I went ahead and flashed my phone to dcd 3.1.6 but now epst will not open, is there any possiblity of me unscrewing this up without sending the phone back to the factory (my carrier does not have the ability to flash me back to orignal rom)? I tryed reflashing twice with diffrent options selected in the kitchen but, still nothing .
i will attempt to help you... this may or may not be the issue, but worth a shot
when you try to access the epst, i assume you are dialling ##778 ?
if you are using the dialer, it may try to autocomplete it and add a pound to the end. (##778# which will not work)
so... if you push up on the directional pad after tying in ##778 it will take focus off of the autocomplete and when you push send it should work.
this worked for me anyways when i had this issue.. i found this from a posting i think by serf from march.
let us know the results
taspankya said:
i will attempt to help you... this may or may not be the issue, but worth a shot
when you try to access the epst, i assume you are dialling ##778 ?
if you are using the dialer, it may try to autocomplete it and add a pound to the end. (##778# which will not work)
so... if you push up on the directional pad after tying in ##778 it will take focus off of the autocomplete and when you push send it should work.
this worked for me anyways when i had this issue.. i found this from a posting i think by serf from march.
let us know the results
Click to expand...
Click to collapse
If he's on Sprint, he wants to use ##778#.
Honestly my guess is that he didn't install the carrier cab or he has installed a third party dialer that has screwed his phone codes.
I had this exact issue...
It would start to open, then crash... even when going directly to epst in the windows dir.. it would immediately close.
Was just about to post about it, then I realized I had not installed the carrier cab. (I have Verizon). The Carrier Cab fixed it.
ok, to be specific with my issue (with verizon) was with the dialer packaged with dcd's rom, it was adding that extra an extra # sign, because for what ever reason i tried ##778# before i typed ##778, thus it always tried to autocomplete it when i pushed send.
all's well that ends well
i have dcd 3.2.0 and installed the cricket cab (it was the closest to my real carrier, xml file wise) still no epst any other suggestions?
well, google for a list of codes for your specific carrier. im sure they will list an epst code or at least you can try to adjust their format to the 778 number..
Did you try to open EPST manually by running \Windows\EPST.exe?
If that doesn't work, copy \Windows\EPST.lnk to your computer, open notepad, and drag it into notepad. Let me know what it says.
Try running the shortcut (lnk) or the executable file in the Windows directory for EPST.
..occassionally it takes a couple of attempts to get the util running.
[edit]DAMN! GC beat me by 2 minutes!
Try running the shortcut (lnk) or the executable file in the Windows directory for EPST.
..occassionally it takes a couple of attempts to get the util running.
[edit]DAMN! GC beat me by 2 minutes!
Click to expand...
Click to collapse
Key, he's using the cricket carrier cab because he said that's what most "resembles" his carrier. EPST.lnk for cricket most likely won't work for his carrier, that's why I'm trying to get him to post the contents of the cricket EPST.lnk (I'm too lazy to go look).
bwash, epst does come up for a split second, then drops out, I've tryed both ways, ##778 and going into the wondows file.
24#"\Windows\EPST.exe" ##778
What model of the Titan are you using?
under device info the model number is TITA100, Pioneer lists it as HTC PPC 6800.
Try editing EPST.lnk to ##778# at the end instead of ##778. Then save it and open it. See if that works.
unfortunately, it still blinks.... any other suggestions?
edit, I did some looking on the xml file for the cricket cab, it dosn't look like it makes an epst.epst file like all the other carriers, I flashed with alltel and now epst works, however, the code is not all zeros or my msl unlock code.
Ok, so I went forum searching and after a million try, I finally found a post that tell you that when you put your hex esn into getspc it has to be in caps. I did flash sprints official ROM and changed all of the settings, I can get on evdo, and send and recive txt messages.
ok i'm having the same problem with my phone... i used the USCC cab and i still cant get EPST to work... it flashs and thats it... eather way i try thru windows or ##778 ... anyone have any ideas?
ok i'm having the same problem with my phone... i used the USCC cab and i still cant get EPST to work... it flashs and thats it... eather way i try thru windows or ##778 ... anyone have any ideas?
Click to expand...
Click to collapse
1. Did you use the kitchen or the pre-cooked exe?
2. I'm not sure what USCC uses for ## codes, but have you tried ##778# without pressing send on the dialer?
3. Have you tried reinstalling the USCC carrier cab? (It will tell you the old one can't be uninstalled, it's ok, just continue with the install.)
The cricket cab doesn't work properly. Tried it on several phones and EPST would load and then disappear. Using the Alltel cab fixes the problem.
donnieb said:
unfortunately, it still blinks.... any other suggestions?
edit, I did some looking on the xml file for the cricket cab, it dosn't look like it makes an epst.epst file like all the other carriers, I flashed with alltel and now epst works, however, the code is not all zeros or my msl unlock code.
Click to expand...
Click to collapse
I use Sprint, and same problem here on DCD3.2.3!
If I dial ##778 or manually launch epst from windows it just flashes and disappears. What to do?
Related
Carrier: Alltel
Started with WM5 ROM.
Flashed to DCD's 2.1 WM6 ROM last week, no issues noted.
Yesterday flashed to 2.2 WM6.1 ROM and now whenever I get a data session going in a strong EVDO area I get dropped down to 1x when the data session finishes connecting?
