i tried to flash imatejasjam radio with hermessim cid unlocker v3a
but the radio doesnt flash it take o% then doesnt proceed
and give errors now handset stuck at bootloader mode.
bootloader is 1.40
any suggestions mates. i want to recover my handset.
any help will be apprecaited
regards
unlock trigger
try this mate
http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
Related
Hi
Im hopeing someone can help me I know this issue has probably been discussed loads of times and im a muppet for doing it, I was looking at different ROM's for my Orange M3100 and thought I would go for the IMATE JASJAM ROM so I could get MSN messenger .... I unfortunatly selected the TELSTRA 1.06 Bootloader ROM and downloaded instead of the 1.04 ( I should have read the posts on this ROM before!). Now I am stuck in bootloader 1.06 and as I have read the only way to get back to 1.04 is to flash with a ROM that is the same as my carrier (Orange UK).... the only Orange ROM is the Romanian one thats just been put on the WIKI, I have tried with this but its coming up Vendor ID error... if anyone can help or tell me how I can go back to 1.04 id be grateful? if not do I just have to wait until orange UK bring out a ROM with bootloader 1.06 ????
Thanks a lot ! James UK
Same problem with Cingular bootloader 1.06
I've the same problem with Cingular 1.34 bootloader 1.06, I try to downgrade with same bios CID (CWS__001 as I read on this forum) to bootloader 1.06 but I receive an error "WRONG VENDER ID" (also if i leave connected my PDA and I restart RUU utility it give me the same error)
I've also tried to install another vendor bios with bootloader 1.06 as suggested but I receive the same error message!!!
Emanuele
Unfortunately, you're stuck unless you either a) wait for a bootloader for your CID or b) pay the $38 to do the super-CID unlock. There's a thread on that stickied, so if you decide to do it, help them out by doing the usb capture.
Thanks... I have already unlocked the device with IMEI-Check.co.uk do you mean this? If I have unlocked it then do you think I should run IMEI check again on the device and it may unlock the CID ? cheers, James
If you run the imei tool again (with the latest version of theire software) it will reverse your bootloader to 1.04 and make your device super CID
ok. it says this in the tri-color screen:
HERM100
IPL-1.04
HERM100
SPL-1.40.Olipro
ok. so i download the Hard-SPL-V7 and it works. and it says that up there on my boot loader. but what is my bootloader version? 1.40? or 1.04? and what is this talk of the SPL-2.10.Olipro. how do i get that? im confused
oh another thing. why does it freeze on the GSM- part when i use the SDcard method? anyone? help thank you
the latest bootloader is 2.10.Olipro (the latest official one I've released for general consumption)
to flash it, please do remember NOT to put your phone in bootloader and to have activesync synced.
IPL is Initial Program Loader, and is generally not too exciting.
SPL is Secondary Program Loader and this one handles flashing etc and is the one with the exciting crap you need to patch.
have you been able to flash GSM with SD or somehow else ?
I ve asked how to fix it about 100 times on this forum and my device is still bricked
After SIM and CID unlocking my 8525, then reflashing, it showed No GSM when booting and would sometimes lock up at the operator boot screen. After some searching, I ran mitty.exe and described, rebooted, then tried to run the unwrapper.exe again to reflash the radio, NO GO!...stuck at bootloader screen (IPL 1.01, SPL 1.40)
What can I do?
Microsoft Platform Builder Method?
Any help will be greatly appreciated,
GunRunner
Try this table here http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
Use a MicroSD card to flash, the best way not to brick your phone.
Hi all,
I just bought the Olinex SimUnlocker and for some reasons when I try to unlock the radio I get an error 226 at 100% of the flash process.
Then my phone reboot and I'm stuck to the bootloader screen.
The only way to make my phone work back is to flash it with my carrier's ROM.
But once I reflash the SPL + sim unlock with the Olinew unlock I get an error at 100%.
My raphael was alrealy security unlocked with Olipro.
What can I do to avoid this error?
Please help
Thanks in advance
Are you talking about how to use olinex tool ? Or that you're trying to flash a radio after using olinex tool?
Hi, I was unlocking my htc 8525 at&t but i was using vista and my cell keep in Type 2a: When the phone boots, it goes directly to bootloader mode (tri-color screen)
what can I do to fix it... tks
Whats the info for your SPL?
Hi, I got my Hermes 8525 in boot mode what i did is to install this Schaps_WM6Pro_WWE_4.00_Full.exe now my hermes is working but i want to unlock it..what can I do cos everytime i try got in to boot mode again..any help tks.,..
SPL- 1.40
Try unlocking it with Windows XP
hi, i tried in win xp but keep the same in boot mode...
On the PC, in activesync settings, untick "Allow USB Connection".
Put Hermes into bootloader (tri-colour screen) and then run the RUU_Wrapper.exe file of the unlocker program. Follow all the instructions to unlock your Hermes and once its unlocked put Hard SPL V7 on it BEFORE flashing any thing else. After flashing Hard SPL V7, go back to bootloader and check SPL is 2.10 oli.
You now have a Hermes that is easier to recover if somehing goes wrong with a flash, excluding radio rom flashes.
Cheers...
Hi, canu put the link of the program u told me to use..tks for your help..
RUU_Wrapper.exe, Its included in any rom you want to flash. Its how you flash using the PC...
Hard SPL is in the sticky of the Hard SPl thread in upgrading section.