Related
My phone came across some issues. Don't ask how. I have a few issues and heard this is place to go. Here goes.
I tried to turn my phone on.
It vibrated, the green light turns on, but no display.
So I turned it on to the Bootloader screen (it's the only display I have). It reads:
"TITA100 MFG
SPL-2.40.Olipro
CRLD-9"
I connect to the computer, and I hear the chime to confirm its connection.
However, I open Mobile Device Center and it doesn't show that a phone is connected. I go to to Device Manager, and I see that there is a "Microsoft USB Device" connected, which is my phone.
So in all, when I try to flash a new ROM, it tells me there's a connection error. However, it knows my phone is there because the phone's screen changes. HOWEVER, when the flash is operating, it tells me what ROM its flashing to. It does not tell me the image I have though, which leads me to suspect I don't have a ROM at all on my phone.
I'm dead confused as to what to do. Everyone has an actual OS to use and to connect to Mobile Center (activesync). So...help me out if you can?
I don't want my little baby to die.
...come on...breath Mogul...it'll be ok.
You have unlocked your phone and have the 2.40 bootloader installed which is suitable for the 3.35.xx and later based ROM builds. You must also match your chosen ROM with a suitable radio.
Activesync will only make a connection when you are booted into Windows Mobile. For flashing, that connection is only necessary to unlock/lock your phone and change the bootloader.
You are fine, but are not telling us what you are trying to flash to or what information you are following to flash. If you read the sticked threads on the front of the forum and check out and follow the instructions posted in the Titan Wiki for upgrading to the latest GPS/EDVO Rev A ROMs, you should find all the links and information you need to successfully upgrade your phone.
Thank you very much.
I thought I was stuck.
I think I'm going to upgrade to the latest ROM and try to get it running. This leads me to a new question:
Is there any special step I need to take when wanting to Flash using the SD Card? The ROM, let's say 3.35 Alltel. I put it in the card and it says "Loading", then it shows the number "00068002" in red up top, and then the blue words "No Image File!" appears.
Alvaster said:
TIs there any special step I need to take when wanting to Flash using the SD Card? The ROM, let's say 3.35 Alltel. I put it in the card and it says "Loading", then it shows the number "00068002" in red up top, and then the blue words "No Image File!" appears.
Click to expand...
Click to collapse
You are missing out a few steps in telling us what you have done. Tell us exactly what you are doing and with what type of card.
Alrighty.
I have a 1 Gig card, FAT32 1024.
I'm trying to get the "Alltel 3.35.671.9 ROM".
I read that I am to flash that ROM first, but like I said, the progress bar shows up on my phone when flashing with the .exe program (gray background, progress bar up top), and then it gives me an error message and I have to reset my phone and go through the tedious "recovery" process.
When I try to use the SD Card to install the Alltel image 3.35.671.9, it says Loading, and then No Image!, and it takes be back to the BL screen.
Is that enough?
Thank alot.
As you have apparently have a suitable SDcard, you don't need to bother with the Alltel ROM. You can directly flash a suitable discrete radio ROM (links in the Wiki to 3.37.20 & 3.39.10). Less hassle that way and the best method for future radio changes without affecting your data or OS ROM. With the CDMA Radio upgraded you can then repeat with the SDCard routine to flash to one of the later third party ROM or kitchen build of your choice. After that, all should be fine to boot into the new OS.
Remember that the ROM file copied to the root of the SDcard must be renamed TITAIMG.nbh.
Damn it all.
I put the card in with the Radio in it, named "TITAIMG.nbh", and it only reads "loading" then "No image file!"
I tried both Radios, and my card is fine.
Still no luck.
Geez...what a disappointment. Thanks for your help though. I feel safer knowing there's hope for the thing.
Did you format the card into FAT32 from your PC?
Oh well, I guess again resort to using the latest Alltell or Sprint ROM via the USB to upgrade your radio. Rather than using their installation routine you can again extract the ROM image but now manually initiate the ROM Update Utility as described in the Wiki.
Thanks again for the tips and info.
Sadly, flashing by SD always gives me a "No Image File!" message, and flashing by USB always gived me a 262 Update Error message, no matter how many times/ports/resets I do.
I guess I'm stuck then.
