said:
Why wouldn't it be compatible. A higher revision number usually suggests that something has been improved. BTW I initially had a 2.2 sub circuit board, now it's 2.3.
Well the new board should look like the old one. I think I took a picture the day I switched my board out. I'll try too find it later.
Tapatalked from my SGS2!
Click to expand...
Click to collapse
I'm looking at two 2.3 models. One seems teal colored the other is a dark blue. Which one is the oem? Actually which color is yours?
RoRo1990 said:
I'm looking at two 2.3 models. One seems teal colored the other is a dark blue. Which one is the oem? Actually which color is yours?
Click to expand...
Click to collapse
The second one looks just like mine. But the OEM part actually comes with a grey mic enclosure. Make sure your part comes with it.
Tapatalked from my SGS2!
Hi, I have the Galaxy Note i717 and had to replace my charging port as it had stopped charging reliably. I bought one of the many on ebay for around 8 bucks. I proceeded to put it in when I received it but to my dismay I no longer could get service at all, just wifi. So just to verify it was nothing I broke I put the old pcb back in and service returned. At that time I believed it was just a defective unit, so second try at it same thing no service old one works fine. Is this a problem anyone has ran into before? Any help I would appreciate.
jpeeler said:
Hi, I have the Galaxy Note i717 and had to replace my charging port as it had stopped charging reliably. I bought one of the many on ebay for around 8 bucks. I proceeded to put it in when I received it but to my dismay I no longer could get service at all, just wifi. So just to verify it was nothing I broke I put the old pcb back in and service returned. At that time I believed it was just a defective unit, so second try at it same thing no service old one works fine. Is this a problem anyone has ran into before? Any help I would appreciate.
Click to expand...
Click to collapse
It is quite possible that either your new port is the wrong part, or is damaged.
The port wiring is different between models ...I.E. SGH-I717, N7000, and other note models.
Even the charge cables are different part numbers between models, but visually look identical.
It just sounds like the port wiring is different to me ..
I suggest getting the port directly from samsung...even though it will cost a bit more.
At least then you have a fall back if the port won't function.
Or perhaps have the port repaired by Samsung directly ....
I'm sorry I can't offer more help .g
gregsarg said:
It is quite possible that either your new port is the wrong part, or is damaged.
The port wiring is different between models ...I.E. SGH-I717, N7000, and other note models.
Even the charge cables are different part numbers between models, but visually look identical.
It just sounds like the port wiring is different to me ..
I suggest getting the port directly from samsung...even though it will cost a bit more.
At least then you have a fall back if the port won't function.
Or perhaps have the port repaired by Samsung directly ....
I'm sorry I can't offer more help .g
Click to expand...
Click to collapse
Well both pcb boards that they sent me have the same markings as the one I removed. They also say on them SGH_I717_SUB_REV1.0_1107
So I do believe it to be the correct part. Just to clarify the new boards do charge the phone just cellular service stops. Maybe by some crazy luck I got two faulty boards. I wasn't sure they were going to send me a replacement so I ordered from another company as well so I guess I will have to see if that one works,
Interesting ....
The part seems okay ...
And the odds of two bad ports in a row is remote at best ....
Some time ago I saw a thread about an extra wire that traveled down from the antenna to the charging port....
And users were reporting that this very small wire was being damaged or missed when the port was serviced.
I've never seen this wire or connection ......but I figured I'd bring it up ..
Try a general search on the topic ...and see if it yields a result.....
I just remember it being a big deal ....g
Just wanted to update the post in case this happens to anyone else. After getting the free replacement for the first part I believed to be defective I also ordered from another company as it took more than a month for my replacement, so I believed them to had stood me up. Well the one from the other company arrived today, and worked. Maybe the others were for different networks or something. I don't know if that is possible Rogers vs ATT frequencies and what not but it worked and all is well.
jpeeler said:
Just wanted to update the post in case this happens to anyone else. After getting the free replacement for the first part I believed to be defective I also ordered from another company as it took more than a month for my replacement, so I believed them to had stood me up. Well the one from the other company arrived today, and worked. Maybe the others were for different networks or something. I don't know if that is possible Rogers vs ATT frequencies and what not but it worked and all is well.
Click to expand...
Click to collapse
I am having issues as well...
My phone has a Rev1.0_1107 part, and I cannot charge unless I play with the cable, so i decided to replace this port.
