Hi! its my 1st post on this forum, please avoid if its in wrong section.
Well, I have Jasjam & I have tried to Burn WM.6.5 ROM & at 96% I got error.
& after that when I Turn on my Phone, I see the start logo Screen & the phone stuck there, after reading few post here at XDA I have Accessed the boot loader tri-colour screen but don't know what to do with it.. I can see
Herm100
IPL-1.01
Herm100
SPL-1.06
I have read out a lot of posts saying Upgrate SPL , downgrade SPL etc etc
its the 3rd day I am continuously reading posts & every new post is making me messed up with new terms etc..
is there anyone who has the right solution for my Jasjam?
Hi there,
I'm stuck with the same problem as well. What I'd recommend is to wait for at least 30 minutes so that the HTC screen goes away and boots into windows. My TyTN got stuck at 81% in flashing a Schaps rom and the solution I found was to plug it in the charger, start up the phone and wait for a good 30 - 40 minutes. Once it booted into the home screen I reflashed it.
If that doesn't work, try the Mtty.exe tool from HTC. There are quite a bit of posts on how to use it. If it doesn't work then since your already in the tri-colour bootscreen, try reflashing the rom by running setup again. Hardspl if you have to but do not run active sync as it will not recognise the device. Hope this helps!.
PS: Incase your lost in which rom to use, try using a schaps rom. Search the forums for it. Pm me for further instructions since I've recovered my phone through these methods. Try to keep the forums clean!
Related
I have an HTC branded G4 Wizard. It got corrupted during a bad flash and will no longer accept new ROMs. It only boots to the boot loader screen which displays the following info:
Upper right corner says: RUU
IPL 2.17.0001
SPL 2.25.0001
Any time I try to flash a ROM, it gets about 1/2 way through and then the phone disconnects and goes into an endless loop of booting to the Boot Loader screen, and then rebooting. To get it to stop I have to remove the battery for more than an hour to fully drain power.
I've searched the forum and Wiki but can't find any info specific to recovering a G4 and I know I can't use IPL/SPL designed for a G3.
Any help appreciated.
have you read this?
http://forum.xda-developers.com/showthread.php?t=298613
if not it might help you, i've used it a couple of times
Simply download and install the Wizard Love Rom
Thanks for the pointers to these topics.
I just tried installing the Wizard Love ROM. The updater made it to 96% then the Wizard disconnected and starting it's looping boot, reboot cycle. I'm going to leave it sit with the battery removed and try again in a while. Maybe it will get all the way to 100% if I try several times.
At 96% can take more than 10 mins to complete
Be patience
It wasn't that I disconnected the device at 96%. The device dropped it's connection and rebooted itself. That was it has been doing when I tried to flash another ROM. On the positive side, it has never made it this far before rebooting since the problem started. So, I'm thinking positively and viewing this as progress.
have you try a provider based roms ... like aku 2.2?
Actually, I didn't see any htc branded Wizard...What is the htc model for your Wizard?
I think I had the same problem Monday, see the link to my post.
I have a G3 and don't know how to load a ROM on a G4 but when I left my phone off all night with the battery out it stayed on longer without shutting off and going into the endless loop.
I see you have a different IPL than your SPL, I don't know if that is a problem with a G4 but I understand it is with a G3.
Good luck, I know your pain.
http://forum.xda-developers.com/showthread.php?t=319084
well i did the silly thing and did a flash upgrade on my atom exec to WM6 v7
it went 100% restarted fine
but now!!!!! im stuck on the align screen it doesnt listen to my taps, if i move my fingers all over the screen it eventually pick it up but it isnt accurate enough so keeps restarting the test align session... HELP PLEASE i have meetings comming up and need this phone
i can get into boot loader mode but when i connect phone to laptop it doesnt connect active sync while in bootloader mode...
can i skip this screen align somehow
You are not suppose to upgrade the EXEC with the ROM .
Check out the WIKIPEDIA ATOM solutions page for assistance.
I think therz a way to get back to the ORIGINAL ROM , ask a SENIOR for help also search the forums for older posts , i remember someone with ths same problem as yours
really? i just ran the utility here:
http://forum.xda-developers.com/showthread.php?t=333165
without making any changes to it
how do i go back to original pleaseeee help someone... if i got in boot loader mode and run the same upgrade utility (as linked above) it lets me click upgrade but then quickly says connection failed and then my bootroom reads:
"please use DSUU in OS mode and sync with PC first!!!
where do i get original and how do i do it please... maybe there should be a sticky for stuff ups like this
wow no one is kind enough to help... ive tried this:
http://forum.xda-developers.com/showthread.php?t=331818&page=1
but it freezes on 6% and i took the advise read in the wiki to hard reboot then run DSUU , and it does the same thing (stuck at 6%)
well now i have the wm5 starting but its stuck again on the tap the screen? ignoring my taps...
could it be my screen is stuffed? although it worked before the flash
okay !!! progress!!!! ....'
ive finally called o2 and put their rom and it works to a certain point, the align screen detects my taps but it just keeps repeating over n over n over asking me to keep taping around the screen???
