Related
Hi All,
I had on my Athena the previous Michy Rom (2.04 with SPL 1.20) and when I saw the new version (4.00 with SPL 3.5):
http://forum.xda-developers.com/showthread.php?t=411371
I decided to install it. Like an idiot, I did not pay attention to the fact the SPL was different... I started the flash process and when I realized my error, it was too late.
The upgrade did not completed (as expected :-()) and now I am stuck with a corrupted bootloader screen, so I can't proceed (the device does not boot so I can't access ActiveSync).
Any way forward? Thanks for any hints!
Anubis
Update - I just tried this:
http://forum.xda-developers.com/showthread.php?t=326953
but without success. I get an Error [260] and the entire process stops.
Anubis1965 said:
Hi All,
I had on my Athena the previous Michy Rom (2.04 with SPL 1.20) and when I saw the new version (4.00 with SPL 3.5):
http://forum.xda-developers.com/showthread.php?t=411371
I decided to install it. Like an idiot, I did not pay attention to the fact the SPL was different... I started the flash process and when I realized my error, it was too late.
The upgrade did not completed (as expected :-()) and now I am stuck with a corrupted bootloader screen, so I can't proceed (the device does not boot so I can't access ActiveSync).
Any way forward? Thanks for any hints!
Anubis
Click to expand...
Click to collapse
look here
http://forum.xda-developers.com/showthread.php?t=405814
lakeman said:
look here
http://forum.xda-developers.com/showthread.php?t=405814
Click to expand...
Click to collapse
I have seen that thread. But the problem is different. I have also tried to reload a vanilla WM6 ROM but I cannot go past the corrupted bootloader part...
Anubis
Anubis1965 said:
I have seen that thread. But the problem is different. I have also tried to reload a vanilla WM6 ROM but I cannot go past the corrupted bootloader part...
Anubis
Click to expand...
Click to collapse
When you are in bootloader(three coloured screen) what do you see?
remove sim and sd card , hold camera button all the way in and press the reset button(on the back close to the battery cover)
If you see in bootloader mode ID showing somenting different than ATHE100 the solution is HERE http://forum.xda-developers.com/showthread.php?t=405814
I had the same problem! whell restart your pc and then connect the device to it. now start flashin an spl 1.20 rom. i did it and it worked! I hope i works for you too.
Cheers, Hirad
lakeman said:
When you are in bootloader(three coloured screen) what do you see?
remove sim and sd card , hold camera button all the way in and press the reset button(on the back close to the battery cover)
Click to expand...
Click to collapse
Thanks - already tried!
When I reset/hard-reset the phone (tried many ways) I see a garbled boot image (with random pixels here and there)... It is definitively not the usual bootloader with the information about the various ROM components and the "USB" text at the bottom.
Anubis
Solution!
I managed to do the same thing - had an old AP ROM with SPL 1.2 already installed then earlier today I tried to upgrade to the new Mitchy R4 SPL 3.5. I thought my Ameo was bricked, but after some pain it is now working again.
Here is what I did:
1) Enter bootloader mode using the very tricky Camera+Volume+Reset method.
2)
Follow exactly the steps in post 33 here:
http://forum.xda-developers.com/showthread.php?t=387454&highlight=mtty&page=4
Note, I'm running Vista so to get the USB option to show in MTTY, I had to first open "Windows Mobile Device Center" in Control Panel then disable the USB.
Also, note you should find your MAC under the battery flap.
3) Now all you need to do is reset, enter the bootloader mode again, and re-try the ROM (PS, make sure you use the correct SPL version!
Hope this helps.
spoonter said:
I managed to do the same thing - had an old AP ROM with SPL 1.2 already installed then earlier today I tried to upgrade to the new Mitchy R4 SPL 3.5. I thought my Ameo was bricked, but after some pain it is now working again.
Here is what I did:
1) Enter bootloader mode using the very tricky Camera+Volume+Reset method.
2)
Follow exactly the steps in post 33 here:
http://forum.xda-developers.com/showthread.php?t=387454&highlight=mtty&page=4
Note, I'm running Vista so to get the USB option to show in MTTY, I had to first open "Windows Mobile Device Center" in Control Panel then disable the USB.
Also, note you should find your MAC under the battery flap.
3) Now all you need to do is reset, enter the bootloader mode again, and re-try the ROM (PS, make sure you use the correct SPL version!
Hope this helps.
Click to expand...