I've moved back to 2.1, used no2chems 6.1 ROM and back to DCD's 6.1 ROM. Same problem all around now.
Radio problem maybe? Or user? If radio, anyone get me a link to the original 1.4?
Thanks in advance if anyone has any tips, I've tried looking around but only find people with MMS or other issues.
---------------------
This solution apparently only works for Alltel customers, if anyone finds solutions for Sprint/Verizon/Telus I'll add the solution to this post.
ALLTEL:
1. Enter EPST (##778), Edit (password= 000000).
2. View Info (left soft key).
3. Choose the "Security" item.
4. In the "HDR AN AUTH Password(LONG)" field, click to highlight.
5. Menu (right soft key), Edit
6. In the "Value" field, enter your Hex ESN (make sure all characters are CAPITAL, lowercase will FAIL).
7. Ok. Menu. Ok to save, then reset.
--------------------------------------------
SPRINT:
MADMARTlGAN said:
Hey in case you guys are still having problems with this, I can tell you what worked for me with Sprint.
You'll need your unlock code, if you don't have it, you've gotta get it from either Sprint or from one of the tutorials i've seen floating around here and other forums.
1. Sync your titan to back up your data.
2. ##786# Choose edit, enter your unlock code, then choose menu>restore. This will reset everything to factory settings.
3. Reset
3. ##UNLOCKCODE# Again choose edit.
4. Both MDN and MSID should be your wireless number (this was confirmed by Sprint T2 tech support)
5. Reset
6. Call your voicemail to make sure your phone service is working.
7. Connect to the internet. It should trigger IOTA/Provisioning and then EVDO should be working.
8. Resync your **** and you're good to go.
Hope this helps, it worked for me.
Click to expand...
Click to collapse
I think with Alltel you get 1x when roaming. Do *228 option 3 < Thats to activate your phone if you haven't already
Then do *228 option 2 to update your roaming preferences which ridded me of roaming in coverage area!
Americanmetal said:
I think with Alltel you get 1x when roaming. Do *228 option 3 < Thats to activate your phone if you haven't already
Then do *228 option 2 to update your roaming preferences which ridded me of roaming in coverage area!
Click to expand...
Click to collapse
Thanks for the response, I've been through that already and same results...
I even went back to the stock Alltel ROM and Radio, same thing.
With PRL 30029 AND 40029...
Oh well, I'll figure something out as I love the speed of DCD's 2.2!!!!
jake1s said:
Yesterday flashed to 2.2 WM6.1 ROM and now whenever I get a data session going in a strong EVDO area I get dropped down to 1x when the data session finishes connecting?
Click to expand...
Click to collapse
Did you check Start->Settings->Personal->Phone->Services->Mode of Operation to make sure it wasn't set to 1X only? I think that was the default setting on my phone.
I had this same problem, and then I reflashed with the 3.16 sprint rom twice and it went away.
Appreciate the responses, but I don't have the "Mode of Operation" on my Alltel 6800. And I've reflashed all kinds of ROMs with no luck...
Thanks for the ideas though...
jake1s said:
Appreciate the responses, but I don't have the "Mode of Operation" on my Alltel 6800. And I've reflashed all kinds of ROMs with no luck...
Thanks for the ideas though...
Click to expand...
Click to collapse
With the newest Advanced Config app, you can unhide the "mode of operation" option in there. I got it from here somewhere, do a search. I doubt this is your issue. I had this problem yesterday with Sprint. I got data in 1xRTT, but not EVDO. I ended up calling Sprint and they had to deactivate and reactivate the internet services on my phone. Immediately it worked like a champ.
I had this problem also and was able to take care of it by going into EPST (##778) and going under the security settings and putting the ESN Hex Value of Your Phone under the HDR Password. Mine got lost whenever I upgraded the radio. This will allow you to lock back onto the EVDO network
corwinb said:
I had this problem also and was able to take care of it by going into EPST (##778) and going under the security settings and putting the ESN Hex Value of Your Phone under the HDR Password. Mine got lost whenever I upgraded the radio. This will allow you to lock back onto the EVDO network
Click to expand...
Click to collapse
THANK YOU! THANK YOU! THANK YOU!
That did the trick (after I did it a second time and made the letters capital) and now I'm cruising EVDO style!!
Thanks!!!!
Hi I have this same issue.
i typed ##778 send
and get the view, edit , and cancel options.
do i find the hdr password under the edit?
when i choose edit, i get a password prompt and i do not know the password.
i am on dcd rom 2.2.0
i edited mine, and it does get on ev instead of 1x so i was glad but when i opened ie i cant get a data connection up now at all???
corwinb said:
I had this problem also and was able to take care of it by going into EPST (##778) and going under the security settings and putting the ESN Hex Value of Your Phone under the HDR Password. Mine got lost whenever I upgraded the radio. This will allow you to lock back onto the EVDO network
Click to expand...
Click to collapse
I just checked and I have a bunch of garbled characters in this spot. Does anyone else see something like this?
What did you guys have in that slot before you added your esn hex number?
the password you need is unlock code you can only get from sprint.
i also had the weird characters, i edited these out with my esn hex as mentioned and now i cant get a data connection at all, i get an error that i cannot connect. Anyone with any idea on what i can do?
