Hello,
I cant flash any radio to my Hermes, I tried several version and its always on 0%, I also upgraded bootloader to 2.10.Olipro and it didint helped. When I'm trying to flash after ~1 minute im getting error message about connection problems and getting Recovery. I also tried HERMflasher for linux but it just makes white screen on my Hermes and no progress at all (I waited almost hour). Whats funnier I can load any custom OS (still no radio and protocol) but if I try to load any original it hangs on 12% Any ideas?
Try flashing on another computer if you can.
I could not flash anything on my primary desktop. All I would get are hangs, errors and recovery messages. I moved everything over to my laptop and it flashed fine. Both running XP with all current updates.
Possibly a problem with a piece of software eg.. Antivirus, Spyware, Firewall, other. Driver problems for USB or other hardware causing conflict.
If your boot loader is 2.10.Olipro, you have HardSPL.
If you have HardSPL, when why the heck are you still trying to flash the phone using a USB cable?
Go check the wiki and read the instructions on flashing from an SD Card.
hey i got same problme with my hermes its no radio in my phone menas no GSM
is it possible to flash radio with sd card ????
chiragpatwa said:
hey i got same problme with my hermes its no radio in my phone menas no GSM
is it possible to flash radio with sd card ????
Click to expand...
Click to collapse
Yes it is. Same procedure as with a ROM. (rename the file, put it on the card, etc)
I still can't flash radio, it hangs on around 10%. Any ideas?
Hi Folks,
I'm stuck in the tri-color screen for bootloader 1.06.
I have DCD 3.2.0 w/3.42.02 radio on the XV6800 and was trying to upgrade to radio 3.42.30. My system is Vista 32-bit.
I ran the Titan Relocker and it put SPL-1.06.0000 back onto the device and was planning on then putting 1.2 onto it.
Running titan_exitbl.exe says "Cannot open USB port. Please make sure, that USB connection in ActiveSync is disabled."
Unfortunately it is now stuck and even after ending the Sync Center service I can't get titan_exitbl.exe to pull it out of the Boot Loader.
Ideas? Thank you!
I could fire up an old XP laptop and try it from there.
Loaded ActiveSync 4.5 on an XP laptop, disabled USB connections, ran titan-exebl.exe and the device is booting now.
I'll continue on and see what else I can screw up.
Loaded SPL 1.20
Loaded 3.42.30
Loaded SPL 2.40
Device is back to working! Off to see if GPS is back after being lost with 3.42.02.
titan-exebl.exe
Where can I find titan-exebl.exe? Google doesn't turn up any results other than here?
titan_exitbl.exe
Never mind... just located it on my own hard drive!
Cheers!
Stuck on Bootloader
OK... I've tried titan_exitbl.exe, and it still doesn't work.
Here's my problem in chronological order:
1. I've been having a few problems (bugs) in my current custom ROM (PPC Kitchen 3.49 version), so I decided to re-flash to a stock ROM, see if the problems were fixed, and then try to flash back to a custom ROM.
2. I tried flashing to the Sprint 3.35 ROM. The RUU showed the progress bar on both my PC and the phone. But at 0%, I got a message saying "an error has occured" - or something to that effect.
3. I decided that the error was because I was running a custom ROM, and Sprint didn't like that. So I ran the Titan Relocker utility, thinking this would cure the problem.
4. I followed the steps on the screen and then got a message saying the relocker utility had completed successfully. The phone rebooted and went into the tri-color bootloader mode.
5. I retried the Sprint 3.35 ROM update, but got the same connection error, and the progress slider would never move from 0%.
6. I decided the phone had locked up and performed a reset with the stylus. The phone rebooted and went back into bootloader mode. The screen shows "TITA100 SPL-1.06.0000"
7. And that's as far as I've gotten. I've tried several hard resets using the buttons and the stylus together. I've tried removing the battery and reinstalliong... but the phone just goes back into bootloader mode.
I've tried both titan_exitbl.exe and UNI_Exitbootloader.exe, and neither utility seems to help. I get a message saying that "All data was sent... the phone will reboot now... please check your screen". The phone's screen blinks for a moment, and then returns to bootloader. Nothing can get it anywhere else.
