hi,
I have One Herm 100 Imate Jasjam.It came to me for the repair,i searched and found the solution in the forum.The device has no IMEI and No Gsm and booting properly but no network.So i follow this thread "How to unbrick your bricked hermes" Link is http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
and found that the solution from the given Table after answering the all the questions,so the solution is (1.) Flash Hard-SPL (2.)Flash any radio in NBH format.Do both steps using SSPL+ActiveSync.
i could succesfully Flash the Hard-SPL.Now i put the Phone is bootlaoder mode i can see that the HERM100 IPL-1.04 and HERM100 SPL-2.10.Olipro.
But when i am performing the second step that is "Flash any radio in NBH format.Do both steps using SSPL+ActiveSync" (i downloaded the Hermes_Radio_1.50.00.00_108) from the support and trying to upgrade the radio but it always starts and stuck at updating 0% and not moving further and an error message popping up saying error 260 and 262.I read the read me and followed all the instructions but all the time i am getting the same error.
So please guide me what to do?
Waiting for replies from all the PDA Guru'S.
Regards,
Moderate.
If you had of read you might have found this is a problem with VERY low probability of you fixing it....
So saying, try the sd card method, You have Hard SPL on the phone, do this....
1. Format an sd card fat32 and copy RUU_signed.nbh on it. Rename to hermimg.nbh.
2. Insert sd card and put Hermes into bootloader - Hold down power, OK button above flywheel and then use stylus to reset... Hold all three in until you get to the tri-colour screen A.K.A bootloader.
3. It should recognise the herm flash file so follow the prompts...
If the Radio only rom doesn't work you can try a stock rom... Best if you try the carrier rom it was initially.
If that doesn't work, at least you have a nice PDA.....
Good Luck, you're gonna need it...
Cheers...
ultramag69 said:
If you had of read you might have found this is a problem with VERY low probability of you fixing it....
So saying, try the sd card method, You have Hard SPL on the phone, do this....
1. Format an sd card fat32 and copy RUU_signed.nbh on it. Rename to hermimg.nbh.
2. Insert sd card and put Hermes into bootloader - Hold down power, OK button above flywheel and then use stylus to reset... Hold all three in until you get to the tri-colour screen A.K.A bootloader.
3. It should recognise the herm flash file so follow the prompts...
If the Radio only rom doesn't work you can try a stock rom... Best if you try the carrier rom it was initially.
If that doesn't work, at least you have a nice PDA.....
Good Luck, you're gonna need it...
Cheers...
Click to expand...
Click to collapse
First of all thanks for the reply.
I am using Carrier NBH and following your instructions and now it is updating the image lets see,it has just started.i willl update here with results.
i Can see on screen the following details.
================================================
HERMIMG.nbh -
IPL - OK
BOOTLOADER - OK
SPLASH1 - OK
SPLASH2 - OK
EXTROM - OK
GSM -
OS -
Update in Progress...
================================================
Regards,
OOps it stopped at some percentage say between 10 to 15.And it didn't move further for more than 30 minutes.
I removed and trying to flash via pc but it is hanged at 14% now for a very long time.what could be the problem.Could this be hardware or i am making misake somewhere.
Dunno,,
regards,
moderate said:
OOps it stopped at some percentage say between 10 to 15.And it didn't move further for more than 30 minutes.
I removed and trying to flash via pc but it is hanged at 14% now for a very long time.what could be the problem.Could this be hardware or i am making misake somewhere.
Dunno,,
regards,
Click to expand...
Click to collapse
Congratulations! You now have a Hermes PDA
I have something like this now
I tried flashing CRC13 via USB
at about 92% it failed. It attempted to recover and failed again.
I used a 1gb lexar MicroSD, copied the CRC rom's RUU_Signed.nbh to the card as HERMIMG.nbh
reset holding Power and OK buttons.
It flashed 000680002 and went back to the tricolor screen
Herm100
IPL-1.04
Herm100
SPL-2.03
I'm trying the KITL method from http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
Any other suggestions?
If I let it attempt to boot normally, the CRC splash screen comes up, then brightens for a second, then goes blank. The charge indicator will respond to power, and the USB will make the PC "bu-bumb" but AS will not connect, explorer will not see it, and RUU_Wrapper will not detect it
Thank god... I DL'ed a factory OS, extracted it and ran the RUU_Wrapper and that did install
then installed CRC13 naked
All is well
Radimus, HARD SPL YOUR PHONE.... You were EXTREMELY lucky... If you are thinking about reflashing your phone you need Hard SPL ver 7 installed... It won't guarantee you won't brick your phone but will offer a safety net so you may be able to fix it.