Hard Reset
I think hard reseting it once should solve the issue...........if it doesn't try reflashing it once again.....worked for me............brute force is needed sometime
no i figured its screwed my digitzer somehow so im asking for calibration data in other post
hey there been a member for sometime and have tried to search for a solution to my problem and am abit confused.
and sorry if its such a newb question (dont burn me for it)
i have an o2 atom exec (using RC3 rom with touchflo) and yesterday i /soft reseted/ the phone because it was acting funny, after the reset it would be stuck at the startup screen and would not load past that the whole day, so i waited and re-tried in the evening.. the same thing occured... i was at the time able to load into bootloader (MN2) but then could do nothing else.. so i searched throughout the forums and found a post by 'chartreux' http://forum.xda-developers.com/showthread.php?p=1684559&highlight=EBOOT.NB0 but had not read the entire post and proceeded to load (mn1) onto my phone via mini sd card and it worked, my phone was working again, it performed a hard reset and restored it to factory settings (ie: calendar, msgs, contacts, software all gone) and phone is working normally again... since it has done this i wanted to update to 'wm6.1 atom exec rom' just to be up-to-date and have synced it via activesync and have run "DSUU" but my phone just restarts and loads the current rom i have installed! and just repeats everytime i have tried (have tried atleast 50 times)
so my main question.. is my bootloader dead? i know my phones not bricked since its still working perfectly im just not able to upgrade my ROM but can still do everything else (such as browse through files, run programs, make calls)
and last of all.. can anybody please help?! as i am at the point running the phone over with my car!
and once again am sorry for the stupid question.. =/ and thanks for hearing me out!
cheers!
stylistik said:
hey there been a member for sometime and have tried to search for a solution to my problem and am abit confused.
and sorry if its such a newb question (dont burn me for it)
i have an o2 atom exec (using RC3 rom with touchflo) and yesterday i /soft reseted/ the phone because it was acting funny, after the reset it would be stuck at the startup screen and would not load past that the whole day, so i waited and re-tried in the evening.. the same thing occured... i was at the time able to load into bootloader (MN2) but then could do nothing else.. so i searched throughout the forums and found a post by 'chartreux' http://forum.xda-developers.com/showthread.php?p=1684559&highlight=EBOOT.NB0 but had not read the entire post and proceeded to load (mn1) onto my phone via mini sd card and it worked, my phone was working again, it performed a hard reset and restored it to factory settings (ie: calendar, msgs, contacts, software all gone) and phone is working normally again... since it has done this i wanted to update to 'wm6.1 atom exec rom' just to be up-to-date and have synced it via activesync and have run "DSUU" but my phone just restarts and loads the current rom i have installed! and just repeats everytime i have tried (have tried atleast 50 times)
so my main question.. is my bootloader dead? i know my phones not bricked since its still working perfectly im just not able to upgrade my ROM but can still do everything else (such as browse through files, run programs, make calls)
and last of all.. can anybody please help?! as i am at the point running the phone over with my car!
and once again am sorry for the stupid question.. =/ and thanks for hearing me out!
cheers!
Click to expand...
Click to collapse
what version of your bootloader now? MN2 or MN1? if still MN1 please read again the thread to update your bootloader to MN2 (since your device is ATOM EXEC).
and after done, please check when you run DSUU, see on the left bottom whether have a drop down box or not? if yes then choose "ALL"
hope this can help to solve your problem.
hey! thanks for the reply mate!
but im not sure i cant check the version of my bootloader...
wont let me get into it by pressing camera+SR or camera+off button..
just boots straight into the operating system.
and, as for the DSUU it just restarts the phone after i choose all, and goes through to the today screen on the phone, and as for the DSUU update its stays at the screen which shows "The current software is now being updated from your device."
followed by an error appearing after a few minutes showing " No download target was found!!" even though my atomexec is synced
which is then followed by the "connection error" screen.
please help.. this is seriously pissing me off...
stylistik said:
hey! thanks for the reply mate!
but im not sure i cant check the version of my bootloader...
wont let me get into it by pressing camera+SR or camera+off button..
just boots straight into the operating system.
and, as for the DSUU it just restarts the phone after i choose all, and goes through to the today screen on the phone, and as for the DSUU update its stays at the screen which shows "The current software is now being updated from your device."
followed by an error appearing after a few minutes showing " No download target was found!!" even though my atomexec is synced
which is then followed by the "connection error" screen.
please help.. this is seriously pissing me off...
Click to expand...
Click to collapse
try to downgrade again your bootloader to MN1 (please do it step by step). as long you can secure your bootloader, hopefully you can resolved your problem.
remember to upgrade again to MN2 once you able to downgrade to MN1 before try flashing to wm6.1.
good luck.
still cant access bootloader.. even when trying DSUU it just boots straight into the operating system, when trying to update and also i tried the MN1 bootloader again and tried to get into it... still nothing.. it just resets, i tried it with my 4GB mini sd, 2gb msd, and a 64mb mini sd.. could not get into it... sigh...