Hello,
I hear nothing but great things about custom ROMS, especially DCD and would like to try one. I have spent the last few weeks reading all the threads located here on XDA-Developers and on PPCGeeks regarding upgrading an OEM Verizon XV6800 to a custom ROM.
Below are the instructions I have come up with. I would appreciate it if this wonderful community could provide any suggestions or corrections to my steps. Based on your responses I will create a finalized guide for other users to follow.
I have received very mixed results regarding the overall procedure. Some say you must first flash the Sprint ROM and then flash DCD (To upgrade the radio). Others say you can just flash radio 3.39 and then flash DCD 3.1.6. My below steps are going on the assumption you can just flash the radio 3.39 and then flash DCD 3.1.6.
Phone has
Software Version: 2.09.605.8 (I believe this is the ROM version)
Firmware Version: 1.30.60 (I believe this is the radio version)
I have doccumented my
NAM, SCM, ESN (Hex & Decimal) and MSID.
1. Backup everything
2. Connect the phone to the computer using USB cable and ensure it can establish an active sync connection.
3. While the phone is connected to the computer and running Windows Mobile 6.0 run titan_SPL_2.40-olipro.exe to unlock the phone.
4. Reboot the phone and put it in to bootloader mode (Hold down Power button, camera button and press the soft reset button with the stylus until the multi color bootloader screen appears).
5. While in bootloader mode flash the radio to 3.39
6. While in bootloader mode flash the DCD 3.1.6 ROM
7. After reboot install the Verizon carrier cab. Call verizon and let them know you have hard reset your phone so it can be re-authorized with their network.
everything looks good, what i would do though is flash the 3.39 sprint rom to get the radio. and you may not have to call verizon i just got a replacement phone and flashed up did the *22899 and everything worked with out having to call and get a a key.
s10onn2o said:
everything looks good, what i would do though is flash the 3.39 sprint rom to get the radio. and you may not have to call verizon i just got a replacement phone and flashed up did the *22899 and everything worked with out having to call and get a a key.
Click to expand...
Click to collapse
another suggestion i've seen somewhere else is to turn the phone into flight mode prior to flashing... not sure if it works but would be interested to know
also: DO NOT FORGET to soft reset just beforethe customizations run (when you are finished flashing and the phone reboots itself for the first time..)... you do NOT want the sprint customizations to run, on your Verizon device.
nickles96 said:
also: DO NOT FORGET to soft reset just beforethe customizations run (when you are finished flashing and the phone reboots itself for the first time..)... you do NOT want the sprint customizations to run, on your Verizon device.
Click to expand...
Click to collapse
if it's your first time you won't know when the sprint customizations are running. so just don't hit the screen or anything until AFTER you flash a DCD rom
the 0ne said:
I have spent the last few weeks reading all the threads located here on XDA-Developers and on PPCGeeks regarding upgrading an OEM Verizon XV6800 to a custom ROM.
Click to expand...
Click to collapse
I was in the exact same spot just a few weeks ago, flashing my XV6800 for the first time. I researched and prepared like you have and I think you're ready to pull the trigger.
My only advice is to use the SD method to flash the radio and OS ROMs. I wasn't able o connect via USB after upgrading the radio and the microSD method was incredibly easy and far faster than USB seemed.
Dialing *228 was all I needed after the process was complete, no new A-Key needed or manual entry of provisioning data.
Just remember, when in the process of flashing your phone, keep calm & carry on.
VX6800 upgrade procedures please
I too have read all the post on this and PPCGEEKS and have issues within myself. I start out with a high confidence level and after you get through a page or two of; yes, but do this instead ..... you are left with nothing but total confusion and contradictions. My confidence level is then well down the ladder.
I (we) would all like to hear from a VERIZON VX6800 owner (no sprinters please, sorry) who has actually done this with step by step instructions. Please don't assume we know anything, many like myself are knowledgeable in technical fields but not with PPC's.
This is my most serious concern. I ONLY have access to machines running Vista. I have heard that something, don't know what, will stop at 11% some people say not. What might stop and why? Ive also been told that there are new drivers for 'mobile device center' that fix this problem but no driver dates or version No's are posted anywhere. Any advice here would be helpfully also.
I know several folks who are also waiting for me (the guinea pig) to do this and they will follow.
Thanks for the time all have put into this effort.
