I appologize in advance if there is a lot of information about this but I have searched and searched and haven't found anything as of yet. I have the Verizon Touch Pro with the newest V2 stock ROM from several months back. Now I am interested and going back to a custom ROM. I have tried the latest HardSPL (I think it was 0.35) and when I run it I get "Loading..." on the TP and eventually "ERROR [260] : CONNECTION". If I pull the battery and put it back in it boots up to the way it was so clearly nothing is getting programmed. I have tried it on 3 computers and get the same thing. I had programmed it many times in the past successfully but that was before I upgraded to the V2 stock ROM. I'm wondering, is it that upgrade that is causing the problem? I have not tried via SD card yet but I plan to at some point today.
Thanks,
Tbone
Ok, I put the Verion HardSPL on my SDCard root and renamed it RAPHIMG.nbh. I forced the phone to the tri-color screen by holding power and volume down and then pressing soft reset. It flashed the tri-color and then went immediately to "Loading..." and has been there for 10 minutes. I do remember that when I did this previously it would ask if I wanted it to load the ROM and that is not happening. Any ideas?
Thanks,
Tbone
Ha, I got it. I put the ROM on the SDCard and then copied over VZW_TP_SSPL-Manual.exe and ran that on the TP. It initially showed "Loading..." and then quickly changed to "Checking..." followed by the option to load the rom on the SD card. Not sure if this is the only way to do it once you have installed the V2 ROM but it seemed to work at least with HardSPL. Interestingly, I then put the custom ROM on the SDCard and re-ran the SSPL and this time it went to "Loading..." and stayed there. So I reset and forced the boot in to the Tri-Color screen and this time it got past the "Loading..." screen without a problem. I'm definitely a bit puzzled over this but I'm now up and running with a custom ROM again.
Hopefully this might be helpful to others.
Tbone
Hi! its my 1st post on this forum, please avoid if its in wrong section.
Well, I have Jasjam & I have tried to Burn WM.6.5 ROM & at 96% I got error.
& after that when I Turn on my Phone, I see the start logo Screen & the phone stuck there, after reading few post here at XDA I have Accessed the boot loader tri-colour screen but don't know what to do with it.. I can see
Herm100
IPL-1.01
Herm100
SPL-1.06
I have read out a lot of posts saying Upgrate SPL , downgrade SPL etc etc
its the 3rd day I am continuously reading posts & every new post is making me messed up with new terms etc..
is there anyone who has the right solution for my Jasjam?
Hi there,
I'm stuck with the same problem as well. What I'd recommend is to wait for at least 30 minutes so that the HTC screen goes away and boots into windows. My TyTN got stuck at 81% in flashing a Schaps rom and the solution I found was to plug it in the charger, start up the phone and wait for a good 30 - 40 minutes. Once it booted into the home screen I reflashed it.
If that doesn't work, try the Mtty.exe tool from HTC. There are quite a bit of posts on how to use it. If it doesn't work then since your already in the tri-colour bootscreen, try reflashing the rom by running setup again. Hardspl if you have to but do not run active sync as it will not recognise the device. Hope this helps!.
PS: Incase your lost in which rom to use, try using a schaps rom. Search the forums for it. Pm me for further instructions since I've recovered my phone through these methods. Try to keep the forums clean!
Hello, I have an unrooted Hero from Orange (Spain) that enters in a boot loop. I have tryed everything to restore it but with no success. In the hboot menu it says "touch panel-fail" and even if I flash again the original rom from the hboot, it still gets in a boot loop.
First of all I will explain my case.
I had the Hero rooted, with custom roms etc, but when I bought a Nexus One, I gave my Hero to my brother. In September he told me that the official 2.1 had arrived to the Hero, so he wanted it instead of a custom rom, so I just proceeded to do so. I created a GoldCard, installed the 1.5 RUU of WWE, made the two OTAs and all OK. The last week (I think) he received a new small OTA, he updated successfully. My brother went to sleep with the Hero almost charged, but when he woke up, the Hero was off. Then, when he turned it on, and after a while (15mins or so) the Hero finally boot up, but the touchscreen wasn`t working and using it with the trackball the Hero was always prompting FC of android.process.acore (every 2 seconds more or less).
After watching that, I installed the official 1.5 of Orange hoping that it will fix it, but no way. Now it gets stuck in a loop while booting after the Orange bootscreen.