Click to collapse
You are right and this is what sergiopi and I were referring to , specifically this post
http://forum.xda-developers.com/showpost.php?p=2154726&postcount=33
We were refering to the whole thread so you could learn the background.
However you are incorrect in your advice about how to enter bootloader
All you need to do is hold in the camera button and reset
spoonter said:
I managed to do the same thing - had an old AP ROM with SPL 1.2 already installed then earlier today I tried to upgrade to the new Mitchy R4 SPL 3.5. I thought my Ameo was bricked, but after some pain it is now working again.
Here is what I did:
1) Enter bootloader mode using the very tricky Camera+Volume+Reset method.
2)
Follow exactly the steps in post 33 here:
http://forum.xda-developers.com/showthread.php?t=387454&highlight=mtty&page=4
Note, I'm running Vista so to get the USB option to show in MTTY, I had to first open "Windows Mobile Device Center" in Control Panel then disable the USB.
Also, note you should find your MAC under the battery flap.
3) Now all you need to do is reset, enter the bootloader mode again, and re-try the ROM (PS, make sure you use the correct SPL version!
Hope this helps.
Click to expand...
Click to collapse
Thanks - you are giving me some hope! I am on a business trip now and my Athena is at home, but I will try that as soon as I am back
Anubis
Hi Guys,
I've been using the ROM from Michy the R4 edition for some days without experiencing any problem and now it occurs that phone function stoped working for unknown reason ! just like that.
Impossible to enter PIN number the connection manager refuse even to open.
I've tried to install different ROM to see if it could change anything but nothing has changed.
I've also no more description of the RADIO I'am using in the about file.
Please help me to save my lovely brick !
i can help u
hi pal i can help u i also had faced the same problem
ur radio board has been dislocated
pm me to make ur baby alive
u an also contact me on phone at +919823291495 or messenger
at [email protected]
What data you have in BL mode ?
callmelolo said:
Hi Guys,
I've been using the ROM from Michy the R4 edition for some days without experiencing any problem and now it occurs that phone function stoped working for unknown reason ! just like that.
Impossible to enter PIN number the connection manager refuse even to open.
I've tried to install different ROM to see if it could change anything but nothing has changed.
I've also no more description of the RADIO I'am using in the about file.
Please help me to save my lovely brick !
Click to expand...
Click to collapse
Hi
Please download the Michy R4.1 and update it it will work. I had the same problem. My advice is "do not use password or pin while you are testing the new rom"
1. Do a hard reset By Vol Down+ reset hole press
2. Get into boot loader By Camera button pressed + reset hole press until you see the tricolour screen.
3. Then flash R4.1
Good luck
Hi Sabes,
I tried to install the 4.1 Rom and it loaded well. I had the boot screen where nothing was writen after the "R" of radio and then I went to the frist setting screen. It then asked to reboot to customize and since that moment black screen. The power led is on and nothing more...
**** ! it sounds like its definitely dead !
I don't understand anything cos I did nothing wrong, no droping, no tweaks, everything was working fine up to some day the phone function stoped working for unknown reason and now I have a black screen.
I have 1.2.
Boot screen shows : Rom = None
I have managed to reinstall the ROM from Michy the R4.1 version and it powers on again.
The problem remain the same = no phone function
When I get to Device Information I have nothing writen after Radio version and Protocol version.
callmelolo said:
I have 1.2.
Boot screen shows : Rom = None
I have managed to reinstall the ROM from Michy the R4.1 version and it powers on again.
The problem remain the same = no phone function
When I get to Device Information I have nothing writen after Radio version and Protocol version.
Click to expand...
Click to collapse
I have a couple of ideas but I would like you to get into the bootloader screen and tell us what you can see there
I have
ATHE100
IPL-v1.00
ATHE100
SPL-v1.20. Olipro
I've been trying the TTY thing but.... :
start NB image download
Fail to synchronize with the host (1)
callmelolo said:
I have
ATHE100
IPL-v1.00
ATHE100
SPL-v1.20. Olipro
I've been trying the TTY thing but.... :
start NB image download
Fail to synchronize with the host (1)
Click to expand...
Click to collapse
I think you have somehow lost your radio or it has become corrupted
Do you have one of the shipped roms?
Try flashing this as i think it includes a radio
even AP3 may have a radio included in the RUU
Flash this while you are in bootloader.
Or you could flash radio 1.58
I've been trying to flash the 1.58 this morning and I was stuck on 0%
I will get to the wiky and try to download the original Rom for my Athena.