I thought of downgrading the radio and then installing this one again and starting from scratch any better ideas?
My HDR password is also extended ASCII characters, has been for every ROM version I have run, and I get EVDO and on the Internet as well. I thought that was a problem when I had no data connection from a previous ROM, but it wasn't.
What worked for me was to go all the way back to the official 2.17, then to the leaked 3.16, etc. I made sure everything was set up and working properly on each version before moving on to another ROM.
excess4 said:
the password you need is unlock code you can only get from sprint.
i also had the weird characters, i edited these out with my esn hex as mentioned and now i cant get a data connection at all, i get an error that i cannot connect. Anyone with any idea on what i can do?
I thought of downgrading the radio and then installing this one again and starting from scratch any better ideas?
Click to expand...
Click to collapse
not true there is a program to find out the msl code for your phone if i was on computer i would give u guys the link
aatreya said:
I just checked and I have a bunch of garbled characters in this spot. Does anyone else see something like this?
What did you guys have in that slot before you added your esn hex number?
Click to expand...
Click to collapse
Again, I'm on Alltel so maybe for some unknown reason there is more to it for you Sprint users.
But, my MDR Password field was goofy stuff, deleted it and put in my Hex ESN in ALL CAPITALs and I stay at EVDO when my data connection is made now.
Deleted MDR PASSWORD and put esn hex, internet not working
ok guys i messed up pretty badly and deleted the MDR password and put my esn hex instead and now i cant get on the net.
I have an HTC TITAN running DCD 2.2 and latest 3.27 radio
any suggestions on how to get the password back????
aatreya said:
I just checked and I have a bunch of garbled characters in this spot. Does anyone else see something like this?
What did you guys have in that slot before you added your esn hex number?
Click to expand...
Click to collapse
yes i also have a bunch of giberish in there. i am afraid to change it becuase there will be no way for me to put that giberish back in there with all those weird looking characters.
i found the edit password which was a bunch of 00000 as many as the field would take
and i understand some people now get ev but no data connection now. i am on verizon and i dont know if that will happen to me as well.
my connection now says ev and doesnt change back to 1x anymore so i am going to leave this as is for now and not change it.
also my a-key is blank if that makes a difference. phone works fine though.
whatbish said:
ok guys i messed up pretty badly and deleted the MDR password and put my esn hex instead and now i cant get on the net.
I have an HTC TITAN running DCD 2.2 and latest 3.27 radio
any suggestions on how to get the password back????
Click to expand...
Click to collapse
you mean hdr password right? I did not see an mdr password listed anywhere
I have Alltel and have been trying NexVision's ROM, the DCD and and and, pretty much everything I could find.
Running the 3.27.00 Radio ROM and tried a lot of ROMS of the WM 6.1 ones
I cant get any of them working right!!
I dont seem to get any success after flashing connecting to the Internet and also constantly have the roaming indicator on (that triangle on the top).
Also it changed my MSC/SPC or whatever you call it from 000000 to something else which makes it impossible for me to use the *228 to update roaming and PRL via their automated telephone thing.
Now my question is,
which is the best working ROM for the Titan on alltel? Especially how do I get the thing to connect to the Internet again???
how do I get the Titan connected to QPST in order for me to change the SPC back to 000000?????
I appreciate any help, this forum is so helpful and such great work you guys!!!!!
keep it up!!!!
jamesfelarca said:
I have Alltel and have been trying NexVision's ROM, the DCD and and and, pretty much everything I could find.
Running the 3.27.00 Radio ROM and tried a lot of ROMS of the WM 6.1 ones
I cant get any of them working right!!
I dont seem to get any success after flashing connecting to the Internet and also constantly have the roaming indicator on (that triangle on the top).
Also it changed my MSC/SPC or whatever you call it from 000000 to something else which makes it impossible for me to use the *228 to update roaming and PRL via their automated telephone thing.
Now my question is,
which is the best working ROM for the Titan on alltel? Especially how do I get the thing to connect to the Internet again???
how do I get the Titan connected to QPST in order for me to change the SPC back to 000000?????
I appreciate any help, this forum is so helpful and such great work you guys!!!!!
keep it up!!!!
Click to expand...
Click to collapse
It sounds like you let the Sprint customizations run. Sound about right?
Here's what I had to do after the Sprint customizations locked me out of the PST:
Geckotek said:
I flashed back to the stock VZW ROM (third time I think), I made sure all of my provisioning issues with Verizon were worked out (finally had the tech "kick the switch").
1) Then I proceeded to load the 2.4 bootloader,
2) then the 3.16 Unauthorized Sprint ROM w/ radio,
3) then finally installed a cooked DCD 2.3.2 ROM.
Things to note:
1) I never let the Sprint ROM boot up
2) I had no signal so ran *22802 then hit End as soon as it connected
3) Still no signal after reboot
4) No A key, MSID, or MDN issues, but I did re-enter the MSID and MDN as discussed in other threads
5) After re-entering MSID and MDN then after reboot I had signal
6) never had to run *228 to OTA program (in the past programming with *228 has reversed the effect of re-entering the MSID and MDN)
In general, I feel that the OTA from VZW sends down some programming that conflicts with the 3.27 radio...but I have nothing to prove that.