I tryed again to flash the WWE version, but with my old GoldCard doesn't seem to work (incorrect cid) and not being able to boot it up, I cannot create a new GoldCard or even root it.
I have tryed a lot of fastboot comands but I can do just little things because for the most useful things I need root.
Other thing that might be good to know is that when I plug the power to the Hero nothing happens, the led is not turning on, and I don't know how much battery I still have. Thank goodness that the battery was full before I moved the Hero to this infernal boot loop.
Please I will be so thankful if anyone can help me or just giving me any clue about how can I fix this.
I had the same problem on a refurbished hero I had. It had touchpanel fail in hboot and was in a constant loop.
I managed to get it to boot into android once by installing the ruu while in fastboot mode, however the touchscreen did not work and when I rebooted the phone it went back to the loop.
I sent the phone back for a replacement. If u check my previous threads ull see the thread icreated. In it I said that it had worked as that was when it finally booted but before I realised the sgreen didn't work
Sent from my HTC Hero using XDA App
Thank you for your reply, I will check your posts when I arrive home this evening.
hi.
I had the same problem and solve it by flashing this rom (goldcard needed)
http://shipped-roms.com/shipped/Her...io_63.18.55.06P_6.35.15.11_release_signed.exe
Hey all, I am having trouble booting anything onto my HD2 everytime i boot the phone i get stuck on the (tri colour screen) "Hardspl" i think..
I am able to install original HTC roms and custom roms via USB and Serial but after i install them and it says installation complete when the phone restarts it just gets stuck on the "Hardspl" screen again??
Any help is appreciated thanks
Here are some images to help
http://img29.imageshack.us/g/dsc0007riq.jpg/
(UPDATED)
How do i remove hspl ive tried installing an offical rom from the SD card but i still boot into this screen ????
Try this........
Power off the phone (make sure your battery is over 50%)
Turn on while holding the vol. down button.
You should be at bootloader (three colour screen)
If you have HSPL installed you should see "cotulla" and "HSPL" on the bootloader somewhere.
If youve been flashing official roms though this may have uninstalled HSPL.
I couldnt get the screenshots you linked to...
You can attach image files using the "manage attachments" button down under the text entry area.. (i think)
Id suggest trying to flash a stock/official rom just now until you get up and running.
With the phone at bootloader you should see the word "serial" at the bottom of the screen....
Connect via USB and wait for "serial" to change to "USB", this could take a few minutes.......
When you see "usb" flash the ROM from your pc......
You should make sure that you have the correct ROM for your phone, go to the HTC site and pump in your serial number.
If you still have problems after this then post back here with any error messages you might get...
Hope that helps.....
Thanks for the reply, for the link you need to add (http ://) sorry i should have mentioned that
but i just finished doing what you told be and it finished installing. it had the HTC logo on phone with loading bar as on PC screen no errors :S but im still stuck on the tri colour screen
I originally had android booted onto this mobile but the 3G was not working so i tried installing the HTC wm 6.5 rom that I downloaded from the HTC website but it would not get out of the tri colour screen after i installed it.
So i though it may have been the hardspl its self so i updated the SLP from 2.05 to the 3.03 one im currently on but it does the same thing
Hmm ok...
So the flash finished all the wasy to 100% and there were no error messages..
then the phone rebooted and went to bootloader (3 colours)...??
Restarting the phone just keeps returning you to bootloader??
Try turning off then back on while holding down both volume buttons and see what happens.
Which model of HD2 do you have and which ROM did you flash??
Yes thats correct.
When i turn the device on wile holding vol up-down i get a grey screen to
"This operation will delete all your personal data, and reset all settings to manufacturer default. press vol up to restore or press any other keys to cancel"
and im not sure what HTC HD2 i have..
Model: T8585 ?
I flashed the latest rom from the HTC website using the S/N
"RUU_Leo_S_HKCSL_WWE_3.14.831.3_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship"
Okay, get to that screen and press volume up to continue, this will perform a hard reset which is recommended after a flash, your device should then boot up, may take a few minutes as its the first time..........
ok, It finished in like less then 10sec but there was not skips did from 1% - 100% smoothly and says "Restore....Completed Press VolUp to boot"
So i pressed volume up and once again stuck on the tri colour screen
any more suggestions or is my phone dead?