Cheers...
for some reason the hardspl7 will not install via AS for me...
Is it OK to do it via sd card using SSPL-HERM.exe
Yep, thats actually my preferred method of flashing. Check out post 1160 on page 116 of this thread for instructions - http://forum.xda-developers.com/showthread.php?t=296722
You can also flash Os'es with the sd card method. Once you've Hard SPLed your Hermes you won't need to use sspl.exe but make sure your battery is more than 50%.
I personally wouldn't flash the radio rom from the pc as there are too many things that can go wrong. SD card all the way...
Cheers...
done.
sspl.exe rules
HERM100
IPL-1.04
HERM100
SPL-2.10.Olipro
Click to expand...
Click to collapse
Related
Hi all,
i've found an alternative approach to flash any firmware on HERMES 200.
I had a problem while i was trying to upgrade my WM5 Vodafone 1605 to WM6.
My bootloader is SPL-1.09, and i've tried in many ways to install Hard-spl v7 but here is what was keeping happening:
- I try to flash my Hermes with hardSPL v7 and each time:
- Hermes switch to bootloader mode and display
HERM200
IPL-SSPL by Des
HERM200
SPL-1.09.ds
- Activesync lose the connection
- Windows XP send popup with new USB device and ask me to install the new device (no idea of driver not found by default)
- RUUWrapper display error 260
Click to expand...
Click to collapse
Here is the solution:
- Download the firmware u wish to install on your device
- Unpack the firmware (right-click and Extract)
- copy the .nbh file into you microSD card and rename it as: HERMIMG.nbh
- put SSPL-HERM.exe into you device (you can get this app in this site too)
- now put you microSD card into you device and run SSPL-HERM.exe
- enjoy
I'm just an unexpert user that has tried many times to upgrade his device reading other posts on this forum. So pls correct me if i've said something wrong!
I wrote this post just cause i was going crazy and i wasn't able to find a solution like this around the sites
Hope this help somebody!
PS: I'm sorry for my bad english!
RUUWrapper display error 260? try to disable your firewall, flash again, and you will see it works.
regards chief
i've got the same problem with my hermes...
i don't know how to fix...when i start the flashing process the device switches in the bootloader mode and then nothing else is happening, there is no connection to the pc. i tried to switch off the firewall, i changed the cable, i changed usb port but nothing happens...
does anybody know what i shall do?
its the same fault as anvillani describes, the only thing different is that i dont get herm200 but herm300
Do you guys do ANY research before trying this???
Go to this thread - http://forum.xda-developers.com/showthread.php?t=296722
Go to page 116, post 1160 and READ it step by step, juymp ahead and this WON'T work. Just make sure you use a 2Gb or less sd card. INSTALL HARD SPL 1st.... Then you can use the sd card method (just skip the steps using sspl.exe as you should now have Hard SPL) to update your roms....
Cheers...
i really dont know what you want to say with this...
i tried the normal procedure to flash hard spl to my device and i tried the method anvillani suggested and both didn't funtion.
so my question is what i should do...
Follow the link and instructions in my previous post. It will allow you to install Hard SPL using the sd card method. You do need to be able to get to the today screen though.
After reading anvillani's post I'll add that the sd card MUST be 2Gb or less and has to be formatted FAT32. You have to name the .nbh file hermimg.nbh with NO speeling (sorry, spelling :b) errors or it won't work.
Cheers...
I inherited this device from a moron. So Moron --> Moron i suppose.
I am trying to flash any rom. I just flashed Schaps 4.40. Works great. It flashed with spl 3.00 from olio.
When i intentionally put it in bootloader mode, it goes to SPL 2.03
When i try to flash a ROM, it runs SPL 1.09, then returns with error 260 ( I have rebooted and reconnected, still same issues).
I am running Vista 64 bit. I have no idea what is going on. I get the same herror when i try to run the Hardspl7 loader.