GPS is running great (I just loaded the AstroGPSLauncher)
Not sure about Rev A. It does seem snappy. What's a good site to test from the phone?
I'm happy and not re-flashing until a solid radio for Verizon arrives.
Click to expand...
Click to collapse
that all worked for you on Verozon, but I got alltel!!!
i still want to know how to change my MSC SPC, the Master Code back to 000000
and also what would you recommend is the best ROM that works for ALLTEL and also has the internet working.
I did all the MSID and MSN entering by hand.
I do get service for text messaging and Phone service as well.
i cannot get access to the internet, and also am constantly roaming. thats my issues
I have Alltel and DCD's 1.7.x ROMS are GREAT! No GPS but I don't need it.
you have a link to the ROMs??
jamesfelarca said:
you have a link to the ROMs??
Click to expand...
Click to collapse
I have Alltel PPC6800 and I am running Radio 3.27 and DCD2.3.2 just fine. Download the kitchen and run it. Alfter everything is installed then dial the *228 and pick option 3 for new phone. That will update all the settings you need.
Here is all the stuff you need. Pick which alltel rom you want. I know they all work good, some have more features.
http://forum.xda-developers.com/showthread.php?t=369920
jamesfelarca:To change the PRL you can put ##775 in the dial pad and send. Then enter the 000000 for the unlock code and select update PRL ->Menu->Edit and select the current PRL (probably a good idea to have this on your memory card) http://www.corolada.com/prl/ The one you want is 30031. Also you may want to do the ##778 unlock code 000000 and then check the NAM settings MDN and MSID should be your 10 digit number.
jamesfelarca said:
that all worked for you on Verozon, but I got alltel!!!
i still want to know how to change my MSC SPC, the Master Code back to 000000
and also what would you recommend is the best ROM that works for ALLTEL and also has the internet working.
I did all the MSID and MSN entering by hand.
I do get service for text messaging and Phone service as well.
i cannot get access to the internet, and also am constantly roaming. thats my issues
Click to expand...
Click to collapse
A) What my instructions help with is flashing a Sprint ROM to a non-Sprint phone
B) My instructions show you the only way I've ever seen how to remove the MSL from the phone.
So if you want your phone to work correctly, I suggest you give it a try. Your mistake was letting the Sprint customizations run....as far as I know, that is not easily reversible.
dwertz said:
I have Alltel PPC6800 and I am running Radio 3.27 and DCD2.3.2 just fine. Download the kitchen and run it. Alfter everything is installed then dial the *228 and pick option 3 for new phone. That will update all the settings you need.
Here is all the stuff you need. Pick which alltel rom you want. I know they all work good, some have more features.
http://forum.xda-developers.com/showthread.php?t=369920
Click to expand...
Click to collapse
Based on my experience, reflashing the ROM doesn't remove the MSL lock applied by the Sprint ROM. That's why I reverted to the stock bootloader and ROM/Radio.
dwertz said:
I have Alltel PPC6800 and I am running Radio 3.27 and DCD2.3.2 just fine.
Click to expand...
Click to collapse
Glad it works for you. I had problems with the radio. I was only receiving about 2/3 of sent SMS and OfficeSync did not update properly.
Here is a link to DCD's 1.7.0 here: http://forum.xda-developers.com/showthread.php?t=372853
I used the kitchen and it works very well for me.
i have alltel and update my ppc6800 fine all i had to do to remove the indicator icon was to do *228 option 3 wich is activate.
jamesfelarca said:
that all worked for you on Verozon, but I got alltel!!!
i still want to know how to change my MSC SPC, the Master Code back to 000000
and also what would you recommend is the best ROM that works for ALLTEL and also has the internet working.
I did all the MSID and MSN entering by hand.
I do get service for text messaging and Phone service as well.
i cannot get access to the internet, and also am constantly roaming. thats my issues
Click to expand...
Click to collapse
I'm not sure how to change the MCL back to 000000 but if you haven't already you should be able to use GetSPC to obtain the code for your device. Once you're in EPST check your Home SID to make sure this is correct. If not there's a good chance you'll be roaming all the time. Also make sure you have the newest PRL (*228 Option 2)
For your internet connection, check EPST Security and M.IP Default Profile and make sure your NAI and UserIDs are set to your phone number @alltel.net and your AAA shared secret and PPP Password should be "alltel" without the ". Your HDR AN AUTH Password should be your ESN (Hex).
I recommend dcd 2.32 also. It's what I'm using and it's working great.
Sounds like everyone else covered the how to's... but before you try anything else you might want to wait for DCD's new kitchen which will work with the official radio released for Sprint today.
Roaming Order
Does anyone know if there is a way to change the order of carriers my phone tries to roam to?
I have Alltel and apparently Sprint is at the top of there list. I live in an area where Sprint service sucks and there is no EVDO, but the Sprint tower is just close enough to be seen so I never get onto the Verizon Towers. I would like to set my Roaming order to be Verizon first then Sprint etc...