All of the instructions and options for flashing are up-to-date in the Wiki.
I own and operate an xv6800, I used the methods listed in every sticky to flash my first time, never had a problem.
I have always used DCD's ROMS and used whatever he had posted in whatever thread for every ROM/kitchen. The man is thorough in putting the necessities in his threads.
Now I just flash whenever, no problems. I run 32 bit vista and xp on my machines and neither gives a headache.
The wiki is your guide to a successful upgrade. Study it.
Nonetheless, for those wanting VZW-specific instructions, here's how I upgraded my XV6800 to radio 3.39.10 and dcd's 3.1.2 a couple weeks ago.
I take no responsibility for anything you do to your device.
Code:
I. Upgrade bootloader
A. Establish an ActiveSync connection via USB
B. Execute Hard-SPL-MFG.exe to upgrade the bootloader to 2.40
[url]ftp://up.ppcgeeks.com/Titan/Users/ImCoKeMaN/roms/Hard-SPL-MFG.exe[/url]
Follow the steps in the command window closely - they are very clear
II. Format a microSD card for installing radio and OS ROMs
A. Using a card reader attached to your computer, format a microSD card into FAT32 with an allocation unit/cluster size of 1024
1. Open a command prompt and type
format ?: /FS:FAT32 /A:1024
where ? is the drive letter assigned to the microSD
III. Use microSD to install Radio ROM
A. Download radio 3.39.10
[url]http://rapidshare.com/files/113794877/radio339.rar[/url]
B. Un-rar
C. Copy RUU_signed.nbh to your microSD card
D. Rename RUU_signed.nbh to TITAIMG.nbh
E. Insert microSD card into phone
F. Force into bootloader by pressing POWER+CAMERA+RESET
G. Bootloader will load and begin loading the ROM on the microSD
F. When radio upgrade is complete, reset phone and force into bootloader
IV. Use microSD to install OS ROM
A. Download the OS ROM (e.g. dcd_titan_3.1.2)
B. OS ROM will be .exe file. Use WinRAR to extract files, one of which will have an .nbh extension
C. Copy *.nbh (e.g. dcd_titan_3.1.2.nbh) to your microSD card
D. Rename *.nbh to TITAIMG.nbh
E. Insert microSD card into phone
F. If not in bootloader, force into bootloader by pressing POWER+CAMERA+RESET
G. Bootloader will load and begin loading the ROM on the microSD
F. When OS upgrade is complete reset phone, eject the card, reset the phone
You will more than likely need your USB-headphone dongle/adapter that came with the phone.
After I upgraded my phone, resetting the phone caused the bootloader to appear instead of
loading the OS. For whatever reason, with the 11-pin USB dongle this doesn't happen
and the OS ROM boots without a problem.
V. Follow on screen instructions and allow customizations to run. Phone will reset when complete.
VI. Install Verizon carrier cab, reset when complete.
[url]http://www.lifesnotsogood.com/dcd1182/titan/carriers/dcd%20Titan%20Carrier%20-%20Verizon.cab[/url]
VI. Dial *228, reset when complete
VII. From your phone, browse to [url]http://ota.wsync.com/[/url] to download, install the XV6800 Over The Air sync client
After I upgraded the radio I wasn't able to load the stock OS and was unable to establish an ActiveSync connection via USB, thus was unable to use the RUU method. Using a card reader and microSD method to flash the new OS ROM saved my ass. I won't flash any other way now.
arnoldbabar said:
You will more than likely need your USB-headphone dongle/adapter that came with the phone.
After I upgraded my phone, resetting the phone caused the bootloader to appear instead of
loading the OS. For whatever reason, with the 11-pin USB dongle this doesn't happen
and the OS ROM boots without a problem.
Click to expand...
Click to collapse
Can you explain this more? Are you saying everytime i reboot my phone i will need the USB/Headphone adapter plugged in? Or just the first boot?
Also, I dont have a SD reader. Can i just copy the files to my SD card with the SD in the phone and connected via USB?
Thanks,
Mitchell
Are you saying everytime i reboot my phone i will need the USB/Headphone adapter plugged in? Or just the first boot?
Click to expand...
