Hi all,
I just bought the Olinex SimUnlocker and for some reasons when I try to unlock the radio I get an error 226 at 100% of the flash process.
Then my phone reboot and I'm stuck to the bootloader screen.
The only way to make my phone work back is to flash it with my carrier's ROM.
But once I reflash the SPL + sim unlock with the Olinew unlock I get an error at 100%.
My raphael was alrealy security unlocked with Olipro.
What can I do to avoid this error?
Please help
Thanks in advance
Are you talking about how to use olinex tool ? Or that you're trying to flash a radio after using olinex tool?
Related
Hi
Im hopeing someone can help me I know this issue has probably been discussed loads of times and im a muppet for doing it, I was looking at different ROM's for my Orange M3100 and thought I would go for the IMATE JASJAM ROM so I could get MSN messenger .... I unfortunatly selected the TELSTRA 1.06 Bootloader ROM and downloaded instead of the 1.04 ( I should have read the posts on this ROM before!). Now I am stuck in bootloader 1.06 and as I have read the only way to get back to 1.04 is to flash with a ROM that is the same as my carrier (Orange UK).... the only Orange ROM is the Romanian one thats just been put on the WIKI, I have tried with this but its coming up Vendor ID error... if anyone can help or tell me how I can go back to 1.04 id be grateful? if not do I just have to wait until orange UK bring out a ROM with bootloader 1.06 ????
Thanks a lot ! James UK
Same problem with Cingular bootloader 1.06
I've the same problem with Cingular 1.34 bootloader 1.06, I try to downgrade with same bios CID (CWS__001 as I read on this forum) to bootloader 1.06 but I receive an error "WRONG VENDER ID" (also if i leave connected my PDA and I restart RUU utility it give me the same error)
I've also tried to install another vendor bios with bootloader 1.06 as suggested but I receive the same error message!!!
Emanuele
Unfortunately, you're stuck unless you either a) wait for a bootloader for your CID or b) pay the $38 to do the super-CID unlock. There's a thread on that stickied, so if you decide to do it, help them out by doing the usb capture.
Thanks... I have already unlocked the device with IMEI-Check.co.uk do you mean this? If I have unlocked it then do you think I should run IMEI check again on the device and it may unlock the CID ? cheers, James
If you run the imei tool again (with the latest version of theire software) it will reverse your bootloader to 1.04 and make your device super CID
I Have read allot of data, unbrick tutorials and upgrades suggestions...
but I Still haven't found what is the correct upgrade stages.
As far as I have read from the unbrick suggestions, I've reached to the following order:
1) Upgrading SPL (Enabling KITL)
2) Unlocking
3) Upgrading radio
4) Upgrading Windows
Can someone confirm or recommend/add other steps ?
During the upgrade steps, will the HERMES be usable ?
Unlock first THEN hard spl.
DONT mess with your radio if it works fine, as this is part that can COMPLETELY brick your phone(you may be able to use as a PDA but not gonna be a phone EVER again.)
Load an os(either a stock one OR one of the cooked roms our TOP chefs cook up.), most come as OS only, no radio.
Hope this helps.... Cheers
It is useless for me, I cannot unlock the phone, due to different locking technique.
there are few posts about a locked Jasjam, with no olutions.
all the unlocking process went well, 3 times...
after the unlock process, when I insert the sim, it connects to the network, (indicated with 5 lines) and after about 5 seconds, it disconnect and says :
"The system detected an invalid SIM card"
and asks for unlock code.
now I have the following versions:
IPL 1.01
SPL 1.40.Olipro
Radio 1.16
any ideas ?
The Solution
To unlock Cellcom (Israel) JASJAM, As weird as it sounds, you should disable/deactivate/uninstall/whatever the EYRON Multi language support, which comes pre-installed.
I'll let the experts explain it.
I Dont know if it works for Orange-il Tytn too.
please consider note this in unlock guide ?
Now, which version of HARD-SPL with KITL should I Install... (Link will be helpful)
Please note that I Only Unlock the SIM, and not SuperCID, the .BAT file of the unlocker says:
"CID Unlock: will make your phone SuperCID forever, don't check this if you are unsure. HardSPL will do same effect without loosing warranty."
Olipro ver 7(Hard SPL) This is considered the best for the layman, if you want to develope roms/ programs then you should use ver 9. However, ver. 9 does throw up an error after flashing. There is no problem and olipro said he'd get around to fixing it, BUT.......
Hope this helps...
ultramag69 said:
Olipro ver 7(Hard SPL) This is considered the best for the layman, if you want to develope roms/ programs then you should use ver 9. However, ver. 9 does throw up an error after flashing. There is no problem and olipro said he'd get around to fixing it, BUT.......
Hope this helps...
Click to expand...