Thanks,
mr.ellsworth
I've since solved my boot screen issue. I've installed :
dcd 3.2.5
Titan_Radio_ROM_3.42.30
dcd USCC Carrier 20080801
I have no data connection, I deleted it says my username and password are incorrect. I've tried every combination of my 10digit number and uss.net that I can think of. I've also reinstalled the uscc carrier cab, did the *228 and a soft reset. I can connect for 2 kilobyts then after that I can't connect. I'm not finding much on these forums to help me out. Does anyone have any ideas?
additional info
Sorry, the phone is a USCC 6800
hey just to let you know I have the 6900 and I dial #777 not sure if u wanna try that
I've had the same problem everytime I change ROMS. I have Verizon and found after I've "activated" the phone using the *228 then option 1, I then do *228 and option 2 (update my roaming capabilitys). That has always enabled my data connection.
kmanuel74 said:
I've had the same problem everytime I change ROMS. I have Verizon and found after I've "activated" the phone using the *228 then option 1, I then do *228 and option 2 (update my roaming capabilitys). That has always enabled my data connection.
Click to expand...
Click to collapse
If that doesnt work and you have an old cell phone around you can swap the ESN's on VZW's web site under customer service. When you do this you reset all the security information for the handset. I find this way to be the quickest method that has never failed. I use it so much I have the other ESN almost memorized!~
Scott
k3an said:
I've since solved my boot screen issue. I've installed :
dcd 3.2.5
Titan_Radio_ROM_3.42.30
dcd USCC Carrier 20080801
I have no data connection, I deleted it says my username and password are incorrect. I've tried every combination of my 10digit number and uss.net that I can think of. I've also reinstalled the uscc carrier cab, did the *228 and a soft reset. I can connect for 2 kilobyts then after that I can't connect. I'm not finding much on these forums to help me out. Does anyone have any ideas?
Click to expand...
Click to collapse
Run EPST and make sure that your PPP user name and password in there are correct.
If you didn't back up your phone's programming with QPST before and after flashing there is a chance that your EPST information is corrupt which would cause data to not work.
You will need your SPC/MSL in order to access EPST. You can try 000000 if nothing else works, and if it is 000000, you will need to set it back to the correct SPC/MSL otherwise *228 won't properly update your phone. Also USCC doesn't offer an option 1 or 2 after dialing *228, they don't have an OTA reprogramming of their phone.
If those changes don't work, you can try posting your entire EPST on here (removing any personal info, i.e. phone #, ESN, etc) and one of us USCC folks can compare it to ours and let you know what other areas look corrupt.
This is the one downside to USCC customers, we have to take extra steps while programming our phones to get them up and running, luckily it's a one time thing, once the phone is flashed the first time, these settings stick.
BTC
Hey,
I'm not sure why this happen but for some reason, I can not access the "pst" thing by pressing "##778#" or "##778". I was able to do it before, but ever since I switch to a new Mogul it wont let me. I also tried "##775#" to edit the PRL, but it still wont let me. I saw the sprint rep did some other numbers, but I forgot what they used. I need to get on to check if my PRL is up to date and see if the "REV A" is activated; and plus I just want to get on it because I'm curious now. Does anyone knows what other codes I can used? Thanks in advance.
ps. I'm using DCD 3.2.6 Radio 3.42.50
dunno.
3.2.6/3.42.50 myself and ##778# brings up EPST just fine.
i came on to ask the same question. i cant seem to get any codes to work. using DCD 3.2.5 on sprint
Some dialers don't allow ##codes. Try a different dialer, either reflash from the kitchen and select a different dialer, or unselect both dialers and use the default. I can't remember which dialer it was that didn't work, but I'm 99% sure one of them didn't work.
BTC
This is for people who want Cricket to work perfectly, just follow these instructions not skipping a beat and you will be OK from then on! If you are not having problems obviously skip this!
I have updated this thread ONLY to Change a step. Its not a Required Change for current Cricket users however, it may be needed for Phones that have never been on Cricket before. I also re-phrased some things to be more understandable.
This thread is assuming that you already have your phone Unlocked (spc code all zeros) and that you have already contacted Cricket and had the Phone you are programming added to the Account. You might as well tell them you have a Motorola Razor V3C that will ensure there will be no problems obtaining EVDO.
Also ask Cricket for your MSID/MIN number (usually not your Phone Number) we will be needing the MSID/MIN if you dont know it, or if the phone was never on Cricket before.
My HTC Unlock Tools Directory, Read SPC Instructions Readme
My Cricket WAP and Arcsoft new versions or my Cricket Carrier CAB <--If you are installing one of my Cricket CABs dont test it until your PST settings are correct.
This thread is also assuming that you already have a CRICKET PRL file loaded in PST. If you have my ROM flashed than a couple PRL files that you can use are on device memory we will get to that later below.
Important note on PRL files. You must know what kind of Cricket Plan you have. If you have Roaming on your plan you need to use the 5 digit PRL files. If you DO NOT have Roaming on your plan you must use the PRL files that are considered 4 digits or contain a 0 at the beginning. Otherwise *228 will not work and you will not be able to Authenticate. Some report for users with roaming you may have to use PRL 1042 and set your SID to be able to *228. Examples below.
PRL 01013 = Non Roaming
PRL 38515 = Roaming
1. Now first thing you want to do is have a good Cricket CAB or ROM installed. This way when the PST settings are done they can be looked over again, and tested.
2. Now if you are starting from a fresh flash OK, if you are starting from a hard reset OK, we can continue. If you have a ROM installed that is having problems I recommend a hard reset and skip Auto Customizations using stylus when it says you have 3 seconds. If you are confident the ROM you have installed is ready to go then fine. We can continue.