Any help or ideas are greatly appreciated.
try flashing through the microsd card, see wiki for instructions
i shoudnt have to do the workaround with the storage card, that doesnt fix the issue. Isnt there a way to get rid of my outdated bootloader 1.09? That seems to be the problem here.
how the hell would you even go from spl2.04 to 1.09?? are you even freaking sure your spl is 1.09 and its not just the sspl?
use the sd card method and install hardspl, with it, i just posted a howto in the hardspl thread. if you still dont think you have to use this "workaround" then by all means go ahead and start troubleshooting, error 260 is an open port error, search for it, the step you should take to troubleshoot are out there
I'm in the same boat, when I do flash the boot screen shows SPL1.09. If I manually enter boot screen it shows SPL2.03. It did this after I ran the olipro sim unlocker and tried to upgrade it back to hard SPL V7
stesul411 said:
I'm in the same boat, when I do flash the boot screen shows SPL1.09.
Click to expand...
Click to collapse
yes yes, everyone who is running the upgrade using the force spl is also having this "problem".....unfortunately, there is no known fix for this "problem" cause i dont think anyone really wants to fix it.
XtreMe_G said:
how the hell would you even go from spl2.04 to 1.09?? are you even freaking sure your spl is 1.09 and its not just the sspl?
use the sd card method and install hardspl, with it, i just posted a howto in the hardspl thread. if you still dont think you have to use this "workaround" then by all means go ahead and start troubleshooting, error 260 is an open port error, search for it, the step you should take to troubleshoot are out there
Click to expand...
Click to collapse
It never was 2.04, it is 2.03. And i followed your directions:
"ok, lets see if i get this right.
1. download hardspl v7 from the first post.
2. extract ruu_signed.nbh and rename it to HERMIMG.nbh
3. copy it to a microsd card, make sure the card is formatted as fat32
4. download sspl-herm from here
5. extract SSPL-HERM.exe and copy it to your phone.
6. insert sd card and run sspl-herm.exe on the phone.
7. you should see the tri-color screen and then it should change to this
8. press power button to start flashing
9. reset when you get the msg that its done."
This did not work. extracted, renamed, extracted, ran sspl-herm.exe from the phone, and it goes to the spl-1.09.ds bootloader, and never changes to the other screen.
Why does no one want to fix this? How many others are experiencing this issue?
Thread has been renamed in order to classify the problem better.
http://forum.xda-developers.com/showthread.php?p=2055596#post2055596
Hi All,
I'm new to the PDA-world and the Hermes. I'm trying to Hard SPL my Hermes, but it fails everytime.
When I run 2.10 - Hard-SPL-V7, it kills activesync and my connection is lost and I get always the message "error 260, Update error".
I have the latest framework edition and tried it on 3 pc's (1 Vista, 2 XP)...
What am I doing wrong?
Hope somebody can help me....
Kind Regards,
Micha
1). dont connect to active sync. open active sync and untick "allow usb connections".
2). put hermes into bootloader and connect to usb.
3). run ruu_wrapper.exe
should update to hard spl....
dont forget to tick "allow usb connections" again or you wnot be able to sync..
error 260 is an open port error.
if you wish to flash new os would advise to use sd card method. its safer than using the computer. just make sure you have greater than 50% battery power. happy flashing
Thnx, will give it a try.
First I have to flash HardSPL before I can flash a new OS, don't I?
yep, sorry, should have said run the ruu_wrapper for hard spl. My bad...
im having the same problem. I also tried the way ultramag recommended but i also received the same ending. After time i try i get the Error 260 Update error. Im running SPL 2.04 and the HTC WM6 rom from the HTC website. Does any one know what the problem is?
ultramag69 said:
2). put hermes into bootloader and connect to usb.
Click to expand...
Click to collapse
NOOOOO, that won't work, you need the SSPL to deploy to the phone, if you're running stock HTC bootloader this won't work at all, otherwise we'd have no need for Hard-SPL
hey olipro, then how would i fix this. Im running the stock rom from the HTC website with no hacks. Im trying to load PDA Corners V9 rom. Any ideas on how to fix? thanks!
Take a peek at the guide i wrote about updating the hardspl. Theres some explanation about why we need to use SSPL and the procedures.
http://www.mrvanx.org/hermes_guide/hardspl
thats the guide i used. it still gives me the error. I even unchecked "allow connections" cause i read somewhere that that would help.
i did this two days ago on my phone, im running windows vista on my home laptop and got any number of errors and problems trying to do it via sync with the phone (even after reading the vista troubleshooter, with the drivers etc)
What i ended up using was the memory card upgrade, dump the file onto the memory card and go into bootloader with the card installed.
worked fine doing that way, maybe less risky as there is no chance of the usb cable coming out.
just make sure you have a good battery charge on the phone.
Help Help Help w bricked 8525
I got into this position trying to upgrade WM5 to WM6 from HTC site.
Process got to 20% and just stayed there.