1st was from China (ebay) and received no signal, only wifi. Rev1.0_1107
2nd was a replacement from the same company, same issue. Rev1.0_1107
3rd was from a place in CA (ebay) and is Rev2.0_1206 and same issues.
I can put my original part in there, and I get signal just fine... anybody have any ideas on this matter? It's frustrating to have to keep battery swapping and would like to get this fixed.
MisterLas said:
I am having issues as well...
My phone has a Rev1.0_1107 part, and I cannot charge unless I play with the cable, so i decided to replace this port.
1st was from China (ebay) and received no signal, only wifi. Rev1.0_1107
2nd was a replacement from the same company, same issue. Rev1.0_1107
3rd was from a place in CA (ebay) and is Rev2.0_1206 and same issues.
I can put my original part in there, and I get signal just fine... anybody have any ideas on this matter? It's frustrating to have to keep battery swapping and would like to get this fixed.
Click to expand...
Click to collapse
The one that finally worked for me was from ebay company (no.1-tech) also china but has been operating flawlessly for sometime now.
jpeeler said:
The one that finally worked for me was from ebay company (no.1-tech) also china but has been operating flawlessly for sometime now.
Click to expand...
Click to collapse
Noted... thanks. I have searched them out and they only appear to have the cable for the N7000. Can anyone else recommend a place to buy these from?
Just noticed that when it's near my window, I get 1 bar of service... So it's like my signal strength is uber weak. I have a microcell in my home, and it is functioning properly (other ATT phones are connecting just fine) and works again as soon I put the original cable back.
Hi,I have a samsung Note N7000.
I'm have a similar issue,start with high power charging issue every 5seconds.I bought a replacement from ebay company in New Jerse it fixed that problem.but it created a problem when I make a call the other end can not hear me.I email the company and they sent #2 replacement.after
the charging port board was installed now I dont have any signal for service.the pcb# N7000/i9220_sub_Rev1.0.
I'm going try different company.what should I be looking for?I'm wasting too much time on this.
johnson1828 said:
Hi,I have a samsung Note N7000.
I'm have a similar issue,start with high power charging issue every 5seconds.I bought a replacement from ebay company in New Jerse it fixed that problem.but it created a problem when I make a call the other end can not hear me.I email the company and they sent #2 replacement.after
the charging port board was installed now I dont have any signal for service.the pcb# N7000/i9220_sub_Rev1.0.
I'm going try different company.what should I be looking for?I'm wasting too much time on this.
Click to expand...
Click to collapse
Having exact the same problem.. just a moment ago I tried the third board and still hacing exact same problem, no signal or one bar only when I have one bar I can make a call but the other end can not hear me
gregsarg said:
Interesting ....
The part seems okay ...
And the odds of two bad ports in a row is remote at best ....
Some time ago I saw a thread about an extra wire that traveled down from the antenna to the charging port....
And users were reporting that this very small wire was being damaged or missed when the port was serviced.
I've never seen this wire or connection ......but I figured I'd bring it up ..
Try a general search on the topic ...and see if it yields a result.....
I just remember it being a big deal ....g
Click to expand...
Click to collapse
Sorry to bring up an old thread but I wanted to bring this to others attention. What Gregsarg said about a white wire running down from the antenna is correct, or at least it is on an i717. It runs down from the right hand side of the board, behind where the flex board connects and onto the little round connector on the flex board, it's probably that that's been missed off of some phones as would be noticed by only getting 1 bar of signal! I've also noticed that the UK version of the note only has 4 brass connectors on the flex board 2 for the antenna and 2 for the speaker whereas the i717 has 5, 3 for the antenna and 2 for the speaker. I'm not sure what the difference is between a white or black i717 to be honest, i'd have thought it would only be the outer casing that had changed, I can't see them changing parts too, that just sounds stupid!
Anyway, the reason I'm posting is not just because of the above, it's because i'm in the middle of fixing an i717 for someone and was searching to see if a N7000 part would fit and although it looks as though it would I'm not willing to test that theory! I will say though that the missing brass connector is also connected to brass connector 2 on the Ariel/speaker module but on the flex board that connector also has a resistor above it which would likely cause an issue!