Thanks
callmelolo said:
I've been trying to flash the 1.58 this morning and I was stuck on 0%
I will get to the wiky and try to download the original Rom for my Athena.
Thanks
Click to expand...
Click to collapse
Just a thought
have you removed your sim and sd card?
Yes I did...
Just finished downloaded the original Rom I will keep you posted with the results...
Hi,help me pliiiiiiiiz!!!!!
1-my herm100 stuck on windows screen
2-i tried mtty : CMD>task 32
Level=FF
how can i turn it ==>Level=0?????
infos:bootloader:2.03
error 'NO GSM' ???
i tried installing a lot of RUU ROM WM5&WM6 ==>error at 1%
what can i do pliz??help me
hi anf evils
u using a vista pc?
no im using win xp
Try reflashing the SHIPPED STOCK ROM - the rom it came with. This may fix your No GSM problem.
Please note though that once the radio rom gets stuffed it is a SERIOUS pain to get working with a very low success rate.
Good luck...
ultramag69 said:
Try reflashing the SHIPPED STOCK ROM
Click to expand...
Click to collapse
how can i do it, i think that my phone should boot to do it?
my herm stuck on windows mobile screen
and thanks for your replay!
Try a hard reset, hold both soft keys in and reset with stylus. Hold all buttons in until it asks if you wish to reset to factory. Follow directions.
If you haven't already, install Hard SPL, quick search will find it. Then you have to find the ORIGINAL ROM YOUR HERMES CAME WITH... Good luck as this is probably the hardest part...
No guarantees it will work though...
Cheers...
ultramag69 said:
If you haven't already, install Hard SPL,
Click to expand...
Click to collapse
i can not install any hard SPL because i have Level=FF so i can not downgrade to SPL 1.09 or 1.01 (i have now 2.03)
is there solution of this problem
Level=FF??????????????
LEVEL=FF
means that your device is CID locked. I've got the same issue
my HTC3400 has been successfully unlocked and upgraded to WM6.1, cause not stable, so I upgraded the original ROM for HTC3400i with SD card,
when upgrating is almost finished, it stopped, shows "Invalid Certificate, Press any key......."
I have tried to recover it with backup ROM, and downloaded orginal WM5 ROM, and WM6.5, all not work.
I think SPL is wrong.
Now it shows like follows,
ONBL 1.19.0000
SPL 1.19.0000
when connect USB, shows USB on the left bottom.
How can I save it? Help!!!!!!
Thanks in advance.
Take it to the service center. No options left. JTAG may help but that would be too risky if you are an average user.
hehe,i would rather try to solve the problem by myself, so anybody can help me work out the problem.thanks.
tell me first which rom u try to flash ?
first i want to know what u do wrong so it better to solve it
ankit360 said:
tell me first which rom u try to flash ?
first i want to know what u do wrong so it better to solve it
Click to expand...
Click to collapse
i wish upgrade WM5.0 official ROM.thanks.
the story is complicated.
1)original is WM5.0
2)unlocked with gene_hspl.exe successfully.
3)upgrated with SD to WM6.1 successfully.
4)i downlaoded HTC3400i official ROM WM6.1, it remember the version is 6.1, i upgraded with SD, the upgrading is almost finished but stop and showed "Invalid Certificate, press any key to......"
5)whatever ROM i want to upgrade with SD or USB cable, all failed, including backup OS.nb+extrom.nb.
if try to upgrade with SD, showed "Invalid Certificate......", if try to upgrade with USB, showed only 2% or 3% then power on
6)when enter tricolor with ONBL 1.19.0000 and SPL 1.19.0000, "USB " shows on left bottom.
ok, what can you do?
sunnyhuang said:
i downlaoded HTC3400i official ROM WM6.1
Click to expand...
Click to collapse
enplane me from where u get this ?
ankit360 said:
enplane me from where u get this ?
Click to expand...
Click to collapse
i download from internet, from a chinese forum.
Heh, trying to solve it yourself ? There is no official WM 6.1 ROM for P3400i from HTC otherwise we wont be moaning here for 4-5 months and given our 40-50 nights for porting WM 6.1 to gene. What you have flashed is something wrong and that has messed up your SPL CID as well as ONBL.