3. Now open your Phone Application and go to options and make sure smart dial is off. Then dial ##778 call button (PST/EPST), now click edit and enter six zeros. In the Main Page change the NAM name to Cricket, and enter the MSID/MIN number (that you obtained from your old Cricket phone or from Cricket themselves) make sure its a 10 digit number thats in your area code BUT IT IS USUALLY NOT your PHONE NUMBER. If it was already fine we can continue, if you dont know it you may of skipped obtaining this from calling Cricket as stated above. Now click view info and goto PRL, now check to make sure you have a CRICKET PRL (1013,1014, 1040, 1050 etc.. there are others) If you dont have one loaded in PST and you are using my ROM then you can click in Update PRL File (click in the blank area under setting) and then click Menu, edit, browse and it should go to main root (my documents). Pick PRL 1050 (You may have to try another PRL for *228 to work in step below). Then click ok, then Menu, then ok, it will ask you if you want to update the items click ok. Let it do its thing and restart. If you already have a CRICKET PRL then skip the update PRL step but still make sure to click menu, then ok and let it restart.
4. Now after the phone restarts open phone application again and dial *228 call button (this will make sure base settings are good so i will not have to explain as much, it will also download the proper local EVDO prl to where you are), it will dial cricket and do its programming thing. Do not interrupt this. Let it do its thing even if it restarts. It should say Update complete or Programming complete (if not then try a different Cricket PRL) Now when you are back in action we can continue.
5. Now open the phone application and dial ##778 call button (PST/EPST), now click edit and enter six zeros. Now click view info and goto AKEY and make sure its blank, nothing there. Now click view info and goto NAM settings, NAM name should be Cricket, Mobile Directory number should be YourTenDigitPhoneNumber, MIN1 should be that other phone number the MSID/MIN that is usually not your phone number, but it should be 7 digits, ex: sevendigitnumber, MIN2 should be just your area code. MSID/MIN should be 10digitMSIDnumber <--again usually not yourphonenumber, This part I only know for USA users MCC should be 310, MNC should be 00 (for other Countries you have to look this up), NMSI should be your MSID/MIN (XX10digitnumber<--usually not your phone number) THE XX'S should be zeros, ex: 007185548692, Now if all these settings in this paragraph didnt need touched assuming you didnt skip any of my steps (which they shouldnt be touched i am just making sure) we can move on.
6. Click view info and goto CDMA settings, we are going to make sure they are set right and change a couple things for Clearer voice transmissions, people will compliment how good your phone sounds even in some cases. EVRC should be set at Disable, Home page should be Voice 13k, the Two below it the Same Voice 13k.
7. Click view info click modem settings, change slot cycle index to 1, This will make the phone ring a little sooner, also get your texts a bit sooner. The other 4 options should be Auto, Auto, Enable, No in Order from top to bottom.
8. Click View Info and pick Security, now we are changing this regardless you must do this, we are going to Unauthenticate you and Re-authenticate, it is a Needed step everything in this How To needs to be done and Not skipped! Change the HDR Auth User ID to something bogus like [email protected], the password below it make it something random but remember it, now do the same for PPP user ID and password but make them the same as the HDR ones.
9. Click view info and pick MIP Settings, Make sure Active Profile is on 0, MIP mode should be Simple IP only, MIP reg retries should be 1, MIP reg retry timeout should be 2000 ms, MIP pre-reg timeout should be 30, Mobile Node HA auth should be Disable, send a reg request should be Enable, dormant handoff to disable.
10. Click view info and pick MIP Default Profile, Enable profile should be ENABLE, NAI should be [email protected], MN HA SPI set should be enable, MN HA SPI value should be 12c, MN AAA should be enable, MN AAA SPI value should be 2, reverse tunneling should be enable, home address should be 0.0.0.0, Primary HA address should be 68.28.15.12, secondary should be 68.28.31.12, HA shared secret and AAA secret should be cricket <--lowercase, DMU public should be 0, MN Authenticator should be 0.
11. Click view info and pick MIP customer profile 1 and make sure Enable profile is DISABLED. Now do the same with the other 4 profiles (profiles 2-5), make sure that the only profile enabled is MIP Default Profile.
12. Ok now click menu, ok and let it reset, but make sure not to do anything we are going to be going right back INTO EPST, so when it boots back up open the Phone application and dial ##778 call button (PST/EPST), we are going to re-authenticate you its easy, now click edit and enter six zeros, click view info and goto Security, now change the HDR AN Auth to [email protected], password should be cricket<--lower case, same for PPP user id and Password make them same as HDR.
13. Click view info and goto MIP default profile, make sure the HA, and AAA shared secrets are both cricket<---lowercase, then click menu OK and let it reset.
Thats it! PST settings are perfect for CRICKET, you have a Local EVDO prl file installed, and you are Authenticated for Data and EVDO, now if you used my ROM just go to internet explorer and goto a real page, and follow instructions but remember to click save password! You can also go back into the Phone Application and turn smart dial back on if you choose.
Thats done, every Custom ROM flash from now on should never affect your PST settings and you should always be Authenticated. I hope this helps everyone.