Click to collapse
For me, only about 1 in 3 reboots do NOT require the USB dongle. I have no idea why that is, I think it's an issue with the bootloader, but there are some threads on this board with more technical info. (I work in IT and carry a whole mess of cables in my bag, so it wasn't a huge concern of mine to tote the USB-headphone adapter around.)
Also, I dont have a SD reader. Can i just copy the files to my SD card with the SD in the phone and connected via USB?
Click to expand...
Click to collapse
Nope. You can read/write to the card but I don't think you can change the file system of the card while it's in the phone. Card readers are cheap, less than $20, and very handy to have.
After I upgraded the radio I wasn't able to load the stock OS and unable to establish an ActiveSync connection via USB. Using a card reader and microSD method to flash the new OS ROM saved my ass. I won't flash any other way now.
Also, when getting the required info before i start i dont see a key for security when i do a ##778. Is this ok/normal for verizon?
Thanks again!
After I upgraded the radio I wasn't able to load the stock OS and was unable to establish an ActiveSync connection via USB, thus was unable to use the RUU method. Using a card reader and microSD method to flash the new OS ROM saved my ass. I won't flash any other way now.[/QUOTE]
After the entire process was complete you are able to sync with the PC? Just not prior to doing the ROM update? Syncing is essential to me for backups etc.
Thanks for all the advice guys!!
wow, so i just remember i had a SD reader on my linux server. I went down and loaded up my VM of XP. Started to format my SD card and it blue screened and now I cant get my SD card to reconize in my computer or phone. I guess that a worthless piece of plastic now.. Ill try the USB method.
mitchell2345 said:
Also, when getting the required info before i start i dont see a key for security when i do a ##778. Is this ok/normal for verizon?
Click to expand...
Click to collapse
That was the same for me when I checked my EPST before upgrading. That's a good thing: you don't have an A-Key (security) now so you won't need one after flashing.
Rich W said:
After the entire process was complete you are able to sync with the PC? Just not prior to doing the ROM update?
Click to expand...
Click to collapse
Correct. However, now when I sync I have to use the USB/Headphone dongle. I can also sync via Bluetooth.
I just want to say thank you to everyone. I was able to get DCD 3.1.6 running by flashing the Sprint ROM and then flashing DCD 3.1.6. The only problem I'm having is getting Radio 3.39 to load. It will get to 8% and then the phone reboots.
If anyone is near newport news VA and wouldnt mind helping me out with upgrading my 6800 let me know. Ill provide the beer
Hi Folks,
I'm stuck in the tri-color screen for bootloader 1.06.
I have DCD 3.2.0 w/3.42.02 radio on the XV6800 and was trying to upgrade to radio 3.42.30. My system is Vista 32-bit.
I ran the Titan Relocker and it put SPL-1.06.0000 back onto the device and was planning on then putting 1.2 onto it.
Running titan_exitbl.exe says "Cannot open USB port. Please make sure, that USB connection in ActiveSync is disabled."
Unfortunately it is now stuck and even after ending the Sync Center service I can't get titan_exitbl.exe to pull it out of the Boot Loader.
Ideas? Thank you!
I could fire up an old XP laptop and try it from there.
Loaded ActiveSync 4.5 on an XP laptop, disabled USB connections, ran titan-exebl.exe and the device is booting now.
I'll continue on and see what else I can screw up.
Loaded SPL 1.20
Loaded 3.42.30
Loaded SPL 2.40
Device is back to working! Off to see if GPS is back after being lost with 3.42.02.
titan-exebl.exe
Where can I find titan-exebl.exe? Google doesn't turn up any results other than here?
titan_exitbl.exe
Never mind... just located it on my own hard drive!
Cheers!
Stuck on Bootloader
OK... I've tried titan_exitbl.exe, and it still doesn't work.
Here's my problem in chronological order:
1. I've been having a few problems (bugs) in my current custom ROM (PPC Kitchen 3.49 version), so I decided to re-flash to a stock ROM, see if the problems were fixed, and then try to flash back to a custom ROM.
2. I tried flashing to the Sprint 3.35 ROM. The RUU showed the progress bar on both my PC and the phone. But at 0%, I got a message saying "an error has occured" - or something to that effect.
3. I decided that the error was because I was running a custom ROM, and Sprint didn't like that. So I ran the Titan Relocker utility, thinking this would cure the problem.