The part that i'm ordering is from a company in the UK but is a Rev 2.0 board and not the rev 1.0 that is in it already so i'm hoping that's not an issue else i'm gonna have to buy from China which is cheaper but will likely take an age to get here and the customer wants it done ASAP so what they want they get! I will update this thread once i've fitted the part and got it running along with a link to where I got it from.
h4x0rm1k3 said:
Sorry to bring up an old thread but I wanted to bring this to others attention. What Gregsarg said about a white wire running down from the antenna is correct, or at least it is on an i717. It runs down from the right hand side of the board, behind where the flex board connects and onto the little round connector on the flex board, it's probably that that's been missed off of some phones as would be noticed by only getting 1 bar of signal! I've also noticed that the UK version of the note only has 4 brass connectors on the flex board 2 for the antenna and 2 for the speaker whereas the i717 has 5, 3 for the antenna and 2 for the speaker. I'm not sure what the difference is between a white or black i717 to be honest, i'd have thought it would only be the outer casing that had changed, I can't see them changing parts too, that just sounds stupid!
Anyway, the reason I'm posting is not just because of the above, it's because i'm in the middle of fixing an i717 for someone and was searching to see if a N7000 part would fit and although it looks as though it would I'm not willing to test that theory! I will say though that the missing brass connector is also connected to brass connector 2 on the Ariel/speaker module but on the flex board that connector also has a resistor above it which would likely cause an issue!
The part that i'm ordering is from a company in the UK but is a Rev 2.0 board and not the rev 1.0 that is in it already so i'm hoping that's not an issue else i'm gonna have to buy from China which is cheaper but will likely take an age to get here and the customer wants it done ASAP so what they want they get! I will update this thread once i've fitted the part and got it running along with a link to where I got it from.
Click to expand...
Click to collapse
When getting the part, Revision usually does matter. Also the serial number under the revision number (Usually starting with DRC or DRG) can also matter. Getting the identical one is usually the best bet (albeit not the easiest considering people on ebay use stock images and don't show you the ACTUAL part you're getting.)
KaboodleMoon said:
When getting the part, Revision usually does matter. Also the serial number under the revision number (Usually starting with DRC or DRG) can also matter. Getting the identical one is usually the best bet (albeit not the easiest considering people on ebay use stock images and don't show you the ACTUAL part you're getting.)
Click to expand...
Click to collapse
I got the new part this morning, it was a REV 2.0 board and after putting it all back together including the white/grey ariel wire I can report that it's working perfectly, as good a signal as it had before and is now charging properly. The link to the UK based seller is here for anyone interested that needs a replacement in the UK - http://www.ebay.co.uk/itm/300819833823?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649 The part is £19.99 with no P&P and arrived in 1 day. Just in case the link doesn't work then the name of the supplier is gravedigga1.
EDIT:- I heard back from my customer today who has reported having problems with wifi, signal and loudspeaker! Therefore the Rev 2.0 part won't act as a decent replacement for the Rev 1.0 unfortunately. I wasn't able to fully test as the customer didn't leave his sim card in and he uses 1 of those weird networks which I don't have a sim for. I have managed to source another UK supplier on ebay for an even cheaper price of £12 and they verified that it is a Rev 1.0 board they have in stock and have put 1 aside for me. Once I know that one works for definite i'll report back again just to update the thread but this time the customer is bringing the phone when the new part is here so it can be tested fully before it goes back to him!
I just find it strange that even though the Rev 2.0 is exactly the same in every way as the Rev 1.0 board that it has these issues although i've not heard of the loudspeaker problem before so I think there's a fault with it anyway.
Yeah these notes are getting really dodgy in their old age. We've decided to basically not fix abutting except the screens anymore because getting the right parts is a nightmare.
Sent from my DROID BIONIC using xda app-developers app
This may be a little off key here and if I'm in the wrong thread I apologize but...
I have the i717, bought the charging port off of eBay and replaced it. After plugging in the phone the touch keys at the bottom lit up like I was in business. After allowing the phone to "charge" for about 2 hours, the touch keys were the only thing to work and light up on the phone. I could press the lock key on the side and the touch keys would come off and on like it was on the lock screen but the screen was black. Has anyone encountered this before? If so, please help!