Ryan Mogul
Good write up for this. I have one big problem. when I try to *228, it fails after just a couple of seconds and says,
“The number of SPC attempts failed 15 times from the network. Handset will free for 1 minute and will then reset.” I read a post that was obscure but said that the SPC should be six 0's Mine is not all zeros. I don't know how to change mine to all zeros if that is the case
Thanks
That is the case, for *228 to program your SPC code needs to be all zero's or all 3's (make it zero's though) just follow My Unlock pack and Instructions, it guides you through changing your SPC to all zeros.
Cheers.
RECOGNIZE
Qpst will not recognize my phone
thanks for the great info. as a note, changing the EVRC setting (#7) to 'Voice 13k' kills my phone connection; i couldn't make or receive calls. everything else seems fine!
About Voice 13k Settings
Read the settings again, maybe you missed something.
Check these four settings, also make sure you have used *228 and let it UPDATE your PRL, don't do it manually afterwards. Then check all of the above settings over again and you should be good. I have researched, tested, and used these settings for a long time.
EVRC should be disabled
Home Page should be Voice 13k
Home Orig should be Voice 13k
Roam Orig should be Voice 13k
Since your phone is digital, it uses a codec to determine how the voice data is compressed into digital. Voice 13k (Qualcomm's Purevoice) is the highest voice rate. EVRC (Enhanced Variable Rate Codec) benefits the carriers because it uses a reduced rate, which means less bits to stream, more calls to go around. Voice 13k is in fact the updated version of EVRC that our Digital phones have the option to select from. Voice 13k should be enabled for optimal voice quality.
Take Care
heres why your *228 doesnt work for you..
This is for the User Vickie that needed a little help.
In order to use *228 for Cricket You need to have a Cricket PRL already loaded on the Device meaning installed from PST. You also need the phones SPC code to be all zero's (000000) Then *228 will work fine. It will then update your settings and DL a new PRL if a better one exists. This is for Cricket. If that works out you can follow my settings over again.
hey ryan i have installed your V1.1 Heavy Cricket rom, works great, thxs a lot
neways i was going trough this and i did every step to the letter, now mine didn't work... so i have to ask you a few questions...
first, once i am done with this, and if i did it correctly, i can now make calls and internet right? (hopefully this is yes...)
ok so assuming the answer to the above is yes, then i have to ask.
On step 3, you say if we have your ROM we can just update the PRL from there and to skip the "update step". by update step i'll assume you meant step 4. but then in step 4 you say "for both people who had to restart and people who didnt" and then you say to dial *228
so do we do that even if we already have your PRL loaded?
or do we never have to dial *228 if we have ur prl file?
also, on the profiles, in the M.IP settings, my phone had "6" profiles by default, should i set it to 5 like yours or what?
ok i got everything working beautifully, thanks for the instructions... it's just that i wasn't supposed to dial *228, and i did
anyways, my internet works, and holy cow i get bursts of 2mbps!
well one last thing i gotta ask is... so my calling doesn't work, so i have to call cricket or something to have them switch it to mine right?
on a sidenote, do you guys actually use IE? isn't there like firefox mobile or something??
PST settings are not the Only thing that matters for Internet(WAP) or for MMS. The ROM you are using also has to be configured properly for Cricket WAP/MMS to work. My ROM does but not everyone uses My ROM.
This thread will get your Phone's 1X and EVDO set up correctly. Which will ensure that if your ROM is configured properly that Calls/Text/WAP/MMS will all work. But this thread is NOT the only thing that matters. Read the end of my TOP post and it tells you what the Thread sets up..
Now for your other questions: In this PST settings thread Step 3 says that if you are using MY ROM and the phone doesnt have a Cricket PRL loaded in PST that my ROM has Cricket PRL's copied on it to Update PST with(after updating PST with Cricket PRL phone will soft reset).
This means that YES you need a Cricket PRL loaded(updated) in PST before dialing *228 and then it will restart and then on with the rest of the settings. Dialing *228 gets a local(to your AREA) EVDO PRL loaded in PST(which is downloaded from Cricket Realtime) and sets up base PST settings so that this thread is easier. It explains that in the TOP post at the TOP..
ok in the version of your ROM that i installed, which would be the V1.1 Heavy, it says in that post this:
"Messaging and Connections settings: <--Please do not mess with these as they are fine tuned for CRICKET!! It will always work perfect for you if you leave it alone I cant be responsible if anyone changes anything but you can always post your problems in this thread and I will be more than happy to help sort it out.
"
and this; "Fully working and tested Cricket WAP and MMS/SMS with no problems! I did a lot of tweaks to registry and provisioning to make this possible as the base I used(1.3.4) was originally meant for Sprint!! I pulled a lot of "All Nighters" put it that way lol."
so i thought i don't have to set up my MMS/WAP...
and do i still have to call *228??
***EDIT***
i just called *228, and they said: "sorry we cannot program your phone"
my internet still works... but that's the only thing that works so far, i can't make calls. or send txt msgs.
X-Kenshin-X said:
ok in the version of your ROM that i installed, which would be the V1.1 Heavy, it says in that post this:
"Messaging and Connections settings: <--Please do not mess with these as they are fine tuned for CRICKET!! It will always work perfect for you if you leave it alone I cant be responsible if anyone changes anything but you can always post your problems in this thread and I will be more than happy to help sort it out.