4. I followed the steps on the screen and then got a message saying the relocker utility had completed successfully. The phone rebooted and went into the tri-color bootloader mode.
5. I retried the Sprint 3.35 ROM update, but got the same connection error, and the progress slider would never move from 0%.
6. I decided the phone had locked up and performed a reset with the stylus. The phone rebooted and went back into bootloader mode. The screen shows "TITA100 SPL-1.06.0000"
7. And that's as far as I've gotten. I've tried several hard resets using the buttons and the stylus together. I've tried removing the battery and reinstalliong... but the phone just goes back into bootloader mode.
I've tried both titan_exitbl.exe and UNI_Exitbootloader.exe, and neither utility seems to help. I get a message saying that "All data was sent... the phone will reboot now... please check your screen". The phone's screen blinks for a moment, and then returns to bootloader. Nothing can get it anywhere else.
I've tried different USB cables and ports. Activesync won't detect it, but the utility update software does.
When I run the Sprint 3.35 ROM update utility, I get an error at 11% saying "invalid vendor ID" and the update refuses to run. I tried to run the Titan Re-locker utility again, but it requires an ActiveSync connection. I've tried both enabling and disabling the USB connection in ActiveSync, but that seems to make no difference. The utility simply says no USB connection is available. The ROM update utilities will detect the device via USB - they just refuse to work with them.
I also tried running a DCD Tital 2.1.0 Bell ROM. The progress slider freezes at 0%, and then I get a message saying the RUU has encountered communication errors during the update. I've been through the recovery process the utiity suggests about a dozen times... it sill returns the phone to the bootloader screen.
So I'm getting pretty frustrated... does anyone have any ideas?
Try changing your spl back to 2.40.
Throwing it back into the tri color screen again and flash the sprint stock 3.35
But put it on the root of a fat32 formatted micro sd card in the flavor of under 2gb.
Just run the exe from your computer it will extract the files from the exe to some location on your computer, normally the ruu update folder.
There will be a ruu_sighned.nbh file locate it and copy it to the fat32 formatted card rename it TITAIMG.nbh
Let the phone boot into the bootloader and it should detect the file on the sd and update the rom for you, by stating loading ......
Then will prompt you to update press power key.
Sense you are not on sprint don't let the first time custimizations run ... pull battery once you get to your mobile today screen on first boot...
Use active sync or the sd method to update your rom to whatever you wanted originally.
Most full updates from carriers the ones that flash both the radio and rom will run regardless of the boot loader thats on the device.
Happy flashing
Just thought I'd toss in here that GPS does work, but I have to use GPS Viewer to get a lock on the satellites first.
softwind said:
OK... I've tried titan_exitbl.exe, and it still doesn't work.
Here's my problem in chronological order:
1. I've been having a few problems (bugs) in my current custom ROM (PPC Kitchen 3.49 version), so I decided to re-flash to a stock ROM, see if the problems were fixed, and then try to flash back to a custom ROM.
2. I tried flashing to the Sprint 3.35 ROM. The RUU showed the progress bar on both my PC and the phone. But at 0%, I got a message saying "an error has occured" - or something to that effect.
3. I decided that the error was because I was running a custom ROM, and Sprint didn't like that. So I ran the Titan Relocker utility, thinking this would cure the problem.
4. I followed the steps on the screen and then got a message saying the relocker utility had completed successfully. The phone rebooted and went into the tri-color bootloader mode.
5. I retried the Sprint 3.35 ROM update, but got the same connection error, and the progress slider would never move from 0%.
6. I decided the phone had locked up and performed a reset with the stylus. The phone rebooted and went back into bootloader mode. The screen shows "TITA100 SPL-1.06.0000"
7. And that's as far as I've gotten. I've tried several hard resets using the buttons and the stylus together. I've tried removing the battery and reinstalliong... but the phone just goes back into bootloader mode.
I've tried both titan_exitbl.exe and UNI_Exitbootloader.exe, and neither utility seems to help. I get a message saying that "All data was sent... the phone will reboot now... please check your screen". The phone's screen blinks for a moment, and then returns to bootloader. Nothing can get it anywhere else.
I've tried different USB cables and ports. Activesync won't detect it, but the utility update software does.