Hmmm
Phones not bricked because 95% of the time if you can get to bootloader the problem can be fixed........
I have the feeling this is something obvious that Im not picking up on.
Chances are someone else will see this and point out the obvious but at the minute I cant think why it might be doing that......
You could try flashing the ROM from SD card.
Rename the file on your PC to "leoimg.nbh" and put it on a 2gb/4gb sd card, turn the phone off, put the card in, turn on and it should flash........
Like I said, i dont think your phone is dead, I think Im missing something obvious....
its weird because i can install roms, hardspl's and all that stuff it knows the phone is there and installs them but for some reason it never gets passes the hardspl stage.. on each boot.
it accually boots into the tri colour screen in a split second of turning the phone on
Its a longshot but is there any possibility that your volume down button is stuck in the pressed position.........
yeah i have installed off the SD card already. that took awhile but it says everything is ok and installsion has completed.
same problem though once i restart tri-coloured screen pops up.
Im afraid Im not sure about this one...........
I'll keep thinking and let you know if anything occurs to me.....
Im sure someone else will chip in at some point and point out the issue though.
alright no worries thanks for the help and time hopefully someone knows what the problem is.
Maybe if i uninstall the Hardspl? might totally wreck it and 100% brick my phone if it fails but I think its the only option ill have left soon
uninstalling hspl shouldnt cause any harm........
I didnt realise you had HSPL installed, I take it you instaled that after flashing the stock rom??
If you have HSPL installed......
Try to install a custom rom, ie an energy rom, just as an experiment........
dunno if youve seen the images yet conan, but unless its changed since, the OP has 3.03.0000
also, if he has magldr installed ( i didnt see it mentioned, but..) when you hard reset it takes just a few seconds, because it is only hard resetting magldr (at least thats my understanding, and would offer a reason why hard reset is so quick)
I suspect incorrect 3,14 flash, which didnt complete so its returning to bootloader,
so, OP, bootloader - hspl4 - 3.03.hspl - flash your 3.13 rom again, over usb.
ok thanks ill try that right now, also yes magldr was installed for android but i thought I got rid of it once i rebooted the offical HTC rom.
If this works im donating $20 to you right away no joke .. ive been trying to fix for 13hours straight
Australian icon said:
ok thanks ill try that right now, also yes magldr was installed for android but i thought I got rid of it once i rebooted the offical HTC rom.
Click to expand...
Click to collapse
sd card flash, right?
Step 1 of the flash is the spl gets overwritten by the one in the leoing.nbh rom (3.03.0000 in this case) and then the phone reboots, and starts to flash , , splashscreen (where magldr is), radio, rom.
BUT, the phone wont allow the flash to start because hspl is now gone, so it fails CID checks and stops, so doesn't remove magldr, radio, rom, nothing, it just stops. Further attempts at flashing fail because you teh user haven't notived the spl change, you assume the whole flash failed, and that hspl is still there.
You shouldnt be able to get that far normaly, it would fail before it even starts, on a stock spl, except that hspl was there, so the flash was allowed to begin.
Ok, so its on SPL-3.03.HSPL now then I installed the latest HTC offical rom with USB but still no go
also if it is resetting magldr how come it doesent load up like it used to after a reset
I managed to break my original HD2 a while ago and I've only just decided to replace it. I have another main phone but I loved that I could pretty much do anything with my old HD2. I had a bit of experience with installing cooked ROMs before moving on to installing Android and WP7 on it.
As I had a bit of experience with playing about with software recovery/updates, I decided to buy a phone that was described as "booting to a white screen" off ebay. I thought it would be a fun little hobby to get it working again.
My first few steps would be to get it to stock and start playing with it from scratch.
I booted into the bootloader and tried to flash a stock ROM but it kept freezing at 0%.
I've since managed to change the SPL version from 2.08 HSPL (I could get the phone to boot into MAGDLR 1.13, so they must've been playing with WP7 or Android NAND) to 3.03.
I downloaded and installed the stock 3.14 T-Mobile UK ROM, but it won't boot past the white screen with the HTC logo. If I pull the battery out to turn it off and try to turn it on again, then it gets stuck at a blank white screen with no HTC logo at all. I'm very confused and would like some help if possible. Thanks in advance.