"
and this; "Fully working and tested Cricket WAP and MMS/SMS with no problems! I did a lot of tweaks to registry and provisioning to make this possible as the base I used(1.3.4) was originally meant for Sprint!! I pulled a lot of "All Nighters" put it that way lol."
so i thought i don't have to set up my MMS/WAP...
and do i still have to call *228??
***EDIT***
i just called *228, and they said: "sorry we cannot program your phone"
my internet still works... but that's the only thing that works so far, i can't make calls. or send txt msgs.
Click to expand...
Click to collapse
Ok if you dont understand it just give up. Please quit cluttering up this thread with YOUR problems. a ROM's settings and PST settings are two different things and they both need to be set up right to work!!
MY Cricket ROM is already set up for WAP/MMS, but not everyones version of a Cricket Rom is set up perfect. But your PHONE's PST settings still need set RIGHT as a ROM does not touch that!!
PST settings are independent of ROM settings.
Your problem with dialing *228 is because YOUR SPC CODE IS NOT SET TO ALL ZERO'S!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! SPC code needs to be all Zero's and you need a Cricket PRL loaded (updated) in PST before dialing *228!
It says that in the beginning of this thread. No wonder I am mad. Read well before you follow through
You people seriously have to learn how to read things before trying something. Read, read, read, read, read. Until you fully comprehend what you are trying to accomplish and THEN mess with things.
Edit: My threads are not meant to BABY STEP someone new through the entire process of unlocking, flashing, and programming a phone. NOT AT ALL.. The threads are meant to Help and that is what they do..
ok... wow there
look the reason why i was asking is because you only included this link in your ROM posting thread, you did not include any other links or procedures...
same here, you only include information to do one thing, i see no relevant information pointing to the "other settings" you're talking about.
EDIT:
i had already previously unlocked my phone with another program, but just to double check i used your unlocking pack and followed the instructions. when i run BAF MSL Grabber, it already gives me my MSL code as being 000000, so i am assuming my phone is already unlocked.
but i went ahead and tried to go trough with your thingy anyways, and i got stuck at the ##3424# thing. none worked, ##3424# nor ##3424
i had to use the DIAG(DRMRouter) that took me a while to find in your ROM and i am in QPST right now...
hey Ryan... actually everything works, it's just i was unsure if i still needed to "go down to the store" to get my phone line switched to this new phone with cricket...
neways everything works... including mms, internet, so on so forth. i just haven't tested the gps
Awesome man, I knew I would fuel your fire to get it working. Thats why I am who I am lol. My GPS works awesome. Alot of people dont know this but Agps works with my Cricket ROM. Take care.
Updated the PST settings
I have updated this thread to clear up any problems with New Cricket users that have never had Cricket before. I re-phrased a few things and changed a step so that both New and Current users will not have any problems.
actually about what i said in my last post, i never tested the GPS on the rom so i don't know if it works...
i just know that if i go to google maps, it never locks on to a satellite, dunno why
oh btw, i had to tell yah, the reason why i couldn't dial *228 is because at least in my area, cricket won't recognize the 1050 PRL. everything works with it, but it just won't let me do the *228 thing.
i had to use the 1042 PRL, and then everything worked, just a heads up.
RyanMogul6800 dude not only do I want to say thanks for the settings thread, but your ROMs are awesome. Quick question to anyone who might be able to answer it, this is the first time I get a mogul not to work on mms, i tried all settings, and read through a lot of threads and still no dice, is it possible that the settings might need to be refreshed on the cricket network side? internet and sms work flawlessly, just MMS does not work, it stays stuck at downloading 0%. Thanks in advance!
EDIT: Ok I have ryans heavy rom, and it may seem weird but I installed his mms wap fix from his sig and now it works flawlessly!
Glad you like, but MMS works on MY ROM without that CAB
My ROM works flawless without using the MMS fix CAB from my Shared Site. That CAB is for users not using my ROM or that have messed up their settings on their own.
Now assuming you already have PST set correct and that you are Using MY Cricket ROM.
First thing you do after MY ROM is booted up and running is MAKE SURE ITS UNPLUGGED and WI-FI is OFF! I hate when people leave the phone Cradled for all of their Flashing and Programming. It needs wi-fi off and needs to be unplugged to set up WAP. You need WAP (DATA) set up for MMS to work. So you want to make sure you have unlimited DATA plan with Cricket.
Now after the Phone with MY ROM is unplugged and wi-fi is off simply open up Internet Explorer and Navigate to a real webpage(yahoo.etc) and then enter the info and password click save. Done.
There are some cases after setting up with Cricket needing to call them again and have the account refreshed on their end. There are other instances where Crickets end takes a long time to refresh automatically on their own.
I really believe you ran into a Cricket account refreshing delay problem. Installing the Arcsoft MMS fix cab had nothing to do with why your MMS works now. Do not try uninstalling that CAB to prove me wrong as it will mess up the ROMs settings and will require you to hard reset.
What you could do if you really want to know for sure, is hard reset then let the ROM boot and set up the Internet with phone unplugged. After that I am willing to bet that you can send and receive MMS without installing the CAB we are referencing.
I am glad you like the settings and the ROM.
are you working on a WM 6.5 rom for cricket?
Thanks,
Scott