Click to collapse
I have upgraded to Olipro V7
When I Boot into bootloader, I see:
IPL-1.04
SPL-2.10.Olipro
But I Still not get any sign of KITL according to this threat (Step 5).
The Device is booting normally, as if I'm not holding any bottons.
How can I check if KITL enabled ?
Do I need KITL while using OLIPRO V7 ?
Orenk,
Have you read the Mr Vanx guides or the wiki? Here are the links:
http://www.mrvanx.org/cms/
http://wiki.xda-developers.com/
WB
i tried to flash imatejasjam radio with hermessim cid unlocker v3a
but the radio doesnt flash it take o% then doesnt proceed
and give errors now handset stuck at bootloader mode.
bootloader is 1.40
any suggestions mates. i want to recover my handset.
any help will be apprecaited
regards
unlock trigger
try this mate
http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
hi respected members and mods
i am having problem in htc niki i have done hard spl as described in sticky thread of htc security unlock and then ran the step 1 it went successfull but step 2 is not working for me when first step completes phone goes off an comes back on and it says in sticky thread that we have to put phone in boot mode so i manually put the phone in boot mode and disable usb in active snyc settings and then i ran the 2nd step but it stucks i can see only 2 lines written
=== Niki SuperCID and Security Unlocker (c)2008 by jockyw2001
=== Donations happily accepted, paypal to [email protected]
and after this nothing happens i press enter to exit from application but it doesnt go off i am not able to exit then i manually clicked on cross sign on right top corner to cancle the app and then i re flashed the orignal radio but phone still locked any help please i have done 2 to 3 times but not luck
befor you try to unlock ... flash a old 1.58 radio!
NetrunnerAT said:
befor you try to unlock ... flash a old 1.58 radio!
Click to expand...
Click to collapse
thanks for your reply do i have to flash the 1.58 radio after step 1 or when plz?
phone's orignal radio is this R 1.58.16.27 which radio should i write
im having this problem and now my phones prompting for an unlock code
stasis-666 said:
im having this problem and now my phones prompting for an unlock code
Click to expand...
Click to collapse
Unlock code? I assume that wiuld be to unlock your SIM.
Please note, you have to remove both SIM and SD card for the unlocking procedure.
I have HardSPL and flashed a british NIKI under "Orange" and was able to use it in the US with a US Sim card under T-Mobile.
I just tried to use it with a French SIM card under SFR and I get a
"SIM Lock" - Enter unlock code Message...
Is there a solution without calling the original carrier?
Hi i have 1 hermes Spv m3100 and phone when comes to me was on and need to unlock network code
i do unlock using HTC_Hermes_SIM_CID_Unlock_v3 unlocker
in the half of flashing my pc goes off
and phone cant flash now.
i cant do HSPL for write any rom .so i need to flash official rom but i cant find that.
Now phone can go in bootloader mode but cant turn on fully and hang on windows logo.
When i go in bootloader is same this
HERM100
IPL-1.00
HERM100
SPL-1.11
Phone is ORANGE and come from UK
Now what shall i DO?
hamed_karamouz said:
Hi i have 1 hermes Spv m3100 and phone when comes to me was on and need to unlock network code
i do unlock using HTC_Hermes_SIM_CID_Unlock_v3 unlocker
in the half of flashing my pc goes off
and phone cant flash now.
i cant do HSPL for write any rom .so i need to flash official rom but i cant find that.
Now phone can go in bootloader mode but cant turn on fully and hang on windows logo.
When i go in bootloader is same this
HERM100
IPL-1.00
HERM100
SPL-1.11
Phone is ORANGE and come from UK
Now what shall i DO?
Click to expand...
Click to collapse
you must hard reset device and try to Flash ROM again ,,,
for official Rom you can get in http://www.shipped-roms.com/index.php?category=windows mobile&model=Hermes
Tnx to replay
i had tested before hard and soft reser but nothing
I also try many rom from there and all of them have a Invalid Vender ID error
I tested these file
Code:
SPV_M3100_ROMUpdate_1007.exe
SPV_M3100_ROMUpdate_0407.exe
RUU_Hermes_O2_UK_3.62.206.2_6275_1.50.00.00_108_Ship(3).exe
HTC_TyTN_WWE_3.54.255.3_6275_1.48.00.10_108.exe
But still same
In first step of turning on phone wrote NO GSM and fast disappear
Why no answer?
Can we hspl phone when phone is in bootloader mode?
hamed_karamouz said:
Why no answer?
Can we hspl phone when phone is in bootloader mode?
Click to expand...
Click to collapse
could of course , why not ...??
you live connect to a usb synchronization and Flash ROM by clicking hspl.batch
finished it! {All of it depends on understanding and Your lucky}
I am using this Hard-SPL-V7
But it cant find device
The Update Utility cannot connect to your PDA
But when i have flash rom it flashed and come out of flash in 1% and invalid id error
and i cant do Hspl using MMC always this error
00068002