When I run the Sprint 3.35 ROM update utility, I get an error at 11% saying "invalid vendor ID" and the update refuses to run. I tried to run the Titan Re-locker utility again, but it requires an ActiveSync connection. I've tried both enabling and disabling the USB connection in ActiveSync, but that seems to make no difference. The utility simply says no USB connection is available. The ROM update utilities will detect the device via USB - they just refuse to work with them.
I also tried running a DCD Tital 2.1.0 Bell ROM. The progress slider freezes at 0%, and then I get a message saying the RUU has encountered communication errors during the update. I've been through the recovery process the utiity suggests about a dozen times... it sill returns the phone to the bootloader screen.
So I'm getting pretty frustrated... does anyone have any ideas?
Click to expand...
Click to collapse
please i have this problem how to fix this?
Please state your exact problem and what you did to cause it. Including all versions of rom and radio and bootloader.
drewcam888 said:
Please state your exact problem and what you did to cause it. Including all versions of rom and radio and bootloader.
Click to expand...
Click to collapse
Thanks!!! Ok, i cant remember eactly what is the v radio but i think 3.35 or 3.42 i cant remember exactly it's one of these. the SPL 1.06 Locked i cant unlocked i cant use titan_exitbl.... the SD update doesnt work stuck on loading.., i cant update from pc stuck 0% then Recovery Error help me. I My phone is bricked? Sorry for my english....
Did you try to install 2.4 unlocker?
drewcam888 said:
Did you try to install 2.4 unlocker?
Click to expand...
Click to collapse
Yes, i try from SD and nothing stuck on loading... from windows with RUU nothing 0% stuck and then UPDATE ERROR[262] now i don't know to do
2.4 doesnt use sd and it is run from a .exe. Make sure you aren't trying 2.47. Are you sure you tried this?
drewcam888 said:
2.4 doesnt use sd and it is run from a .exe. Make sure you aren't trying 2.47. Are you sure you tried this?
Click to expand...
Click to collapse
Ok, but how run from windows? If i cant connect via activesyncs the phone is on SPL mode i cant out of that and the msdos windows say "No device conected" when press enter from windows i cant unlock. Any idea? I'll try 2.47 but how run from windows with the phone en SPL Mode?
Please read. I said run 2.4 not 2.47. Put the phone in bootloader and it should say usb at the bottom. Then run 2.4 .exe unlocker. I think it should run without using activesync. And by spl mode do you mean the phone is in the bootloader.
drewcam888 said:
Please read. I said run 2.4 not 2.47. Put the phone in bootloader and it should say usb at the bottom. Then run 2.4 .exe unlocker. I think it should run without using activesync. And by spl mode do you mean the phone is in the bootloader.
Click to expand...
Click to collapse
Look i cant run Hard-SPL-MFG (Olipro 2.40 Unlocker) because when i run the Bat Or MSDOS Windows say "No device connect" question me if i want retray copy the file.
Ok so i guess it needs activesync. About your only option is to install a pregps rom so the phone will boot and then you can reflash the custom rom. Below is a pregps Verizon rom and radio that will work for 1.06 bootloader. Called rom 2.09.
http://forum.ppcgeeks.com/showpost.php?p=834294&postcount=4
drewcam888 said:
Ok so i guess it needs activesync. About your only option is to install a pregps rom so the phone will boot and then you can reflash the custom rom. Below is a pregps Verizon rom and radio that will work for 1.06 bootloader. Called rom 2.09.
http://forum.ppcgeeks.com/showpost.php?p=834294&postcount=4
Click to expand...
Click to collapse
No luck, method A SD Card Loading.. then cheking... then show a number corner 00028002 and say down Not allowed.
Method B, via PC and RUU then ERROR INVALID VENDOR ID.
Any idea? Thanks bro.
I think my phone is bricked... noway load the rom... i've tried load bootloader unlocked via SD last option and nothing!! damn this is so
I have an htc mogul that sits at the bootloader screen unless I have it plugged in to the power adapter. It is completely stock I never tried upgrading or unlocking it. I have re-imaged it about 20 times with the official 3.56 update from htc using the SD card and it goes through without problems. I can sync it with active sync but cannot run the exit boot loader program or the official ruu update via usb. Anyone have any ideas?
usually this happens when the phone is not unlocked and you are flashing a non stock rom. i was not aware that you could flash from sd with a stock bootloader so this seems like another problem.
i would flash nuespl from sd and flash the rom again.