I've tried different USB cables and ports. Activesync won't detect it, but the utility update software does.
When I run the Sprint 3.35 ROM update utility, I get an error at 11% saying "invalid vendor ID" and the update refuses to run. I tried to run the Titan Re-locker utility again, but it requires an ActiveSync connection. I've tried both enabling and disabling the USB connection in ActiveSync, but that seems to make no difference. The utility simply says no USB connection is available. The ROM update utilities will detect the device via USB - they just refuse to work with them.
I also tried running a DCD Tital 2.1.0 Bell ROM. The progress slider freezes at 0%, and then I get a message saying the RUU has encountered communication errors during the update. I've been through the recovery process the utiity suggests about a dozen times... it sill returns the phone to the bootloader screen.
So I'm getting pretty frustrated... does anyone have any ideas?
Try changing your spl back to 2.40.
Throwing it back into the tri color screen again and flash the sprint stock 3.35
But put it on the root of a fat32 formatted micro sd card in the flavor of under 2gb.
Just run the exe from your computer it will extract the files from the exe to some location on your computer, normally the ruu update folder.
There will be a ruu_sighned.nbh file locate it and copy it to the fat32 formatted card rename it TITAIMG.nbh
Let the phone boot into the bootloader and it should detect the file on the sd and update the rom for you, by stating loading ......
Then will prompt you to update press power key.
Sense you are not on sprint don't let the first time custimizations run ... pull battery once you get to your mobile today screen on first boot...
Use active sync or the sd method to update your rom to whatever you wanted originally.
Most full updates from carriers the ones that flash both the radio and rom will run regardless of the boot loader thats on the device.
Happy flashing
Just thought I'd toss in here that GPS does work, but I have to use GPS Viewer to get a lock on the satellites first.
softwind said:
OK... I've tried titan_exitbl.exe, and it still doesn't work.
Here's my problem in chronological order:
1. I've been having a few problems (bugs) in my current custom ROM (PPC Kitchen 3.49 version), so I decided to re-flash to a stock ROM, see if the problems were fixed, and then try to flash back to a custom ROM.
2. I tried flashing to the Sprint 3.35 ROM. The RUU showed the progress bar on both my PC and the phone. But at 0%, I got a message saying "an error has occured" - or something to that effect.
3. I decided that the error was because I was running a custom ROM, and Sprint didn't like that. So I ran the Titan Relocker utility, thinking this would cure the problem.
4. I followed the steps on the screen and then got a message saying the relocker utility had completed successfully. The phone rebooted and went into the tri-color bootloader mode.
5. I retried the Sprint 3.35 ROM update, but got the same connection error, and the progress slider would never move from 0%.
6. I decided the phone had locked up and performed a reset with the stylus. The phone rebooted and went back into bootloader mode. The screen shows "TITA100 SPL-1.06.0000"
7. And that's as far as I've gotten. I've tried several hard resets using the buttons and the stylus together. I've tried removing the battery and reinstalliong... but the phone just goes back into bootloader mode.
I've tried both titan_exitbl.exe and UNI_Exitbootloader.exe, and neither utility seems to help. I get a message saying that "All data was sent... the phone will reboot now... please check your screen". The phone's screen blinks for a moment, and then returns to bootloader. Nothing can get it anywhere else.
I've tried different USB cables and ports. Activesync won't detect it, but the utility update software does.
When I run the Sprint 3.35 ROM update utility, I get an error at 11% saying "invalid vendor ID" and the update refuses to run. I tried to run the Titan Re-locker utility again, but it requires an ActiveSync connection. I've tried both enabling and disabling the USB connection in ActiveSync, but that seems to make no difference. The utility simply says no USB connection is available. The ROM update utilities will detect the device via USB - they just refuse to work with them.
I also tried running a DCD Tital 2.1.0 Bell ROM. The progress slider freezes at 0%, and then I get a message saying the RUU has encountered communication errors during the update. I've been through the recovery process the utiity suggests about a dozen times... it sill returns the phone to the bootloader screen.