I reconnected usb cable and got a vendor id error
Then I get the Error [260]: CONNECTION
I have read a lot of posts and have tried the sd method (although i am not 100% clear) and all i get is the screen with four colors, red, green blue and white.
I believe this is the bootloader? I have downloaded RUU_signed.nbh, renamed it to hermimg.nbh, installed on root of my SD card and held OK, soft reset and power button:
My display reads:
HERM100
IPL-1.04
HERM100
SPL-2.03
This is where my journey ends.
All post indicate that the device can be reflashed and have the OS reinstalled. I can't get there from here.
Can anyone please help?
blackdog9692 said:
I have read a lot of posts and have tried the sd method (although i am not 100% clear) and all i get is the screen with four colors, red, green blue and white.
Click to expand...
Click to collapse
How big is your SD card? Flashing only works with cards <2GB. Also, sometimes certain cards just don't work for flashing, and just swapping to a different card fixes the problem.
I assume you searched the wiki, and found the relevant pages on the Hermes (including SD Card Flashing and other things about flashing/upgrading) there?
Still Lost
My SD is 2GB and I have tried many times but i just keep getting the 4 color screen. rt now when i boot from the SD my screen goes white and displays "Loading..." and then returns to bootloader screen. When i attempt to flash the rom via PC to WM5 or WM6 i get the Error 260, i also get a vendor ID error sometimes.
How can i find the key 8525 thread that i am told has the answer to my delima? I keep picking up bits and pieces but am missing some key steps and tips.
blackdog9692 said:
My SD is 2GB and I have tried many times but i just keep getting the 4 color screen. rt now when i boot from the SD my screen goes white and displays "Loading..." and then returns to bootloader screen.
Click to expand...
Click to collapse
That sounds like the SD card is formatted incorrectly. Make sure it's formatted using fat32, nothing else will work.
Still not there from here
Thanks for your help. Before I formatted the SD FAT32, nothing would happen doing the bootloader reset. OK/ON/reset button.
After format and only the hermimg.nbh file renamed as indicated, I then get what looks like the loading process but back to the bootloader screen.
Q1: This is an AT&T 8525, it was perfectly fine before failure from WM5 to WM6 (process froze at 20%), what is the RUU file that I need to put on SD??
Q2: After "Loading ..." I try the WM5 PC upgrade of ROM via USB cable, I get the load process to appear to work but it gets to 1% and the phone reboots and the PC reports error [294]: Invalid vendor ID. If I do this again I will get the Error [260]. Ive repeated the process several times.
Is this the normal course to take or should the "SD Method" (with the WM5 or WM6 RUU.. file) complete the process to a working OS?
Q3: Is my situation hopeless? ATT will take my out of warrantee 8525 and reflash for $129. Reading the threads it seems that like me this can be done by me, this is my desire.
Q4: I still am confused by some basic terms and assumed steps. I dont understand "Hard SPL" or OLI's IPLs/SPLs and when and when to use them.
The newbe guide has been off line. I will look again. Is there a single place to read about "radio PDAs and the 8525 and understand the software build and custom options?
Sy for the long post. But still want to fix if possible or I will be force to mail in for ATT repair.
Thank you all.
blackdog9692 said:
Q4: I still am confused by some basic terms and assumed steps. I dont understand "Hard SPL" or OLI's IPLs/SPLs and when and when to use them.
Click to expand...
Click to collapse
Oh boy, you haven't installed HardSPL? You are walking a bit of a line there mate...
HardSPL is a custom boot loader that makes bricking your phone when flashing much harder to do, and helps large amounts in the recovery process if you phone does brick.
Does the phone boot at this point? If so, do not try flashing the phone again. Go get a copy of HardSPL and install it, then try flashing from the SD.
I still wonder why people didn't read before bricking...
Anyway, you should start reading now and wiki is your friend. Your SPL is 2.03, so look at the bottom of the page (there is only one solution till now, so good luck with that):
Code:
1. Boot OS using KITL+PB
2. Do no disconnect your HERMES till the end of the step 6
3. Download SSPL on HERMES by wifi from ie explorer
4. Launch SSPL then flash Hard-SPL from your computer
5. Put your hermes in bootloader mode
6. Flash any radio in NBH format from your computer
Still researching and working this bricked 8525
Thanks for coming to my aide. I believe that I have Hard SPL'd my device. I downloaded Olipro's Hard SPL v7. extracted the RUU_ file and renamed to hermimg.nbh.