--------------------------------------------------------------------------------
My Mogul was taken to a store that flashes phones to cricket. So it was ok before I took it to the store now. When I turn the phone on it boots to the smart mobility screen says "No Radio" then turns right off. I formatted my microSD card put the TITAIMG>nbh file on the card put my phone in the bootloader mode. Now my phone turns on and stay in the smart mobility screen w/ the No Radio still on it, and thats it. Is this phone dead? If not HELP!
forlovebeyou said:
--------------------------------------------------------------------------------
My Mogul was taken to a store that flashes phones to cricket. So it was ok before I took it to the store now. When I turn the phone on it boots to the smart mobility screen says "No Radio" then turns right off. I formatted my microSD card put the TITAIMG>nbh file on the card put my phone in the bootloader mode. Now my phone turns on and stay in the smart mobility screen w/ the No Radio still on it, and thats it. Is this phone dead? If not HELP!
Click to expand...
Click to collapse
If you paid someone to flash it, take it back! Did they give you back a non working phone? You'd think they would have tested it???
It sounds like you have a rom / Radio incompatibility problem. Or no radio at all. You say that you put the radio nbh on the card and put it into bootloader mode, but did you actually flash the radio? Did it come up with the grey screen and blue progress bar showing it was actually flashing the Radio rom?
Mogul Dead
No my phone did not do any of that stuff. And no I do not think that I flashed the radio I don't know how. I put the nbh file on the card insert it put it in the tri color screen and nothing happens. Man I am screwed. The kid at the store is saying that I did something & I did not. I have been reading alot cause I do not know anything about this flashing stuff and it does seem like there might be a radio/rom compatability thing going on cause the phone says no radio. I followed some forum steps to no avail.
dude if you get the tri color boot loader screen you did not kill your phone, all you need to do is flash your radio, witch is completely seprate from flashing your OS. just read the wiki and relax
The phone is telling you what is wrong "No Radio" you should be able to flash a radio via your sd card then flash a rom and all should be well. You just need to make sure the radio is compatable to the ROM. What is your ROM Version that shows on your boot screen. Also what bootloader is installed (tricolor screen)
I realize English isn't your primary language, but based on how you phrased your last comment, it sounds like you are inserting the SD card after the tri color screen.
The card needs to be in the phone before you press the 3 buttons for the boot loader screen, then it should see it.
BTC
Mogul Dead
Ok great sounds like from the replies that my mogul is not dead. Ok thanks guys. Also when I put the phone in the bootloader modethe tro color screen the card is already inserted, and the bootloader is SPL-2.40.Olipro. I do not know what ROM was put on the phone when it came from the store. So yeah I just might have to keep tyring to combine the right radio for the right rom thats on the phone.
find radio 3.42.50 and flash it via your sd card
then find the rom you want .....example.... DCD 3.2.6 and flash it via your sd card
then install dcd's carrier cab for you carrier and you should be up and running
Mogul Dead
How do I flash DCD's ROM to the sd card I never did this.
Do you have a ROM ready to flash? If so just goto the wiki link for the Titan's and do some reading. Everything you'll ever need to know about flashing is in there...
http://wiki.xda-developers.com/index.php?pagename=HTC_Titan
Focus on the radio first, once you get it flashed, then you can worry about flashing the rom.
For the rom (not radio) it's much easier, from the tri-color screen, plug in your USB cable and run the .exe file and it will flash.
However, get the radio updated first.
Try the 3.42.50 radio, I personally use 3.42.40 but they are very close and both support the same roms.
BTC
Freaking out as well
I'm stuck at the tri-color screen after updating the bootloader to 2.40.Olipro , I thought I could update the bootloader and still go into my Windows 6.1 install (and update the rest later).
I thought I totally screwed up my phone until I read this thread so hopefully there is still hope for this.
I do not have an SD card so I'm trying to do it the USB method by downloading the "ROM Update Utility" and placing the TITAIMG.NBH file into the RUU directory. It seems to work but stops at about 8% and the phone goes black then the PDA Phone ROM Update Utility pops up a:
ERROR [328]: INVALID COMMAND
This update utility cannot be used for your PDA Phone. Please check your Update Utility.