Anyways, Try if you can solve it yourself or get it solved somewhere
I have a problem:
I flashed my hd2 from a stocked rom 1.42 dutch version, with hspl 1.42. I installed a custom rom from: HTC HD2 Laurentius WWE 21891UltimatePOWER.
it worked fine for 2 or 3 days and then it stocked, i reseted the phone and
When i turn on my HD2, i get a white screen. and it doest go away. Even after softreset (volume button down in bootloader)
When i go in to bootloader i see this screen:
Pb81100 hx-bc
Spl-1.42.hspl xe
0x05
Cotullahspl 0x30
Click to expand...
Click to collapse
When i try to instal a rom by going in to bootloader en then start in win xp the update wont start, it stocked at 0 %
Then i tried to flash a orginal romt by sd:
it stocked at 7 % and i get this screen:
_______________________RUUNBH
PB81100___HX-BC
SPL-1.42.__hspl___XD
________________0x05
CotullaHSPL______0x30
Upgrade ROM code error
Please try again
Click to expand...
Click to collapse
- Then i tried to flash a radio rom by activesync, in xp it wont start,
- i tried flashing by sd and it stocked on 98%
- I tried different to install a rom and radio rom by vista, but also no succes
- I tried task 29 (by the Attached Task29 into a single exe.) to erease all data from the phone, but in windows by activesync it wont start
i tried al the above from windows 7.
Is there anyone that can help me, please i getting very desperate.
VERY VERY IMPORTANT! Try and read 2-3 times what is written here http://forum.xda-developers.com/showthread.php?t=609477
Only afterwards proceed to the following :
First of all....try and use Windows Vista or Windows 7.
Second of all....do not try to use task 29 because its a bit more complicated and it involves some drivers and so on!
Use this little thing here http://forum.xda-developers.com/showpost.php?p=5848003&postcount=19 and after its completed....flash a proper radio something like 2.08.50.xx which you can find on Radio dedicated section here http://forum.xda-developers.com/showthread.php?t=611787
After all these....flash a custom ROM but be careful to be one suited with your radio! Which is a radio appliable for most of custom ROMS BUT be VERY careful!
Another thing.....do not flash from SD Card....Use the CustomRUU tool and flash it via ActiveSync!
Do you get any particular error message? When in bootloader mode, does "usb" show at the bttom of the screen? If so, try moving to a different usb port, preferably at the rear of the pc, or try different cable or even different pc. If still no luck, try uninstalling and then re-installing the latest version of Activesync.
The White Screen issue sounds like the incorrect radio version for the rom. I'm not familar with the details of the particular rom, but there are certain rom/radio combinations that will do that if they do not match eg running a 2.10 based rom with a x.xx.51.xx radio. The phone works intially until a reset and then hangs.
viperd said:
VERY VERY IMPORTANT! Try and read 2-3 times what is written here ......
Click to expand...
Click to collapse
Thanks for the replay
I tried, flashing by activesync. i flashed it the first time by hspl (the tread you link to) and then by activesync. But like i said, the hd2 stops at a white screen, so i tried by every possible way i could think of. Also i tried task 39 by the tool you mention, but it still does not work.
But i will correct my ts.
@clydeb1
I tryd to flash different radioroms, but if it try by activesync it wont start and by sd-flash it stocks at 98%, but i will try a different active sync
Okay,
I tried the following options:
- I installed a newest activesync and tried to instal an new rom under windows xp. The update stocked at 0% and i tried to install radio rom, with the same results
- I installed the windows mobile on windows 7, and tried the same as in windows xp, and still the same results.
Then i tried flashing every rom from the site by the sd-method (after every bad flash i formatted the sd-card with fat32)
With the sd method the phone stocked at 99% and then gives the next images:
00018003
LEOIMG.nbh - Fail
Radio_V2Fail
Update terminate
update fail
Click to expand...
Click to collapse
IS there any one how has a solution for this problem
Ok....try from the beginning!
1.Get from here http://forum.xda-developers.com/showthread.php?t=611433 HSPL2_RUN.zip (extract the content in a folder named hspl ).2
2. For Windows 7 you need Windows Mobile Device Center ( WMDC ) NOT ActiveSync!! Get it here http://www.microsoft.com/windowsmobile/en-us/downloads/microsoft/device-center-download.mspx
3. Make sure in WMDC settings the USB connection is checked!
4. Take out your battery....insert it again! Start your phone while keeping pressed the Vol Down button! This will get you into bootloader! The screen should display USB on the lower part of the screen! (evidently connected to computer )
5. Flash HSPL2 select 2.08 version
6. Use that tool I recommended earlier.....http://forum.xda-developers.com/show...3&postcount=19
7. Enter again the bootloader and flash a Radio ROM ( try 2.08.50.xx ) via WMDC!
8. Flash either NRGZ 21898 or Cleanex 21898 versions ( I recommend these in particular because they work with the radio mentioned above and are also stable ROMs ).