Thank you
Btw, it seemed like the phone was charged/charging bc those touch keys were on...
samsung sgh-i717 usb port
Well I have tried three different suppliers and I have not found a board that works correctly . Some boards that network strength is weak , some boards the microphone doesn't work , some boards that speaker won't play . I have reinstalled my original board back in my phone and every time it returns back to working properly. I just need the USB /charge port to work . Please if you have any ideas let me know ib6469 @ yahoo . com . Thank you very much for or help
Pease Help..i717..charge port
Hello ,
My name is Russ and I have a Samsung Galaxy Note SGH-i717 ( AT&T ) which I love . About two months ago the charge port quit working , so I ordered one from Ebay ( Flex cable , Mic/USB board ) , installed it and my signal was weak after installing it so I reinstalled the original board and it went back to full power . I thought it was a bad board , so they sent me another , I installed board #2 and the speaker on the back had no sound , put my board back in and the speaker went back working . So I had the supplier send me another board #3 . I got it installed , and the Mic wouldn't pick up , I put my board back in everything goes back to normal . So I thought it might be the supplier , so I tried a different supplier , same thing . In total I have tried three different suppliers and I lost count on how many boards I have installed .. Every time I can reinstall the original board and it will stop whatever it's doing wrong . My board Number is SGH_I717_SUB_REV1.0_1107 , DRBL12IN BF , 69 . I am at a lost , I don't know if there's something I'm doing wrong . Thank You for your time ib6469 ( Russ )
same issu
Please let me know if anyone has had any luck finding a board that works... i am in the exact same boat... email me at bnanda0827 at yahoo.com
ib6469 said:
Well I have tried three different suppliers and I have not found a board that works correctly . Some boards that network strength is weak , some boards the microphone doesn't work , some boards that speaker won't play . I have reinstalled my original board back in my phone and every time it returns back to working properly. I just need the USB /charge port to work . Please if you have any ideas let me know ib6469 @ yahoo . com . Thank you very much for or help
Click to expand...
Click to collapse
note charching port
hi
i purchase this part from 6 different company but same problem no signal charging port works ok.
any boby have solution please let me know.its very annoing.
joe
zia_uddin said:
hi
i purchase this part from 6 different company but same problem no signal charging port works ok.
any boby have solution please let me know.its very annoing.
joe
Click to expand...
Click to collapse
So it looks like basically fixing the charge port on a galaxy note just isn't going to hapen if you want service. Nobody has found a solution?
Hey guys,
I'm having a hardware issue with the mic. When I make calls people can't hear me. I had recently replaced the screen on my phone and think that the issue may be related to the disassembling of the phone. It is possible that the mic could have been damaged during that process or was damaged due to the fairly substantial fall the phone encountered when the screen got shattered.
So for those of you who have had any sort of experience with the internals of the device, could you let me know if the part I found is the correct one and should fix the issue with people not hearing me during calls? (By the way, they can hear me via speakerphone so I don't know if it makes a difference.)
Here's the link to the part: http://www.ebay.com/itm/Samsung-Gal...763348?pt=PDA_Accessories&hash=item4abbc3fc14
This part is located at the top of the phone where you plug in the headset. The phone may have another mic and that's where I need your expertise to verify wheTHER my searched item is the right part. Can anyone chime in, please? Thank you.
streak4m3 said:
Hey guys,
I'm having a hardware issue with the mic. When I make calls people can't hear me. I had recently replaced the screen on my phone and think that the issue may be related to the disassembling of the phone. It is possible that the mic could have been damaged during that process or was damaged due to the fairly substantial fall the phone encountered when the screen got shattered.
So for those of you who have had any sort of experience with the internals of the device, could you let me know if the part I found is the correct one and should fix the issue with people not hearing me during calls? (By the way, they can hear me via speakerphone so I don't know if it makes a difference.)
Here's the link to the part: http://www.ebay.com/itm/Samsung-Gal...763348?pt=PDA_Accessories&hash=item4abbc3fc14
This part is located at the top of the phone where you plug in the headset. The phone may have another mic and that's where I need your expertise to verify wheTHER my searched item is the right part. Can anyone chime in, please? Thank you.
Click to expand...
Click to collapse
Are you on stock? If not have you tried going to stock
Sent from my GS4 running CM11 Kandy Kane
I wasn't and I went to stock to no avail. I researched more and found the part for the lower mic located near the USB port and ordered it on eBay. Once received I will switch it out to see if it resolves the issue.
Sent from my Galaxy Nexus using Tapatalk 2
streak4m3 said:
I wasn't and I went to stock to no avail. I researched more and found the part for the lower mic located near the USB port and ordered it on eBay. Once received I will switch it out to see if it resolves the issue.
Sent from my Galaxy Nexus using Tapatalk 2
Click to expand...