So I'm getting pretty frustrated... does anyone have any ideas?
Click to expand...
Click to collapse
please i have this problem how to fix this?
Please state your exact problem and what you did to cause it. Including all versions of rom and radio and bootloader.
drewcam888 said:
Please state your exact problem and what you did to cause it. Including all versions of rom and radio and bootloader.
Click to expand...
Click to collapse
Thanks!!! Ok, i cant remember eactly what is the v radio but i think 3.35 or 3.42 i cant remember exactly it's one of these. the SPL 1.06 Locked i cant unlocked i cant use titan_exitbl.... the SD update doesnt work stuck on loading.., i cant update from pc stuck 0% then Recovery Error help me. I My phone is bricked? Sorry for my english....
Did you try to install 2.4 unlocker?
drewcam888 said:
Did you try to install 2.4 unlocker?
Click to expand...
Click to collapse
Yes, i try from SD and nothing stuck on loading... from windows with RUU nothing 0% stuck and then UPDATE ERROR[262] now i don't know to do
2.4 doesnt use sd and it is run from a .exe. Make sure you aren't trying 2.47. Are you sure you tried this?
drewcam888 said:
2.4 doesnt use sd and it is run from a .exe. Make sure you aren't trying 2.47. Are you sure you tried this?
Click to expand...
Click to collapse
Ok, but how run from windows? If i cant connect via activesyncs the phone is on SPL mode i cant out of that and the msdos windows say "No device conected" when press enter from windows i cant unlock. Any idea? I'll try 2.47 but how run from windows with the phone en SPL Mode?
Please read. I said run 2.4 not 2.47. Put the phone in bootloader and it should say usb at the bottom. Then run 2.4 .exe unlocker. I think it should run without using activesync. And by spl mode do you mean the phone is in the bootloader.
drewcam888 said:
Please read. I said run 2.4 not 2.47. Put the phone in bootloader and it should say usb at the bottom. Then run 2.4 .exe unlocker. I think it should run without using activesync. And by spl mode do you mean the phone is in the bootloader.
Click to expand...
Click to collapse
Look i cant run Hard-SPL-MFG (Olipro 2.40 Unlocker) because when i run the Bat Or MSDOS Windows say "No device connect" question me if i want retray copy the file.
Ok so i guess it needs activesync. About your only option is to install a pregps rom so the phone will boot and then you can reflash the custom rom. Below is a pregps Verizon rom and radio that will work for 1.06 bootloader. Called rom 2.09.
http://forum.ppcgeeks.com/showpost.php?p=834294&postcount=4
drewcam888 said:
Ok so i guess it needs activesync. About your only option is to install a pregps rom so the phone will boot and then you can reflash the custom rom. Below is a pregps Verizon rom and radio that will work for 1.06 bootloader. Called rom 2.09.
http://forum.ppcgeeks.com/showpost.php?p=834294&postcount=4
Click to expand...
Click to collapse
No luck, method A SD Card Loading.. then cheking... then show a number corner 00028002 and say down Not allowed.
Method B, via PC and RUU then ERROR INVALID VENDOR ID.
Any idea? Thanks bro.
I think my phone is bricked... noway load the rom... i've tried load bootloader unlocked via SD last option and nothing!! damn this is so
I screwed up my ATT8525, by trying to upgrade it. Here is what I did in sequence:
1. I used HTC_Hermes_SIM_CID_Unlock_v3a, and I first unlocked the phone, it was pretty straight forward.
2. I installed HTC version of ROM HTC_TyTN_WWE_3.54.255.3_6275_1.48.00.10_108 .. It worked fine except for sound . Because of sound I decided to go to back to a lower version WM5.
3. I installed HERMIMG_Qtek_WWE_1.18.255.3_Ship.nbh, using a RUUWrapper.
So now the phone gets stuck booting in Windows Logo screen. Is there any way to flush the ROM without Active Sync? Does anyone know of any other option of flashing ROM?
All info is here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeForBeginners
1st thing, Whats your SPL? If you don't have Hard SPL installed you need a boot up the bum...