P.S. Take out your SD card and SIM card while performing all these steps!
Hope you will solve it!
viperd said:
Ok....try from the beginning!
1.Get from here (extract the content in a folder named hspl ).2
2. For Windows 7 you need Windows Mobile Device Center ( WMDC ) NOT ActiveSync!! Get it here
3. Make sure in WMDC settings the USB connection is checked!
4. Take out your battery....insert it again! Start your phone while keeping pressed the Vol Down button! This will get you into bootloader! The screen should display USB on the lower part of the screen! (evidently connected to computer )
5. Flash HSPL2 select 2.08 version
6. Use that tool I recommended earlier.....
7. Enter again the bootloader and flash a Radio ROM ( try 2.08.50.xx ) via WMDC!
8. Flash either NRGZ 21898 or Cleanex 21898 versions ( I recommend these in particular because they work with the radio mentioned above and are also stable ROMs ).
P.S. Take out your SD card and SIM card while performing all these steps!
Hope you will solve it!
Click to expand...
Click to collapse
Thanks for the advise
I did every step. The first problem is: WMDC doest say there is a connection, while windows 7 say there is a connection also i see usb in the lower part of the screen.
In the same sequence as you right above. the hspl2 says it worked fine, but when i reset the boatlooder still says it has hspl 1.42 in stead of 2.08. The tool you recommended did't start. and says update error.
do you know something else i could do (or anyone else)
Give the phone to someone who can get it to work??
Give me your SD-CARD serial number.
I'ma make a goldcard for you.
sd-card max to 4gb!
And then try flashing stock nld 1.66 rom using sd-card.
Because you tried to fix it flashing a 'original rom?' from sd I think I know what's your problem.
Did you use a Dutch shipped rom while trying to fix or a WWE one?
If you flash a shipped rom from storage card it restores the original SPL and removes HSPL !
Try flashing a Dutch shipped rom one more time from storage card, it will restore the original SPL made for your device.
korenbloem said:
Thanks for the advise
I did every step. The first problem is: WMDC doest say there is a connection, while windows 7 say there is a connection also i see usb in the lower part of the screen.
In the same sequence as you right above. the hspl2 says it worked fine, but when i reset the boatlooder still says it has hspl 1.42 in stead of 2.08. The tool you recommended did't start. and says update error.
do you know something else i could do (or anyone else)
Click to expand...
Click to collapse
Thanks mate, if my suggestion doesn't work hopefully you can help him.
xmoo said:
Give me your SD-CARD serial number.
I'ma make a goldcard for you.
sd-card max to 4gb!
And then try flashing stock nld 1.66 rom using sd-card.
Click to expand...
Click to collapse
@Korenbloem,
A simple hardreset would have fixed your issue as well.
Instead of all kind of panic experiments like mtty/ flashing radios/roms from sd you could have come to me and I would have helped you.
You flashed a very old rom from the rom archive but never the less that rom is intensivily tested by me and the beta team.
I have no idea what kind of software you installed/tweaks you did or anything else but also with installing the wrong software it could cause the rom not to boot anymore.
Sorry to tell you but these 'bricking' stories are mostly caused by unexperiened users and it
making me sad to see more people are opening threads like this blaming a rom and causing a panic reaction in public destroying our work.
I realy hope you fix your device and I will try to help you but this isn't a rom issue.
Leo
Laurentius26 said:
Because you tried to fix it flashing a 'original rom?' from sd I think I know what's your problem.
Did you use a Dutch shipped rom while trying to fix or a WWE one?
If you flash a shipped rom from storage card it restores the original SPL and removes HSPL !
Try flashing a Dutch shipped rom one more time from storage card, it will restore the original SPL made for your device.
Click to expand...
Click to collapse
Thanks for the adivse, but i already tried that with an orginal rom, but i will try it again, mabey there is a difference with a shipped rom.
The first thing i did was a hard reset, but that did't worked. (the phone is in this shape for 1 month now).
Second. I am not blaming you or anyone. I flashed the wrong radio rom i think (cant remember witch one) And that is my own fault. I never wanna make the suggestion that it is because of youre rom.
I took a risk by flashing my phone. and i is my responsibility.