Click to collapse
did swaping the part work for you becuase im have the same problem with my phone i flash all roms and still people cant hear me i can hear then fine.it only works with speaker phone and when i try talk to text it does not work
tlopez1973 said:
did swaping the part work for you becuase im have the same problem with my phone i flash all roms and still people cant hear me i can hear then fine.it only works with speaker phone and when i try talk to text it does not work
Click to expand...
Click to collapse
Flash rom only not a kernel
Sent from my GS4 running CM11 Kandy Kane
Sent from my SGH-I777 using Tapatalk 2
no I just flashed different Roms thinking that it was going to be a problem with the Rom but that really was not the problem with it. The problem is with the USB charger port there's a mic there that's went bad and the reason why people can't hear me when i make and receive call . I swap out my friend's old USB charger port that had a problem with the usb charger part but a good mic and I was able to make calls with no problem and hear people fine now here the part
hello to comunity,
i have the samsung galaxy s 2 gt-u9100 mobile phone and everything was perfect untill i opened the phone, the phone has problem at the back housing so i ordered a new one and replaced it, i made everything with caution and slowly. while i changed the back housing i opened the phone and everything was good untill i saw that there was no signal. i did it 2g and i see that there is onlu on raw ar the signal and sometimes none.
i opened the phone again and checked everything but saw nothing wrong. as i searched i saw that the GSM is this part and the cable that connects the antenna is this one . both of them are perfect.
i lost all my day trying with that , at start i had SlimRom 2 then i put the stock one via Odin but it didnt boot, stocked in the boot image (didnt wanted to search why ) so i flashed kernel again and then NeatRom, still no signal and then i went back to SlimRom. but the problem as i saw is not from the rom .
if anyone knows about that thing and tell me what to do i would be gladfull .
That bit is the antenna c/w speaker.There is a thread related to this about usb replacement.People mention about similar problems when they remove the antenna cable.
Heres a pic of spares I have,and look at the gold contacts on the antenna,as they need to be in good contact with the ones on the usb board.Maybe its that,or maybe new antenna is faulty.Try your old one in to eliminate that though.It could even be the antenna cable.
The thread is by someone whos name is Dugud,or similar
Edit:was close,this is it
http://forum.xda-developers.com/showthread.php?p=47066876
theunderling said:
That bit is the antenna c/w speaker.There is a thread related to this about usb replacement.People mention about similar problems when they remove the antenna cable.
Heres a pic of spares I have,and look at the gold contacts on the antenna,as they need to be in good contact with the ones on the usb board.Maybe its that,or maybe new antenna is faulty.Try your old one in to eliminate that though.It could even be the antenna cable.
The thread is by someone whos name is Dugud,or similar
Edit:was close,this is it
http://forum.xda-developers.com/showthread.php?p=47066876
Click to expand...
Click to collapse
thanks a lot for your reply my friend, my problem is not with the usb think i thing, it must be with the cable or i dunno. i had verry good signal and everything was working, now just the signal got verry low.
exept from buying repair part you say there is no fix right?
leonleonleon said:
thanks a lot for your reply my friend, my problem is not with the usb think i thing, it must be with the cable or i dunno. i had verry good signal and everything was working, now just the signal got verry low.
exept from buying repair part you say there is no fix right?
Click to expand...
Click to collapse
maybe take it to a shop with someone who knows what they are doing. I just had to do this with mine, I considered trying to get parts cheap and diy then I considered how much time and stress it could cause me = not worth it. It cost me £25 to have usb replaced, second thing I checked was the signal as I see many having problems with this - outcome is my phone is working sweet again and it only took a couple of hours of my time :cyclops:
Best of luck
Did you read that thread?.I seen a post on here once where someone said they removed that white antenna cable,then refitted it,and lost signal.Then they bought a new cable,which solved the problem.
Also, you dont know the condition of the part you changed,and theoretically you are meant to use anti static wristband and mat when your touching sensitive electronic components......lol
Sent from my SM-T210 using xda premium
theunderling said:
Did you read that thread?.I seen a post on here once where someone said they removed that white antenna cable,then refitted it,and lost signal.Then they bought a new cable,which solved the problem.
Also, you dont know the condition of the part you changed,and theoretically you are meant to use anti static wristband and mat when your touching sensitive electronic components......lol
Sent from my SM-T210 using xda premium
Click to expand...
Click to collapse
I finaly solved after 10 hours of trying. a did the patern that this guy did and it worked perfectly, but i still cant underestand what made this problem.
http://youtu.be/2Y6k5t1f7Qk