Untick "Allow USB Connection" in the Activesync settings on the PC. Go to bootloader, connect via usb and run the HTC_TyTN_WWE_3.54.255.3_6275_1.48.00.10_108 ROM RUU_Wrapper.exe again... This should get you a bootable version of windows as it worked before.
INSTALL Hard SPL if you don't have it (I believe it will only be 1.10 as you've unlocked your phone) - your SPL should be 2.10 oli...
Then if you need to, you can use the sd card to flash anything.
You may have "unlocked" your Hermes but you may not have superCID it meaning that even though you can use other sim cards you can't install other ROMs for different carriers... Hard SPL fixes this.
i'm sorry.... i still don't understand...
I recently upgraded my xv6800 with the MR2 upgrade from the PCDphones website and experienced several freezes in the week following until it locked up last night and refused to boot back into Windows Mobile. At this point, when I restart it, it loads upto the Verizon Wireless website and hangs there. I can restart it and get to the red, green and blue bootloader screen. I've never unlocked the bootloader before and the code there is SPL-2.07.
What I'd like to be able to do is get any ROM loaded onto it, whether it's a custom ROM or one of the Stock Verizon ROMs. I cannot connect with ActiveSync, though when I have the bootloader screen up, the computer recognizes that a PDA is connected and installs some type of driver. I attempted to re-run Verizon's upgrade utility for the MR2 Update, though it failed to recognize the device. I read in one forum that if I could get to the bootloader screen, I wasn't necessarily bricked, though I'm not sure how I can get to the point where I can flash the stock ROM with a locked bootloader.
Any help would be greatly appreciated!
Flash by sd card and not by usb. Card must be 2gb or under. You can extract the rom from the mr2 .exe by using winrar. Then put the renamed image file on the sd card and flash. Below are instructions for unlocking after you get out of bootloader.
http://forum.ppcgeeks.com/showthread.php?t=33857
Got a problem. I wanted to upgrade to new OzRom today so did normal tasks I did last 40 times.
get new rom and unpack it.
Rename image to LEOIMG.nbh and put it to root of SD card
perform mtty task 29
reboot, phone goes to bootloader then goes to normal grey screen it just says loading and that is it. It gets stuck there.
I had tried flashing via sspl, it sees the phone, screen on phone changes to black htc screen but loading bar sticks at 0%
I have HSPL 2.08 on the phone, I tried to re apply HSPL but it states error with usb connection. Can not upgrade radio from sd card or via sspl as well.
Did try previous rom that worked but it also does not want to load?
Any ideas?
Try flashing back to your original rom. Try that via sd card which should replace hspl back too your stock spl and then start the process from scratch.
mitty task 29 has a serious problem. you are not the only one. if ur hd2 is from tmobile. try T-Mobile_HD2_MR_Software_2.13.531.1. flash it just like the way you do. if doesnt work then copy it to sd card and flash it. . it'll return to its original stage.
pnjboyzz said:
mitty task 29 has a serious problem. you are not the only one. if ur hd2 is from tmobile. try T-Mobile_HD2_MR_Software_2.13.531.1. flash it just like the way you do. if doesnt work then copy it to sd card and flash it. . it'll return to its original stage.
Click to expand...
Click to collapse
It is odd that it did it now as I have not had any problems for last 8 months
Did not work!!
Update is that I managed to do the HSPL3 again over USB which I could not do before but I can not flash any roms.
Have you tried flash to ActiveSync????
Ok got it going again.
I hade my HSPL as 2.08.0000 and cotula signs all over it. Flashed again and it again went to the same one. However apparently .0000 means it is stock (no idea why stock rom did not want load). Flashed it again to HSPL2 and then upgrade to 3 fixed it.
alesscam said:
Have you tried flash to ActiveSync????
Click to expand...
Click to collapse
It would not help as I have done mtty before so no os on it.
no problem with mtty...
after mtty
you can press red botton for sofreset and press volume down for go to Bootloader
from bootloader you will see USB ,
this if your leo is connect to PC