Edit: I tried a shipping rom nld. But it gives the same error as always, only after 7%. But thanks for the advise
@ Xmoo, First of al thank you that you want to help with a sollution. But what does that mean a goldcard and what are the consequences of using it.
Laurentius26 helped me with fixing my device.
The problem was the radio. and by flashing a factory rom from t-mobile, the hspl was reset to spl 2.00. After that he flashed a orginal shipped rom (the orignal one from my device). And the rom is fixed again SPL 1.66 is now on the device.
Laurentius thanks for al the help!!!!!
HD2 bricked?
Hi, I urgently need your help. I used my hd2 on a vodafone branded rom 1.44. Last week I installed a Vodafone NLD 1.72 rom , + froyostone 3.4 Rom,kernel 8.5 (with hspl). Yesterday my touchscreen has stopped fully .. . The next, I've been in touch with HTC and they will pick up my phone tomorrow for repair. I have to remove hspl ofcourse .. so I happily try to flash official vodafone rom from the SD card, did nothing 1.72, 1.48 seemed to do until I restart and got an ROM code error. What to do: ( I am pretty desperate now .. when you start you get an exclamation point and then 'not allow' and then the tricolor. Is this due to the lack of the original 1.44 ROM? Apologies for this begging post and my poor English but I hope that someone has a solution to unbrick this device so he can up picked by HTC.
vanbasten88 said:
Hi, I urgently need your help. I used my hd2 on a vodafone branded rom 1.44. Last week I installed a Vodafone NLD 1.72 rom , + froyostone 3.4 Rom,kernel 8.5 (with hspl). Yesterday my touchscreen has stopped fully .. . The next, I've been in touch with HTC and they will pick up my phone tomorrow for repair. I have to remove hspl ofcourse .. so I happily try to flash official vodafone rom from the SD card, did nothing 1.72, 1.48 seemed to do until I restart and got an ROM code error. What to do: ( I am pretty desperate now .. when you start you get an exclamation point and then 'not allow' and then the tricolor. Is this due to the lack of the original 1.44 ROM? Apologies for this begging post and my poor English but I hope that someone has a solution to unbrick this device so he can up picked by HTC.
Click to expand...
Click to collapse
Do you have a branded Leo? If so, enter bootloader (remove battery, press volume down, insert battery), connect via usb (maybe you have to wait for driver installation), start the latest *.exe from your operator/carrier...
same problem here flashing an old radio... and now, everytime i try to flash a factory rom ship (RUU_Leo_HTC_PTG_1.66.410.1_Radio_Signed_15.30.50.07U_2.06.51.07_Ship) on 1% get the error 244 - invalid model id.
I tried to hard reset and now the message on the bottom of screen show me the right factory radio (2.06.51.07) of this rom but stays on this screen forever anyone knows what can i do? please help... tks a lot!
andreftx said:
same problem here flashing an old radio... and now, everytime i try to flash a factory rom ship (RUU_Leo_HTC_PTG_1.66.410.1_Radio_Signed_15.30.50.07U_2.06.51.07_Ship) on 1% get the error 244 - invalid model id.
I tried to hard reset and now the message on the bottom of screen show me the right factory radio (2.06.51.07) of this rom but stays on this screen forever anyone knows what can i do? please help... tks a lot!
Click to expand...
Click to collapse
Maybe it is because you flashed the wrong stock rom.
You should find the CORRECT STOCK ROM for your device, otherwise you need a gold card
silverwind said:
Maybe it is because you flashed the wrong stock rom.
You should find the CORRECT STOCK ROM for your device, otherwise you need a gold card
Click to expand...
Click to collapse
sorry but this rom i've downloaded from htc.com after insert model and my hd2 serial number and work for a while, but after flash hspl 1.42 to install another rom, when i flash a new radio version get the problem! so i flash again hspl to recovery for SPL 1.42.000 and then, nothing more is functional
tks 4 help... have anyone other solution?
andreftx said:
sorry but this rom i've downloaded from htc.com after insert model and my hd2 serial number and work for a while, but after flash hspl 1.42 to install another rom, when i flash a new radio version get the problem! so i flash again hspl to recovery for SPL 1.42.000 and then, nothing more is functional
tks 4 help... have anyone other solution?
Click to expand...
Click to collapse
The 1.66 ROM you posted above has radio version 2.06.51.07 with it. So have you considered trying to flash that radio version and then flash the ROM. I know if you get the ROM to flash it will flash that radio anyway. But you seem to think you flashed a wrong radio so just thinking out loud here.