Ok try a deep breath and read all the posts on dead boatloaders and other upgrading problem posts through and through. Then try to change ur USB cable and what system are u using i.e XP or Vista????
thankyou kindly, for the suggestions i have been reading through alot of posts and tried alot but.. nothing so far.. i guess its not too bad since its stuck on windows mobile 6 with abusalzas rom..
im just annoyed i cannot upgrade to the latest 'rom' and since my phone 'had' to perform a hard reset why not update so yeh.. and i am using windows xp for my computers os.
Did u change the USB cable mate, once I had to do it and the interesting thing is that the same USB cable was working perfectly for other things but causing problems when connecting to my Atom Exec.
yeh tried it with my old v3 cable didnt work has the same outcomes.. sigh.. i might try that dead bootloader hardware and software recovery from this post by Alex_Beda & 1stMASTER
http://forum.xda-developers.com/showthread.php?t=336278
what you think?
although my phone doesn't resemble there symptoms list.. as it still works and everything just cant get into the damn bootloader.. :/ when done manually and when trying to upgrade..
Did u read this mate ?????
http://forum.xda-developers.com/showthread.php?t=358442
You just try the DSUU with upgrade "OS" only and not "ALL".
alright cheers buddy! ill try it out and i hope it works!!
bahh.. didnt work =( just restarted my phone and gave me a connection error screen on my computer....
Actually i have the same problem, i tried to get into the bootloader by press and hold camera + reset button it just restart and load the WM
Dead atom exec
My atom exec having problem ( dead ), so after press camera reset sw my atom can booting normaly but touch screen function only for entering password and then touch screen not response anymore. I check the system information by touch the button (manualy) but IMEI not ready and Radio not ready.
Pls someone can help us.
o2 atom bootloader
hello
my o2 atom bootloader screen mn1 dignostic manger screen remains after rom flashing .i tried flashig orginl rom and pedvit rom but bootloader screen comes again .not starting my mobile please help
I've just been trying a few ROMs and whist trying to downgrade from 3.5 to 1.2 spl I found myself stuck in the bootloader white loading.. screen.
If I pull the battery it boots the ROM fine but whenever I entered bootloader or ran a ROMupdateutility to try a reflash I got this white screen.
I've searched for an answer on here with no joy and actually started this post to ask for help but I've just removed the SD card and it went straight to the normal bootloader screen and I'm re-flashing as we speak.
Just thought I'd complete the post for any future searchers.
Thanks
Mine has been stuck on the screen every time I try to re-flash (which actually has saved me from wasting a lot of time as well ....) but I did the same & now have the Bootloader.
Back to the endless routine of upgrades and downgrades then.
Hi I am a newbee in tis forum - yesterday i installed the CleanBlack2ReloadedOffice in german on my XDA Star - it worked perfectly ...
Today i wanted to upgrade the radio from Nike_Radio_1.58.16.27 to the better one Nike_Radio_1.58.21.23_25.65.30.04S_Modded.
Result: the flashing stopped with 99% an now i am stuck on this boot-screen and my phone is a brick :-( It says:
RUUNBH
NIKI300
SPL-1.16.0000
CPLD-4
I tried several things to get the phone alive - but nothing helped every trial failed with the grey screen and a 0% on it - some 5 Minutes later aborted with error. What can I do?
Thanks in advance to any helpful hint!!
tip
It seems that you have not installed hard spl first
Hi 2alive - quite right. I copied the sspl-1.16-nike.exe on the device and started the Update. It stuck on 99% - ended with an error.
But now i am not able to install hard spl or anything else? I allways get the 0%-Load-Screen on the device and after 10 Minutes an 262-Error.
Is there hope to get this device running?
Any helpfull advices? Thanks in advance
Usually Device Boot Loader original can be updated using ROM Upgrade Official from HTC website. Just try it and hope it will restore your OS. When you are in Bootloader screen and connect to PC using USB Cable just run the ROM upgrade official setup and just click the status connected to ActiveSync (although you are not connected to ActiveSync coz you are already connected to USB) and go next and update, It still can upgrade the ROM.
FYI : Just Remember Original Bootloader can not upgrade Radio or ROM from Modded / Custom ROM setup thats why you need to install HardSpl to allow upgrade from Modded version.
Thank you lion _snake1 for your Tipp.
I tried now to load every shipped original rom - but the Rainbow-Start-Screen does not go away. Is there any other chance to get this device again working? Did anyone made experiences with this strange behavior?
I really would be glad, if there is a "howto" get into a working communication process between my "Pc" and my phone?
Is the ROM Upgrade Official setup can run 100% and finish ?
If it can then maybe the problem is in your Bootloader.
Maybe you can go to forum section "xda-developers - General discussion - Upgrading, Modifying and Unlocking" and start the same thread since that section is special for Upgrade and Mod and i think some of experience people usually online there.
hi lion_snake1
thank you for your advice - there i did not found any solution till now. I tried to load everything - but all originals or mods will stand on a grey screen with 0 % an dont move- then the error comes with 262. I already tried to boot via sd-micro-card - did not work - the device blinks a moment - as if it is searching fo rsomething and sticks again in the rainbow bottloader ....
i am looking for a step by step help for mismatched romupdates.... also with commando-lines-hacks....