I then put it on an SD card and held the keys and reset. The device displayed a white screen and "Loading..." appeared. Afterward the 8525 returned to the stipped boat loader screen and that is where I am now.
Some of the help i receive and read on wiki threads has me confused with what to do next and how "exactly" to do it.
It does seem that I am not alone and people have fixed their phones and the process to do this is on the forum. I'm just still missing something.
Help me further if u can.
Thank you.
blackdog9692 said:
Thanks for coming to my aide. I believe that I have Hard SPL'd my device. I downloaded Olipro's Hard SPL v7. extracted the RUU_ file and renamed to hermimg.nbh.
Click to expand...
Click to collapse
FYI: bad form to PM someone and post the same thing here. Keep it in the thread so others can be helped as well.
As I replied in the PM, if I'm understanding your post correctly, the phone boots to the tri-colour screen?
What text is showing on the screen? This will tell if HardSPL is on the phone or not.
jdc said:
What text is showing on the screen? This will tell if HardSPL is on the phone or not.
Click to expand...
Click to collapse
We already know that the phone is without HardSPL, according:
My display reads:
HERM100
IPL-1.04
HERM100
SPL-2.03
This is where my journey ends.
Click to expand...
Click to collapse
There is small chance (read my previous post) to unbrick device with SPL2.03 so better try to get this back from where you take it.
And please, change topic, because this brick isn't HardSPL fault at all.
Edit: oh dear, it's even not your topic ...good game, I'm off
Alright so about 3 weeks ago i started upgrading my hermes. i started off by downloading the 2.10.Olipro hard spl and radio version 1.16.00.00. i unlocked the cid as well. then i put this rom on with no problems. http://forum.xda-developers.com/showthread.php?t=458456
Now everytime i try to load anything from my usb my phone gets stuck in bootloader and i get a error 260 message saying my phone is not connected to my pc. ive tried multiple cables and updated my activesync. even if i try to use the sd card method i get stuck in bootloader yet again. ive been trying everything i can find on this forum for the last 5 hours and i feel something like this.........im quite the newb in this stuff so i figure this is a easy fix that i keep overlooking.
SD card method....
1. Make sure SPL is 2.10 olipro & battery is charged.
2. Format 2Gb or less sd card FAT32 and copy .nbh file to it. Rename to hermimg.nbh.
3. Insert sd card into Hermes and reset into bootloader - hold ok button above flywheel, power button and reset with stylus. Hold in until tri-colour (bootloader) screen appears.
4. Follow the prompts.
Easiest and safest way to flash ROMs...
Cheers...
If you need to use sd card method to flash Hard SPL, read post 1160 on page 116 of this thread - http://forum.xda-developers.com/showthread.php?t=296722
or just give him the direct post ultramag69
http://forum.xda-developers.com/showpost.php?p=2048832&postcount=1160
Yeah, you could, but this way he has to search a bit and get used to the ui at XDA-Developers... Might even decide to use the search function, horrors....
I was actually going to add that he might use the search function too but thought i would give you room to reply
When i tried to install any firmware the progress stop at 11% and the Hermes only turn on in bootmode, any idea??
rmorera84 said:
When i tried to install any firmware the progress stop at 11% and the Hermes only turn on in bootmode, any idea??
Click to expand...
Click to collapse
I had that problem and few more with my Hermes.
While it didn't help me, this suggestion by ultramag69 may help you...
Use the sd card method to flash a new rom, instead of a USB cable/Windows computer.
1. Format a 2Gb or less sd card to FAT32, copy the large 50MB-90MB .nbh file onto it and rename to hermimg.nbh
2. Insert the card into your Hermes and reset to bootloader (hold OK & POWER and push RESET for a sec with the stylus)
3. If you haven't stuffed up the other steps, follow the prompts.
Hope this helps!
Just one other thing summoner, make sure you have Hard SPL V7 installed. Otherwise the ONLY rom I'd try flashing like that is the SHIPPED STOCK ROM. Its so the CID will be recognised and won't cause a brick.
rmorera84, unless you've installed Hard SPL V7 then find the SHIPPED STOCK ROM and flash that, anything else may permanently brick your Hermes.
If you have Hard SPL V7 (IPL 1.04, SPL 2.10 oli) then flash what you like...
Cheers...
- Installed latested Orange rom, that I know of - SPV_M3100_ROMUpdate_1007
- installed Hard SPL 7 & applied SIM unlock/super CID
- re-installed TNT TNT.19199_Professional_Hermes
The result is:
IPL-1.01
SPL-1.40.Olipro
I suppose I should upgrading the radio rom now!?