As you can imagine I'm absolutely panicked right now and will appreciate ANY help!
well save yourself some grief and buy a 2 gig microSD card. Then all you have to do is put the radio ROM on it, go into bootloader mode and let it flash. That is the safest and easiest way to do it. Also less, read nill, chance of bricking your phone.
Ok I'm heading out the door to Best Buy right now...
So once I get the radio installed, I then install DCD using the SD card method? Then the carrier cab?
I've already updated the bootloader to 2.40 using the USB method, will mixing these two cause any issues?
Now that I'm totally stuck at the bootloader, are there any precautions I should take before continuing?!?
Thanks so much for the help, I can't wait to get this going and maybe help out people like myself in the future
I got a 2gb card, formatted it to FAT32, downloaded 3.42.50 radio, renamed it and placed it into the root directory of the card.
I then put it into the phone, then did a POWER+CAMERA+RESET. It comes back to the bootloader screen doing nothing.
I've been reading around and it looks like I'm doing everything correct???? It just sits there and at the bottom it says "Serial"
EDIT: Oh you have to HOLD that combination for a couple seconds. Got it, I'll keep going on the process....
Here's what I just recently posted in another thread for someone wanting step by step instructions on how to flash the phone. He said he followed it and it worked so hopefully it helps you out.
1. Download everything you will need.
a) nueSPL 2.47 from http://www.nuerom.com/BlogEngine/pag...HTC-Titan.aspx
b) Radio 3.42.50 from http://forum.xda-developers.com/showthread.php?t=415364
c) The ROM from http://www.scottcrosler.com/
2. Back up your SD card and then format your SD card into FAT32 with less than 4kb cluster size. Open My Computer, right click on your SD card, select format and adjust the settings accordingly.
3. Run nueSPL 2.47 on your phone with your SD card in. It will reformat your SD card again and put the bootloader on it. When you reset your phone it will install the bootloader. Just follow the instructions.
4. Copy the nbh file from the radio rom onto your SD card and rename it to TITAIMG.nbh. Put it in your phone and put the phone into bootloader mode by pressing CAMERA, POWER, and RESET (the recessed button on the bottom of the phone) at the same time. When it starts up it should come up with a grey screen telling you to press POWER to continue flashing. Do this and wait for it to complete. When it is complete delete the nbh file from your card using your computer.
5. Put the phone into bootloader mode again using the same method as before. Connect your phone via USB to your computer and run the ROM flashing exe to flash the rom. Just follow the instructions that come up. It's easy. When that is done your phone has the ROM installed. If the USB method does not work for you, look for the largest .nbh file and copy it to your SD card, rename the .nbh file to TITAIMG.nbh again, and reset into bootloader again. You should get the same screen as you did when you flashed the radio. When it's complete the ROM is installed.
6. Run the CAB file from My Documents to extract all the other cabs. After that is complete look for the cab for your carrier and install that. Soft reset.
7. Your phone should work now.
I think that's it. Anyone else feel free to correct anything I probably have wrong... I just wrote that from memory. It's normally easy to do and you just follow the on screen prompts so I might've made some mistakes. I always just flash via SD now because it's so easy and I don't require a PC for anything.
Click to expand...
Click to collapse
The bold text is a step I left out for the other person but he figured it out.
Edit: Oh yeah, skip the part where you install the bootloader (step 3) since you're already running an unlocked bootloader and don't have a working OS on the phone to install 2.47. Once you have a working OS you can go ahead and update from 2.40 to 2.47 if you want a slight improvement in performance. It will not require you to reflash everything else again (or at least didn't for me).
Yes! 100% working. Didn't even have to call Verizon to reactive it, everything was ready to go as soon as I got the new rom.
Thanks for the help!
sprint no evdo no gps
phone works great but cant get online and gps does not work but phone service works ? damn and its only 24 hrs old i broke it using rom and raido from above
kyjelly said:
phone works great but cant get online and gps does not work but phone service works ? damn and its only 24 hrs old i broke it using rom and raido from above
Click to expand...
Click to collapse
Did you install the carrier cab?
Also see in EPST. If you use EVDO, may be login and pass are erased after flash. I had same problem with official Sprint ROM.
And what kind of GPS you are talking about? aGPS?