I am told don't try fixing what isn't broken - and it is working. 3G iNet, Phone, WiFi, BT - all good atm.
Or is there a particular update I should still install?
Thanks!
SUMM0NER, you're using an older, not so safe version of Hard SPL. The Hermes is downgraded to SPL 1.40 when you sim/CID unlock your phone. Best idea would be to re-install Hard SPL V7. Its a later version that seems less prone to problems when flashing.
Go back to the Hard SPL thread and get Hard SPL V7. I had the same thing happen to me when I unlocked the Hermes, nearly cost me my handset.
The steps are unlock Hermes, Install Hard SPL then upgrade OS.
Cheers...
Do I need to re-apply the OS rom file?
I just reinstalled Hard SPL7, now shows as IPL-104, SPL-2.10.Olipro.
Thanks!
My hermes only work whit this rom:Schaps_WM6Pro_ESN_3.54b-0808_Full
Because whit any other rom they stuck at 11%.
This is the info or the phone:
IPL-1.01
Spl-1.40.Olipro
Whit the first rom the htc boot but the phone funtion don´t work.
rmorera84, refer to my last post.
SUMM0NER, no. You have loaded the os, the reason you put Hard SPL V7 is if you want to upgrade the radio rom (not a good idea unless you are experiencing problems) or wish to change the os. Just means recovery is easier than if you didn't have it.
Cheers...
Many thanks ultramag69.
rmorera84 what branding is your Hermes (ie: Orange M3100, T-Mobile Vario 2, Vodeaphone V1605 etc...)?
Can I assume your Hermes is working right now?
If it is download and install HardSPL V.7 (attached to the bottom of the first post!)
Ones done verify that it installed correctly by holding the OK & Power button and pushing reset for a sec. The screen should display the coloured bars and say towards the centre: SPL-2.10.Olipro
It´s Cingular 8525, i could install the HardSPL V.7, now what rom i can flash??
You didn't confirm if it is working right now!?
If it is not working, try one of the official WM5 Cingular roms from this list. If that worked apply HardSPL 7 and take it from there.
Ones you downloaded the Cingular rom update you will have to keep unpacking the .exe files until you come to the actual .NBH file (WinRAR works for me).
Then follow ultramag69's instructions on flashing the rom via memory card.
Works, now i have this info:
HERM100
IPL-1.04
HERM100
SPL-2.10.Olipro
I download the official Cingular WM5 rom, but. i don´t know how install this rom by memory card, could you help me??
Excellent!
Try downgrading to the Cingular rom via USB. Just double click the EXE and follow the instructions.
To use the memory card method follow these steps...
0. unpack the .exe file containing the rom with Winrar (right-click exe then choose "Extract to...\")
1. Format a 2Gb or less sd card to FAT32, copy the large 50MB-90MB .nbh file onto it and rename to hermimg.nbh
2. Insert the card into your Hermes and reset to bootloader (hold OK & POWER and push RESET for a sec with the stylus)
3. If you haven't stuffed up the other steps, follow the prompts.
The reason to use the memory card to upgrade a rom, rather than a usb cable, is to cut down on failed upgrades (dodgy Windows/usb port/usb cable/etc..).
All working? Try upgrading to a Hermes rom that didn't work previously.
Any rom you can find in the Hermes section. Go to the WM06 part of the forum, theres a sticky at the top with about 50 older roms and you'll find other roms there too (latest is wm6.5).
Cheers...
i install the official WM5 AT-T version the WM6 AT-T, but, i still whit the no-gsm problem, can i flash i radio? or what i can do??
You may not be able to fix this, if you know what the original SHIPPED STOCK ROM was and can find it, then flash that. It may not work, if it gets stuck at 11% - 17% mark it means the radio ROM is stuffed and the memory area is corrupted. Not fixable.
You could also try, if you know what it is, the original radio rom by itself. Again, if you can't get it to work, you have a PDA but won't work as a phone ever again. Sorry to be the bearer of bad news.
Im to having the same problem, it keeps going back to the 2.1.Olipro boot loader.
I tried the memory card option and it starts to install but then stops.
Does anyone have and sugestions?
Cheers
Help Help
Hi, I got my Hermes 8525 in boot mode what i did is to install this Schaps_WM6Pro_WWE_4.00_Full.exe now my hermes is working but i want to unlock it..what can I do cos everytime i try got in to boot mode again..any help tks.,..